Database Users

Vario hang on first bootscreen

I have just installed SPB Clone correct on my Vario. Now this program did a soft-reset and the Vario just hang on de first bootscreen. (The one with the soft-/firmware version on it.)
SPB Clone has installed a program that would startup at first program while booting. My Vario don't seem to like that.
Is there a way to remove this program/problem without a Hard-reset. I don't like to lose my data.

I had the same problem..
you can only erase all data by installin the rom on top.
boot in USB mode, Hold the camera button and the reset pin and it will start in tree color mode, USB
Than install a rom from the computer... about 10 min.
A.

Do you have more information about that, what it does and how it works.

1) Fist you will have to find a rom update or corrent version of your phone.
I don't know what you have K-Jam or qtek 9100..
K-jam rom you can find at the support site, club i-mate
Qtek:
http://www.beyondthetech.com/blogs/kjam/2005/11/qtek-9100-rom-available-for-download.html
2) Boot the phone in USB Mode: Hold camera batton on the side and with the pen into the reset hole. USB screen will come up.
3) plug USB cable into computer, and run downloaded software.
10 more minutes and reset phone, all done....
Good luck
Clone is very dissapointing, I am using Sunny Backup Manager 3.7 now!

i had this problem too after installing SPB pucket plus. do you have this installed? if so just goto the options and uncheck safe mode and it should boot fine now, obviously wont help you until you have wiped the machine, but it will avoid the same problem again

stuck at boot loader -cant connect to pc

Hi,
I tried a new rom and now am stuck at the bootloader with no OS on the phone.
ipl 2.10.0001
spl 2.10.0001
gsm 02.69.21
os 4.0.0.0
I have searched all the forums and still cannot get my spvm600 to do anything. I have tried to run several roms but the problem is they cant see the phone as activesync wont connect. is there a way i can boot from the sdcard or somthing or do i have a expensive paperweight. when i try to hold down the camera and comms keys on start it asks me to format the device and then says doen and goes back to the above screen

anyone?
ideas?

Try to restart your device and deliberatly go to boot loader (keep camera button in) (keep usb disconnected).
once at boot loader screen connect usb cable ... you should now see "usb" in bottom left corner on device screen.
now run a wm5 rom like in step 1 of "how to upgrade from WM5 to WM6" thread - - http://forum.xda-developers.com/showthread.php?t=310452.
it worked for me!

every rom i try to install on it needs activesync to connect to it but activesync douesnt connect to it as the phone has been formatted. there must be a way to fix it but but i am totally stuck

Rom Upgrade doesnt need Active Sync, you just need to be in bootloader and have the usb cable connected. Then just go through the update utility.

I try that and it still seems to say no device connected would you like to try copying again. I cant understand it cause it makes that bling noise when i plug it in

Use Update_NOID
You must use the No_ID Updater to upload a ROM from the 3 colour screen. Just run this exe file and you should not have any problems.

Hi,
Please help, I too have the same problem. Installed all the versions but no use. Can any one help me how to downgrade to Original German ROM version for Neo. So that I can return to O2 company... otherwise this become expensive paper weight

thankyouthankyouthankyou
YEEAAAAHHH
my phone is now working.
the no id rom worked a treat.
xtrafletch thanks a million!!

i reeallyyyy need somebody's help with unbricking my phone.. please hellpppp!!

alright.. i made a similar post to this before and i came across the wiki...
well i can't view what my SPL or my IPL because as soon as i turn the device on, all that shows is the boot loader screen and displays serial on the top with 0.16-0.90 in red characters on the bottom (I'm not sure what those are)...
here are the only details that i know about my phone:
I DON'T have hard SPL
My Original ROM i was using before was an htc windows mobile 5 rom
The reason that my phone is bricked right now is because the usb cable disconnected in the middle of the flash
I'm using Windows Vista for flashing
Computer won't recognize the phone when on usb
My phone (qtek 9600) can't load the operating system
*EDIT*
THE PHONE IS STUCK ON BOOTLOADER WHEN I TURN IT ON, NOTHING ELSE, BUT THE BOOTLOADER SCRREN DOESN'T SHOW MY SPL AT ALL.
ALSO, MY COMPUTER DOESN'T RECOGNIZE THE PHONE....... MY PHONE HAS A TYPE 2A BRICK
Helping me will be greatly appreciated
come on.. I'm without a phone

Do you have a 2GB or smaller SD card? Copy a rom image to it and rename it HERMIMG.NBH
Turn it on and you might get lucky!

Just make sure its stock rom that was supplied, or the updated WM06 version as the CID should check out then...
vwkess forgot to mention, reset into bootloader, hold power, ok button and reset with stylus. Hold all buttons in until you get to the tri-colour screen. If it works, follow the prompts....
Cheers...

hi,
i think i can hlep.
i had recently bricked my phone with a custom wm6 image, it worked fine for two days and then i reboot, and all i see was the welcome image, nothing else.
so what i did is -
i pressed the hard reset buttons - power + OK + SOFT RESET (Stylus), kept it pressed for 3-4 seconds, the fone rebooted, the screen was full with some colored bricks i connected my fone in USB and on screen i saw USB.
I then again flashed my fone with the working update, it worked perfectly for me, try may be you can get some luck
ps - before doing all these, i turned my fone off by removing the battery, i removed sim card and mmc card as well.
regards

That may work too, but again, try to flash with a stock rom, untick "connect with USB" in activesync and then try.
Make sure you go to boootloader screen, instruction in rajivlodha's post, before you connect to the pc.
Goodluck...

