Hello All,
my device is sticked on smart mobility it going hang on that only
what should i do for start my phone ? i was try to flash my phone but it was gives
207 error.
mehulkarate said:
Hello All,
my device is sticked on smart mobility it going hang on that only
what should i do for start my phone ? i was try to flash my phone but it was gives
207 error.
Click to expand...
Click to collapse
Have tried pulling out the battery? Flashing a stock rom first? Can you enter the tri-color screen? What spl did you install?
kwbr said:
Have tried pulling out the battery? Flashing a stock rom first? Can you enter the tri-color screen? What spl did you install?
Click to expand...
Click to collapse
no i don't install any spl.i try it but my phone will not sync becoz phone was gone start.i wont to start my phone only.
it give one error
device start up failed due to sudden loss of power.please click "yes" to continue.
note.
do not remove battery before device has been completely shutdown off
mehulkarate said:
no i don't install any spl.i try it but my phone will not sync becoz phone was gone start.i wont to start my phone only.
it give one error
device start up failed due to sudden loss of power.please click "yes" to continue.
note.
do not remove battery before device has been completely shutdown off
Click to expand...
Click to collapse
Have you tried flashing a stock rom?
kwbr said:
Have you tried flashing a stock rom?
Click to expand...
Click to collapse
i was find my device id -ELF010050, CID -DOPOD0100 and i flashed my phone with those roms like
1)RUU_Elfin_DOPODASIA_WWE_2.20.707.1G_4.1.13.51_03.07.90_GREEN_Ship_Reduced
2)RUU_Elfin_hTC_Asia_India_3.07.720.03_4.1.13.71_03.34.90_BLUE_Ship
3)RUU_Elfin_hTC_Asia_WWE_3.07.707.02_4.1.13.71_03.34.90_BLUE_Ship(frome official web site htc/asia.com)
flashing was complete 100% but my phone don't start from smart mobility.
mehulkarate said:
Hello All,
my device is sticked on smart mobility it going hang on that only
what should i do for start my phone ? i was try to flash my phone but it was gives
207 error.
Click to expand...
Click to collapse
you need version CID and Device ID and the latest version here
and after you finish you can Up rom 6.1-6.5...ect
^^! You remember thank!
takatori said:
you need version CID and Device ID and the latest version here
and after you finish you can Up rom 6.1-6.5...ect
^^! You remember thank!
Click to expand...
Click to collapse
i know that but my device not cid unlocked so i can't flash Hard-SPL.it going only on bootloader mode.
mehulkarate said:
i know that but my device not cid unlocked so i can't flash Hard-SPL.it going only on bootloader mode.
Click to expand...
Click to collapse
Use a goldcard
recover my elfin
kwbr said:
Use a goldcard
Click to expand...
Click to collapse
hello all
i have recover my elfin and i installed uspl and then update my spl,ipl then flashed by onyx_6_release14 rom so rom run superb.
thanks all
Related
Hi
I recive SPV C500 when i power phone in display i have only Orange logo and Phone power off
I make updrate to MW6 phone alive but now i have Network problem
Please how to solve this problem if is it software problem
thanks
f6_gsm said:
Hi
I recive SPV C500 when i power phone in display i have only Orange logo and Phone power off
I make updrate to MW6 phone alive but now i have Network problem
Please how to solve this problem if is it software problem
thanks
Click to expand...
Click to collapse
can you get into bootloader?
hi
Yes i can put phone in boot mode
what can i do
thanks
f6_gsm said:
hi
Yes i can put phone in boot mode
what can i do
thanks
Click to expand...
Click to collapse
what dose it say on the screen when you go into thr bootloader
rickwyatt said:
what dose it say on the screen when you go into thr bootloader
Click to expand...
Click to collapse
IPL 1.00
SLP 1.01.0109
UI
f6_gsm said:
IPL 1.00
SLP 1.01.0109
UI
Click to expand...
Click to collapse
you need mtty.exe to flash yo ur phone you can use wm5 or wm6 go here
http://www.geocities.com/gggbitonti/typhoon.htm
Hi
I use Mtty1.42 and flash my phone with WM6 my phone power on now but don't have Network
rickwyatt said:
you need mtty.exe to flash yo ur phone you can use wm5 or wm6 go here
http://www.geocities.com/gggbitonti/typhoon.htm
Click to expand...
Click to collapse
I make all operation for http://www.geocities.com/gggbitonti/typhoon.htm
phone alive but now it have Network problem
f6_gsm said:
I make all operation for http://www.geocities.com/gggbitonti/typhoon.htm
phone alive but now it have Network problem
Click to expand...
Click to collapse
did you ever upgrade your c500 with the orange update? frist go to settings on your phone then go to about what is your radio version mine is 1337.0.42_0.03.28
rickwyatt said:
did you ever upgrade your c500 with the orange update? frist go to settings on your phone then go to about what is your radio version mine is 1337.0.42_0.03.28
Click to expand...
