Related
touchscreen was working today morning, took battery out for 2 hours, turned it back on and it was working abit weird, and now i cant press any touchscreen buttons atall!
So no softkeys (pick call, home etc.) and nothining on the big screen! I can turn on the phone, press the power button and volume buttons, see my home screen get calls etc.. hard reset twice, took battery out, nothing does it .. gonna try flash it but dont think itll do it ... and ideas?
Im in uk aswell if that makes a diff
Dear All,
I have similar problem. Usuallí I use on my HD NRG ROM. About 3 weeks ago I updated to the latest NRG WM 6.5 23xxx ROM with Sense 2.5 Maxmanila version, and since this upgrade the touch screen position moving randomized up or down from 2 mm to 30mm!!! After this ROM I tryed updating each newer version, but not changed nothing. I need realign the screen about 10 times / day!!! The phone I never dropped or cracked.
Can help me somebody what happened with my HD?
I had this happen to me yesterday. I was surfing on my phone as per the norm. Put my phone down. Got a txt, picked it up and it wouldnt allow me to access it. I thought it must be a freeze as it has happened occasionally.
So I restarted.............and nothing. No response AT ALL from the touch screen.
I have noticed the oily spot problem on the most part of my screen, and thescreen doesnt have that little give it used to when using it (paranoia possibly)
So I can only assume something has given within the screen. Ive been searching all day on the internet for causes and fixes but nothing has come up.
The volume and power buttons work but I cant do anything at all with the phone as its obviously all touch based.
Is this a screen replacement job then or is the whole phone goosed?
Roheelshah if you turn your phone off do you have the massive oily screen thing?
Any help is most appreciated....
I had the same thing, a oily spot, but it was there for months, then i noticed another new spot (looked like a tiny tiny burn) and thats when it stopped working completely... ive ordered a new screen which should be comming in a few days, im hoping thats the issue
will let you know if it works ....
keep me updated if you find anything
thanks!
NECROSTONE said:
I had this happen to me yesterday. I was surfing on my phone as per the norm. Put my phone down. Got a txt, picked it up and it wouldnt allow me to access it. I thought it must be a freeze as it has happened occasionally.
So I restarted.............and nothing. No response AT ALL from the touch screen.
I have noticed the oily spot problem on the most part of my screen, and thescreen doesnt have that little give it used to when using it (paranoia possibly)
So I can only assume something has given within the screen. Ive been searching all day on the internet for causes and fixes but nothing has come up.
The volume and power buttons work but I cant do anything at all with the phone as its obviously all touch based.
Is this a screen replacement job then or is the whole phone goosed?
Roheelshah if you turn your phone off do you have the massive oily screen thing?
Any help is most appreciated....
Click to expand...
Click to collapse
download and install this _HTC Touch HD_TouchHD system.exe
BOLDESH said:
download and install this _HTC Touch HD_TouchHD system.exe
Click to expand...
Click to collapse
whats it do? and where from??
I just posted something like this a few days ago, pulled my phone out and screen wouldnt respond, had these marks all over my screen, "swirly marks" as i describe it, very well could be the oily marks you are talking about. you can move them around with your finger right?
anyway, i took my sim out, tryna find a spare phone, couple hours later the marks were gone and screen started working again, touch wood its been fine since.
no idea what happened, but try letting it air out or something
ok basically i received a new digitizer today (the actual touchscreen) ...
i dismantled the whole phone using the service manual and some video some guy made (VERY HELPFUL, if anyone wants it for any reason i can post a link), ok so i got rid of all the top bits, the circuit boards (or watever theyre called)
I got down to just the bezel, lcd and digitizer (dont know what a bezel is, the lcd is where the display actually is and digitizer is directly stuck ontop of that)
Apparently when replacing the screen, htc have made it so that you have to replace all three of those parts instead of individual ones, but you can buy them seperately so i thought i'd hero it.
i poked out the screen from the frame (some chewingum like stuff holding it in) then i started peeling off the digitizer (if you get one and want to try it you'll know where to peel) ... this was a mistake tho cause the lcd is unbelievebly sensitive so while peeling off it left scratches on the lcd, and me not knowing the lcd is sticky tried to wipe them and use a dust free cloth, which left alot of crap on the actual lcd!
i managed to get the digitizer off and ripped the cable that goes from digitizer to whatever reads our fingers on the screen, took it all off, placed the new one directly ontop and fed the wire exactly how it was for the first screen.
