Can someone please help. I went to the sticky thread to get all info to install android
http://forum.xda-developers.com/showthread.php?t=893948
My system information is:
ROM Version 3.14.531.1
Radio Version 2.15.50.14
I started with loading HSPL on my phone being my radio is 2.15.50.14 which is a requirement for HSPL4. When I install HSPL I connect my phone via sync and the computer detects it and runs through the install. It even shows the "We Hacked It" screen on my phone as its supposed to but when I hold volume down and the power button my phone doesn't show HSPL 2.08, I only see SPL-2.10.0000 8G XE
When I tried to continue loading Magldr from there I get an error and I can't go any farther. Can someone please help, how do I get HSPL to actually load which will allow me to load Magldr.
Thanks
O
What error do you get?
Try manually going into bootloader by holding down the Volume Down button and then powering on phone (still holding volume down).
Then plug in USB and load up MAGLDR DFT flasher.
Thanks TheATHEiST
However I can't get to the bootloader page. I corrected my previous post when I hold the volume button and power button down I get the four color screen that only shows the SPL version I have. I don't know why the HSPL flash doesn't work.
Related
Hello,
its been quite a long time I installed HSPL. Now im about to install mglrd, but im quite unsure which HSPL. Booting with Volume Down it says SPL-1.66.HSPL XE - does that mean that both the SPL and HSPL version are 1.66 or just SPL?
Thanks in advance!
You can see the HSPL version when you hold the volume down button directly after turning on (or soft-resetting) te device. You will get in the tri-color screen which shows some info like (H)SPL version.
Soft reset or pull battery for a normal boot.
oh i got a serious problem
after I install MAGLDR 1.11 my HD2 it succeed and did reboot and then it did stuck in white screen with hTC green log.
What to do? It cannot connect it to the sync with computer when it is with this screen. I tried so many time to reset it (with pressing long the power bottom) but I didn’t get MAGLDR 1.11 boot menu, so I cannot proceed to the next step which is installing NAND
My HTD looks like with no operating system only with white screen with hTC green log, What to do? Any help PlZzZzZzZzZzzzz?
Milan Geek said:
oh i got a serious problem
after I install MAGLDR 1.11 my HD2 it succeed and did reboot and then it did stuck in white screen with hTC green log.
What to do? It cannot connect it to the sync with computer when it is with this screen. I tried so many time to reset it (with pressing long the power bottom) but I didn’t get MAGLDR 1.11 boot menu, so I cannot proceed to the next step which is installing NAND
My HTD looks like with no operating system only with white screen with hTC green log, What to do? Any help PlZzZzZzZzZzzzz?
Click to expand...
Click to collapse
Do you have 2.08HSPL on your phone?
Hold the volume key down while you turn on your phone, then you will see the tri-color screen. and the hardspl you have.
I suggest you follow this
Make your you have flashed HSPL 2.08.
it can be found easily using search option
after that boot it to tri-color screen.
( hold volume down key and boot your phone)
Sync your phone with pc using active sync
then down there on your phone screen will say USB
now find
"Task29 provided by doloop"
in the forum.
use that to flash everything from your phone.
after that it will automatically boot into white htc logo screen and not proceed
(due to there's nothing remaining.) just ignore it and
reset your phone while pressing volume down key to enter tri-color screen
now flash mgldr.
after that your phone will boot into mgldr
then follow the instructions on forum about nand builds
PS/If you are using XP you have to make your when usb flasher
it says wait usb...usb(connect via active sync) then uncheck "the allow usb connection" on active syncs connection settings. then proceed will rom installers
hope this will help.
dirn1111 said:
Make your you have flashed HSPL 2.08.
it can be found easily using search option
after that boot it to tri-color screen.
( hold volume down key and boot your phone)
Sync your phone with pc using active sync
then down there on your phone screen will say USB
now find
"Task29 provided by doloop"
in the forum.
use that to flash everything from your phone.
after that it will automatically boot into white htc logo screen and not proceed
(due to there's nothing remaining.) just ignore it and
reset your phone while pressing volume down key to enter tri-color screen
now flash mgldr.
after that your phone will boot into mgldr
then follow the instructions on forum about nand builds
PS/If you are using XP you have to make your when usb flasher
it says wait usb...usb(connect via active sync) then uncheck "the allow usb connection" on active syncs connection settings. then proceed will rom installers
hope this will help.