Click to collapse
No i no updrate phone with orange update
Windowns Mobile r 6
OS 5.2.318 (Build 15341.0.0.0)
Radio Version 1337.0.32_0.03.18
please need u contact
thanks
f6_gsm said:
No i no updrate phone with orange update
Windowns Mobile r 6
OS 5.2.318 (Build 15341.0.0.0)
Radio Version 1337.0.32_0.03.18
please need u contact
thanks
Click to expand...
Click to collapse
your going to have to go back to wm3 to get your radio upgraded
go here follow
http://www.user.cityline.ru/~ronswens/tutwm2003.html
to the letter, until you get to the part where you have to type in
format BINFS
if you get "Not allow operation" after typing
>format BINFS
then try this
>info 2 <--------- note the space between info and 2
then type in
>format BINFS
then restore this http://www1.orange.co.uk/c500patch/
this will upgrade your radio to the one i use then go here http://www.geocities.com/gggbitonti to go back to wm6
Now my phone don't connect with activesyn 4.1 when i try to install activesyn 4.50 i have error :
Error. There is problem with Windows Installer package; A DLL requiered for this install to complete could not be run. Contact your support personel or package vendor.
i have windows service pack1
f6_gsm said:
Now my phone don't connect with activesyn 4.1 when i try to install activesyn 4.50 i have error :
Error. There is problem with Windows Installer package; A DLL requiered for this install to complete could not be run. Contact your support personel or package vendor.
i have windows service pack1
Click to expand...
Click to collapse
try download activesync 4.5 again if that dont work
try uninstalling 4.1 frist reset computer then try active
sync 4.5 again did got wm3?
My phone is always in bootloader mode, even after upgrading a new rom...
Any ideas how to get back to "normal" mode....
Thanks
While in bootloader mode, connect via USB and try to flash down to wm5. It worked with nanoscopic step1 for me. Then i was able to reflash any wm6 again.
What version of ROM you're using??
hugot said:
My phone is always in bootloader mode, even after upgrading a new rom...
Any ideas how to get back to "normal" mode....
Thanks
Click to expand...
Click to collapse
No matter what you have, reinstall PDAVietTemp to recover
http://wiki.xda-developers.com/index.php?pagename=PDAViet Upgrade Tips and Tricks
hugot said:
My phone is always in bootloader mode, even after upgrading a new rom...
Any ideas how to get back to "normal" mode....
Thanks
Click to expand...
Click to collapse
If you are upgrading to WM6, you need to HardSPL your prophet.
See this post http://forum.xda-developers.com/showpost.php?p=1718372&postcount=6
Before you do the HardSPL check if you have a G3 or a G4!
I everyone,
I was trying to intall a new rom in my Pharos but the computer crashed and the instalation was interrupted. Now Pharos doesn't conect, and when i try to install the rom again it says invalid vendor id or update error. I think is dead
Does anyone have the original Pharos Rom WM6 Eng ? or know where i can find? so i can try to save it.
Thanks
rom: 1.11.405.1
rom date: 01/29/08
radio version : 03.15.90
protocol : 4.1.13.59
maybe you can use this one : http://forum.xda-developers.com/showthread.php?t=394721
Thanks Teckynou, i have already tryed that on. Doesnt work, its the wm6.1 (update), i think i have to install again the original Rom in Eng. (and i dont find anywhere)...
have you tryed a hardreset?
http://www.hardreset.eu/htc_pharos_p3470_hard_reset_soft_reset_en.html
Yeap! didnt work....i really need help.
at_mix said:
Yeap! didnt work....i really need help.
Click to expand...
Click to collapse
If all else failes send it to HTC... and theyll repair it .. will probably charge you since you tried to flash (an unofficial) rom but its better than having a brick.
Maybe someone else has a better idea?
lots of luck to you!
Another Original ROM
http://forum.xda-developers.com/showthread.php?t=403957
What U mean by "DEAD"...?
Have U managed to have the tri-colors boot screen?
Tri-color Boot screeen is looked similar to this.....
http://www.ismodel.net/forum/richedit/upload/2kcf486c647d.jpg
If not,...
Try the method below to get the Tri-color boot screen. Though it is for ELF, it usually works to all HTC devices. Surely..work on Pharos..
I recommend Hold down camera key => Press/Release Reset Button at the back => Release camera key after you have the tri-colour boot screen showed up.
http://wiki.xda-developers.com/index.php?pagename=Elf_Resets
Then you can flash an original ROM... Note it is OK that 'Active Sync' symbol show "NOT CONNECT".. U can still proceed with Flashing!!!!!
Let me know if it works this time.......
bita said:
Another Original ROM
http://forum.xda-developers.com/showthread.php?t=403957
What U mean by "DEAD"...?
Have U managed to have the tri-colors boot screen?
Click to expand...
Click to collapse
Hi Bita,
Yes, im able to enter the reboot (the tri-colors boot screen), the only problem is the rom i try to flash i get the ERROR vendor id or update error.
I'll try that original rom.
Thanks
Hi to all
In rom update process (around 23%) my p3300 turn off with an error about FLASH and after it I can't turn on it and also I can't enter to boot loader.
Any idea?
Thanks a lot.