Put it all together again
Now I did mess up my screen badly, but in a good way! .. i now have full touchscreen working (smoother than ever) but my LCD display is near enough gone, so it looks like the screens really really dark, and i have to tilt it at certain angles to see the screen..
After all of this i now have a touch hd i can controll from my pc (using mymobiler) so i can recieve calls, send texts all from my pc when connected thru active sync, can even play teeter ... but not really the same!
I wouldnt recomend anyone to try what i did, although i think its worth the risk as I would have to replace the lcd anyways if i wanted a new screen in the first place... and who knows you might be able to peel the digitizer off clean (NEVER EVER EVER TOUCH LCD WITH ANYTHING!!!).
It all cost me around 10-15£ for the digitizer and screwdrivers and alot of hours dismantling phone compared to 50-100£ for a new lcd.
I am either going to get a new lcd now so i can actually see the screen, or get a new phone.
Sorry for the essay but hopefully this helps someone in any similar situation
if i do get a new lcd will post how it goes and if it sorts out everything
if anyone knows of any other reasons why my lcd would be so dim (brightness is 100%) accept for me getting carried away with it ... help would be appreciated
the_cool said:
I just posted something like this a few days ago, pulled my phone out and screen wouldnt respond, had these marks all over my screen, "swirly marks" as i describe it, very well could be the oily marks you are talking about. you can move them around with your finger right?
anyway, i took my sim out, tryna find a spare phone, couple hours later the marks were gone and screen started working again, touch wood its been fine since.
no idea what happened, but try letting it air out or something
Click to expand...
Click to collapse
Yeah swirly oil marks is how myne started ... i think i finished off the screen by trying to press hard on the mark to try and clear it .. . so be careful with it.. but think that overall the screen had seen better days (course only a few weeks after warrenty finishes) ... all conections inside were ok aswell
doczyus said:
Dear All,
I have similar problem. Usuallí I use on my HD NRG ROM. About 3 weeks ago I updated to the latest NRG WM 6.5 23xxx ROM with Sense 2.5 Maxmanila version, and since this upgrade the touch screen position moving randomized up or down from 2 mm to 30mm!!! After this ROM I tryed updating each newer version, but not changed nothing. I need realign the screen about 10 times / day!!! The phone I never dropped or cracked.
Can help me somebody what happened with my HD?
Click to expand...
Click to collapse
Same here. Touch screen not working. Phone never flashed, droped,...
Any solution?
unfortunately, a friend of mine changed the touchscreen without success. Phone was in perfect state, no drop, no flash. Just the touch not responding. I'm not sure that changing whole part lcd+digitizer solve the problem.
Hi all!
I've got similar problem with my touch HD. It's stock since I bought it. My touch sense was acting weird, like it wasn't properly calibrated. Like, when I press 7 on phone pad, the phone actually presses 1, and if I press 0, phone presses 5 and so on..
I've tried to align the screen, but it doesn't get aligned the first time. I have to repeat the process about 4 times before it gets aligned. That's good for about few minutes and the problem is back. Hard reset was also done, 2 times.
Could this be a fixed with a software update? Does this mean that digitizer will soon be dead?
Thank you for your help
Regards
igothtc2 said:
Hi all!
I've got similar problem with my touch HD. It's stock since I bought it. My touch sense was acting weird, like it wasn't properly calibrated. Like, when I press 7 on phone pad, the phone actually presses 1, and if I press 0, phone presses 5 and so on..
I've tried to align the screen, but it doesn't get aligned the first time. I have to repeat the process about 4 times before it gets aligned. That's good for about few minutes and the problem is back. Hard reset was also done, 2 times.
Could this be a fixed with a software update? Does this mean that digitizer will soon be dead?
Thank you for your help
Regards
Click to expand...
Click to collapse
use ScreenCal to fix it, hopefully it can help you
Hakim Rahman said:
use ScreenCal to fix it, hopefully it can help you
Click to expand...
Click to collapse
Hi!
I've successfuly installed the cab file on my phone's sd card, but the problem is still there. I don't know where the installed files are, do I have to run this application?
Thank you for your help!
Regards
igothtc2 said:
Hi!
I've successfuly installed the cab file on my phone's sd card, but the problem is still there. I don't know where the installed files are, do I have to run this application?
