wp7 reset problem - HD2 Windows Phone 7 Q&A, Help & Troubleshooting an

hi guys
i have a htc hd2 and i installing a windows phone 7 on my htc, i have a 8gb ram class 2 ! my question : i Complete the install wp7 with no error and perfect running on my phone ! but when i first shuting down my phone and i turn on again, my phones booting up until logo htc wp7 but my phone Constantly reset!!,sorry if bad speaking and bad typing im from iran ! and htc company is not supporting here ! please help me!
thanks

you can try 2 solution:
- flash ROM without SDcard and upgrade until version 7392, then go to settings - about - reset my phone and when booting insert card und upgrade to 7720
- if ROM already flashed, take out SDcard, go to settings - about - reset my phone, upgrade until version 7392, then go to settings - about - reset my phone and when booting insert card und upgrade to 7720

Related

Htc p3400 hanged at start up page onyl

Dear Please help my PDA HTC p3400 has hanged at started up only at front screen only it is not moving further. i had done hard restet also then also not working. Please help me out .
Waitng for reply.
hard reset
Jeet8626 said:
Dear Please help my PDA HTC p3400 has hanged at started up only at front screen only it is not moving further. i had done hard restet also then also not working. Please help me out .
Waitng for reply.
Click to expand...
Click to collapse
do hard reset
i had done hard reset also
Try to bootup without the SD card (and may be SIM), I had this problem with my Vox, the SD Card was corrupted. After formatting the SD Card, everythig became normal.
Best of Luck
Same problem
Jeet8626 said:
Dear Please help my PDA HTC p3400 has hanged at started up only at front screen only it is not moving further. i had done hard restet also then also not working. Please help me out .
Waitng for reply.
Click to expand...
Click to collapse
Hi!
i have the same problemwith my P3400
i have made the upgrade to wm5 to wm6.1
the pda at the first time has booted and i have configured the regional time and the pen alignment until the the screen that says Setup complete, click to proceed (or something like this).
After this, it gets stuck on the windows mobile 6.1 boot screen
i have made the re-update with the same rom update.
the problem persists!
I have made with/without sd card and sim.
Now when it boots apears
ONBL 1.07.0000
SPL 1010.olip
GSM 02.84.90
OS 1.17.0.0
then changes for the wm6.1 boot screen
and stucks here
S/n-SZ716FW06338
XT01
GENE 100 (old gene i think)
please help me
thanks in advance
Pedro Matos (from Portugal)
matosmatos said:
Hi!
i have the same problemwith my P3400
i have made the upgrade to wm5 to wm6.1
the pda at the first time has booted and i have configured the regional time and the pen alignment until the the screen that says congratulations, click to proceed (or something like this).
After this, it gets stuck on the windows mobile 6.1 boot screen
i have made the re-update with the same rom update.
the problem persists!
I have made with/without sd card and sim.
Now when it boots apears
ONBL 1.07.0000
SPL 1010.olip
GSM 02.84.90
OS 1.17.0.0
then changes for the wm6.1 boot screen
and stucks here
S/n-SZ716FW06338
XT01
GENE 100 (old gene i think)
please help me
thanks in advance
Pedro Matos
Click to expand...
Click to collapse
i have done it!
Now i have the wm6.1
i found another rom update! (coooollll!!!!)
heheehehehhe
thanks anyway!
i have the same proplem you had can you tell me how you done it with new rom espiecly i cant flash room and i cant do anything
thanks
for ur info @matosmatos
hi
as per the numbers quoted by u urs is a old gene so falsh roms for old gene only this is just for ur info
goodluck
matosmatos said:
i have done it!
Now i have the wm6.1
i found another rom update! (coooollll!!!!)
heheehehehhe
thanks anyway!
Click to expand...
Click to collapse
@smb_do
hi
assuming ur phone is just dead ie just blank screen do this
1.power off the phone remove batter and press the power button 3 secs
2.put batter back in to the phone
3.Press camera button and then power on at the same time u will get tricolor
used usb and Flash new ROM
or press camera button and do soft reset using stylus this will also give u the tricolor use USB and flash new ROM
goodluck
smb_do said:
i have the same proplem you had can you tell me how you done it with new rom espiecly i cant flash room and i cant do anything
thanks
Click to expand...
Click to collapse
thasnffffffffff
Im so so saaaad
I try avery thing hard reset , now roms every time it accept the now rom and whine it restsrts again tha same problem it stop at
ONPL 1.07.0000
SPL 1.07.oref
GSM 02.79.90
OS 1.9.1.1
please help me send me at
ahmedrefaat82/hotmaill.com
gene hanges at start up page onyl (after rom Upgade)
I am also facing the same problem. I have old Gene. I had upgaded it to
Pro User's ROM WM 6.1 Sumit
Everything was running fine till I soft reseted the device. On soft reset it stucks at the start up screen
On boot it shows following
ONBL 1.07.0000
SPL 1010.olip
GSM 02.79.90
OS 1.17.0.0
Then it shows the windows animations and then it hangs.
This has happned to me twice.
I had installed following applications after the ROM upgrade. Does any application creating a problem
1) HTC Home (6 tab plugin)
2) S2U2,S2P,S2V
3) Quick Menu
4) Opera Mini
5) TCPMP with many codecs
satishgosavi said:
I am also facing the same problem. I have old Gene. I had upgaded it to
Pro User's ROM WM 6.1 Sumit
Everything was running fine till I soft reseted the device. On soft reset it stucks at the start up screen
On boot it shows following
ONBL 1.07.0000
SPL 1010.olip
GSM 02.79.90
OS 1.17.0.0
Then it shows the windows animations and then it hangs.
This has happned to me twice.
I had installed following applications after the ROM upgrade. Does any application creating a problem
1) HTC Home (6 tab plugin)
2) S2U2,S2P,S2V
3) Quick Menu
4) Opera Mini
5) TCPMP with many codecs
Click to expand...
Click to collapse
Not likely, try a hard reset and see if your issue is solved
Addicted2xda said:
Not likely, try a hard reset and see if your issue is solved
Click to expand...
Click to collapse
I had tried that also but not able to recover I had to burn the ROM again .
I am scared now to soft reset my gene. Never know when it will get hanged again. (pls note that it does not hang on every soft reset).
I liked the new ROM (6.1 pro Sumeet) so much. It is fast and have left enough room to add/execute other applications. I have read so many good comments about the ROM. I do not want to change it to any other version.
Please.. please try to get some solution.
Thanks in advance.
regards
Satish
It Worked
Thanxxxxxxxx

