Database Users

Please need help !!!

Hi, i was going to upgrade to ArtemisV9 from Artemis v8. Had some stability problems with v8 so I thought making task 28 with MTTY. When I tried to flash artemis from the bootloader after that , the bar stayed at 0% so I had to cancel. Have tried flashing both via USB and from the storage card, but the progress bar never goes past 0%. When I start the phone it is stuck with the picture with hTc. Please help

task 28 or 29?
as far as i know task 29 also removes the radio. try flashing a radio rom first and after flash the rom.

Ultimaex said:
task 28 or 29?
as far as i know task 29 also removes the radio. try flashing a radio rom first and after flash the rom.
Click to expand...
Click to collapse
Thanks, but i have tried to flash the radio again but i will not work. I meant task 29. When I try to flash radio/rom the black screen with hTc and progresbar appears but i will not start. When I start the telephone the wihite screen with green hTc stucks, if I press vol down and reset the bootloader starts. Active sync can´t connect with the telephone, is this necesarry if you flash from bootloader?

it's neccessary full stop! there's your issue. This is how I flash the HD2:
1. Task29 & radio
2. Boot into bootloader
3. flash ROM once it says 'USB'
4. boot first time
5. hard reset
6. set phone up
All works fine

EddyOS said:
it's neccessary full stop! there's your issue. This is how I flash the HD2:
1. Task29 & radio
2. Boot into bootloader
3. flash ROM once it says 'USB'
4. boot first time
5. hard reset
6. set phone up
All works fine
Click to expand...
Click to collapse
I renamed the radio to LEOIMG.nbh and put it on my storage card, tried mtty again and then tried to enter bootloader, a white screen with Loading appears but gets stuck. I tried to renamed artemis to LEOIMG.nbh with the same result. If I tries to flash with USB, the black screen with progressbar appears and gets stuck at 0%. I have tried to flash stock rom with same result both with the exe file and I tried to extreact the nbh file and placed it on the storage card. Any suggestions how to get my phone to work.

Please
No one that have any suggestions? Is it possible that I have crashed the phone and that its not possibly to get any rom to work? I have Hspl so the warranty is gone.

with phone in bootloader mode.
what spl does it show exactly?
when you connect the usb cable, the word serial changes to usb, correct?
is your phone provider locked, and if so do you have the correct provider stock rom available?
do you have file extensions visible on your pc? (it isn't unknown for people to rename the nbh to "leoimg.nbh.nbh" by mistake.)
when it sticks on the white screen are there any numbers at the bottom of the screen?

samsamuel said:
with phone in bootloader mode.
what spl does it show exactly?
when you connect the usb cable, the word serial changes to usb, correct?
is your phone provider locked, and if so do you have the correct provider stock rom available?
do you have file extensions visible on your pc? (it isn't unknown for people to rename the nbh to "leoimg.nbh.nbh" by mistake.)
when it sticks on the white screen are there any numbers at the bottom of the screen?
Click to expand...
Click to collapse
Thank you, Im realy desperate.
SPL-2.08.0000 8G XE
Yes when Iconnect the serial changes to usb.
No it´s not provider locked
No, the filename is LEOIMG.nbh (if I take away .nbh it only says file and nothing happens from bootloader)
Now I renamed Artemis v9 to LEOIMG.nbh started the bootloader. A White screen with blue text Loading ... nothing more

ok, so you have spl 2.08.0000 which isn't hspl so the cooked roms don't work. . . and spl 2.08 won't let itself be downgraded by stock rom flash so they won't work.
connect to usb in bootloader
run hspl2
choose 2.08.hspl NOT 2.08.0000 in the list.
return to bootloader mode
should now say spl 2.08.hspl
flash your rom over usb
if it doesn't boot check radio

samsamuel said:
ok, so you have spl 2.08.0000 which isn't hspl so the cooked roms don't work. . . and spl 2.08 won't let itself be downgraded by stock rom flash so they won't work.
connect to usb in bootloader
run hspl2
choose 2.08.hspl NOT 2.08.0000 in the list.
return to bootloader mode
should now say spl 2.08.hspl
flash your rom over usb
if it doesn't boot check radio
Click to expand...
Click to collapse
Thank you for taking time. You realy saved my day. Now I feel like a complete idiot. Thanks again.

no worries. you can sit back and breathe again now.

stuck after installing MAGLDR while installing NAND

oh i got a serious problem
after I install MAGLDR 1.11 my HD2 it succeed and did reboot and then it did stuck in white screen with hTC green log.
What to do? It cannot connect it to the sync with computer when it is with this screen. I tried so many time to reset it (with pressing long the power bottom) but I didn’t get MAGLDR 1.11 boot menu, so I cannot proceed to the next step which is installing NAND
My HTD looks like with no operating system only with white screen with hTC green log, What to do? Any help PlZzZzZzZzZzzzz?