Click to expand...
Click to collapse
thank you dear, i will try it today when i get home and i wish it will work
a3r0n1 said:
Do you have 2.08HSPL on your phone?
Hold the volume key down while you turn on your phone, then you will see the tri-color screen. and the hardspl you have.
Click to expand...
Click to collapse
i have 1.42 !!
i cannot sync with the PC, how to flash 2.08 now?
Make sure you have the right hspl and radio.
Sent from my HTC HD2 using XDA App
dirn1111 said:
Make your you have flashed HSPL 2.08.
it can be found easily using search option
after that boot it to tri-color screen.
( hold volume down key and boot your phone)
Sync your phone with pc using active sync
then down there on your phone screen will say USB
now find
"Task29 provided by doloop"
in the forum.
use that to flash everything from your phone.
after that it will automatically boot into white htc logo screen and not proceed
(due to there's nothing remaining.) just ignore it and
reset your phone while pressing volume down key to enter tri-color screen
now flash mgldr.
after that your phone will boot into mgldr
then follow the instructions on forum about nand builds
PS/If you are using XP you have to make your when usb flasher
it says wait usb...usb(connect via active sync) then uncheck "the allow usb connection" on active syncs connection settings. then proceed will rom installers
hope this will help.
Click to expand...
Click to collapse
the problem that i have hspl 1.42
now i cannot sync with the PC, how can i flash hspl 2.08?
Boy, you never read, do you!
go there:
http://forum.xda-developers.com/showthread.php?t=915839
Don't panic, take it easy...
MAGLDR requirements:
HSPL 2.08
RADIO that supports 576MB RAM
Milan Geek, I know I am going blind, but seriously?
YOU DON'T NEED SUCH BIG FONTS
This is what you need to do:
Unplug battery to turn device off
Put battery back in to device
Hold the Volume down button, do not let go
Press and release the power button to turn on the device
when you see the RED/GREEN/BLUE screen, plug in your USB cable to phone and computer
Run HSPL3 and update to HSPL 2.08
When done, the phone will Reboot, when screen turns off, press and hold the Volume Down button, if you don't, you will have to remove battery, put it back, hold the volume button, then turn on the device again.
when you see the RED/GREEN/BLUE screen again, make sure USB cable is connected to phone and computer install RADIO 2.15.50.14
Now MAGLDR will work.
If these instructions do not work,
MAIL IT TO ME, AND I WILL CLICK ON THANK YOU BUTTON
The phone is too complicated, I will find it a nice home.
Doesn't Work
nimbooz said:
Doesn't Work
Click to expand...
Click to collapse
What doesn't work? If OP just takes his time to read and understand all wat d above posters have posted, then he'll surely successfully get android on his device...The steps above have been used by thousands over and over again WITHOUT fail!!!...
Same problem. I have reinstalled around 20 times following steps you say and still stucks in white screen.
sanroman said:
Same problem. I have reinstalled around 20 times following steps you say and still stucks in white screen.
Click to expand...
Click to collapse
It's a simple process. If you are getting stuck at white screen the chances are you are not doing one of the first 2 steps as below.
FIRST: You have to install 2.08.HSPL (no other HSPL version and not an spl ending in .0000). Check in bootloader that you have 2.08.hspl NOT 2.08.0000.
SECOND: You have to install a 2.xx.50.xx radio (it has to be a .50 radio and not a .51 radio). Use 2.08.50.xx or higher .50 radio.
THIRD: Install magldr from bootloader by running the romupdateutility file.
I know. Please Believe I have 2.08.HSPL and 2.15.50.15 Radio installed several times without errors but same result.
Could be a HW problem? any other solution?
sanroman said:
I know. Please Believe I have 2.08.HSPL and 2.15.50.15 Radio installed several times without errors but same result.
Could be a HW problem? any other solution?
Click to expand...
Click to collapse
Have you tried going all the way back to stock winmo rom and starting the whole process again?
I know. Please Believe I have 2.08.HSPL and 2.15.50.15 Radio installed several times without errors but same result.
Could be a HW problem? any other solution?
sanroman said:
I know. Please Believe I have 2.08.HSPL and 2.15.50.15 Radio installed several times without errors but same result.
Could be a HW problem? any other solution?
Click to expand...
Click to collapse
You posted this above in your previous post already. I was now asking if you have tried going all the way back to the stock winmo rom, ie to return the phone to its original state and then start again from the beginning?
nimbooz said:
Doesn't Work
Click to expand...
