Related
Hi there! I have a problem after install MAGLDR :/ I connected my HD2 to computer with ActiveSync, runned ROMUpdateUtility from computer, on my phone there was a tricolour screen, then self-reset and phone is freezing on white HTC LOGO. I tried to turn off my phone, remove battery... I'm also turning my phone on with press vol down + power - I have 3 colour screen and now what? PLEASE HELP!
Connect your HD2 to your laptop/pc... boot it while pressing volume down.. wait untill it says usb in the bottom of your screen. Now you can flash HSPL 2.08 and flash a custom or original rom.
I had the same.. gonna stick with RAM roms untill this is nand stuff is sorted out
I have the same problem... but after reflash HSPL 2.08 there will be no change. Could not start the machine.
How can flash rom from pc without booting the machine?
I couldn't understand "Now you can flash HSPL 2.08 and flash a custom or original rom." the second step ...
solved!
I had the same problem.
The issue it's the radio.
install 2.15.50.14
http://www.multiupload.com/QP0IWGY42F
Hi,
After installing hspl 2.08 and then going on to install magdlr, when successful and rebooting it just stayed on the HTC logo screen. It wont reset but it will enter into bootloader. How exactly do i fix this. I tried reinstalling HSPL but it is still stuck on that screen. How would i change this 'problematic radio'?
I relly need to fix my phone so any help would be appreciated! Thanks
sexyseamus said:
Hi,
After installing hspl 2.08 and then going on to install magdlr, when successful and rebooting it just stayed on the HTC logo screen. It wont reset but it will enter into bootloader. How exactly do i fix this. I tried reinstalling HSPL but it is still stuck on that screen. How would i change this 'problematic radio'?
I relly need to fix my phone so any help would be appreciated! Thanks
Click to expand...
Click to collapse
Download a compatible radio (eg 2.15.50 in post above), boot to bootloader (switch off, vol down + power on (keep holding vol down until it boots), connect to pc and when usb shows on screen run the CustomRUU.exe in the radio download. (if there isn't one included you can take any one from a custom wm rom). You flash the radio the same way that you flash a rom.
Thanks for the quick response! I have tried doing this before and just tried the custom RUU posted above but when i run it where it says the image thats on the phone it is blank. Even so i click to update it and both on the phone and pc it stays at 0%. I don't know what to do!
sexyseamus said:
Thanks for the quick response! I have tried doing this before and just tried the custom RUU posted above but when i run it where it says the image thats on the phone it is blank. Even so i click to update it and both on the phone and pc it stays at 0%. I don't know what to do!
Click to expand...
Click to collapse
Are you sure you have HSPL installed properly. In bootloader mode, check the spl version - it should show as 2.08.hspl, not 2.08.0000 or any other hspl version.
In bootloader mode it says SPL 2.08.0000? When installing it i did select the HSPL 2.08?? What should i do? Thanks
sexyseamus said:
In bootloader mode it says SPL 2.08.0000? When installing it i did select the HSPL 2.08?? What should i do? Thanks
Click to expand...
Click to collapse
I had your problem and for some reason when I first ran hspl the first time and put 2.08 on my phone it said it worked but it didn't actually do anything.
Just reinstall 2.08 HSPL on your phone and then run MAGLDR.
Similar Scenario
I installed 2.08.HSPL - confirm at boot loader screen
I installed MAGLDR 1.13 with success
Flashed HD2_Core_Droid_Desire_HD_V1.5_NAND_ONLY_LEO1024_TMOUS to my phone with success
Phone worked fine for about a day and a half and froze up
Pulled battery and restarted to white screen
I can't seem to roll back the SPL, reinstall the MAGLDR, or install a different radio.
ROM Update Utility appears to start to work and phone restarts and I get an error message that the image is corrupt.
Any ideas?
I flashed MAGLDR from DFT_LEO70_RELEASE and now i'm stuck on bootscreen and can't get into MAGLDR
tried task29 then MAGLDR again but still the same prob.
any help?
thanx in advance
ahmedsalem89 said:
I flashed MAGLDR from DFT_LEO70_RELEASE and now i'm stuck on bootscreen and can't get into MAGLDR
tried task29 then MAGLDR again but still the same prob.
any help?
thanx in advance
Click to expand...
Click to collapse
turn off your phone, press and hold power button while you turn on your phone until you see the MAGLDR menu.
waichai said:
turn off your phone, press and hold power button while you turn on your phone until you see the MAGLDR menu.
Click to expand...
Click to collapse
Tried this but nothing happens
it remains stuck on bootscreen
ahmedsalem89 said:
Tried this but nothing happens
it remains stuck on bootscreen
Click to expand...
Click to collapse
do you have 2.08HSPL on your phone?
I'm pretty Sure i have hard spl
but i'm not sure what version
ahmedsalem89 said:
I'm pretty Sure i have hard spl
but i'm not sure what version
Click to expand...
