Database Users

HTC HD2 Hung at opening.

My phone is stuck at the opening white screen. HTC writing wont come up and it wont open. i can go into the bootloader. i guess i did something wrong while flashing a rom. can u help me please.
PB81100 HX-BC
SPL-2.08.HSPL 8G XE
0x05
CotullaHSPL 0x30
this writes in the boot screen.

did you just flash a cooked rom and haven't yet changed the radio?

probably. ive no idea what to do know to be honest ive given it to repair they said the main board needs to be changed but i dont think its a hardware problem. could u tell me what to do. step by step. i flashed a rom thats true but i havent flashed a radio before doing it.

calen8 said:
My phone is stuck at the opening white screen. HTC writing wont come up and it wont open. i can go into the bootloader. i guess i did something wrong while flashing a rom. can u help me please.
PB81100 HX-BC
SPL-2.08.HSPL 8G XE
0x05
CotullaHSPL 0x30
this writes in the boot screen.
Click to expand...
Click to collapse
I think you forgot to flash Radio ROM - look into thread of the ROM you flashed, there must be info about radios which are "approved"

thing is i dont know which rom is flashed right now and ive no idea about the radio also.

calen8 said:
thing is i dont know which rom is flashed right now and ive no idea about the radio also.
Click to expand...
Click to collapse
First of all - if you want to do something - read first and gather some info, otherwise you'll have problems.
And if the problem really is with radio, then try THIS first, it should help

just flash a high version radio, which should work regardless of what rom is there.
2.12.50.x or 2.10.50, one of them.

I am flashing the radio from sd and it says
00018003
LEOIMG.nhb - FAIL
Radio - Fail
Update Terminate
Update fail

i am no expert but perhaps try following this method picking a rom you like and also an exceptable radio. good luck
http://forum.xda-developers.com/showpost.php?p=6933055&postcount=14111

try flashing a different rom and see what happens

calen8 said:
ive given it to repair they said the main board needs to be changed
Click to expand...
Click to collapse
oh right its been back to service and got refused,
run hspl2,
choose a stock spl (so 1.66.0000 for a normal hd2 or hspl3 and choose 2.08.0000 for a tmous phone,) and send it back again.

hspl wont change the version =(

oh, well all i can suggest then is you try hspl2, ever option, and hspl3, every option, , maybe one of them can trigger the spl to change.

wont work =(

[Q] Hd2 bricked

I've tried to downgrade my HD2 from 3.14 to 1.66 from SD with leoimg.nbh
But I was wrong and I pressed powerButton instead of pressing volDown.
The result is:
00028002
Not allow
Then because the SPL is changed to 1.42, I've try to reflash 3.14, but the situation now is:
Now in bootloader I have
RUUNBH
PB81100 HX-BC
SPL-3.03.0000 XE
MicroP(LED) 0x05
MicroP(TOUCH) 0x50
Upgrade ROM code error
Please try again
Someone can help me please?
thanks a lot!!
Now if I flash an original ROM I recieved VENDOR ID NOT ALLOWED
Sorry for my poor english...

So you haven't got hspl?
Try holding down both volume up and down and power button that'll do a hard reset
Sent from my HTC HD2 using Tapatalk

Restart the SD Card flashing again with the 1.66 ROM.

Eyy i got some other problem,
when i flashed to SPL-2.08.0000 8G XE
the stock rom didnt start after i flashed it,
i had white screen, then i tried to install radio 2.15.50.14 it gets stuck at 96% and i get ''96%!!'' and now nothings works...
some one any advice? or shall i start a new topic?
Thnx

luca_v3r said:
....
Now if I flash an original ROM I recieved VENDOR ID NOT ALLOWED
Sorry for my poor english...
Click to expand...
Click to collapse
Download the ROM from HTC's website, using your phone's serial number. It may be a stock ROM or one with the telephone company's name on it. You will not be allowed to download one which is not allowed on your phone.