Click to collapse
I had the same problem and it worked.....just follow the steps the guys described below and u will succes :-D
LiFE1688 said:
MAGLDR requirements:
HSPL 2.08
RADIO that supports 576MB RAM
Milan Geek, I know I am going blind, but seriously?
YOU DON'T NEED SUCH BIG FONTS
This is what you need to do:
Unplug battery to turn device off
Put battery back in to device
Hold the Volume down button, do not let go
Press and release the power button to turn on the device
when you see the RED/GREEN/BLUE screen, plug in your USB cable to phone and computer
Run HSPL3 and update to HSPL 2.08
When done, the phone will Reboot, when screen turns off, press and hold the Volume Down button, if you don't, you will have to remove battery, put it back, hold the volume button, then turn on the device again.
when you see the RED/GREEN/BLUE screen again, make sure USB cable is connected to phone and computer install RADIO 2.15.50.14
Now MAGLDR will work.
If these instructions do not work,
MAIL IT TO ME, AND I WILL CLICK ON THANK YOU BUTTON
The phone is too complicated, I will find it a nice home.
Click to expand...
Click to collapse
Had similar problem with MAGLDR, had no idea what to do. Found this forum and these instructions. Took some fiddling but finally got it working. THANX SO MUCH!!!
same problem doesnt work
Hi all
Newbie. And new to Phone Updates etc.....
Have HTC HD2 on O2. Was attempting to put NAND on it, followed the thread:
http://forum.xda-developers.com/showpost.php?p=11215136&postcount=8
All steps conpleted successfully, but after "Step C: Install MAGLDR"
The MAGLDR113 Rom updated the phone successfully, then it rebooted and is now stuck the O2 screen.
Any help would be appreciated.
what rom did you flash after you installed magldr?
try to flash magldr again
u got hspl 2.08 ?
Do you have the correct radio (2.15.50.14) ?
have you tried pressing the power button on booting?
Flash again winmo 6,5. After that flash HSPl 3.0. Flash radio 2.15.50. In boot screen ( hold power button and volume down) Flasyh Magldr.
I would say invisiblebm is right - reflashing again should help - cause as long as your reacts when you push the power button it is not dead
Hi all. Thanks for info.
Current state is that the phone is frozen at 02 welcome screen. Nothing happens when soft or hard boot.
When you boot holding down arrow I get
PB8110 SS-BC
SPL-3.03.hspl XE
0x05
cotullaHSPL 0x50
Unable to reflash, as the phone doesnt showup to the pc on usb, though the white part of the 4 colours RED/GREEN/BLUE/WHITE does change from serial to USB when you connect to the PC.
Phone shows up as a device "qualcomm cdma technologies MSM"
Is there anything more I can do save for sending back to O2.
Was at version o SPL 1.66.0000
I choose 3.03HSPL
Leo 2.15.50.14.rar contents - Via CustomRUU
The MAGLDR113 113 from the XDA Dev Site
Completed successfully, then rebooted, but didnt come up.
cheers
John
Even thought there is no apparent phone connection, it still connects if it switches from serial to USB. I had the same problem. Mine also said qualcomm techs. But when i reflashed MAGLDR using DAF.exe, it worked fine.
Can you post the link to the downlaod please
Just put the phone in bootloader, connect USB, when says "USB" on bottom of phone screen, its ready for flashing. Ignore the fact the PC doesn't seem to connect, the phrase "get an activesync connection" in the various tutorials is a pain in the arse, (even though it is technically correct.)
Anyway, magldr won't start cos you have the wrong hspl. As you already know because it says so in post 1 of the magldr thread, which you DID read, right? It says magldr will only work with 2.08.hspl, , , you have 3.03.hspl.
Enter bootloader, connect USB, run hspl4, choose 2.08.hspl and reboot, magldr should start.
So what I understud is , that the phone is not connecting to the PC. Try this:
Restart you PC, Go in to bootloader and try again, In most of the cases is some conection error between the devices. It hapen to me many times.
Thanks. Missed the SPL-3.03, rushing to do it. Its now on 2.08 and the loader comes up. Just the flash to do next. cheers
lesson of the day?