Thank you for your help!
Regards
Click to expand...
Click to collapse
have you hard reset the device after installing the cab file ?? if not do it and see if there are changes...
Hakim Rahman said:
have you hard reset the device after installing the cab file ?? if not do it and see if there are changes...
Click to expand...
Click to collapse
Just did the hard reset. When it asked me to align the screen, I just couldn't align the top left corner. I had to press it like 50 times before cross went to the lower corner. Otherwise, after the align it's good for about couple of seconds and then it's just pressing all over.
I thought I had just some software issues because the screen wasn't dead, it responded to my touch. So, I'll probably have to buy a new screen and digitizer, right? Or do you have any other ideas?
Thank you again for your help!
Regards
firstly screencal installs calibration settings not for blackstone so do not install it, no point. (btw it also increases device touch sensitivity)
secondly you guys should try and install the calibration settings for blackstone, basicly what the align screen does, not sure where to find them for download but i could post the registrys if someone wants to make a .cab from them. (atm i cba making the .cab but i am able to do it )
if the calibration settings do not work i think it is best to buy a new lcd package (or buy new device and give me old one for spares oj)
Rn
hi buddy ! What you mean GSensorCalibrator ??
i didnt mention anything about gsensor calibration dude.
tried and tested screencal the other week and it screwed my blackstone.
install these instead:
*screen calibration, sets the blackstone touch points: (aligning the screen)
if you install a cab with these registrys it should fix the alignment problem.
(if it doesnt then its hardware issue = lcd etc)
[HKEY_LOCAL_MACHINE\HARDWARE\DEVICEMAP\TOUCH]
"MaxCalError"=dword:8
"CalibrationData"="511,542 183,881 183,198 834,197 833,880"
*this one will maximise the touch sensitivity for those that want it:
[HKEY_LOCAL_MACHINE\Drivers\TouchPanel]
"PressureThreshold"=dword:0
Rn
Does anyone have a recommendation where you can buy a digitizer and lcd from?
Hello Gents and Gals. I am trying to fix my friends HD2, I flashed his ROM with Energy couple of months ago and all was working fine. He gave the phone back to me saying that it is locked.
I tried unlocking the phone but it seems that the screen is unresponsive, so I flashed it again by going into the boot loader screen "Volume Up + Power Button". The phone stated that it is starting for the first time but the screen was still unresponsive. Any ideas on how to fix this issue? Or do I need to tell him to send the phone back to HTC for repairs?
Sounds like the touch screen died ....
Time for a repair ..
Also this really should have been posted in general , as it is not a ROM release , just an FYI
Aww okay. I'll let him know. Thanks.
I'll post like this in General next time. Tks.
HI, I have now the same problem after ROM Flashed, did you solve the problem by yourself, or really the touch screen died.
Rgds
Same thing with me. I ordered new digitizer+LCD and changed them, but the screen is still unresponsive. Other ROM didn't help.
Some advices?
i seen this happen with several phones, reflash to stock and send to HTC they will repair it for free.
I have same problem,yet my phone was bought 18 months ago...worked perfectly until now.
Can a touch screen get defective after normal usage ?
alexandruvlad said:
I have same problem,yet my phone was bought 18 months ago...worked perfectly until now.
Can a touch screen get defective after normal usage ?
Click to expand...
Click to collapse
Yes it can, if your touch functionality of your HD2 has stopped working then your digitizer has probably went out.
T-Macgnolia said:
Yes it can, if your touch functionality of your HD2 has stopped working then your digitizer has probably went out.
Click to expand...
Click to collapse
Yeah,that's what i thought too - but i read some situations where replaced LCD + Digitizers didn't solve this problem.....
alexandruvlad said:
Yeah,that's what i thought too - but i read some situations where replaced LCD + Digitizers didn't solve this problem.....
Click to expand...
Click to collapse
This is usually due to the replacement components not being properly installed. Also when one is working with the internals they have to be very careful as some of the internals are very easy to break without you even knowing you did. So the cases you spec of are more than likely not because it was not the Digitizer or LCD was not the problem, but human error.
i fixed mine and it didnt cost me
the unresponsive screen maybe the digitizer buts its more likey the end call button, believe it or not dirt can get behind the contact or because the back button is next to we use the far edge of the end call button thus leading to bending the contact, when any of this happens your screen will be unresponsive
you can either take it to a shop and pay for a new screen and digitizer or take it apart and clean the contacts
go to ifixit for step by step guides
hope that helps
Intrigued
dgr1983 said:
... buts its more likey the end call button, believe it or not dirt can get behind the contact or because the back button is next to we use the far edge of the end call button thus leading to bending the contact, when any of this happens your screen will be unresponsive
Click to expand...
