Touch screen, menu button and back button not working - myTouch 3G Slide General

So I'm having a strange problem that is driving me insane! This past weekend the menu and back buttons on my MT3G started working intermittently, and at one point I saw the back light for all of the hard buttons flickering. After a few days of it coming and going they went out all together. The next day the trackball button quit working too. That sucked but I figured I could just use the power button to wake the phone until I figured out my problem. Then the best part happened, the touchscreen quit responding completely! Since I got off work this morning at 7 I have had it completely apart 3 times, checking and rechecking all connections, and have gotten nowhere! I was thinking the digitizer was bad (that I had to replace a few months back but have had no problems since then) but that doesn't explain the other buttons. Anyone have any ideas for me?? Should I try a new digitizer? Something bad with the board? I have no idea what else to try and I'm exhausted so I'm going to bed, I apologize if any of this doesn't make since as I'm basically sleeping on my feet and am extremely frustrated!! Thank you for taking the time to read this and any help will be greatly appreciated!

This may be late but...
The most likely problem is the motherboard flex cable. This exact thing happen to me over the past week and now neither my front buttons or my ir trackpad work. And they all stopped working at different. Open up your phone (find instructions on youtube) and take a look at your flex cable. When I saw mine, it looked like it had been cut half a centimeter through 3 bridges. Don't buy a new digitizer before looking at the flex cable. Hope this solves your problem, even though its almost a year late lol. But at least anyone who still has the phone (like me) can use this info.

flex cable issue i think

The touchscreen, center button, and back and genus buttons stopped working for me. The back and genus buttons also fail the key test in recovery. Is the general assumption that if the buttons are also acting up, its more likely the flex cable and not the digitizer?
Does it matter if I get an OEM or 3rd party flex cable?
Thanks.