I need some help as well.
I think I may have bricked my phone. It's a rooted htc hero cdma. I'm running cyogenmod on it and it was working fine, until using metamorph to apply some changes to the theme.
I went to reboot, and it now it won't load past the htc screen. Even when i try the key combination to put it into recover mode. I didn't install a nandroid backup, and i'd be fine with just completely wiping my phone. help is appreciated.

Crashed T-mobile MDA Vario

Hi, all.
I've been reading a lot through these forums and I've learned a lot, but I don't seem to be able to fix this by myself. I have a Dutch T-mobile MDA Vario (WM5) that's over 3 years old so I'm not worried about voiding warranties.
A few weeks ago, my phone didn't want to boot anymore. I don't know if it's related, but around a week before the crash it had problems with finding the SIM card.
When I boot, it quickly gets stuck at the white background with gray/pink squares and the T-mobile logo. This is the data that's given (after a few factory resets):
IPL 2.21
SPL 2.21
GSM 02.19.11
OS 2.21.2.5
After that, it... just... hangs..., no matter how long I wait.
I tried to reset it to factory defaults (holding the three buttons + power button). The resetting seems to work, but then it gets stuck at the same screen again.
I came along forum.xda-developers.com/showthread.php?t=298613 <-- this thread, and I figured that I might as well try to flash it. I mean, if it doesn't work, well then at least I've tried. As you notice I'm new at this. I'm not afraid of electronics but flashing phone roms is new to me.
I can startup to the bootloader menu (photobutton + power) which tells me:
IPL 2.21
SPL 2.21
So, I've got a G3 device.
When I connect the USB cable to my pc (Win XP SP3), my PC gives the normal sound when a USB device is connected. the MDA nicely adds the text USB to the lower left of the screen. Nice. ActiveSync doesn't recognize it, but that seems to be normal, or so I read.
Following the thread's advice, I've downloaded the needed files and want to install them as ordered. First in the list is the Wizard_Love rom, so I go ahead and try to install it (from c:\XDA\final\). The first download link is broken, but at the end of the tread there is another link( to Wizard_Love_2.26.10.2_WWE_Novii_CF2.rar). The installer is in Spanish(?) but if it can give me back my phone, I'm fine with it. Besides, the readme is in English...
Then, after a short while, it gives me the following error:
ERRORE [300]: STRUMENTO DI AGGIORNAMENTO NON VALIDO
and some more text. I don't speak Spanish, but strumento will translate as instrument and non valido will undoubtedly be 'non-valid'.
It seems somehow that the communication still has some issues. I have just charged the battery, so that's not a problem here.
Do I have a wrong wizard_love rom? If yes, where can I get a proper one?
If not.. What else can I do?
Thanks in advance. You'll be my hero

You could always try to flash the original ROM and see if that gets you past the boot screens.
The installer language translates to Italian, ERROR [300]: INVALID UPDATE TOOL.
Try a different No ID Installer package, not the whole ROM just the No ID Installer.

Thanks! You have no idea how happy you made me..
Your comment on installing the original ROM sent me in the right direction. I went to t-mobile.nl and looked for updates (I shoud've done this much earlier). Where the hard reset failed, the official update worked flawless. I have yet to do the radio update, but I have my phone back! phew, 3 weeks with my old (by now- fossil) Samsung X100 made me realize how much I love this phone.. The QWERTY keyboard to begin with, my agenda, programs...

[Q] microSD damage

I have big problem. Yesterday I bought the 32 gb sandisc microsd card(class 4) and I installed windows phone 7(blackSideSeven v1.13.7401), everything was fine, except marketplace(doesn't work). Today I have decided to install diffrent ROM, I choosed Back to the Future [XBmod-Yuki] [7720 ready]. Rom was installed properly. I added my windows live and gmail accounts, changed data and time, I restarted phone. After that phone didn't work. System was loading, it stopped on "enter pin code" screen. It didn't respond to touch ;/ When i removed sd card touch screen was working, but i got alert "storage card not working" and I coudn't do anything(only emergency call). I installed clean wp7 DFT rom, but I had that same problem. I try to plug scdard to the computer, but it's not detectable ;/ None of the partition, nothing! Is card broken?

- To check the hardware side, take "h2testw". The card should be empty, so the tool could test the complete size.
The background is, that some large cards (16gb, 32gb,...) are fakes. simply wrong labeled.
- Have you take the right order. look: "-Flash the rom with DWI & Set a correct time & date".
dn

I tried to install this rom:
http://forum.xda-developers.com/showthread.php?t=1236027
It works until the reset after zune installed wp7 software update. I had screen when I have to enter a pin, but i couldn't do that. The touch screen didn't work. Even tried WP7 Update Cab Sender to upload DEV_STORAGELOCK_REMOVE.CAB, but it alse didn't work. System couldn't load. When I unplug the usb cable, phone didn't turn on.
My microsd works, but i have to format it(in nokia) evety time when i want to install rom.

Again, i try to install android, but i have that same problem. HD2 doesn't work without usb connection, I can't turn it on ;/ What i should do..?

flamner said:
Again, i try to install android, but i have that same problem. HD2 doesn't work without usb connection, I can't turn it on ;/ What i should do..?
Click to expand...
Click to collapse
Turn phone off. Hold down the volume down key and power at same time until you see a tri colored screen. Connect your usb cable and you will see "usb" in the white section at bottom of your phone screen. Run task29 (search forum) this will erase nand. From there you boot back into the bootloader (tri colored Screen) and you can install WM6.5 or just flash magldr and go with a android rom. Or try WP7 again if you really want to.