Database Users

My SVP M600 phone got stuck at Starting screen

Hi Friends,
My new mobile phone SPV M600 got stuck whil starting showing four lines of messages as shown below.
IPL 2.10.0001
SPL 2.10.0001
GSM 02.07.20
OS 2.10.1.22
Can any one please help me in geting my phone to today's screen.
I also attached the screen shot for reference.

did you try a hard reset ?

Ya I tried both hard as well as soft reset but same screen is stuck again and agian.Can any one please help me in this regard as I am very new to PDA family.

Ok, first things first:
Since you are new to this, are you sure you preformed a hard reset?
It is done by holding power + camera + comm manager buttons (one on the right, two on the left) and pressing with stylus in the reset hole at the same time.
A message should appear asking you to press 'send' (green phone button) to confirm reset.
If this does not help, you may have a serious problem.
Please answer the following:
Is the device fully charged?
Phone will fail to boot if the battery is too low.
Did you install any software right before this happened?
This should have been resolved by hard reset, but just in case I am asking.
Did you change the ROM, attempted CID / SIM unlock?
This could require more serious measures than I can advise on.

I did exactly the same thing which you mentioned.But even then it is stuck at the same screen.
Ya u r right I unlocked my mobile using a software from eBay.The unlock was successfull and I tried to insert T-Mobile sim, it also captured the signal and I was able to make and recieve calls then after that I wantedly switched off the phone and then tried to start it, there got the problem.

Can any one help me in this regard please.

I am having the same problem, but my phone is not sim-locked.

I've got the same problem after attempting smart1_wm6_pp8mb.exe
I'm having the same problem with my G4 QTEK S200:
Attempted to upgrade to WM6 Rom using smart1_wm6_pp8mb.exe
After reboot the phone got stuck at the QTEK Screen
Tried Hard Reset (Camera+Power+Comm+Reset) followed the steps with the same results (bricked)
I also tried re-flashing the rom back to the factory one using RUU_Prophet_220734_2207114_024721_QtekWWE_Ship and ROMUpdateUtility-NoVendorID.exe in Windows Vista with WMDC (Windows Mobile Device Center v. 6.0.6873) and the phone in boot loader mode (tri color screen) with working USB cable, with windows firewall disabled and symantec AV disabled as well, RUU keeps saying error 260 "the update utilitiy cannot connect to your pda phone..." .
Do you think I should try this process using XP instead? No matter what i try i keep getting the error 260
Any help would be greatly appreciated

Got it fixed!
it was definately a Vista issue. once i tried it in XP with ActiveSync it worked like a charm and i got my phone back up and running. also used spb backup and restored all my settings.

ipl/spl screen
i got the same problem with new rom wm6, and the 260 eror, my problem is that i have xp and the activesync does`t connect ...
... means i cant redo the original rom ????
PLEAAASEEE HELPPPP !!

Again My phone SPV M600 got stuck at IPL/SPL screen
Please Can some one advice me how to get my phone back.
I raised the same issue 7 months back after that my phone got recovered automatically and there were no issues till last month. Last month onwards it is again got the same problem and now it is permenantly stuck at that screen what ever you do.

yekanth said:
Please Can some one advice me how to get my phone back.
I raised the same issue 7 months back after that my phone got recovered automatically and there were no issues till last month. Last month onwards it is again got the same problem and now it is permenantly stuck at that screen what ever you do.
Click to expand...
Click to collapse
A rom reinstall on xp solved my problems on that one. retry a couple of times! It may not work the first time! hard reset as well...
Try an official wm5 rom just in case
good luck

Can you please gimme step by step procedure
HI Phil,
I am new to these kind of installations . CAn you please Gimme step by step procedure for ROM installation.

mine is now also stuck, after trying to install new rom. wont connect to active sync either, have i fooked it? tried hard reset etc.
thanks

(with a turned off phone, press and hold camera button then insert USB cable)
then flash provider ROM
RECOVERING FROM ERROR IN STEP 8 WM5->WM6
1. Don't panic
2. Don't panic
3. Unplug the phone
4. Reset with stylus,and keep the Camera Button pressed.
5. A 3 color screen will appear(Bootloader Screen)
6. Connect your device with your PC,and run the NVID(no vendor) WM5 rom.
7. The device will be resetted after RUU(rom update utility)finishes
8. Repeat the WM6 upgrade,from STEP 5..
Click to expand...
Click to collapse
from here http://forum.xda-developers.com/showthread.php?t=310452

hi jay
i seen your post in n00b guys one, i fixed it!!!!, thank you so much, i couldnt remember how to get it to those 3 colours.
thanks again
Colin

