Database Users

[Q] Hd2 bricked

I've tried to downgrade my HD2 from 3.14 to 1.66 from SD with leoimg.nbh
But I was wrong and I pressed powerButton instead of pressing volDown.
The result is:
00028002
Not allow
Then because the SPL is changed to 1.42, I've try to reflash 3.14, but the situation now is:
Now in bootloader I have
RUUNBH
PB81100 HX-BC
SPL-3.03.0000 XE
MicroP(LED) 0x05
MicroP(TOUCH) 0x50
Upgrade ROM code error
Please try again
Someone can help me please?
thanks a lot!!
Now if I flash an original ROM I recieved VENDOR ID NOT ALLOWED
Sorry for my poor english...

So you haven't got hspl?
Try holding down both volume up and down and power button that'll do a hard reset
Sent from my HTC HD2 using Tapatalk

Restart the SD Card flashing again with the 1.66 ROM.

Eyy i got some other problem,
when i flashed to SPL-2.08.0000 8G XE
the stock rom didnt start after i flashed it,
i had white screen, then i tried to install radio 2.15.50.14 it gets stuck at 96% and i get ''96%!!'' and now nothings works...
some one any advice? or shall i start a new topic?
Thnx

luca_v3r said:
....
Now if I flash an original ROM I recieved VENDOR ID NOT ALLOWED
Sorry for my poor english...
Click to expand...
Click to collapse
Download the ROM from HTC's website, using your phone's serial number. It may be a stock ROM or one with the telephone company's name on it. You will not be allowed to download one which is not allowed on your phone.

So you haven't got hspl?
Try holding down both volume up and down and power button that'll do a hard reset
Click to expand...
Click to collapse
Now I don't have hspl , hard reset when i press VolUp for restore nothing happened ..
Restart the SD Card flashing again with the 1.66 ROM.
Click to expand...
Click to collapse
The response is not allowed..

pokerfreakje said:
Eyy i got some other problem,
when i flashed to SPL-2.08.0000 8G XE
the stock rom didnt start after i flashed it,
i had white screen, then i tried to install radio 2.15.50.14 it gets stuck at 96% and i get ''96%!!'' and now nothings works...
some one any advice? or shall i start a new topic?
Thnx
Click to expand...
Click to collapse
Download the ROM from HTC's website, using your phone's serial number. It may be a stock ROM or one with the telephone company's name on it. You will not be allowed to download one which is not allowed on your phone.
With the phone off, press and hold the Volume Down button then tap the Power button. You should now be in BootLoader mode.
Connect to your PC and the 'Serial' on the phone should change to 'USB'.
Now you can run the downloaded ROM. Please be patient, sometimes it can sit at 0% or 99% for a good five minutes.

Can i flash it to a android NAND, without a WM Rom? and with a radio 2.05?

You need at least 2.08 Radio. Also, you need HSPL and a Winmo rom to start the MAGLDR install.

Thanks thanks thanks thanks thanks thanks thanks
a lot of ALL!!!!!!
My error is that I try to flash a original ITALIAN rom, but my HD2 is from DE......
I'm very stupid...
Thanks ALL

You need to replace spl with hspl before flashing custom roms
Sent from my HTC HD2 using Tapatalk

please help

hi all I am trying to put android on my hd2 (uk version) but I am stuck i have pn the red green blue screen got
PB81100 HX-BC
SPL-3.03.HSPL XE
0x05
CotullaHSPL 0x30
i have read i need to flash a new radio rom? i have downloaded a custom ruu but when i click on it nopthing happens have i done something wrong. please help I have never done anytrhing like this before.
Thanks
mmmyoda

i think it may be the radio rom but i have downloaded the leo zip with it in is there anyway to install it?

download HSPL4 and install SPL 2.08
download 2.15.00 radio and flash that via RUU
Flash magldr 1.13 then clockwordmod recovery
flash your preferred ROM.