Related

Crazy Tytn screen and button problem, please help

Hi all, this is my first post on this forum but I've been reading for a while to educate myself.
I've got a Herm200 that I've been trying to troubleshoot but to no avail. I'm fairly certain that it has a hardware problem but I haven't been able to isolate anything.
Here's whats happening:
Occasionally the screen will come out of stand-by all white. This will also happen randomly if i touch the screen to perform a command. While the screen is operating, sometimes the buttons on the face will stop working, however the buttons across both sides will continue working just fine.
When the screen turns all white a soft, hard, or stand-by cycle will not always bring it back to life. The fact that the hard reset wont always fix the problem makes me think it's a hardware issue since the phone will boot-up with the the all-white screen.
This is incredibly frustrating especially since HTC wont accept any warranty claims in the USA on the Tytn.
At first I thought this might be a problem with the ribon connection between the screen and the base but i haven't been able to confirm or discount anything at this point. I have yet to find a way to consistently reproduce or rectify the problem so it's very hard to troubleshoot.
I pretty much have to take a second phone with me everywhere right now just incase i need to make a call. Please help! Has anyone ever encountered such a problem?
Thank you in advance!
SneezyRobot said:
Occasionally the screen will come out of stand-by all white. This will also happen randomly if i touch the screen to perform a command. While the screen is operating, sometimes the buttons on the face will stop working, however the buttons across both sides will continue working just fine.
Click to expand...
Click to collapse
Hi. This sounds very similar to a problem that I experienced with a HERMES100. I bought the phone off someone on Ebay recently - someone had obviously scrambled the radio on it. I re-flashed it, and it sprang to life. However, after a couple of days, I experienced a problem where occasionally the LCD would stop refreshing, all the pixels faded away leaving only a white screen. Under these circumstances, some of the buttons on the phone stopped working. Turning phone on/off sometimes cured the problem, or it would require the occasional hard reset. This would happen once or twice a day and I suspect thats why someone tried to re-flash the phone.
In the end, out of curiosity I took the entire phone apart, put it all back together again and now there are no more problems!! Totally fixed!
My suspicion is that it was one of the ribbon cable push connectors on the mainboard - possibly not seated properly, or a bit of dirt contaminating the connection. Obviously when I took the phone apart I must have re-seated it.
If you are planning to take your phone apart, please exercise considerable care because some of the parts are very small and easily damaged. I would recommend buying a proper kit to take it apart. I bought mine for about £5 off ebay. Particularly useful are the plastic spoon "wedges" used to gently prise open the case after removing the screens. Don't use a screwdriver - you will scratch the case.
Good luck.
wow... that sounds like exactly what's going on here, I actually even tried to disassemble it lastnight but didnt have the right driver set. thank you for the advice!
I'll look for one of those sets but what would you search for if i needed to find it?
Thanks again, I just got a set off of Ebay. Hopefully it'll be here next week
With any luck it'll be a connection issue.
I have had the exact same problem. Because I got the Tytn through work I made our IT department handle the issue and I am currently waiting for a replacement and to find out what happened.
Yep, it looks like the problems the OP is having are very similar to the problems we've been having over in this thread:
http://forum.xda-developers.com/showthread.php?t=291027
I'm beginning to think it's a hardware problem as well but not entirely sure.
People in the above thread mentioned that using the scroll wheel a while then moving back to use the D pad fixed the problem (very briefly in my case.) Once I use the center D pad button again it locks the hardware buttons under the screen until I make my device sleep and resume.
Somtimes rather than making all the front hardware buttons unresponsive the issue is that once I use the Down Dpad button I can't use the up button. Pressing up will make it go down, as will pressing down (at least that's working ).
Regarding the white screen - this sometimes also occurs. I can force it to white screen by putting a little pressure on the silver panel surrounding the top, right and bottom of the screen (I have an imate jasjam). Randomly when there's no pressure on the rim and I wake it out of standby, it has a white screen that can only be fixed by turning the screen off and on again.
Finally, the LED indicator seems screwy. Sometimes it never flashes. Other times it flashes sporadically (uneven intervals - we're talking maybe a minute between one flash then seconds before another). When I charge it sometimes the LED doesn't come on but nevertheless it charges. Sometimes if the LED is on it never turns green to indicate a full charge. Yet other times it comes on orange, turns green, then never switches off!