Click to collapse
I have no idea what are you talking about, that doesn't make sense, as far as I know is no direct relation between END button and (non-working/responding) touchscreen: you may even disconnect/replace bottom buttons ribbon/flex from motherboard and touchscreen will work if OK(or not, if defective).
Is there anybody who can confirm this(or not)?
3 weeks ago I had a LCD/digitizer replaced (cracked screen, but was still working) all was great till 2 days ago. Screen stopped working - took it back to the place I had replace the screen and they tried 3 brand new screens and still no go. Ended up being my main board - luckily I had a spare HD2 and they pulled that board and all is well again.
Believe it or not your LCD/digitizer might be fine - find someone or a way to test main board would be where I would start after the last 3 days.
Good luck
PS - I did NOT try the end button idea prior to the repair.
Zergalot
zergalot said:
3 weeks ago I had a LCD/digitizer replaced (cracked screen, but was still working) all was great till 2 days ago. Screen stopped working - took it back to the place I had replace the screen and they tried 3 brand new screens and still no go. Ended up being my main board - luckily I had a spare HD2 and they pulled that board and all is well again.
Believe it or not your LCD/digitizer might be fine - find someone or a way to test main board would be where I would start after the last 3 days.
Good luck
PS - I did NOT try the end button idea prior to the repair.
Zergalot
Click to expand...
Click to collapse
If still in your possession, I would be interested to buy the motherboard you just replaced!
PM me if interested!
htc hd2 screen died
I also have a 2009 htc hd2 on which screen does not work.
I'd like to know if it's
- a common problem
- is it possible that it's a software (flashing) issue
- can it be replaced and for how much
martinmartiini said:
I also have a 2009 htc hd2 on which screen does not work.
I'd like to know if it's
- a common problem
- is it possible that it's a software (flashing) issue
- can it be replaced and for how much
Click to expand...
Click to collapse
From my own experience :
1. It's a common issue, there are hundreds of reports in this forum and I read them all because I had the same problem some months ago
2. Probably not. It's generally hardware-related and often the digitizer (touch responsive screen) . Brief explanation : There's a flaw in the design of the HD2, the thin cable wiring the digitizer to the motherboard, is just below the power button. After some extensive use of your powerbutton, it might happen that the power button touches the cable and cause some kind of shortcut in it which makes the digitizer unresponsive to the motherboard.
3. I replaced mine here : http://www.htcphonerepairs.co.uk/ . Fast repair, secure shipping to Belgium, good price and excellent customer support. (Sounds like advertizing but I swear to be only a happy customer )
There are also multiple videos on youtube explaining how replacing the digitizer yourself if you dare !
Also, I read answers saying that you can somewhat "play" with your buttons (especially the power one) to turnaround the problem. That's correct, BUT it's absolutely inevitable that the problem with come back again if you use the buttons, and you'll have to force more and more to unblock again and repeat again and a again... and that will damage your button bar.
I did this during almost 2 months and that put down all my buttons and now they are really close to the chassis which is very annoying. If only I knew it before I would have replaced the digitizer directly !
For 6 months with my new digitizer + using ICS with soft buttons, I have no problem at all !
bib*oops said:
I have no idea what are you talking about, that doesn't make sense, as far as I know is no direct relation between END button and (non-working/responding) touchscreen: you may even disconnect/replace bottom buttons ribbon/flex from motherboard and touchscreen will work if OK(or not, if defective).
Is there anybody who can confirm this(or not)?
Click to expand...
Click to collapse
Just because this dude has "no idea" it doesn't mean he knows it better.
It IS the END button that gets pressed too often and at some point it begins to mess with the digitizer connection. It can be dirt. It can just be the cable came lose and needs tightening, it can be wear-out.
whatever it is, it is caused by the end-key being too close to the connector cable.
If you guys only searched for this on the HD2 Forums before posting this Thread hat not been necessary. It is the most well known design flaw of the HD2 and as such well documented and commented here.
Sneakyghost said:
Just because this dude has "no idea" it doesn't mean he knows it better.