Milan Geek said:
oh i got a serious problem
after I install MAGLDR 1.11 my HD2 it succeed and did reboot and then it did stuck in white screen with hTC green log.
What to do? It cannot connect it to the sync with computer when it is with this screen. I tried so many time to reset it (with pressing long the power bottom) but I didn’t get MAGLDR 1.11 boot menu, so I cannot proceed to the next step which is installing NAND
My HTD looks like with no operating system only with white screen with hTC green log, What to do? Any help PlZzZzZzZzZzzzz?
Click to expand...
Click to collapse
Did you try reading the flashing instructions. Refer to the Flashing NAND Android rom link in my signature. The problem is that you probably have the wrong radio. Also please don't start new threads to ask questions when threads already exist. This thread will soon be moved.

Milan Geek said:
oh i got a serious problem
after I install MAGLDR 1.11 my HD2 it succeed and did reboot and then it did stuck in white screen with hTC green log.
What to do? It cannot connect it to the sync with computer when it is with this screen. I tried so many time to reset it (with pressing long the power bottom) but I didn’t get MAGLDR 1.11 boot menu, so I cannot proceed to the next step which is installing NAND
My HTD looks like with no operating system only with white screen with hTC green log, What to do? Any help PlZzZzZzZzZzzzz?
Click to expand...
Click to collapse
remove battery
enter HSPL via bootloader (have you got HSPL 2.08)??
(long press volume down + briefly press power button)
btw wrong post here mate

Moved to HD2 Android Q&A and General

I got the same problem with SPL 2.08.HSPL, oficial ROM 3.14.412.2, RADIO 2.15.50.14. I've tried everything, wasting tons of hours, reinstaling diferent versions of MAGLDR and so, but unfortunatelly I've had to back to the oficial ROM.
Help Please!

sanroman said:
I got the same problem with HSPL 2.08, oficial ROM 3.14.412.2, RADIO 2.15.50.14. I've tried everything, wasting tons of hours, reinstaling diferent versions of MAGLDR and so, but unfortunatelly I've had to back to the oficial ROM.
Help Please!
Click to expand...
Click to collapse
Are you sure your spl version is 2.08.hspl and NOT 2.08.0000?

Completly!. SPL-2.08.HSPL as stated on tricolor screen. Thanks for the response.

And you also sure of the radio version? Really strange that it doesn't work. Where exactly does it get stuck, is it after or during the install of magldr?

Absolutely sure. All info is the one shown in the device. MAGDLR installs perfectly at 100%, it stucks at reboot, it shows the white htc screen and that's all, the device doen't work any more and I've to reinstall oficial rom.

Really weird - first one I've seen where 2.08.hspl and 2.15.50 radio doesn't get magldr to boot. Not sure what else to suggest apart from perhaps doing a Task29 to format the NAND area and starting all over.

I've tried one again, including task29 at begining. And i'm still the same, MAGLDR doesn't show the menu and stucks at login htc screen. I want to cry!. I'd appreciate any idea. All DFT needs MAGDLR, I need smthing that doesn´t need MAGDLR, is it possible?.

There are the Android versions that run off sd card which run as a dual boot with winmo.

sanroman said:
I've tried one again, including task29 at begining. And i'm still the same, MAGLDR doesn't show the menu and stucks at login htc screen. I want to cry!. I'd appreciate any idea. All DFT needs MAGDLR, I need smthing that doesn´t need MAGDLR, is it possible?.
Click to expand...
Click to collapse
Check your radio version - I had the same issue but after updating my radio everything was fine!

sanroman said:
I've tried one again, including task29 at begining. And i'm still the same, MAGLDR doesn't show the menu and stucks at login htc screen. I want to cry!. I'd appreciate any idea. All DFT needs MAGDLR, I need smthing that doesn´t need MAGDLR, is it possible?.
Click to expand...
Click to collapse
well, maybe its kinda "stupid" question, but do you press the power (red) button while booting? I mean, you have to press it long enough, till the magldr menu comes up..