Is it possible that
a) The hardware button problems.
b) The white screen problem.
c) The LED problem.
are all related to some kind of connection going loose? Why would the hardware button problem be temporarily fixable with use of the scroll wheel if this were the case?
The other thread has fallen silent. I'm hoping that some of the gurus in here can offer some input here, even if they don't know the answer but can formulate an opinion. I know very little about these devices.
Thanks in advance guys!
PS - don't really know if I should start another thread, I've posted here as it seems like very much the same issue.
Anybody any idea? advice?
I had a similar problem with my HERM100. I didn't mess around with it too much, I just had Cingular replace it out of warranty exchange (thank god those original ROMs are on the wiki ). I did notice however that after doing a master reset, the screen would function again although I haven't messed around with it too much. I got so frustrated with removing the battery for 5 minutes and STILL powering on with a white screen that I just threw it in my back seat until the new one arrived.
I don't have these screen issues. I only have hardware button problems. It's so damn frustrating! I already own a replacement.
I just received a call from my girlfriend. I wasn't able to answer the phone with the buttons, only with a screentap. I also wasn't able to close the call with the hardware button. Since the side buttons work, I went to settings -> phone, closed it, and there we go. The hardware buttons worked again.
Why the heck is this? I truly hope for some wizz out there with some advice, since HTC would only tell me to send it back after replacing it with a new TyTN with same issues.
Regards,
DM.
Anyone anyone?
HELP!!!!
barncourt said:
Hi. This sounds very similar to a problem that I experienced with a HERMES100. I bought the phone off someone on Ebay recently - someone had obviously scrambled the radio on it. I re-flashed it, and it sprang to life. However, after a couple of days, I experienced a problem where occasionally the LCD would stop refreshing, all the pixels faded away leaving only a white screen. Under these circumstances, some of the buttons on the phone stopped working. Turning phone on/off sometimes cured the problem, or it would require the occasional hard reset. This would happen once or twice a day and I suspect thats why someone tried to re-flash the phone.
In the end, out of curiosity I took the entire phone apart, put it all back together again and now there are no more problems!! Totally fixed!
My suspicion is that it was one of the ribbon cable push connectors on the mainboard - possibly not seated properly, or a bit of dirt contaminating the connection. Obviously when I took the phone apart I must have re-seated it.
If you are planning to take your phone apart, please exercise considerable care because some of the parts are very small and easily damaged. I would recommend buying a proper kit to take it apart. I bought mine for about £5 off ebay. Particularly useful are the plastic spoon "wedges" used to gently prise open the case after removing the screens. Don't use a screwdriver - you will scratch the case.
Good luck.
Click to expand...
Click to collapse
This is my first post as I've so far managed to cure all my issues from just reading the forum. However, I am now having a similar problem with the white screen.
I have a cingular 8525. It fell and the following day the call and end buttons remained lit and wouldn't turn off and they also wouldn't work.
I soft reset, nothing, I then removed the battery and when I turned it back on, there was a white screen and the buttons below still don't work.
I have read the other posts on this issue, but I need help on exactly what kit to buy to reconnect the screen cable and instructions on how to do it as I've never taken apart a phone before, although I have dabbled with other electronic devices.
Your help would be much appreciated, as I am in Jamaica and there are no technicians here who I trust to help.
Thanks in advance.
Below are links to 2 kits I'm thinking of getting. Is either one better than the other?
http://www.pdasmart.com/pdaphonehtcmini.htm?gclid=CJrHntO-hosCFQx1VAodaQf6KQ
http://cgi.ebay.com/SCREWDRIVERS-TO...01677255QQcategoryZ108648QQrdZ1QQcmdZViewItem
CINGULAR IN JA said:
This is my first post as I've so far managed to cure all my issues from just reading the forum. However, I am now having a similar problem with the white screen.
I have a cingular 8525. It fell and the following day the call and end buttons remained lit and wouldn't turn off and they also wouldn't work.
I soft reset, nothing, I then removed the battery and when I turned it back on, there was a white screen and the buttons below still don't work.
I have read the other posts on this issue, but I need help on exactly what kit to buy to reconnect the screen cable and instructions on how to do it as I've never taken apart a phone before, although I have dabbled with other electronic devices.