So you haven't got hspl?
Try holding down both volume up and down and power button that'll do a hard reset
Click to expand...
Click to collapse
Now I don't have hspl , hard reset when i press VolUp for restore nothing happened ..
Restart the SD Card flashing again with the 1.66 ROM.
Click to expand...
Click to collapse
The response is not allowed..

pokerfreakje said:
Eyy i got some other problem,
when i flashed to SPL-2.08.0000 8G XE
the stock rom didnt start after i flashed it,
i had white screen, then i tried to install radio 2.15.50.14 it gets stuck at 96% and i get ''96%!!'' and now nothings works...
some one any advice? or shall i start a new topic?
Thnx
Click to expand...
Click to collapse
Download the ROM from HTC's website, using your phone's serial number. It may be a stock ROM or one with the telephone company's name on it. You will not be allowed to download one which is not allowed on your phone.
With the phone off, press and hold the Volume Down button then tap the Power button. You should now be in BootLoader mode.
Connect to your PC and the 'Serial' on the phone should change to 'USB'.
Now you can run the downloaded ROM. Please be patient, sometimes it can sit at 0% or 99% for a good five minutes.

Can i flash it to a android NAND, without a WM Rom? and with a radio 2.05?

You need at least 2.08 Radio. Also, you need HSPL and a Winmo rom to start the MAGLDR install.

Thanks thanks thanks thanks thanks thanks thanks
a lot of ALL!!!!!!
My error is that I try to flash a original ITALIAN rom, but my HD2 is from DE......
I'm very stupid...
Thanks ALL

You need to replace spl with hspl before flashing custom roms
Sent from my HTC HD2 using Tapatalk

[Q] stuck on boot screen after flashing MAGLDR

I flashed MAGLDR from DFT_LEO70_RELEASE and now i'm stuck on bootscreen and can't get into MAGLDR
tried task29 then MAGLDR again but still the same prob.
any help?
thanx in advance

ahmedsalem89 said:
I flashed MAGLDR from DFT_LEO70_RELEASE and now i'm stuck on bootscreen and can't get into MAGLDR
tried task29 then MAGLDR again but still the same prob.
any help?
thanx in advance
Click to expand...
Click to collapse
turn off your phone, press and hold power button while you turn on your phone until you see the MAGLDR menu.

waichai said:
turn off your phone, press and hold power button while you turn on your phone until you see the MAGLDR menu.
Click to expand...
Click to collapse
Tried this but nothing happens
it remains stuck on bootscreen

ahmedsalem89 said:
Tried this but nothing happens
it remains stuck on bootscreen
Click to expand...
Click to collapse
do you have 2.08HSPL on your phone?

I'm pretty Sure i have hard spl
but i'm not sure what version

ahmedsalem89 said:
I'm pretty Sure i have hard spl
but i'm not sure what version
Click to expand...
Click to collapse
hold the volume key down while turn on your phone, then you will see the tri-color screen. you will know what hardspl you have.

it written
spl-1.42.hspl xe
0x05
CotullaHSPL 0x50

ahmedsalem89 said:
it written
spl-1.42.hspl xe
0x05
CotullaHSPL 0x50
Click to expand...
Click to collapse
you have hardspl on your device, but it's not 2.08hspl. you need to update to 2.08hspl. Otherwise MAGLDR won't work with your current 1.42hspl.

Downloaded Hspl3 and flashing now but there r 2 options
2.08.0000
and
2.08.hspl
should i choose the second one

ahmedsalem89 said:
Downloaded Hspl3 and flashing now but there r 2 options
2.08.0000
and
2.08.hspl
should i choose the second one
Click to expand...
Click to collapse
2.08hspl, NOT 2.08.0000

Alright flashed hardspl and it booted directly into MAGLDR
now i'll continue installing WinPho 7
I really can't Thank u enough

ahmedsalem89 said:
Alright flashed hardspl and it booted directly into MAGLDR
now i'll continue installing WinPho 7
I really can't Thank u enough
Click to expand...
Click to collapse
you are welcome. enjoy WP7