It IS the END button that gets pressed too often and at some point it begins to mess with the digitizer connection. It can be dirt. It can just be the cable came lose and needs tightening, it can be wear-out.
whatever it is, it is caused by the end-key being too close to the connector cable.
If you guys only searched for this on the HD2 Forums before posting this Thread hat not been necessary. It is the most well known design flaw of the HD2 and as such well documented and commented here.
Click to expand...
Click to collapse
This is truth. Save yourself some time and frustration and repair it or get it repaired. It's a great phone.
Sneakyghost said:
Just because this dude has "no idea" it doesn't mean he knows it better.
It IS the END button that gets pressed too often and at some point it begins to mess with the digitizer connection. It can be dirt. It can just be the cable came lose and needs tightening, it can be wear-out.
whatever it is, it is caused by the end-key being too close to the connector cable.
If you guys only searched for this on the HD2 Forums before posting this Thread hat not been necessary. It is the most well known design flaw of the HD2 and as such well documented and commented here.
Click to expand...
Click to collapse
You didn't get it right or at all:
END key may determine touchscreen failure along the time(being the CAUSE! of this), but the EFFECT is an unusable touchscreen, which cannot be repaired in any other way than replacing it(the touchscreen!!, I mean).
Any other attempt to repair, clean, bend, press, cut or whatever WILL NOT FIX an already faulty touchscreen (even caused by END button excessive or not usage) and who thinks otherwise, no problem with me: SWEET DREAMS!
You sound like my comment hurt you. Sorry if it did. I'm not one hundred percent sure that this issue can be fixed without replacing the screen, yet fairly certain. I've now disassembled two HD2 and couldn't quite find the precise spot where the damage occurred, yet after properly assembling the devices again, one came back alive, the other not. The one which has the screen and buttons not working right is the one that got thrown at me by a kind person. It most likely has physical damage somewhere, although I couldn't locate it. The other one didn't get damage and has screen and buttons work well after complete disassembly and assembly.
Both devices also have different screen types.
I now gave up both devices and am withdrawing myself from the HD2 world. Too many issues with the devices getting old.
sent from the tip of my finger
So I'm having a strange problem that is driving me insane! This past weekend the menu and back buttons on my MT3G started working intermittently, and at one point I saw the back light for all of the hard buttons flickering. After a few days of it coming and going they went out all together. The next day the trackball button quit working too. That sucked but I figured I could just use the power button to wake the phone until I figured out my problem. Then the best part happened, the touchscreen quit responding completely! Since I got off work this morning at 7 I have had it completely apart 3 times, checking and rechecking all connections, and have gotten nowhere! I was thinking the digitizer was bad (that I had to replace a few months back but have had no problems since then) but that doesn't explain the other buttons. Anyone have any ideas for me?? Should I try a new digitizer? Something bad with the board? I have no idea what else to try and I'm exhausted so I'm going to bed, I apologize if any of this doesn't make since as I'm basically sleeping on my feet and am extremely frustrated!! Thank you for taking the time to read this and any help will be greatly appreciated!
This may be late but...
The most likely problem is the motherboard flex cable. This exact thing happen to me over the past week and now neither my front buttons or my ir trackpad work. And they all stopped working at different. Open up your phone (find instructions on youtube) and take a look at your flex cable. When I saw mine, it looked like it had been cut half a centimeter through 3 bridges. Don't buy a new digitizer before looking at the flex cable. Hope this solves your problem, even though its almost a year late lol. But at least anyone who still has the phone (like me) can use this info.
flex cable issue i think
The touchscreen, center button, and back and genus buttons stopped working for me. The back and genus buttons also fail the key test in recovery. Is the general assumption that if the buttons are also acting up, its more likely the flex cable and not the digitizer?
Does it matter if I get an OEM or 3rd party flex cable?
Thanks.
Hey y'all,
I am having a weird problem. I have an HD2 wich worked great. Now after some time I am having a problem with the phone waking up. When it's active and unlocked, the touchscreeen works great, but when I turn off the screen and turn it back on, it won't let me unlock it. The touch screen just doesn't seem to work any more.
So I thought maybe relfashing could help. Said and done - reflashed Android > didn't work. Wiped, flashed WP7 > didn't work.
After some time and trying 3457 times, it works sometimes and once it is unlocked everything works well. But it's unusable this way.