Your help would be much appreciated, as I am in Jamaica and there are no technicians here who I trust to help.
Thanks in advance.
Below are links to 2 kits I'm thinking of getting. Is either one better than the other?
http://www.pdasmart.com/pdaphonehtcmini.htm?gclid=CJrHntO-hosCFQx1VAodaQf6KQ
http://cgi.ebay.com/SCREWDRIVERS-TO...01677255QQcategoryZ108648QQrdZ1QQcmdZViewItem
Click to expand...
Click to collapse
Both kits look ok. PDA one tells you a little more but the basics appear to be in both.
I'm curious though you soft reset and took the battery out, but have you done a HARD reset? I would always try this first before dismantling.
Mike
In my case, they also are always lit up when the screen is also active.
And no matter what ROM version, they occasionally stop responding. Side buttons keep working.
mikechannon said:
Both kits look ok. PDA one tells you a little more but the basics appear to be in both.
I'm curious though you soft reset and took the battery out, but have you done a HARD reset? I would always try this first before dismantling.
Mike
Click to expand...
Click to collapse
Thanks for the response.
I couldn't do a hard reset because the buttons weren't working.
I have made some progress with the phone now. Found a tech guy who looked at it for me. The white screen is gone, but the buttons still stop working from time to time.
All the connections seem ok.
Is there anything else that could cause the buttons to malfunction?
CINGULAR IN JA said:
Thanks for the response.
I couldn't do a hard reset because the buttons weren't working.
I have made some progress with the phone now. Found a tech guy who looked at it for me. The white screen is gone, but the buttons still stop working from time to time.
All the connections seem ok.
Is there anything else that could cause the buttons to malfunction?
Click to expand...
Click to collapse
Nothing obvious.
Have you got applications installed that you have loaded - could be one thats playing up.
Have you now been able to do a hard reset?
If taking device apart and reassembling improved things it does suggest hardware though and might be worth double checking all those multi-connector blocks for good connections - i.e. take them out and in a few times to ensure any oxidation on contacts is removed.
Mike
mikechannon said:
Nothing obvious.
Have you got applications installed that you have loaded - could be one thats playing up.
Have you now been able to do a hard reset?
If taking device apart and reassembling improved things it does suggest hardware though and might be worth double checking all those multi-connector blocks for good connections - i.e. take them out and in a few times to ensure any oxidation on contacts is removed.
Mike
Click to expand...
Click to collapse
Thanks Mike.
I will give that a shot.
I haven't installed any new applications recently, so I don't think it is a software issue.
Thanks again.
CINGULAR IN JA said:
Thanks Mike.
I will give that a shot.
I haven't installed any new applications recently, so I don't think it is a software issue.
Thanks again.
Click to expand...
Click to collapse
If it wouldn't be a software issue, why is it, in my case, instantly resolved when going to settings -> phone with the side buttons?
i had this problem i took it to a guy who fixed the problem he said it was a very small tear in the flex cable which causes this white screen every now ant then and the buton problem , sorry to say its the cable problem and u need a very capable person to fix it or replace it with a new one . its very common problem baised on the guy who fixed it .
dmxl said:
I don't have these screen issues. I only have hardware button problems. It's so damn frustrating! I already own a replacement.
I just received a call from my girlfriend. I wasn't able to answer the phone with the buttons, only with a screentap. I also wasn't able to close the call with the hardware button. Since the side buttons work, I went to settings -> phone, closed it, and there we go. The hardware buttons worked again.
Why the heck is this? I truly hope for some wizz out there with some advice, since HTC would only tell me to send it back after replacing it with a new TyTN with same issues.
Regards,
DM.
Click to expand...
Click to collapse
Exactly what is happening to me, no white screen issues, just screen taps and answering calls, I also have another problem where the PDA will not allow me to open anything, be it the start menu or contacts, it will open and quickly close again. I have had mine swapped through Telstra in Sydney, it worked fine for a while and then the same crap again. These problems started before I even touched the OS, so it must be a build problem. Maybe we should write a joint letter to HTC letting them know that there is a serious problem with their machine.
I have had the same problem, got my Tytn through work so we sent it back to the company that supplied it to us. Got it back yesterday and they had replaced the "switchboard". Not sure what it is but there was the problem. Had white screen and buttons not working.