URGENT: cannot boot X1 anymore

hello,
since yesterday I cannot boot my X1 anymore.
Rebooting starts, then I get the screen where I have to enter a security code (thanks to my company`s security policies...) and I cannot enter values there. After a few seconds it stops booting. So I cannot proceed
Only option I see is to reinstall ROM/firmware.
My laptop cannot see the X1 via USB because it is not up and running, so I cannot move data/new ROM to the microSD.
Is there a Software/firmware/ROM-updates available (prefered: WM6.5 German, or at least WM6.1) which can be started/run from my laptop?
I couldnt find a download link to VodafoneGerman WM6.1 here
http://wiki.xda-developers.com/index.php?pagename=HTC_Kovsky_Shipped_Roms
thank you
Raggi
If you have soft SPL, you should be able to get into boot logger screen and update it thru the SE site/program.
Other option.. is there a card reader/adapter that fits the micro SD card for you to copy the ROM?
Edit: Does hard reset work at all?
hard reset doesnt work unfortunately.
Dont have soft SPL installed
my cardreader doesnt support microSD, so I guess I first have to buy a new one
is this the latest official Vodafone Germany WM61 ROM?
GENERIC deutsch DE (1.03.938.9) R2AA006
http://forum.xda-developers.com/showthread.php?t=477801
Now I called Vodafone Business SUpport and they dont have a link for me....
Try the following:
Enter bootloader (press the silver buttons and on/off button when phone is off)
Use SonyEricsson's update program.
IMHO it should update as the phone connects to usb with different mode than normally.
great, a few hours later and got it working.
I went into town and but a new cardreader. in the meantime my X1 woke up
and I could use the SE update installer.
So now I have got a newer WM6.1 (ROM 1.03.162.10, radio 1.10.25.18) running which is so much faster than my old system
now time to enjoy the sun....
Strange, almost the same thing happened to me on that very day... Phone stopped booting after the SE logo (Animation didn't show up). Had to Hardreset after several attempts to solve the problem...

please help!! after ROM upgrade the device stuck completely!