Hi guys,
i have the same problem. I flashed MAGLDR from DFT_LEO70_RELEASE and actually i still can't get into MAGLDR boot (i have the white screen).
Let me resume the tasks that i have done:
1) i'installed 1.66.408.1 (76641) ITA ROM;
2) with HSPL3_PKG.exe i installed 2.08HSPL;
3) i installed the 2.15.50.14 radio;
4) i installed (i suppose) the MAGLDR112 from the DFT_LEO70_RELEASE;
When the HD2 reboot i press the power button, in order to have the MAGLDR menu, but i always have the splach HTC white screen.
Please help me.
thanx in advance
Niccolo

niccolog71 said:
Hi guys,
i have the same problem. I flashed MAGLDR from DFT_LEO70_RELEASE and actually i still can't get into MAGLDR boot (i have the white screen).
Let me resume the tasks that i have done:
1) i'installed 1.66.408.1 (76641) ITA ROM;
2) with HSPL3_PKG.exe i installed 2.08HSPL;
3) i installed the 2.15.50.14 radio;
4) i installed (i suppose) the MAGLDR112 from the DFT_LEO70_RELEASE;
When the HD2 reboot i press the power button, in order to have the MAGLDR menu, but i always have the splach HTC white screen.
Please help me.
thanx in advance
Niccolo
Click to expand...
Click to collapse
I don't know exactly what u did wrong maybe u did the right steps but in a wrong order?
but u can try to do a task29, make sure u have 2.08.HSPL and 2.15.50.15 Radio then flash MAGLDR again it should work

ahmedsalem89 said:
I don't know exactly what u did wrong maybe u did the right steps but in a wrong order?
but u can try to do a task29, make sure u have 2.08.HSPL and 2.15.50.15 Radio then flash MAGLDR again it should work
Click to expand...
Click to collapse
More detail:
after the HSPL3_PKG.exe (actually i have this scenario:
PB81100 SS-BC
SPL-2.08.HSPL 8G XD
0x02
CotullaHSPL 0x20
i did a task 29, after that i installed tha last radio (2.15.50.14) and finally MAGLDR112.
When the device reboot i press the power button for 2-3 minutes but i always have the white screen
I was thinking that the problem could be that i have HD2 ProThree (in the hardware information i see in the RAM section 320MB and not 576MB); remember that i have the 2.15.50.14 radio but i haven't enabled the 576MB (RAM).
Any suggestion?
Thanks in advance.
niccolo

I have the same problem. Have you found any solution?

Same problem here!!

Hi Guys I have a factory HD2
ROM: 3.14.405.0 (04666) WWE
Radio Ver: 2.15.50.14
SPL: 3.03
Would i be able to flash my HD2 with the HSPL3 - i press the Vol Key down and the SPL ver I'm seeing is SPL-3.03.0000 XE ?
If not able to flash with this HSPL3, would I have to downgrade or use another soft? What should i do to continue with the whole process here to install WP7?
Thanks,
Alexandros

loumposa said:
Hi Guys I have a factory HD2
ROM: 3.14.405.0 (04666) WWE
Radio Ver: 2.15.50.14
SPL: 3.03
Would i be able to flash my HD2 with the HSPL3 - i press the Vol Key down and the SPL ver I'm seeing is SPL-3.03.0000 XE ?
If not able to flash with this HSPL3, would I have to downgrade or use another soft? What should i do to continue with the whole process here to install WP7?
Thanks,
Alexandros
Click to expand...
Click to collapse
you will have to downgrade by installing an earlier version of your rom. HSPL3 only supports up to SPL 2.10.