8525 White Screen of Death - Is there Hope?

Ok so I have the fabled white screen issue on an 8525. When it first occurred I searched and read all the write ups, decided I had the ribbon cable issue. Took it apart and simply unplugged and replugged the ribbon cable with great results, no more white screen.
I repeated once when it came back after being bumped around, again with positive results...but this last(3rd)time instead of it working I now get white screen 95% of the time. I re-notched the sliders the first time, and last time.
During the 5% it works I noticed the charge light would correspond to it going white.This never happened before...
Example:
When OFF - Connect charger, Red light for 1 second, then nothing=White screen from power on
When OFF - Connect charger, Red light for 1 second, then orange charge indicator = normal startup
When ON and Working - Connect charger, no light, no charge - reboots to white screen
When ON and Working - Connect charger, orange charge indicator, reboots normally.
There is no heat or noticeable pressure on any parts, everything seems to fit normally.
It does boot normally with screen white.
Any ideas? I really don't want to give up on this thing, is there any hope? or just ebay it for parts?
Thanks
-Nick
same problems here, if someone could just tell me what parts to order, cause I have no warranty (ordered over ebay). I tried both the instruction that has chinese fonts on the page , and other from R&R, no luck, white screen all the way..
I had the WSOD and took it apart and reassembled a few time. The 3rd or 4th time the screem came back, but now it is shifter to the right around 1/4" or so. I mean there is just white along the left edge, then the normal screen/color starts and is cut off on the right.
Does anyone know how to correct that, is it related to the same flex cable or is there something else I disturbed?
mine will fade to white.. then i just push the power to put it in standby, then push power again to wake it back up and back to normal.. it rarely does it but still annoying...
If You Ordered From At&t
I had this problem about 2 weeks ago!!!!
I thought it was a fluke!
Anyway, walked over to 43rd and Lexington (NYC FOR THOSE WHO DON'T KNOW THAT MANHATTAN IS THE CENTER OF THE WORLD)
and they gave me the EXCHANGE HOTLINE for at&t.
I called them up, told them my screen is fading to WHITE and the lady sent me a new or referbished phone.. i dont even know.
Just so you know, i ordered my phone on AMAZON with a new activation. its covered under the MANUFACTURERS warentee for a full year from the date of purchase... so is the REPLACEMENT PHONE... but not from the date of replacement, just the date of purchase.
did anyone get deeper into this yet? I got a 8500 (need those without camera) from ebay USA, already with white screen. After reading here, that this is mostly an issue with connectors, I bought it, disassembled it and reassembled it, though still white. Should I give the contacts a treatment with contact-spray? (there's a tuner spray that doesn't leave residues) Or is there something broken within the ribbon cables? Seller said it has been dropped (but he also said, he didn't want to open it, while it clearly has been opened, one screw missing and warranty seal gone). It ssems to boot up normal otherwise, I hear a sound after the boot process, so probably this isn't a software issue?
Edit: another thing I noticed: When I run it without any keyboard connected at all, it's also white. I then connected the dpad again, and I could see a hint of the at&t logo in the lower part of the screen. When I pressed around on the back of the dpad a bit, all LEDs would go on/off... Sound to me like the dpad has gone bad, possible?
Edit II: Got it. Using a 20x eyeloupe I found that the PCB of the DPad is broken under the little chip on it. Now I just gotta find a dpad here in germany, but I assume those Hermes' are all equal...
hello
where can I get manual (if there is one) for disassembling hermes. link in wiki does not work.
thanks
this worked good for me
http://inuchanbt.blog54.fc2.com/blog-entry-100.html
Anyone know if this applies to the 8125 as well? I've got a flickering white screen. I had dropped my phone a few weeks back and cracked the LCD. Replaced it with an OEM LCD - it worked fine for about 2 weeks and then just suddenly went all white. Phone still works, I can still get calls - just can't see who is calling.
I don't recall that the wizard had the same problem... Though from a logical point, it seems that there is an issue behind white screens and the thumbpad being responsible for it, so it may well be the same thing. Perhaps just disassemble the wizard (there should be a howto too) and check if theres a similar connection from mainboard to thumbpad circuit.
Is there a disassembling manual for a imate k-jam that anyone knows about?
Here's a website with a video manual i found useful...
http://viralelectronics.com/category/howto/page/2/
Figured out the problem...
The only reason I figured out the screen goes blank is because the motherboard loses connection with the screen when you slide the keyboard out...try this out and see if the screen comes back...
put the screen on sleep mode (no white screen)...then slide out the keyboard and tilt it a little hard after pressing on the screen and put the power on. if it doesnt work try again it might take some pressure and power to make it work...be careful not to put too much power but as far as I went, it's a very sturdy cell.
alternately, slide out the keyboard in sleep mode, and press all the buttons really hard and then try to press the power button (press more towards the space bar because that helps)...if any of this works and the screen comes back on even just for a second...follow the following
Go back to the person who gave the link to the site with opening the HTC instructions and follow through and clean the whole phone up from dirt around the screen and such...you dont need to put those rubber things or whatever it says to put on the screen...then when you are putting it back together, press hard on the wire connecting the touch screen to the motherboard. I suggest sealing it with a good tape...and then you are good to go! I did it but it had a few glitches...the screens contrast sometimes goes awry but it is still visible and responds to touch. Also, the physical buttons work as well!!
Good Luck and do it at your on risk.
Have any of you tried this? http://forum.xda-developers.com/showthread.php?t=321163
hope the best
i tried this and it worked for me. i also pressed alil hard around the d-pad and heard a pop. i think it poped back into place.
thanks
razor rc said:
i tried this and it worked for me. i also pressed alil hard around the d-pad and heard a pop. i think it poped back into place.
thanks
Click to expand...
Click to collapse
i still have this problem.
fixed my wsod
I noticed a few days ago my 8525 screen went white, rebooted and it went away. Today it came back, but would only go away for a few seconds and then back to white. After reading some forums I decided to check the connector. I took the phone apart following this site as a guide. I removed the connector on the board side and cleaned the contacts with a qtip and denatured alcohol. Phone has been perfect for the last few hours, no more white screen of death. I didn't mess with the connector on the LCD side, just the board side. I'm a computer tech and I found it quite annoying to disassemble, but I managed without causing any damage, however, I'd rate the job at about a 8/10 as far as technical ability.
Joey
warped0202 said:
I noticed a few days ago my 8525 screen went white, rebooted and it went away. Today it came back, but would only go away for a few seconds and then back to white. After reading some forums I decided to check the connector. I took the phone apart following this site as a guide. I removed the connector on the board side and cleaned the contacts with a qtip and denatured alcohol. Phone has been perfect for the last few hours, no more white screen of death. I didn't mess with the connector on the LCD side, just the board side. I'm a computer tech and I found it quite annoying to disassemble, but I managed without causing any damage, however, I'd rate the job at about a 8/10 as far as technical ability.
Joey
Click to expand...
Click to collapse
i agree that this is one of the first things to try in curing the white screen issue. Others may find their problem runs a little deeper and the contacts on the d/pad chip are broken. An improvised cure which may not be very permanent is to place a little padding on the surface of the chip as described here:
http://forum.xda-developers.com/showthread.php?t=321163
If you have appropriate heat gun equipment you can re-flow the solder on the d/pad daughter board - but remember to remove the sticky key pad layer or you'll cook it!!
I regret that I'm closing this thread because we have several "White Screen" threads and the questions and answers are being spread all over the place.
Please use this one for future posts:
http://forum.xda-developers.com/showthread.php?t=321163
Mike

What a STRANGE problem with my buttons and LEDs! Ideas?