please expert guys help ...
i have new leo with ROM 1.43 today after trying to upgrade to ROM 1.66 I did everything as asked, the installer began , with all the colours on the leo display then it started the percent completion counter , and after 2% it wrote me error something , and the leo restarted but stuck in the white start up menu with the green HTC icon and below the R G D information but the device doesnt proceed further and stuck here !!!
please help !!!!
it write me as i recall
it wrote me if i recall right :
INVALID MODEL ID
did you install HSPL before trying to install the ROM?
no i didnt try to install anything !
no i didnt try to install anything ! , just started the intallation file ROM arabic-english , and did what i asked to do !
if i didnt install hspl what can i do ?
can i take the device to the shop i bought it from and use the warranty ?
well, no...did you get the file from HTC direct or off here? your phone could be vendor locked to your provider so if you can get the original ROM that was on your phone you can flash that back on...
you should really read into things before jumping in at the deep end...
well i have an inlocked device ...
o bought the device in europe , but i am from israel , htc sent me notification about new arabic ROM with link , i tried with my serial to download but couldnt , it wrote me "this upload not compatible with ur device" , i downloaded it from here XDA developers , but it went wrong !! , the problem that the phone stuck in the loader menu , before uploading the sense interface , and i have no connection between the pc and the phone "no active sync" so how can i reinstall the older version or make the phone load again ?!!?!! plz help !
you need the original ROM and a connection to your PC. run activesync as even not working it should connect up...
no there is no connection the device centre says not connected
the phone is not responding and the pc doesnot establish connection with it , i am stuck with loading menu with the R 2.04.50.22~2
G 15.26.50.070
D 1.43.7024
from there nothing moving , if i do soft reset it , it stucks again in the same menu !!!
i didnt install HSPL , and i guess i tried to install not the correct region ROM upgrade , the phone was purshased in lithuania , but htc offerd me middle eastern ROM because i want the arabic - hebrew support !
plz help
You could try installing the Shipped ROM via microsd card method. Just make sure your battery is above 50%. then follow these steps:
1. Using 7Zip, Open your Shipped ROM.exe (You need your exact shipped ROM for this, anything else will give you the error you got)
2. Look for the "RUU_signed.nbh" (without the quotes)
3. Copy RUU_signed.nbh to your microsd card AFTER formatting the microsd as FAT32 (quick format works well enough, using Win 7)
4. Rename 'RUU_signed.nbh" to "LEOIMG.nbh" (again, without the quotes)
5. Take out the HD2 Battery and insert microsd card in slot.
6. Put Battery Back on and hold the "Vol Down" key while pressing the Power key
7. Follow the instructions on the screen... (remember you need at least 50% battery power just to make sure everything goes as planned)
8. Soft Reset after your done and you have a "Fresh" Shipped ROM on your HD2!
Optional:
9. Install HSPL (use the guide that's been stickied in the ROM Dev Section)
10.Flash the ROM of your choice via MicroSD method or activesync (again, please read the Stickied guides in the ROM Dev Section)
Good Luck!
total storage 328 instead of 180 !!!
well i didnt need anything to do, i pressed and hold the up vol. and down volume and pressed the power key , it did a hardreset and my old ROM back to me , though i noticed strange thing !!!
after the hardreset back to my old ROM i checked the SD card & phone storage and i found that i have now total storage 328 instead of 180 !!!
but then i upgraded my ROM this time with legal one from HTC support site , and the total storage got back to 180 again !!!
anybody knows what happened here ?!
p.s thank u guys for the help

[Q] HD2 Lockup on install

Hi folks.
I've just tried to flash my HD2 to Gingerbread from WinMobile 6.5 using the following instructions:
http://forum.xda-developers.com/showthread.php?t=905060 (It's in HTC Leo: HD2HD2 AndroidHD2 Android NAND Development[3.May.11][MAG/cLK] NexusHD2-Gingerbread V2.7 [GRJ22/Android2.3.4][Kernel:tytung_r10])
The HSPL installation went fine, however, when used the ROMUpdateUtility.exe, I've been left with a phone that won't boot past the O2 Welcome screen?
Can someone please tell me what I'm doing/done wrong? I've now got a phone that's useless No amount of resetting, rebooting or hard resets will change it.
Cheers!
Further update
Where it tells me to boot the phone whilst holding the power key down, it doesn't appear to do anything. If I do a cold boot, the phone just will not boot (but then it didn't under Windows) and if I hold it down & do a soft reset, just still goes to the O2 Welcome screen. I can put it into the ROM update Utility again & attempt to reflash the ROM (which now shows no Version number) and I get the screen that tells me The ROM Update is complete, although it takes only about a minute, as opposed to the 10 it should take!
FYI, the Phone ROM Update Utility is version 3.27.4.3, if this helps?
Ta!