Believe me that i've tested that way, and another ones, so as to get it work, but no luck.

I got stuck on the htc logo screen while trying to boot to a previous NAND version I had. I flashed it right away for the first time but now I jsut got stuck on the logo screen an than its reboots, again and again. any help as now I stuck with the MJD CyanogenMod which I have few problams with and I am trying to boot again to hd2one CyanogenMod .

mikelt89 said:
I got stuck on the htc logo screen while trying to boot to a previous NAND version I had. I flashed it right away for the first time but now I jsut got stuck on the logo screen an than its reboots, again and again. any help as now I stuck with the MJD CyanogenMod which I have few problams with and I am trying to boot again to hd2one CyanogenMod .
Click to expand...
Click to collapse
Format the sd card. I would also suggest flashing back to a winmo rom and then starting over.

chpelle said:
Check your radio version - I had the same issue but after updating my radio everything was fine!
Click to expand...
Click to collapse
Rerereinstalled and no luck. Why me?

I have the same problem. I have checked the radio and everything to make sure it is fine but still getting stuck at htc screen??
Can someone help me please
Thanks

cwm recovery
flashed cwm recovery update for hd2 no my phone wont charge nor register when plugged into the computer. is there a way to fix this

[Q] Bricked?

So guys I need help! I can't boot my phone! I can boot in to HSPL but that's about it. I can't boot in to MAGLDR. I tried running a Task29 but it just stays at 0%.
I've tried flashing MAGLDR and it's the same as the Task29... stays at 0%. Has my phone been bricked? Any help appreciated. I've tried flashing a stock ROM from SD and renaming the .nbh to LEOIMG.nbh but the first time I did it and it says to press power to confirm you want to flash it the phone just rebooted to the WSOD. Seems as though that changed my HSPL to HSPL.2.08.0000 now too instead of .HSPL. now all I get when I have the SD card in and boot to HSPL then when it boots to the grey coloured screen it just says "Loading...".
Is there anyway I can get my phone working again? Thanks.

Try to flash WM 6.5 1.66 version (or atleast the one below the most recent) trough SD method.
My kid brother had the same thing, the newest ROM (from HTC website) didnt work cause it gave a error.
If you keep getting some red error status while doing the SD flash, it might be bricked.
After a few tries with the SD method we were able to flash stock spl and such, but still the phone wasnt oke (but oke enough to send it for repair).

Skellyyy said:
So guys I need help! I can't boot my phone! I can boot in to HSPL but that's about it. I can't boot in to MAGLDR. I tried running a Task29 but it just stays at 0%.
I've tried flashing MAGLDR and it's the same as the Task29... stays at 0%. Has my phone been bricked? Any help appreciated. I've tried flashing a stock ROM from SD and renaming the .nbh to LEOIMG.nbh but the first time I did it and it says to press power to confirm you want to flash it the phone just rebooted to the WSOD. Seems as though that changed my HSPL to HSPL.2.08.0000 now too instead of .HSPL. now all I get when I have the SD card in and boot to HSPL then when it boots to the grey coloured screen it just says "Loading...".
Is there anyway I can get my phone working again? Thanks.
Click to expand...
Click to collapse
hope this helps
http://forum.xda-developers.com/showthread.php?t=591314
http://forum.xda-developers.com/showthread.php?t=668347
dont forget to click thanks

Lol, guys all I did was hold down the reset button on the back and it turned back on. HAPPY!
Though, I want to run a Task 29 but it's still stuck at zero.
Oh well, I have a working HD2!

Skellyyy said:
Though, I want to run a Task 29 but it's still stuck at zero.
Click to expand...
Click to collapse
Because you don't have hspl you removed it by SD card stock flash.

samsamuel said:
Because you don't have hspl you removed it by SD card stock flash.
Click to expand...
Click to collapse
I didn't flash the stock ROM. I didn't do anything, just held the red button in. It keeps acting up now. Think it's time to sell and buy a new one.