Hi guys!
Long time no post!
I hope you can help point me in the right direction.
Two things started happening with my 8525 TyTN, rendering it unusable. I do have a backup one, so it's no panic. But I would LOVE to try to repair this.
Here's what happens!
1 - The two LEDs in front don't work! No green; no blue; no amber. (HOWEVER, When I first replaced the battery after a hard reset, I did see is glow red for a second!)
2 - None of the buttons on the front work! None. Start/End, the D-pad, mail, internet explorer. All dead!
Interestingly enough... the LCD screen is perfect, as is the touch screen.
The unit also works perfectly fine.
I did a Hard Reset.
I am using WM6.0.
I am wondering... PERHAPS there is some kind of ZIF cable that goes from the body to the top panel? MAYBE that came loose?
If you have seen inside your TyTN, is there one cable/ribbon for lights/buttons?
If so, that would explain it!
If there are two cables/ribbons.... one for lights, one for buttons, then the odds of them BOTH falling out are near impossible!
I would LOVE to hear any ideas or thoughts!!!
Thanks as always!!!!!
Mike
Hello and welcome to a new phone!
I have a similar problem, mine sometimes gets a white screen and the D-pad buttons rarely work for long.
It is quite possibly a loose ribbon cable.
There is actually a thread here about this issue - just do a search for 'white screen' or similar and you'll find it. It was posted to within the week so shouldn't be far from the top if you browse for it, but I can't remember which Herme's category it was in.
There's even a full guide with pics to pulling your 8525 apart!
Cheers! Oggy. ó¿ó
try a new rom,.
I have the same problem. I thought it was bcs my TyTN fell down once. It started with Iexplorer always popping up when I wanted to do something. I thought the IE button at the top was stuck or something and when I pressed hard on the message button everything was okay. All buttons worked. But after a few days they stopped working and pushing the message button wont work also. And both the red and green call button leds are always shining. It sometimes happens that the dpad works for a second and than nothing.
I used the original wm5 and flashed to 6.1 now, no change tho.
it's not the rom, tried several roms now
for me it's just the call answer button, but this is annoying enough
there are some topics in the hermes section which describe the problems you encounter or even worse problems (the lcd flickering or just giving you a bright shining white) and they all say it is a loose cable connector right under your dpad
some of them opened their tytn (guarante already gone) and put some sort of paper or rubber or sth else on the connector.
other say tighten or loosen the screews worked for them, but none of the solutions seem to be final, it always works for some time.
if you have still guarantee i would try sending back or try somewhere else a repair, that is what i will do with tytn
i hope i do not have to pay for the repair
good luck
Loose screw
I was able to fix this problem after ATT told me that I was out of warrenty and it was going to cost 499.00 for a new phone.
I it turn out it is a loose screw on the inside and to get to it you have to undue 11 screw to get to it. I might be able to fix it for you. I dought you would be able to get into this phone and not hurt any of the other functions.
Rick
Hi,
could you advise how you managed to fix it?
Thanks.
button failure and white screen
I have the same problems, if I turn off and on for 3/4 times everything back to normal. But is really annoying because I miss calls.
To me seems a software issue.... I can solve it by turning off the screen does not make sense hardware problems
have a look to this post:
http://forum.xda-developers.com/showthread.php?t=435281
I have still to test the suggestion of schaps advance config version 2.02.1.0.0
Sorry it not a software issue and you can flash a 100 roms and it still won't work. You simply have a bad flex cable and possibly a defective dpad circuit board. You have to crack open the phone to replace it and it has to be carefully done. There are tons of DIY's about opening the phone and replacing the cable. There are even YouTube Videos about it.

X1 Ribbon cable - what happens and a fix I came up with!