Phone locks up on first update

Hello
I am following the guide to install the 7720 rom by means of updating via zune.
I flash V2 and perform all of the steps, then i went to upgrrade from 7000 to 7280 via zune, it gets half way through and then windows says 'USB device has malfunctioned' and the phone freezes, now when ever i boot into my phone it freezes.
Any way of trying again without having to re-flash the rom using magldr?
On magldr menu there is an option to hard reset, or should i reset using the vol buttons on startup?
Thanks
Just answered my own question.
Tried another USB cable and rom flash was 20x faster!! must have been a dodgy cable.... crappy ebay quality for you!
Okay, no i havent fixed the problem.
During the process of installing the update, it restarts the phone, then it restarts the phone again, except the second restart round, the phone locks up just afteer loading the wp7 rom, any ideas? its stuck on stage 8, restarting the phone.
Okay it seems to be going ok now, it was because i didnt do the Clear MBR SD thing and the 24MB thing, but i wont speak too soon like i did last time!
Hello,
I have the same problem, after the first zune update, the phone locks and I can't do anything... I did the 24MB thing and Clear MBR SD, I tried to use different SD Cards ( 2gigs and ADATA 16Gos Class 6) same problem...
Please Help!
I used both of these SD Cards on WP7, is it the reason why WM 6.5 does not detect both of these SD Cards (so I can't format them?)?
Tried to get an "old" version (NODO) working but I guess I will have another SD Card to buy... =/
The SD cards are locked and you need format them with an old Nokia. Magdlr, new Nokia's, Windows Mobile 6.5 or Windows Phone 7 won't work.
I have the same problem. Get a touch screen freeze when I'm updating thru Zune. Only way to recover my mobile is to remove my SD card. Then it boots and is working again.
Did u tried the whole process from
-flashing a stock WM6.5 rom,
-then install radio,
-install Magldr (24Nand trick, Clear MBR)
-install WP7 ??
http://forum.xda-developers.com/showthread.php?p=17205251#post17205251
Actually WM6.5 wont recognize your SD card, but WP7 will able to reformate & install.
Meanwhile if you want to use this SD card on Android or WM6.5, you won't be able to.
Unless u've a Nokia
http://forum.xda-developers.com/showthread.php?t=1242071
I followed the original post of Yuxi and got stuck while I was updating to 7008. When I went to flash back to pre 7008 (dunno which version that is), I get an error (something about a usb-file that can't be found).
Now I'm flashing back to Windows Mobile 6.5 cause thats the only option that seems to work. Changed the radio also a couple of times but that didnt made a difference
Apparently for some HD2 users, the software "sdformatter" worked to get the SD Card working back, it didn't worked for me unfortunately.
Just tried with a brand new SD Card (Lexar 16Go), still freezes while zune updates and try to restart the device :-/.
I perfectly followed the different step, installing HSPL, WP 6.5, formatting SD Card, Radio, MAGLDR, Native Windows Phone 7, and then trying to update with Zune.
EDIT : I finally passed this step : I installed the v2 Yuki WP7 without SD Card, and updated with zune still without SD Cards. I finally reached the Nodo update (it took about 20 minutes) still without any SD Card. After that I inserted the SD Card and reinitialized the phone through "about phone". No problem so far. I'm going to try to install Mango.
Garsmat72 said:
Just tried with a brand new SD Card (Lexar 16Go), still freezes while zune updates and try to restart the device :-/.
I perfectly followed the different step, installing HSPL, WP 6.5, formatting SD Card, Radio, MAGLDR, Native Windows Phone 7, and then trying to update with Zune.
EDIT : I finally passed this step : I installed the v2 Yuki WP7 without SD Card, and updated with zune still without SD Cards. I finally reached the Nodo update (it took about 20 minutes) still without any SD Card. After that I inserted the SD Card and reinitialized the phone through "about phone". No problem so far. I'm going to try to install Mango.
Click to expand...
Click to collapse
how did you get on? ive hit the same problem on the 7008 update using the xboxmod/yuki v2. Im currently re-flashing and starting again but this time i will leave the SD card out

Categories

Resources