Click to collapse
hold the volume key down while turn on your phone, then you will see the tri-color screen. you will know what hardspl you have.
it written
spl-1.42.hspl xe
0x05
CotullaHSPL 0x50
ahmedsalem89 said:
it written
spl-1.42.hspl xe
0x05
CotullaHSPL 0x50
Click to expand...
Click to collapse
you have hardspl on your device, but it's not 2.08hspl. you need to update to 2.08hspl. Otherwise MAGLDR won't work with your current 1.42hspl.
Downloaded Hspl3 and flashing now but there r 2 options
2.08.0000
and
2.08.hspl
should i choose the second one
ahmedsalem89 said:
Downloaded Hspl3 and flashing now but there r 2 options
2.08.0000
and
2.08.hspl
should i choose the second one
Click to expand...
Click to collapse
2.08hspl, NOT 2.08.0000
Alright flashed hardspl and it booted directly into MAGLDR
now i'll continue installing WinPho 7
I really can't Thank u enough
ahmedsalem89 said:
Alright flashed hardspl and it booted directly into MAGLDR
now i'll continue installing WinPho 7
I really can't Thank u enough
Click to expand...
Click to collapse
you are welcome. enjoy WP7
Hi guys,
i have the same problem. I flashed MAGLDR from DFT_LEO70_RELEASE and actually i still can't get into MAGLDR boot (i have the white screen).
Let me resume the tasks that i have done:
1) i'installed 1.66.408.1 (76641) ITA ROM;
2) with HSPL3_PKG.exe i installed 2.08HSPL;
3) i installed the 2.15.50.14 radio;
4) i installed (i suppose) the MAGLDR112 from the DFT_LEO70_RELEASE;
When the HD2 reboot i press the power button, in order to have the MAGLDR menu, but i always have the splach HTC white screen.
Please help me.
thanx in advance
Niccolo
niccolog71 said:
Hi guys,
i have the same problem. I flashed MAGLDR from DFT_LEO70_RELEASE and actually i still can't get into MAGLDR boot (i have the white screen).
Let me resume the tasks that i have done:
1) i'installed 1.66.408.1 (76641) ITA ROM;
2) with HSPL3_PKG.exe i installed 2.08HSPL;
3) i installed the 2.15.50.14 radio;
4) i installed (i suppose) the MAGLDR112 from the DFT_LEO70_RELEASE;
When the HD2 reboot i press the power button, in order to have the MAGLDR menu, but i always have the splach HTC white screen.
Please help me.
thanx in advance
Niccolo
Click to expand...
Click to collapse
I don't know exactly what u did wrong maybe u did the right steps but in a wrong order?
but u can try to do a task29, make sure u have 2.08.HSPL and 2.15.50.15 Radio then flash MAGLDR again it should work
ahmedsalem89 said:
I don't know exactly what u did wrong maybe u did the right steps but in a wrong order?
but u can try to do a task29, make sure u have 2.08.HSPL and 2.15.50.15 Radio then flash MAGLDR again it should work
Click to expand...
Click to collapse
More detail:
after the HSPL3_PKG.exe (actually i have this scenario:
PB81100 SS-BC
SPL-2.08.HSPL 8G XD
0x02
CotullaHSPL 0x20
i did a task 29, after that i installed tha last radio (2.15.50.14) and finally MAGLDR112.
When the device reboot i press the power button for 2-3 minutes but i always have the white screen
I was thinking that the problem could be that i have HD2 ProThree (in the hardware information i see in the RAM section 320MB and not 576MB); remember that i have the 2.15.50.14 radio but i haven't enabled the 576MB (RAM).
Any suggestion?
Thanks in advance.
niccolo
I have the same problem. Have you found any solution?
Same problem here!!
Hi Guys I have a factory HD2
ROM: 3.14.405.0 (04666) WWE
Radio Ver: 2.15.50.14
SPL: 3.03
Would i be able to flash my HD2 with the HSPL3 - i press the Vol Key down and the SPL ver I'm seeing is SPL-3.03.0000 XE ?
If not able to flash with this HSPL3, would I have to downgrade or use another soft? What should i do to continue with the whole process here to install WP7?
Thanks,
Alexandros
loumposa said:
Hi Guys I have a factory HD2
ROM: 3.14.405.0 (04666) WWE
Radio Ver: 2.15.50.14
SPL: 3.03
Would i be able to flash my HD2 with the HSPL3 - i press the Vol Key down and the SPL ver I'm seeing is SPL-3.03.0000 XE ?
If not able to flash with this HSPL3, would I have to downgrade or use another soft? What should i do to continue with the whole process here to install WP7?
Thanks,
Alexandros
Click to expand...