Hi Iam unable to get the NVID ROM
Hi,
I am unable to get the NVID ROM. The Rapidshare link that has been provided in the other thread is not working. Can some one tell where can i get the ROM.

collywog19 said:
i seen your post ...
Click to expand...
Click to collapse
no problem mate.
..and yekanth i see what u mean about the dead links. i have the files on my computer at home but i'm posting from my prophet right now, so i can't upload. Try using the "pdaviet temp" from one of the wm6 threads?
(http://rapidshare.com/files/54265407/Prophet_PV_Temp.zip)

Hi Iam able to update the Rom but no use
Hi,
To mention my phone is from orange-UK. I got the orange rom from our FTP site and did the flashing/update what ever you say.But still it is getting stuck at the same IPL/SPL screen. Iam very much worried that I will not get a proper solution for my problem.It will be very grate full if some one resolve my problem.

just seems strange...how did you fix it last time? did it just start working again? A random guess would be that the camera button got liquid spilled on it or is stuck in.
If the camera button is pressed in the phone will go to 3 colour screen every time it is turned on.
It won't do any harm if you try to press/move that button to see if u can "unstick" it, not likely I think but u never know...

Polaris Trapped in Tri-Colour screen

Hi,
Is there anyone out there with their Polaris trapped in Tri-colour (and not running a .Olipro/.OliNex SPL). if so, PM me.

Me
Olipro said:
Hi,
Is there anyone out there with their Polaris trapped in Tri-colour (and not running a .Olipro/.OliNex SPL). if so, PM me.
Click to expand...
Click to collapse
Program stopped in percent screen (in 0%) and don´t run more. After if you unplugged the PDA (an HTC Polaris, of course) and swich on don´t pass of the Tri Color screen and you can read "POLARIS. SPL-1.25.0000.CPLD-2" and in the rigth corner "RUUNBH" but nothing began, no OS or programs, nothing... Any suggestions and help??? Thank You.

Can't flash SPL, Polaris FRA ROM; was bricked...solved,can't flash
Hi Olipro,
last week-end I tried flashing hard SPL v2 on my French Polaris, before planning to flash the new radio 1.64, then bepe's 0.66 ROM.
I spent the first part of Saturday night trying numerous times, recovering, taking battery away, and trying agin - never worked. Then I tried flashing the 1.64 radio, it went up to 99%, then stopped, error message: from then on my Polaris went to boot-loader only, after soft reset or even hard resets. Until dawn I tried to fix this (I'm not a developper, I'm a power user travelling 4 days a week by plane accross Europe). Couldn't fix it.
On Sunday I called a friend of mine who imports HTC and sells the channel: I gave him my Polaris and he took it with him to fix it. Result was very surprising: I had given him your hard SPL v2, and a few nice ROM's from this site, specailly bepe's, as well as all the radio versions listed here for POlaris; well none of all that worked with him, and he could only reflash the official ROM and radio, and return it back to me...(which was very kind as it took him some time).
BUT, overall I'm very frustrated as I'm an early adopter, and I would so much like to try cooked ROM's on this fabulous device.
What do you think I should do? Any idea?
Is there a way to guide me though a custom process or is there a real issue on ALL French ROM's out there? (can't believe that).
Your inputs would really be appreciated.
Thx many, HangLoose.
23:45 > it finally worked !! (I must have been doing something wrong previously, sorry for bothering Olipro).
And thx for enabling us to use best in class cooked ROM's from this site.
I'll be loading bepe 0.67 just now. !!
Regards, HangLoose59

My cruiser not leaving the screen tricolor
My cruiser not leaving the screen tricolor, Tried to replace the original language (Spanish) by the English and upgrade stopped in 14%, dai then not leaving the screen tricolor.
Some hint.

v1zca1n0 said:
Program stopped in percent screen (in 0%) and don´t run more. After if you unplugged the PDA (an HTC Polaris, of course) and swich on don´t pass of the Tri Color screen and you can read "POLARIS. SPL-1.25.0000.CPLD-2" and in the rigth corner "RUUNBH" but nothing began, no OS or programs, nothing... Any suggestions and help??? Thank You.
Click to expand...
Click to collapse
FIXED! at last the problem was I used a SPL for HTC ELF not Polaris and, I don´t know why, that makes OS stopped in an eternal bug... Whem I use again the same Hard SPL for Elf Voilá! Do it! And know all works fine. I promisse: I will never change the BootSplash be sure

v1zca1n0 said:
FIXED! at last the problem was I used a SPL for HTC ELF not Polaris and, I don´t know why, that makes OS stopped in an eternal bug... Whem I use again the same Hard SPL for Elf Voilá! Do it! And know all works fine. I promisse: I will never change the BootSplash be sure
Click to expand...
Click to collapse
I have the same problem My Pc has scrached and now my polaris is blocked to the bootloader
Is some could you help us ?