Hi, I come on here quite a lot for information as it's an amazing resource! This time however, I'm attempting to give something back!
I experienced the "black screen on slide out" on Monday. Phone completely screwed. I've also had a few droppages and had it apart once before so there's no way warranty is gonna help!
I stripped it down and soon discovered what it is that actually fails on the ribbon. The coating had worn through due to rubbing on something during the slide out / in process. it had been playing up for a while, probably due to shorting out on the metal case, but now the tracks (aluminium?) had worn right down.....
In pic 1 i've circled the worn area. The shiny section is where i'd tried taping over it to prevent shorting, before i realised the tracks were gone.
Got an almost new one off ebay for 15 quid and, realising it was going to happen again, came up with a solution that, so far, looks like it will work....
A while back I bought some "anti rattle felt" for my car's dashboard - really thin and strong self adhesive felt to prevent squeaking joins between dash sections. I cut a piece of this and stuck it to the new ribbon. Once this stuff is on it's well stuck, by the way!
See pic 2 for the modded ribbon cable.
On reassembly everything is working just fine so far! Here's hoping that it lasts longer than 6 months this time!
Just need a new casing now as mine is decidedly second hand!
Hope this turns out to be of use to someone!
cool story bro
when i took apart my xperia to replace the housing this seemed like a really weak point in the device. glad to see someone who has had the problem has been able to fix it
Why does the screen go black?
Hi,
When the coating wears off the ribbon cable it exposes the tracks in it. when you slide the keyboard out the exposed tracks short out on the metal casing and the screen loses it's input signal.
thats whats happened on mine at least and i presume quite a few others?
HTH!
Update:
That's interesting: My phone was also losing signal with the keyboard out, and occasionally while closed up as well. It would just randomly drop to "no signal" for a few seconds.
It hasn't done it since replacing the ribbon cable.....could be coincidental of course.
I'm having the same problem
It just started a week ago and I got the phone in January off of ebay. I'm new to opening up the phone so could anyone help me find the correct tools or have a link to a site with pictured instructions?
I noticed that the sliding mechanism started to go loose about 4-5 months ago but didn't expect the screen not respond in landscape mode. I have yet to see the other symptoms you all are referring to. I would like to fix this before it get worse.
In mine case it went totaly black after one week of this problem... You have all the instruction on youtube, there is where i looked. For tools you can be inovative, but the exactly right ones come with housings from ebay, it is only 15EUR, and i bet you have some cracks so it wouldn't hurt replacing. That is what i did, along with ordering new sliding mechanizm, and new ribbon cable.
I am open for ideas to prevent my ribbon cable from being cut at it weakest point again.
I'm assuming my flex ribbon went bad yesterday, since sliding the keypad out causes my screen to shut off.
Already ordered a cable off ebay and will attempt to replace it myself :O
Replaced my flex ribbon cable with one I bought on eBay. The screen doesn't turn on at all now, which leads me to believe the cable I was sent is defective. Put the old one back in and it works okay, less landscape mode. ughhh what a pain.
great tips! my input is I bought a case off of ebay that was ~60$ and everything actually fit fine for me...so I wouldn't discount every seller but you do get what you pay for, the 15$ cases are probablly the ones that will give you problems
I working in a mobilephone repair center if anyone need help drop me a priv... i able to get 2nd hand or even brand new components
Replaced the flex ribbon cable -
I got my flex ribbon cable a few weeks ago and took it to my local repair shop. They replaced it but the LCD screen/optical joystick receives no power. The touchscreen and everything else on the phone works just fine now. I thought it was a defective item so it was exchanged with a new one.
Got the repair shop to replace it again and the outcome still remains the same as the first.
Theres no light coming from the screen nor the side illumination.
I just told the repair shop to just place the original back in for the mean time.
Before the repairs, there would be a flicker of white light and random illuminations. Now there's no lights at all except the power botton.
Could it be defective a batch that the seller was sending out? or the repair shop's mistake and is playing dumb so they do not have to admint fault?
Hopefully there's an easy fix to this problem.
-Also I did inspect the ribbon before and after the repair. looks new as the OEm
Can anybody help me out with this new problem after replacing the cable -
perhaps you should try a hard reset. Ive had problems in the past where the optical joystick and the illuminators did not work, and that worked for me.
On the other hand, the top illuminators are on the same piece of hardware as the flex cable that was replaced, so a faulty flex cable is possible. The bottom illuminators are on the circuit board that the optical joystick attaches to, separate but connected to the flex cable.
Ive recently replaced my flex cable and touchscreen. The experience i had with the faulty touch screen was that it appeared to receive no power, but was in fact displaying a dark backlit illumination that could only be seen in the dark. At the same time however, the screen did not display anything. I'm not sure if this is similar to your experience, but if so then your touchscreen would need to be replaced.
ive done all repairs on the xperia myself, and one thing ive discovered is if something doesnt work right after a repair, simply disassembling it and reassembling it to make sure all the connections are properly done has worked for me in the past.
"Before the repairs, there would be a flicker of white light and random illuminations. Now there's no lights at all except the power button."
Now when you say the power button, do you mean that a red light appears under it?
I dont know if i can come to a conclusion or that i can help (or have helped) you come to a conclusion, but i can only assure you that the xperia acts out in strange and weird ways.
Good Luck!
Tags
Dismantle / Disassemble Sony Ericson Xperia X1
http://www.ifixit.com/Teardown/Sony-Ericsson-XPERIA-X1/788/1
http://www.formymobile.co.uk/xperiadisassembly.php
http://www.youtube.com/watch?v=AWDurQrRt-Y (REAR)
http://www.youtube.com/watch?v=iyGUbxFqvyc&feature=related (FRONT)
http://www.youtube.com/watch?v=elgC8hwHfYQ&feature=related
For info.
Mike
Thanks for the links. I've tried the hardreset and restoring the original rom but the issue is still there. It's really bugging me that everything works but the LCD screen. I'm currently using MyMobiler to use my phone. The touch screen works fine and so does the soft keys. Just no power for the lights. I might just give up and wait for another phone that catches my eye and then tinker with the xperia myself. but if anyone got a solution or want me to test something then I'll give it a try.
My warranty is no longer affective so I'll use my phone as a tester to help others with any problems.
TRIONDAVE, how's your Xperia running now with the cable mod that you did? Its been 6 months since you created the thread. I hope you're still around.
My Xperia X1 works nearly fine, except for the keyboard issues, so I'm thinking of opening it up. If your Ribbon mod helped I might just do it too once I've got it opened. Mine has a MOUNTain of cracks though, and the battery compartment itself is cracked on both side enough to make the compartment CURVED. Hence the Battery cover doesn't sit well.
I'm looking around for broken Xperias which I might be able to use to change the internal cracked casing. Lets see.
DatDereX1 said:
cool story bro
Click to expand...
Click to collapse
My thoughts exactly.
Hello guys, I am in need of real help over here!
Its just that Ive replaced my ribbon cable, the old one got screwd up.
However I got done for 10 minutes ago, tried to start up the phone.. without success :,(
The ribbon cable doesnt have anything to do with the start up, only the screen am I correct? Cause I cannot even start my phone..
Ive connected the charger, but when I remove the battery it shows a red light, meaning no battery, correct?
So what may the problem be exactly? Maybe the battery is all dead, or?
PLEASE HELP!
for the people with ribbon failures how long have you had the phone before it occurred ? im just interested on the cables lifespan.
mine is fine so far but i have noticed the slider is flimsy and rocks left and right.