Skellyyy said:
I didn't flash the stock ROM. I didn't do anything, just held the red button in. It keeps acting up now. Think it's time to sell and buy a new one.
Click to expand...
Click to collapse
really? I think you did...
Skellyyy said:
So guys I need help! I can't boot my phone! I can boot in to HSPL but that's about it. I can't boot in to MAGLDR. I tried running a Task29 but it just stays at 0%.
I've tried flashing MAGLDR and it's the same as the Task29... stays at 0%. Has my phone been bricked? Any help appreciated. I've tried flashing a stock ROM from SD and renaming the .nbh to LEOIMG.nbh but the first time I did it and it says to press power to confirm you want to flash it the phone just rebooted to the WSOD. Seems as though that changed my HSPL to HSPL.2.08.0000 now too instead of .HSPL. now all I get when I have the SD card in and boot to HSPL then when it boots to the grey coloured screen it just says "Loading...".
Is there anyway I can get my phone working again? Thanks.
Click to expand...
Click to collapse
Just so you know, when you start a stock rom sd card flash, the first thing it does is reset the spl, THEN it tries to flash the rom, two seperate events, (the phone even restarts in some instances between changing spl and starting the rom flash) so even if the flash fails, or doesnt even start, theres a good chance spl has already been removed.
(side note for info - This situation is most likely to happen when flashing stock from sd card when hspl is installed, because the rom doesnt get rejected at first because hspl is there, but after the spl is reset and teh phone reenters bootloader, it no longer accepts the rom, because hspl is gone, so the phone is temporarily locked up with no hspl and no working rom.)
So, you now have stock spl 2.08.0000 and a non working rom.
enter bootloader,
run hspl (new hspl4 link in my sig)
choose 2.08.hspl
re enter bootloader
flash magldr (just to be sure its there)
if you need to, make sure your radio is high enough version (if you have tmous forget this, if its a regular it needs to be in the 2.10.50 or so version or higher)
from power off, start the phone, as the very first splash screen changes to the black magldr screen, start pressing power, untill the menu items appear.
Job done.
Oh and the line "....I have the SD card in and boot to HSPL ......" makes no sense. You are booting to bootloader. its still bootloader whether it has spl or hspl. Your terminoligy will confuse you.

Well I highly doubt I did. Maybe it just updated the HSPL but that's all. Didn't even get rid of MAGLDR on my phone! When I held in the reset button, it booted straight to MAGLDR.
Maybe mine was just a fluke!

lol thats what i said, in a long winded way. when you run an sd card flash the first three or four seconds it loads the spl from the rom on the sd card, thus removing hspl.
(or in your incorrect words 'Maybe it just updated the HSPL but that's all' - correct, it 'updated' HSPL back to stock SPL)
but hey,its sorted, so no problem.

It's still HSPL though? It's just the previous version that's .0000 instead of .HSPL or am I completely off? Do I need to flash HSPL.2.08.HSPL again or can i just keep it .0000?

Lol I'm stupid. Sorry, realise now what you're saying now that I've looked at the SPL properly. So do you suggest I flash HSPL now?
Sent from my FutureShocks HD2 MIUI using XDA App

Lol,
One simple rule...
If it ends 0000 it is STOCK
If it ends .hspl it is hspl
Yes, run hspl.exe again, choose 2.08.hspl

Haha well atleast I've learned now. I don't even read the first part which just said SPL. Fail. If I flash HSPL again do I need to flash MAGLDR again?
Sent from my FutureShocks HD2 MIUI using XDA App

possibly, cos teh same sd card flash that wiped hspl could have also removed the second splash screen memory area, which is where magldr lives. deopends how far thru the flash it got before it stopped.
easy to tell tho, let it boot, if you see the black magldr screen appear when the first boot screen vanishes,, quickly press power and it will stop there and show the magldr menu, if it hangs without showing teh magldr screen, magldrs not there, and you pull the battery, into bootloader, flash magldr.

samsamuel said:
Lol,
One simple rule...
If it ends 0000 it is STOCK
If it ends .hspl it is hspl
Yes, run hspl.exe again, choose 2.08.hspl
Click to expand...
Click to collapse
agree! absolutely right

Erm well after the white HTC screen I get the MAGLDR screen that boots to my NAND ROM. I pressed the power button while it was booting but nothing happened.

Skellyyy said:
It's still HSPL though? It's just the previous version that's .0000 instead of .HSPL or am I completely off? Do I need to flash HSPL.2.08.HSPL again or can i just keep it .0000?
Click to expand...
Click to collapse
You will still need 2.08.hspl if you want to reinstall or update your magldr version at some stage. It wont work on 2.08.0000.