He means flash radio 2.15.50 but otherwise what he said above. Hspl and radio are key, it won't work with the 3.03.Hspl that you have,gotta be 2.08.Hspl

thanks guys I have managed to get it to spl-2.08 but when i try the ruu nothing happens i have the phone connected and double click the ruu it has a waiting curser and nothing more happens any ideas why?

mmmyoda said:
thanks guys I have managed to get it to spl-2.08 but when i try the ruu nothing happens i have the phone connected and double click the ruu it has a waiting curser and nothing more happens any ideas why?
Click to expand...
Click to collapse
Do you have 2.08.HSPL? If so then just right click on the RUU and Run as Administrator.
Sent from my HTC Vision using XDA App

yeah it says spl-2.08.hspl 8G XE
I have tried right clicking and running as admin a small blue circle appears and goes and then nothing else i have been trying to figure out why it goes no further any ideas? cheers

may be you have lower version of radio...use the 2.15 radio version....

cheers guys think its all running fine now, does a G with an up and down arrow mean i am on 3g? i have the desire nand running

mmmyoda said:
cheers guys think its all running fine now, does a G with an up and down arrow mean i am on 3g? i have the desire nand running
Click to expand...
Click to collapse
no that's gsm, the lowest of speed, you have E for edge/2g and 3g/H for 3g and hsdpa which is the fastest.

install SPL 2.08

[Q] How to install Magldr1.13 into my HTC HD2?

Dear all, how can install magldr1.13?
My HTC HD2 showed me "PB81100 SS-BC" in bootloader mode.
I could not to install magldr. Please help me this problem!
(i have HSPL 2.08 installed... )

Can you not read a simple guide? Make sure you have 2.08.HSPL and not .0000
Sent from my HTC Vision using XDA App

Skellyyy said:
Can you not read a simple guide? Make sure you have 2.08.HSPL and not .0000
Sent from my HTC Vision using XDA App
Click to expand...
Click to collapse
yes i had 2.08.hspl, but hold in white background and green htc logo when i installed the magldr1.13 and reboot it!

Hi henrywgs .. i have the same problem what you have faced .. i get stuck at the htc logo after installing magldr .. Information of the bootloader menu of my phone is
PB81100 ss-bc
SPL-2.08.HSPL 8G XD
0x02
CotullaHSPL 0x50
can u help me ?

barun rawat said:
. i get stuck at the htc logo after installing magldr ..
Click to expand...
Click to collapse
Yes of course you do. Installing magldr deletes winmo so there is no OS to boot, and the magldr menu wont appear unless spl is 2.08.hspl (ok so far) AND the radio is android compatible. (I suspect this is your problem).
Enter bootloader, flash radio 2.15.50, magldr should now start and you can move on to flashing cwm and the rom.

samsamuel said:
Yes of course you do. Installing magldr deletes winmo so there is no OS to boot, and the magldr menu wont appear unless spl is 2.08.hspl (ok so far) AND the radio is android compatible. (I suspect this is your problem).
Enter bootloader, flash radio 2.15.50, magldr should now start and you can move on to flashing cwm and the rom.
Click to expand...
Click to collapse
Hi .. i already have radio 2.15.50.14 .. 2.08hspl .. and i tried holding down the power key for almost 10 mins after installing MAGLDR 1.13
Here is everything about my phone ( i hope you can figure out some advice based on this)
Model number below the battery -: PB81110
( By the way on the body of my phone its written HTC PRO.THREE ) this is hd2 right?
Bootloader screen after i installed hspl -:
PB81100 SS-BC
SPL-2.08.HSPL 8G XD
0x02
CotullaHSPL 0x50
( this i dont understand because under the battery of my phone its written PB81110 and not PB81100)
Does this information help to figure out the problem with my phone?
I really appreciate your help

Pro 3 is a pre release test model with only 300some Meg ram. Not sure it will ever work. Can't help, sorry.

[Q] Please Help Flashing Issue

Hi,
Before I go into detail I've tried googling my issue for days now
I attempted to put HyperDroid on to my HD2 it had Windows Mobile 6.5 on it.
Following the instructions carefully firstly I updated from SPL-1.42.0000 to SPL-2.08.HSPL I did not have a problem doing this.
After that I installed MAGLDR v1.13 it loaded correctly (got to 100%) BUT when it rebooted my HD2 stays on the splash screen so matter what I can get it to boot into MAGLDR
Things I've Tried
Re-flashing MAGLDR v1.13
Tried MAGLDR v1.10 and v1.11
Flashing SPL-1.42.HSPL then installing MAGLDR
Flashing Task29 - Wiping then Re-flashing
Extensive Googleing
Installing cLK - Same Issue
PB81100 HX-BC
SPL-2.08.HSP 8G XE
[EMPTY SPACE] 0x05
CotullaHSPL 0x40
Am I missing something on the third line??
Any help would be greatly appreciated

do task29 > install radio > mag > usbflasher > recovery daf.exe...
then u can flash any rom u want

Thank You!
I'll try it tommrow

remember to use the right partition size based on rom u select.