Soft keys only respond to the S-pen

Hey, guys.
So in Short my Note 4 fell from my mom into the seawater, I got it out and dried it and it kept freaking out for several days, but then slowly restored all functions normally.
Well, except that the soft keys don not light up or respond to fingers. Only to the S-pen
Is there any fix to it? and is it a hardware issue? I went to the Customer care and without even checking they said they'll change the entire touch screen, which will cost almost 60% of the mobile price
Any help here please?
Could be the charging port board. The keys are integrated in it.
I had the same issue with my back button after i swapped a malfunctioning charging port.
Now I changed it again and although I restored my back button functionality (with minor hiccups), it still doesn't light up, so I turned off the lights on both buttons.
Considering I have the wakelock app on to keep it alive, having replaced the battery twice and having disassembled it several times, I am happy with what I have.
Sometimes I just wish it would die so I have a reason to buy a new phone, but as long it turns on I won't go to another device.
gustic.gx said:
Could be the charging port board. The keys are integrated in it.
I had the same issue with my back button after i swapped a malfunctioning charging port.
Now I changed it again and although I restored my back button functionality (with minor hiccups), it still doesn't light up, so I turned off the lights on both buttons.
Considering I have the wakelock app on to keep it alive, having replaced the battery twice and having disassembled it several times, I am happy with what I have.
Sometimes I just wish it would die so I have a reason to buy a new phone, but as long it turns on I won't go to another device.
Click to expand...
Click to collapse
Problem is, It's 5 months old now and I'm borke to afford a new one that soon.
Plus everything works perfectly except touch on them despite that they work fine with the pen
Guess I'll have to settle with any app to draw soft keys on my touch screens, since I'm not replacing a 4000 pound screen just to fix the keys
I just hoped that someone had run into that issue and fixed it

Categories

Resources