Did you run USPL before you flash?
Did you tried enter bootloader with Power+Voice speed dial buttons pressed together?
If you have the shipped ROM try to flash it.
Did you run USPL before you flash?
Click to expand...
Click to collapse
yes i run USPL before flash.
my ppc was cid unlock.
Did you tried enter bootloader with Power+Voice speed dial buttons pressed together?
Click to expand...
Click to collapse
yes, but no answer from my ppc !!!!!!!!!!!!!
If you have the shipped ROM try to flash it.
Click to expand...
Click to collapse
i have it. but i can't enter bootloader to flash my ppc!
any idea ?
any help !!??!!
hey is there any body ?
mehdirm666 said:
hey is there any body ?
Click to expand...
Click to collapse
Maybe you can use SD-card flashing? You could use that to flash a very small rom like YuE extra clean
Can you enter the bootloader via this method?
If not do you get an error msg?
Maybe you can use SD-card flashing? You could use that to flash a very small rom like YuE extra clean
Can you enter the bootloader via this method?
If not do you get an error msg?
Click to expand...
Click to collapse
hi
i can't turn on my ppc !!!
i can't enter bootloader !!! camera and power button not work !
even my ppc's battery not charge !
i guess my ppc's bootloader damaged!
any idea ?
this is not SPAM ! ()
I just occur the problem just like as minhanh_tran have happened.
when I flash a Orange ROM to my T01A, it entered white screen and began downloading, and when it finished it give a messege that the phone will restart automatically.
all this looks like boot right,but after restart the screen is blue screen,that mean I can see the backlight is open,but the screen have nothing,without the docomo logo or toshiba logo.....
when I try the method as minhanh_tran and stepw said, I push out the microSD,and short the pin 1 and 3,connecting the usb to my pc, then the PC find a new hardware, hinting that I enter DL mode and I should give TG01 DL driver.....so,what should I do?
bird_9527 said:
I just occur the problem just like as minhanh_tran have happened.
when I flash a Orange ROM to my T01A, it entered white screen and began downloading, and when it finished it give a messege that the phone will restart automatically.
all this looks like boot right,but after restart the screen is blue screen,that mean I can see the backlight is open,but the screen have nothing,without the docomo logo or toshiba logo.....
when I try the method as minhanh_tran and stepw said, I push out the microSD,and short the pin 1 and 3,connecting the usb to my pc, then the PC find a new hardware, hinting that I enter DL mode and I should give TG01 DL driver.....so,what should I do?
Click to expand...
Click to collapse
Mmmm, did you try to flash a rom by pin recovery method?
arag0n85 said:
Mmmm, did you try to flash a rom by pin recovery method?
Click to expand...
Click to collapse
yep，I have try using this method.
and I can enter the downloading screen and can finish downloading,and then the screen give the right messege"flash successful , the phone will restart automatically".......but after restart, the phone is still back screen, I can not see the toshiba or docomo logo...
bird_9527 said:
I push out the microSD,and short the pin 1 and 3
Click to expand...
Click to collapse
You should NOT remove micro SD...
You need to put your official Rom on the micro SD and then short the pins...
bird_9527 said:
yep,I have try using this method.
and I can enter the downloading screen and can finish downloading,and then the screen give the right messege"flash successful , the phone will restart automatically".......but after restart, the phone is still back screen, I can not see the toshiba or docomo logo...
Click to expand...
Click to collapse
Did you try with a diferent ROM?
right
arag0n85 said:
Did you try with a diferent ROM?
Click to expand...
Click to collapse
I have tried all kinds of ROM, including ORANGE\GERMEN\DOCOMO official ROM,all this can download to my t01a, but after restart, the screen is still black and can not enter the docomo or toshiba logo and can not open....
bird_9527 said:
I have tried all kinds of ROM, including ORANGE\GERMEN\DOCOMO official ROM,all this can download to my t01a, but after restart, the screen is still black and can not enter the docomo or toshiba logo and can not open....
Click to expand...
Click to collapse
Rare thing... but if you can flash properly a DOCOMO ROM, i would recommend you to use the "toshiba service", they don't have a way to know if that happened while you were updating your rom or flashing a custom ROM. Anyways, I don't know what should be happening, you should try to use .enc extension in your DOCOMO original ROM just to try.
arag0n85 said:
Rare thing... but if you can flash properly a DOCOMO ROM, i would recommend you to use the "toshiba service", they don't have a way to know if that happened while you were updating your rom or flashing a custom ROM. Anyways, I don't know what should be happening, you should try to use .enc extension in your DOCOMO original ROM just to try.
Click to expand...
Click to collapse
I have tried many ROM, by all the way (pin 1+3, change ROM file to *.enc, bin...) but after ROM have flashed successfully, it restarts and nothing more, only backlight.
yep
minhanh_tran said:
I have tried many ROM, by all the way (pin 1+3, change ROM file to *.enc, bin...) but after ROM have flashed successfully, it restarts and nothing more, only backlight.
Click to expand...
Click to collapse
my t01a just like as your condition......waiting for the solution tools......
congraturation!