jase33 said:
you will have to downgrade by installing an earlier version of your rom. HSPL3 only supports up to SPL 2.10.
Click to expand...
Click to collapse
Hi jase33,
I've got the same ROM/Radio version (and same version of SPL). Will try to downgrade the ROM to an earlier version. Would love to give WP7 a spin!
What I would like to know is whether flashing back the manufacturers ROM would revert the SPL version to 3.03
Many Thanks in advance

need help with nand flash

i just bought this phone and i have went to a couple of these guides and i cant figure out why none of the hard spl programs are working for me i have fallow the steps and it shows up in wmdc but yet when i run the ruu utility it has a connection error ? i was told it was on android once before but idk if that is true. this is what the bootloader says
pb81120 ss-b3
spl-2.08.hspl 8g xe
0x85
cotullahspl 0x50
if any of this helps as well here it is
os version
5.2.21913
manila version
2.5.20181425.0
Rom version
3.14.531.1 (04666) wwe
radio version
2.15.50.14

Andrew.80 said:
i just bought this phone and i have went to a couple of these guides and i cant figure out why none of the hard spl programs are working for me i have fallow the steps and it shows up in wmdc but yet when i run the ruu utility it has a connection error ? i was told it was on android once before but idk if that is true. this is what the bootloader says
pb81120 ss-b3
spl-2.08.hspl 8g xe
0x85
cotullahspl 0x50
if any of this helps as well here it is
os version
5.2.21913
manila version
2.5.20181425.0
Rom version
3.14.531.1 (04666) wwe
radio version
2.15.50.14
Click to expand...
Click to collapse
Your bootloader is showing that hspl is installed.

Your HardSpl is ok.
Your Radio is also ok.
After this you try to install Magldr or CLK?
If so, what is the error?

Taco123 said:
Your HardSpl is ok.
Your Radio is also ok.
After this you try to install Magldr or CLK?
If so, what is the error?
Click to expand...
Click to collapse
it is showing that there is a connection error in magldr

What's your problem? HSPL is installed, so just go ahead and install either cLK or MAGLDR, CWM and then a ROM
EDIT: Sorry, literally seconds after your post above

does the magldr version matter the guide i was using was 13 but i keep getting connection error when it gets to the point when it puts my phone in the bootloader screen

Andrew.80 said:
does the magldr version matter the guide i was using was 13 but i keep getting connection error when it gets to the point when it puts my phone in the bootloader screen
Click to expand...
Click to collapse
Well MAGLDR 1.13 is the only one that works properly nowadays as pretty much all ROMs are flashed through CWM and (I think) only MAGLDR 1.13 supports this, plus WP7 support. Also can you connect in bootloader screen (rather than MAGLDR boot into bootloader then try to connect USB)?

Nigeldg said:
Well MAGLDR 1.13 is the only one that works properly nowadays as pretty much all ROMs are flashed through CWM and (I think) only MAGLDR 1.13 supports this, plus WP7 support. Also can you connect in bootloader screen (rather than MAGLDR boot into bootloader then try to connect USB)?
Click to expand...
Click to collapse
tried that got error 260 connection

could it be a driver problem?

[Q] is this stock htc hd2??

hey guys, i had (and still have) a non responding touchscreen on my htc hd2. I am now trying to get it back to stock to send it in, cause it still has warranty...
anyway, i downloaded winmob6.5 from the htc side, its a vodafone branding, so i downloaded the one where it says vodafone=) its a phone from germany.
I did task 29, and then installed the rom. (phone still had 2.08HSPL). afterwards i installed 2.08 SPL with hd2 toolkit.
The phone now reads:
PB81100 HX-BC
SPL-2.08.0000 8G XE
MicroP(LED) 0x05
MircoP(TOUCH) 0x50
in bootloader and:
R 2.15.50.14
G 15.42.50.11U
D 3.14.04666
when starting up.
my questions now are:
IS THIS ABLE TO BE SENT IN?
DO I HAVE TO CHANGE THE RADIO? IF SO,WHICH ONE?
ANYTHING I HAVE TO DO DIFFERENT TO MY WAY OF TRYING TO GET IT BACK TO STOCK??
help would be so much appreciated guys!
thanks in advance
(i posted this in the question and answer forum before, but no response, so im trying again here, cause i really dont wanna loose that phone for nothing...)