Click to collapse
you will have to downgrade by installing an earlier version of your rom. HSPL3 only supports up to SPL 2.10.
jase33 said:
you will have to downgrade by installing an earlier version of your rom. HSPL3 only supports up to SPL 2.10.
Click to expand...
Click to collapse
Hi jase33,
I've got the same ROM/Radio version (and same version of SPL). Will try to downgrade the ROM to an earlier version. Would love to give WP7 a spin!
What I would like to know is whether flashing back the manufacturers ROM would revert the SPL version to 3.03
Many Thanks in advance
hi All
after installing ROMupdateutility.exe to my HD2 ,while restarting to get the black screen that have 9 choice but i didnt get this black screen and its stopped in HTC logo white screen,
whats wrong with this and what i have to do?
thanks alot.
I f you install no rom that's a bit normal
When you start your phone, push the power button and hold it until you get the menu.
i didnt get it yet, its 5 minutes
thanks,
What version of HSPL do you have on your device. Magldr only works with 2.08 as per all instructions in many threads.
Beany69 said:
What version of HSPL do you have on your device. Magldr only works with 2.08 as per all instructions in many threads.
Click to expand...
Click to collapse
its 2.o8
Sent from my HTC Desire using XDA App
Problem with maglder
Hi
I am trying to install Magldr on my HTC HD2, SPL 2.08, however i am getting the following error message everytime MagLdr (RomUpdateUtility) restarts my phone to upload the new version,
"ERROR [266]: UPDATE ERROR
The update utility cannot get response from your PDA phone. Please check that your USB cradle/cable is connected properly between the PC and your PDA Phone. And also check your PDA Phone."
Dont know why it shows this message, I checked all the connections, the SPL shows connected to USB, my Windows 7, 64bit also dectects it, but I am still getting this message. please help
Have you got SPL 2.08 or HSPL 2.08? The rom update utility won't run unless you've got HSPL installed.
Beany69 said:
Have you got SPL 2.08 or HSPL 2.08? The rom update utility won't run unless you've got HSPL installed.
Click to expand...
Click to collapse
thanks Beany69, Not sure, I am new to this thing, right, let me tell you extactly what it shows when I start my phone in boot mode or what ever its called i.e. when I press the downkey with green button
"PB81100 HX-BC
SPL-2.08.HSPL 8G XE
0x05
CotullaHSPL 0x40"
is this HSPL, if not how do I upgrade this it the required HSPL., please
and when I run the RomUpdateUtility.exe on my pc, it checks the current version displays it as "Miri"
Can someone please help. I went to the sticky thread to get all info to install android
http://forum.xda-developers.com/showthread.php?t=893948
My system information is:
ROM Version 3.14.531.1
Radio Version 2.15.50.14
I started with loading HSPL on my phone being my radio is 2.15.50.14 which is a requirement for HSPL4. When I install HSPL I connect my phone via sync and the computer detects it and runs through the install. It even shows the "We Hacked It" screen on my phone as its supposed to but when I hold volume down and the power button my phone doesn't show HSPL 2.08, I only see SPL-2.10.0000 8G XE
When I tried to continue loading Magldr from there I get an error and I can't go any farther. Can someone please help, how do I get HSPL to actually load which will allow me to load Magldr.
Thanks
O
What error do you get?
Try manually going into bootloader by holding down the Volume Down button and then powering on phone (still holding volume down).
Then plug in USB and load up MAGLDR DFT flasher.
Thanks TheATHEiST
However I can't get to the bootloader page. I corrected my previous post when I hold the volume button and power button down I get the four color screen that only shows the SPL version I have. I don't know why the HSPL flash doesn't work.
I recently bought a second hand HTC HD2, and after asking via email the seller said he has previously flashed an Android rom, and he says he's rooted it. However he hasn't told me whether it was installed by NAND or SD etc, so I'm not sure if it has HARDSPL 2.08 which is what I need to install the Android ROM I want. I don't want to install hardspl 2.08 again because it might brick my phone? so any way to check for hardspl 2.08? My phone is currently running WM 6.5
Also, how do you check the radio version on WM6.5, because I'll also need to make sure my radio rom is compatible with the android rom..
and if I do install the same radio rom twice will it brick my phone?
thanks
phone down
hold voldown
tap n release power
keep holding voldown
when stripey screen appears, there is a line marked spl.
as for radio, when you start booting, a screen appears with small text in teh lower corner, R,G,D, thats the rom radio and protocol version
however for simplicity, just flash them, they take seconds to flash.
put phone into bootloader
connect to usb
run hspl4 - choose 2.08.hspl
phone back into bootloader
connect usb
flash radio 2.15.50
good to go.
thanks, but I thought if you installed hspl twice then you'll brick your phone, and I wasn't so sure about the radio part. So it's safe to install HSPL and the radio rom again?
yep, dunno where you heard that, but maybe its regarding a different phone?