Skellyyy said:
Erm well after the white HTC screen I get the MAGLDR screen that boots to my NAND ROM. I pressed the power button while it was booting but nothing happened.
Click to expand...
Click to collapse
Sounds to me like you arent rpessing quick enough. keep holding power from the moment you power on if it helps.
the instructions are to hold power (end key) right from turning on until magldr menu appears, but for me, i watch the first splash screen, and just before it ends (6-7 seconds) only then do i press and hold the end key. do not let go of the end key until teh menu appears, else it will continue to boto the rom.

Oh so all you wanted to know is if I can boot to MAGLDR menu? Yeah, I can lol.

Wait a minute, you can't have MAGLDR unless you have HSPL (HSPL3 2.08) if you have just reflashed HSPL, That means you still don't have MAGLDR, unless you have flashed it already in which case you still don't have a working ROM (Android or Windows 7) until such time you chose an Android or Windows 7 build. confusing?
Here is the sequence of flash events.
1. HSPL3 - 2.08HSPL
2. MAGLDR 1.13
3. Flash your chosen ROM.

HD2 wont allow me to flash anything, was running Android NAND

HELP my HD2 wont let me flash anything to it
What happened was, the phone froze so i turned back on and it just loads a white screen and thats it.
i can get to the boot loader, but nothing will flash to it and it wont boot/install the the stock rom from SD CARD. a bunch of red numbers come up then it goes back to the boot loader.
is it dead?

Remove the battery for 3 minutes and replace...then press power button (red) without letting go until you get in to MGLDR screen.

hi, thank for the advice...gave it ago and nothing, just a white screen

when you hold down and get into bootloader, you're saying you can't flash the stock ROM via RUU?
what happens?
are you 100% sure it's the right stock rom?
I would flash task29 via RUU, then try a ROM again (doesn't have to be stock if HSPL is on there)
on the "red numbers" does it give an SPL version?

i tried a task29 and it just sits on 0%
SPL version is 2.08 HSPL 8G XE
nothing will go to it, when trying to flash via usb it goes into recovery mode on the pc (the RUU program)
when via SD card it goes to loading...
then 00068002 in red pops up then it goes back to the loader (Serial) at the bottom
im stumped

run HSPL4 and uninstall HSPL, then try stock ROM again via official ROM,
you can also try flashing SPL 3.03 via HSPL4, then trying a winmo ROM.

same problem with my phone, but I got it fixed:
http://forum.xda-developers.com/showthread.php?t=994365
Hope it helps.
Andy

orangekid said:
run HSPL4 and uninstall HSPL, then try stock ROM again via official ROM,
you can also try flashing SPL 3.03 via HSPL4, then trying a winmo ROM.
Click to expand...
Click to collapse
hi.
it will allow me to change the HSPL but then im back to square one, think im gonna bin it tbh.

[Q] Can't get the Rom update utility to work

Hi,
I want to instal WP7 on my HTC HD2.
In the tutorial i use i should use the Rom update utility to get MAGLDR on my phone.
When i try to use this utility i don't get further than 0% and after some time i get a error (error 626)
What i did is:
- I reseted my HTC HD2.
- I started the Rom update utility. It says that i need a update from 1.66.404.1 to 2.00.000.0.
- So when i start this it will restart my phone and show me a progres bar.
This will stay on 0% and after 10 minutes the utility gives me a message that says:
You connection is lost(error 626). Than i need to "recover" my phone by taking the battery out and put in in again.
When i do this it wel restart my phone with the WM6.5 so nothing happend.
I tryed the following things:
- A different usb cable and usb port.
- redownload the Rom Update Utility from this site.
- Hard reset my phone.
Nothing happend a still geth the same error.
Does someone know how to fix this?
Or is there a defferent way to install WP7 on my HTC HD2.
Thanks,
Maarten

read tutorial from my signature

I will try that thanks.

I finished step 0.5 and 1.
But when I am at the line "When phone boot in MAGLDR use:"
I get stuck.
The MAGLDR is installed but when the phone restart i get stuck on the white HTC screen.
Any clou what i should do next?

if not boot, press and hold power button to start magldr....

I tryed it but it wont do anything else than go to the white boot sreen with the Green HTC logo.
I tryed to press the power button for a long time and while he is booting.
Butt notting more than te boot screen shows.
The only way to start the phone again is to remove the battery.
I can get in the "red-green-blue-white screen"
I already tryed to reinstall the magldr. But no luck.
And what do you meen with "in not boot"?
The only thing it does do is boot to this logo and that's it. So its always booting when i turn it on...