I think you have to change your SPL to either 3.03, 1.66 or anything other than 2.08.
Because as far as I know, that SPL you have is for T-mous only, having it on means you've "HSPL-ed" your device, and since your device is not a T-Mous .....
I'm not sure about the above, wait for someone more experienced to confirm.

wAVe4s said:
hey guys, i had (and still have) a non responding touchscreen on my htc hd2. I am now trying to get it back to stock to send it in, cause it still has warranty...
anyway, i downloaded winmob6.5 from the htc side, its a vodafone branding, so i downloaded the one where it says vodafone=) its a phone from germany.
I did task 29, and then installed the rom. (phone still had 2.08HSPL). afterwards i installed 2.08 SPL with hd2 toolkit.
The phone now reads:
PB81100 HX-BC
SPL-2.08.0000 8G XE
MicroP(LED) 0x05
MircoP(TOUCH) 0x50
in bootloader and:
R 2.15.50.14
G 15.42.50.11U
D 3.14.04666
when starting up.
my questions now are:
IS THIS ABLE TO BE SENT IN?
DO I HAVE TO CHANGE THE RADIO? IF SO,WHICH ONE?
ANYTHING I HAVE TO DO DIFFERENT TO MY WAY OF TRYING TO GET IT BACK TO STOCK??
help would be so much appreciated guys!
thanks in advance
(i posted this in the question and answer forum before, but no response, so im trying again here, cause i really dont wanna loose that phone for nothing...)
Click to expand...
Click to collapse
+1 to what Marvlesz said, the SPL version needs to be 3.03. I think 1.66 is only stock for the older ROMs with .51 radios, but on ROM version 3.14 the correct SPL is definitely 3.03.

Aren't HSPLs replaced to stock ones (SPLs) when installed signed rom? For example stock HD2 has SPL 3.03. You install 2.08 HSPL After fun with Android you flash stock rom. All changes caused by flashing Android and HSPL are restored to defauld SPL 3.03 That's what I think and remember. Check that.
If not, then download http://forum.xda-developers.com/showthread.php?t=966228 this and flash SPL 3.03

kubekpop said:
Aren't HSPLs replaced to stock ones (SPLs) when installed signed rom? For example stock HD2 has SPL 3.03. You install 2.08 HSPL After fun with Android you flash stock rom. All changes caused by flashing Android and HSPL are restored to defauld SPL 3.03 That's what I think and remember. Chech that.
Click to expand...
Click to collapse
Yes, you are correct. But if you re-read his post, you'll notice that he said he had installed SPL using the NAND toolkit, which gave him (or he chose) SPL 2.08 (only for T-mous).
Whereas flashing his "original" stock ROM via sdcard would've definitely restored his device back to complete stock.

first of all: thanks guys!
@kubekpop i downloaded hspl4 from DFT and installed hspl 3.03.
the phone now reads:
PB81100 HX-BC
SPL-3.03.0000 XE
MicroP(LED) 0x05
MicroP(TOUCH) 0x50
in bootloader and
R 2.15.50.14
G 15.42.50.11U
D 3.14.04666
when starting up.
What do you guys reckon? ready to be sent in? what about the radio - leave it?
@Marvlesz, I didnt install from SD because i dont have a touchscreen nomore. and i though installing the original RUU via MAGLDR doesnt make sence? so thats why i just plugged it in the pc and started it from there=)
cheers

Yep, that's fine now

But installation from SD doesn't need touchscreen. You just need nbh file (you can take it from temp files after running installer on PC - while it is still running search on drive C:/ [or other system partition] file ruu_signed.nbh And this should be in temp), formated SD without any partitions other than Fat32 (one). You rename ruu_SIGNED.nbh to leoimg.nbh and put it in SD. And via bootloader. But this what you have is enough

yeah nice, ill send it in on wednesday then.... Thanks again guys!
@kubekpop, well thats good to know, but if my phones is ready to be send in like this, ill just leave it that way=) thanks though!