Diagorn said:
I have the same problem My Pc has scrached and now my polaris is blocked to the bootloader
Is some could you help us ?
Click to expand...
Click to collapse
Hard reset the device and it can take u out of bootloaer mode. To hard reset:
GPS/MESSAGING and INTERNET EXPLORER buttons, and at the same time, use the stylus to press the RESET button at the bottom of your device.
2. Release the RESET button, but continue pressing the GPS/MESSAGING and INTERNET EXPLORER buttons until you see a message on the screen
Release the buttons, and then press SEND on your device to perform the hard reset, or press any other button to cancel the reset.

Hello thanks for your help but I have already tried this

Diagorn said:
Hello thanks for your help but I have already tried this
Click to expand...
Click to collapse
Try with this program do a Hard SPL and tell me how gone

the Elf is a DiskOnChip device, the Polaris is plain NAND.
you can try it, but frankly, I think it's not really the smartest move

Olipro said:
the Elf is a DiskOnChip device, the Polaris is plain NAND.
you can try it, but frankly, I think it's not really the smartest move
Click to expand...
Click to collapse
You are rigth Olipro as always, but I left because I have the experience of used badly and block the PDA until I use again and unblock the machine. Maybe the diferent chip make a kind of bug than only can be fixed with Elf Hard SPL I don´t know but with me works. Let see if is the same with Diagorn

could be a side-effect, but the file should be blocked from flashing anyway.

i have the problem too. waiting for the solusion

Olipro said:
could be a side-effect, but the file should be blocked from flashing anyway.
Click to expand...
Click to collapse
Curiously Elf SPL unblock the flash and I don´t know why Anyway I stopped flashing anymore because I don´t want have the same problem again. Only I explain what happend to anyone that can have the same problem and attach the Elf Hard SPL if they want use and probe

BT Problem
The BT LED styed ON and after hardware reset (removing the battery, the reset button wasn't working) only the bootloader screen. It revived after I flashed the Radio ROM. And what bugs me is that BT button remains ON in TouchCommander, but NO BT. any ideas???

BT Problem
After synchronising with the PC i noticed the BT LED goes OFF ...
BTW
HardSPLv2.2
ROM 1.28Aserg.1WWE
RADIO 1.64.08.21

Cruise stuck in 3-color screen
Hi,
My Cruise just frooze, during GPRS synch with Exchange server. Soft reset and hard reset do not work anymore. If I take out the battery, and then switch on the device it stops in the 3-color screen. BT light stays on.
I have not made any changes to my Cruise, only added a 8 Gb SD card.

v1zca1n0 said:
Program stopped in percent screen (in 0%) and don´t run more. After if you unplugged the PDA (an HTC Polaris, of course) and swich on don´t pass of the Tri Color screen and you can read "POLARIS. SPL-1.25.0000.CPLD-2" and in the rigth corner "RUUNBH" but nothing began, no OS or programs, nothing... Any suggestions and help??? Thank You.
Click to expand...
Click to collapse
me too...somebody help !!! sorry my english

Strangely enough it works!!!
v1zca1n0 said:
Try with this program do a Hard SPL and tell me how gone
Click to expand...
Click to collapse
I was really frightened when my TC got stuck in Tri-Colour screen. MY Polaris came to standstill, trapped in.
Over and over ROMUpdateUtility.exe shows ERROR [262 or 284]: UPDATE ERROR while trying update.
And only this strange RUU gave me other ERROR [296]: UPGRADE ONLY that helped me to quite out the three-color screen and installed new radio successfully.