"if not boot to magldr"
which HSPL you have installed on device?
try install WM6.5 first then install magldr....
first time when phone boot after magldr flashed, must boot to magldr automatically

I have HSPL2.08
It doesn't start the magldr automatically.
Even if i hold the power button. It just starting with a white boot screen with HTC logo.
Don't know how to install wm6.5 again.
Please help. I would like to use my phone tomorow again.
Edit:
Maybe it's bricked...

boot to threecolor screen and flash WM6.5

Ok I flash back to WM6.5
What to do now?
Follow the instructions again i asume.
Anyway many thanks for your help!!!

yes, after flash, install magldr and continue...

Ok I flashed my phone back to WM6.5
This is working again.
After that I installed the magldr but it doesn't load anything after that.
It says the flash went correct but when the phone reboots it goes to the white htc boot logo. And thats it.
Even if i start the phone with the power button on it doesn't go to the magldr.
Did i install the right one?
I installed the MAGLDR113_DAF
After that i tryed to flash the rom to WP7.5 but is says that the phone is not connected.
Don't know what to do anymore.

you cant flash WP7 without magldr menu (setting options and enable USB flasher in magldr)...
yes this magldr is ok...
http://forum.xda-developers.com/showthread.php?t=893618
to be sure, which version of HD2 you have?
also check data in bootloader screen (threecolor)

Data in bootloader screen:
PB81100 HX-BC
SPL-2.08.HSPL 8G XE
0x05
CotullaHSPL 0x50
Version:
I know i don't have the t-mobile version.
HTC HD2 T8585

MasterMaarten said:
Ok I flashed my phone back to WM6.5
This is working again.
After that I installed the magldr but it doesn't load anything after that.
It says the flash went correct but when the phone reboots it goes to the white htc boot logo. And thats it.
Even if i start the phone with the power button on it doesn't go to the magldr.
Did i install the right one?
I installed the MAGLDR113_DAF
After that i tryed to flash the rom to WP7.5 but is says that the phone is not connected.
Don't know what to do anymore.
Click to expand...
Click to collapse
did you perform the magdlr prep steps of clearing the mbr and uselast24nand from the services option of the main menu, then select option 5 (main menu) usb flash...then flash rom?

hjhjhj said:
did you perform the magdlr prep steps of clearing the mbr and uselast24nand from the services option of the main menu, then select option 5 (main menu) usb flash...then flash rom?
Click to expand...
Click to collapse
I used the manual from dxdy:
STEP 0.5 - from same beginning, WP7 never or not installed on phone
- If needed (if Android NAND installed, or if any error during flash
process, erase NAND with Task29). Flashing WM6.5 not needed.
- if you have SIM locked phone and want unlock with code, you can this only in WM6.5
- insert formatted microSD card to FAT32 in phone
- flash radio if you want (if flash version available) or use radio upgrade during ROM flashing (put radio file
part00.bin in data.zip file before ROM flash)
STEP 1. - when HSPL and/or MAGLDR not installed
- Flash HSPL 2.08 if needed (put device in bootloader before Flash:
press and hold Volume down + Power button)
- Flash MAGLDR 1.13 (put device in bootloader before Flash:
press and hold Volume down + Power button)
Click to expand...
Click to collapse
- I didn't erease the NAND with Task29 because i don't have android installed.
But after the last step it wont go in to the MAGLDR.
- I didn't Flash the Radio. Is this needed?
Where can i find the radio version that is installed? Or does it need to be a tweakt version from this forum?

MasterMaarten said:
I used the manual from dxdy:
- I didn't erease the NAND with Task29 because i don't have android installed.
But after the last step it wont go in to the MAGLDR.
- I didn't Flash the Radio. Is this needed?
Where can i find the radio version that is installed? Or does it need to be a tweakt version from this forum?
Click to expand...
Click to collapse
you should do task29 whether you have android or not....between flashes even if wp7. task29 cleans out the memory area where the OS will reside.
as for the radio...radio thread for the TMOUS radio is here:
http://forum.xda-developers.com/showthread.php?t=1111613
more than likely you shouldn't have to flash a radio, but it won't hurt. only have to do it once.
in order to use the rom flash utility...you have to go into magdlr main screen...scroll down to and select 10. Services, then select 5. CleanMBR, and then 4. Uselast24NAND. Finally, back at the main set of options select 5. USB Flash.
Then you kick off your DWI.exe in admin mode.