Always read the instructions 10 times
very very very true
Thanks to all fro your help btw, since running Nand, and now Gingerbread 2.3.
samsamuel said:
Just put the phone in bootloader, connect USB, when says "USB" on bottom of phone screen, its ready for flashing. Ignore the fact the PC doesn't seem to connect, the phrase "get an activesync connection" in the various tutorials is a pain in the arse, (even though it is technically correct.)
Anyway, magldr won't start cos you have the wrong hspl. As you already know because it says so in post 1 of the magldr thread, which you DID read, right? It says magldr will only work with 2.08.hspl, , , you have 3.03.hspl.
Enter bootloader, connect USB, run hspl4, choose 2.08.hspl and reboot, magldr should start.
Click to expand...
Click to collapse
CHEERS, you were a life saver.
First things first.....first post!
Ok so I have the HD2 512 version and have put hspl 2.08 on it with no problems but when I have tried loading magldr1.13 the install seems to go ok on the phone but when it reboots magldr doesnt launch it simply stays on the default white htc launch screen.
My own fault for following a youtube video I guess.
The handset lets me reflash magldr which I did a couple of times and I tried an older version of magldr and also used the nand toolkit to try and install magldr but still the same white screen on launch.
Any ideas whats going on anyone? help appreciated with thanks
PeteLeMeat said:
First things first.....first post!
Ok so I have the HD2 512 version and have put hspl 2.08 on it with no problems but when I have tried loading magldr1.13 the install seems to go ok on the phone but when it reboots magldr doesnt launch it simply stays on the default white htc launch screen.
My own fault for following a youtube video I guess.
The handset lets me reflash magldr which I did a couple of times and I tried an older version of magldr and also used the nand toolkit to try and install magldr but still the same white screen on launch.
Any ideas whats going on anyone? help appreciated with thanks
Click to expand...
Click to collapse
Are you sure you installed HSPL correct? Hold down the volume button and press the power button, till the rainbow screen, does it say something about cotulla hspl? If yes, connect the phone to the computer(still in the rainbow screen of course) and wipe the device(task29). After that your device will be totally clean and the correct radio is installed. So you will have to press the volume down button again to enter the rainbow screen and then install magldr.
Yes it does say cotulla.
So I tried what you said I connected in rainbow screen and pressed wipe(task 29) in the nand toolkit (wipe from the toolkit right?) but in the rainbow screen it says cotulla still,
tried magldr again, same white screen
when you saying "launching Mgldr", are you pressing the power button(end key) when the phone boots? this way only you enter Mgldr and loads the menu
Yes I have tried holding the power button on powering on the device and tried it without holding, still the same white htc screen and no movement from there.
When I wipe the handset it still has SPL-2.08.HSPL on it and still says CollutaHSPL.
I'm guessing I should try and restart from scratch??
you havent flashed a compatible radio yet, , magldr wont start without it.
enter bootloader
usb
flash radio 2.15.50
reboot
magldr.
Ok I will try that now. Is radio 2.15.50.14 ok?
Wahey! I'm in!
Thanks very much you guys are legends!
Right next step haha. Don't worry I'll read up on it don't want to hassle anyone.
Any suggestions what are the best roms for WP7 or ICS??
(and if you have time point me in the right direction of them)
Any other step I am missing?
Again thanks for your help
Different people, different needs
Check some threads (also Search, will not hurt you )
http://forum.xda-developers.com/showthread.php?t=1656171
http://forum.xda-developers.com/showthread.php?t=1430276
http://forum.xda-developers.com/showthread.php?t=955268
http://forum.xda-developers.com/showthread.php?t=1678153
http://forum.xda-developers.com/showthread.php?t=1670456
Flashing guides - in my signature
I began with a stock HTC HD2 (non-US) and followed this guide to install MAGLDR 1.13.
The unlocked rgb bootloader with power+vol dwn says the following:
PB81*** SS-BCSPL-2.08.HSPL 8G XE0x05CotullaHSPL 0x50
...so I assume that HSPL 2.08 flashed properly. The radio update to 2.15.50.14 also appeared to flash properly as did MAGLDR 1.13. I did all of this from a Windows XP workstation logged in as Administrator.
When I boot the phone I get a bright white screen with HTC in green, and nothing else, indefinitely. If I hold the power button to boot I get the same so no MAGLDR bootloader access. The only thing I can access is the unlocked rgb bootloader. Any help would be gratefully appreciated as I am reaching the point of launching the phone into the lake. Even some kind words would be soothing at this point. All the best.