Any ideas?
Thanks in advance,
JR
I had this problem yesterday. I bought my phone second hand, it had a brandnew touchscreen, the previous owner dropped it.
after 3 months (yesterday) it started woring really bad. 8/10 times it wouldnt work.
I got my hands on a HD2 which was bricked (epic fail) for 10 bucks and swapped my mainboard. it works flawlessy again. Im guessing the replaced digitizer was a cheap knockoff from China.
Sent from my HTC HD2 using XDA App
JROppenheimer said:
Hey y'all,
I am having a weird problem. I have an HD2 wich worked great. Now after some time I am having a problem with the phone waking up. When it's active and unlocked, the touchscreeen works great, but when I turn off the screen and turn it back on, it won't let me unlock it. The touch screen just doesn't seem to work any more.
So I thought maybe relfashing could help. Said and done - reflashed Android > didn't work. Wiped, flashed WP7 > didn't work.
After some time and trying 3457 times, it works sometimes and once it is unlocked everything works well. But it's unusable this way.
Any ideas?
Thanks in advance,
JR
Click to expand...
Click to collapse
My friend's phone has the same issue. Touchscreen works if you wake up the phone by back button, but it does not if you wake up with power button. Did you try that?
The most strange thing is, it is the same when on windows or android, as you said.
Klael said:
My friend's phone has the same issue. Touchscreen works if you wake up the phone by back button, but it does not if you wake up with power button. Did you try that?
The most strange thing is, it is the same when on windows or android, as you said.
Click to expand...
Click to collapse
Hey there.
After some searching I found out, that the digitizer is messed up. The thricky thing is: The digitizer hardware is located right beneath the power button. This is what is causing the problem (the power button was messed up a little also). So if you are experiencing the same issue - try pushing the power button a little harder. That might make you able to wake up the phone.
I would have to renew the digitizer, wich is a real pain and a lot of work. You'll get a new HD2 for around 130€ and the digitizer costs about 60€ I guess. Plus all the work and the risk of f***king it.
SO - my choice will be a new one. HD2 is just a great phone because of it's community!
or get a bricked on for less like I did. Swapping the mainboard is really easy if you take the time and use the iFixit repair guide. I used a hair dryer to ease up the internals by heating it up and with a suctioncup I pulled the internals right out of the shell.
the copper sticker is a real pain in the ass though... But its doable.
You'll need a T5 torx screwdriver.
Oh and I love the HD2 community no doubt about it
Sent from my HTC HD2 using XDA
I have the same problem, you think it gets resolved by buying a new digitizer? I was told the problem is not that main board but only the digitizer so not worth the hassle of getting a bricked phone I assume.
Thanks
kenterr001 said:
I have the same problem, you think it gets resolved by buying a new digitizer? I was told the problem is not that main board but only the digitizer so not worth the hassle of getting a bricked phone I assume.
Click to expand...
Click to collapse
A nonresponding digitizer can be caused by many things. I´ve heard of the end key messing with the touchscreen controller and vice versa.
I had a replacement digitizer on my HD2, it stopped working and now I have a genuine digitizer.
The genuine screen is just much much much better. It just feels much better. It´s more ´slick´. And less grime attracting.
Look in the general section for people who have bricked their HD2 and PM them and offer them money
Hey guys i have the same problem u think its the digitizer not the flexible ribbon?
now when i press any button nothing happen its like the screen become unresponsive and after hours of trying it unlocks
if you sure 100% of what causes the problem please tell me so i can get the parts
100 %
SnakeBites said:
Hey guys i have the same problem u think its the digitizer not the flexible ribbon?
now when i press any button nothing happen its like the screen become unresponsive and after hours of trying it unlocks
if you sure 100% of what causes the problem please tell me so i can get the parts
Click to expand...
Click to collapse
Buy yourself an appropriate touchscreen!
Hi guys! Some weeks ago I dropped my phone and my whole screen cracked, so, I bought a new one and wanted to repair it myself to save some money, you know ^^.
But anyways I put everything back on, but my screen just won´t start. Well it is turning into a dark blue so I guess it actually works.... a bit. But everything else works just fine, if someone calls me I can easly just pick it up and talk, I just have to figure out where the Buttons are . It reacts to touch so I guess it´s only the digitizer... Please Help
Maybe some ports aren't connected well? Or the display was broken? Try contacting the seller