SudoBen said:
Hi,
Before I go into detail I've tried googling my issue for days now
I attempted to put HyperDroid on to my HD2 it had Windows Mobile 6.5 on it.
Following the instructions carefully firstly I updated from SPL-1.42.0000 to SPL-2.08.HSPL I did not have a problem doing this.
Click to expand...
Click to collapse
so far so good
After that I installed MAGLDR v1.13 it loaded correctly (got to 100%) BUT when it rebooted my HD2 stays on the splash screen so matter what I can get it to boot into MAGLDR
Click to expand...
Click to collapse
because teh radio isnt right
Things I've Tried
Re-flashing MAGLDR v1.13
Tried MAGLDR v1.10 and v1.11
Flashing SPL-1.42.HSPL then installing MAGLDR
Click to expand...
Click to collapse
magldr will ONLY work on 2.08.hspl( it will FLASH, but not start)
Flashing Task29 - Wiping then Re-flashing
Extensive Googleing
Click to expand...
Click to collapse
reading post 1 of themagldr thread would have been more use, especially the bit where it says you MUST have a compatible radio.
Installing cLK - Same Issue
PB81100 HX-BC
SPL-2.08.HSP 8G XE
[EMPTY SPACE] 0x05
CotullaHSPL 0x40
Am I missing something on the third line??
Any help would be greatly appreciated
Click to expand...
Click to collapse
into bootloader, confirm spl line says 2.08.hspl, flash radio 2.15.50, restart, , voila, magldr.

samsamuel said:
so far so goodbecause teh radio isnt rightmagldr will ONLY work on 2.08.hspl( it will FLASH, but not start)reading post 1 of themagldr thread would have been more use, especially the bit where it says you MUST have a compatible radio.
into bootloader, confirm spl line says 2.08.hspl, flash radio 2.15.50, restart, , voila, magldr.
Click to expand...
Click to collapse
Thank you so much haha!!
I thought I bricked my phone from a while there

need help with nand flash

i just bought this phone and i have went to a couple of these guides and i cant figure out why none of the hard spl programs are working for me i have fallow the steps and it shows up in wmdc but yet when i run the ruu utility it has a connection error ? i was told it was on android once before but idk if that is true. this is what the bootloader says
pb81120 ss-b3
spl-2.08.hspl 8g xe
0x85
cotullahspl 0x50
if any of this helps as well here it is
os version
5.2.21913
manila version
2.5.20181425.0
Rom version
3.14.531.1 (04666) wwe
radio version
2.15.50.14

Andrew.80 said:
i just bought this phone and i have went to a couple of these guides and i cant figure out why none of the hard spl programs are working for me i have fallow the steps and it shows up in wmdc but yet when i run the ruu utility it has a connection error ? i was told it was on android once before but idk if that is true. this is what the bootloader says
pb81120 ss-b3
spl-2.08.hspl 8g xe
0x85
cotullahspl 0x50
if any of this helps as well here it is
os version
5.2.21913
manila version
2.5.20181425.0
Rom version
3.14.531.1 (04666) wwe
radio version
2.15.50.14
Click to expand...
Click to collapse
Your bootloader is showing that hspl is installed.

Your HardSpl is ok.
Your Radio is also ok.
After this you try to install Magldr or CLK?
If so, what is the error?

Taco123 said:
Your HardSpl is ok.
Your Radio is also ok.
After this you try to install Magldr or CLK?
If so, what is the error?
Click to expand...
Click to collapse
it is showing that there is a connection error in magldr

What's your problem? HSPL is installed, so just go ahead and install either cLK or MAGLDR, CWM and then a ROM
EDIT: Sorry, literally seconds after your post above

does the magldr version matter the guide i was using was 13 but i keep getting connection error when it gets to the point when it puts my phone in the bootloader screen

Andrew.80 said:
does the magldr version matter the guide i was using was 13 but i keep getting connection error when it gets to the point when it puts my phone in the bootloader screen
Click to expand...
Click to collapse
Well MAGLDR 1.13 is the only one that works properly nowadays as pretty much all ROMs are flashed through CWM and (I think) only MAGLDR 1.13 supports this, plus WP7 support. Also can you connect in bootloader screen (rather than MAGLDR boot into bootloader then try to connect USB)?

Nigeldg said:
Well MAGLDR 1.13 is the only one that works properly nowadays as pretty much all ROMs are flashed through CWM and (I think) only MAGLDR 1.13 supports this, plus WP7 support. Also can you connect in bootloader screen (rather than MAGLDR boot into bootloader then try to connect USB)?
Click to expand...
Click to collapse
tried that got error 260 connection

could it be a driver problem?