Urgent help: HTS P3300 stuck up

Dear All,
Please urgent help required.
my HTC P3300 (Artemis) stuck up when i was trying to start it up. when i use to turn my cell on, i goes to the starting screen shows the following numbers and then stuck up.
IPL 3.07.0001
SPL 3.07.0000
GSM 02.69.90
OS 3.7.0.0
the screen does not move after that. i tried soft reset through the reset button but result is the same.
i also tried hard reset and when i puch the green phone button to proceed, a message come "FORMAT FAILED" and the phone stucks up.
i am quite a lot of problems since i have upgraded to WM6 from WM5 last week.
i am quite sucked with this problem. not been able to use my set since yesterday.
please also note that my HTC was not syncing with my PC since i have upgraded to WM6.
PLEASE HELP URGENTLY.
Nomi

You must upgrade :
-Remove SD-Card
-Remove Sim-Card
-USPL
-Upgrade new ROM

thank. i got through to install wm 6.1.
can any one please tell me which is the most stable ROM for 6.1 or 6.5
which one is better for my HTC artemis.
please post link to the ROMs

I'm using two roms :
Shady313-23081R1 : http://forum.xda-developers.com/showthread.php?t=546805
dheewatara-s 23075B1 : http://www.pdamobiz.com/forum/forum_posts.asp?TID=255901&PN=1

same problem..pls help
i have same rom and ratio with u nomi...but my problem still occur...
where do u get the USPL eventually?

[Q] hermes 8525 freezes

well my phone after i flashed and installed wm 6.5 it was working totally fine, but this morning i turned it off and then on and it totally freezes at the startup screen and never loads windows. what i can do?
i'll appreciate any comments

i have then same problem switches on displays, disigned for windows mobile 6.5.5 then freezes

Yeah many ppl has this issue... be sure to flash first the att stripped att stock rom then hard reset then boots then reflash the custom rom then hardreset then try again to use th rom maybe it works ok now

I have the same problem
but I have the same problem. I bought a second hand phone and also freezes on the welcome screen and to make the rom? I need it so I can re-flash the windows

I have problem with my tytn, i was traying 7-8 rom of win mobile 6.1 or 6.5 but no help, my htrc cant find nework or when he find network he was online 1 hour and after hat he he offline in phpne mode, what is a problem, radio, rom or... ????

miljan017 said:
I have problem with my tytn, i was traying 7-8 rom of win mobile 6.1 or 6.5 but no help, my htrc cant find nework or when he find network he was online 1 hour and after hat he he offline in phpne mode, what is a problem, radio, rom or... ????
Click to expand...
Click to collapse
try to upgrade radio version on your device !! you can find Radio Rom Wizard in http://forum.xda-developers.com/showthread.php?t=300713 or at http://forum.xda-developers.com/showthread.php?t=268031

i cant start update proces always error 260 or 262

Jasjam Freez on i-mate logo
Dear Friends
my jasjam stop on first screen(i-mate Logo) . I did soft and hard reset again and again but nothing!i remove battery and sim card along the night but nothing again.pls help me what's problem
Thnkas and goodluck

Batman1351 said:
Dear Friends
my jasjam stop on first screen(i-mate Logo) . I did soft and hard reset again and again but nothing!i remove battery and sim card along the night but nothing again.pls help me what's problem
Thnkas and goodluck
Click to expand...
Click to collapse
probably you need reflash again your device with Original Shipped ROM

JasJam Freez on Logo
Dear Rahman
sorry for my bad english.Thank u for ur reply.jasjam freez on the first page!it mean i can not connect it to PC via active sync because it no load to windows!PC can not detect device!so how can i fix this problem without a PC connection ?

Skin Is Not Loaded :(

hi my friends.
I changed my jasjar's tomal 6.1 rom to Original WM5 for sell my phone
but after changing rom, i have a terrible problem.
when i closed the battery for change the simcard and turn it on. when the windows logo appears a blue screen showed and the gsm led begin to work (blinker).
after several soft resets the windows starts and ready to work but when i press the power button to standby the device (sometimes) for turn on the device (after standby) the screen didn't appear.!!
i'm very upset
after that i flashing the radio to newer version (1.18) and flash back to WM6.1 TOmal , WM6 , ... but i still have this problem.
in the tomal's wm6.1 rom (TML_v82_WM61_19960) before the problem shown an error appears under the windows logo > The Skin Is Not Loaded < and after that a black or blue screen appears and nothing...
please help me to fix it.
thanks friends

No Answer ?!
Really ?!
it's very important for me.
plz help

Only thing I can think of is to doc-format (mtty). And then flash ROM again. Then make sure you Hard Reset.

-Jonny- said:
Only thing I can think of is to doc-format (mtty). And then flash ROM again. Then make sure you Hard Reset.
Click to expand...
Click to collapse
What is the mtty ? doc-format ?
How can i do it ?
tnx for attention

DOC format

-Jonny- said:
DOC format
Click to expand...
Click to collapse
wow , thanks for guide me.
as your experiences , this work would be harmful for the device ?
thankx

It's not harmful - basically it totally wipes the device removing everything (including garbage). So you will, of course, need to flash a ROM afterwards.