I think I bricked my Cellular South Vogue :( - Touch CDMA General

Hi I have a htc touch celluer south and i ran the unlock.
it has slp-0.41 coKe then i ran a custom firmware ant it will never start up.
I tryed anything i could whent to htc web got it from there and it wouls freeze up at 11% need help sorry im a new with this stuff.
did a custom firmware for the 5th time now it says no radio and wont start up.

What stock rom where you running before hand? Was the phone already GPS enabled? Can you still reach the tri-color boot screen? If so, try reflashing to stock to at least restore function to the phone.
This thread will prob be moved.

I can get it into the tricolor screen .
windows mobile 6
I tryed stock firmware and would freeze up at 11%
Was the phone already GPS enabled? I don't have a any idea.;( it has data.
Thanks

You unlocker you use depends on weather GPS has been enabled on the phone or not. You used the non-GPS unlocker, but you may have a GPS enabled phone!
What is the full file name of the stock rom you are attempting to use? The full file name should have the rom verison and radio version. I'm not sure how much I can help, but after the admins move this thread to the right forum, you should get some good advice from people with experience.

Earl123676 said:
I can get it into the tricolor screen .
windows mobile 6
I tryed stock firmware and would freeze up at 11%
Was the phone already GPS enabled? I don't have a any idea.;( it has data.
Thanks
Click to expand...
Click to collapse
What are you trying to do. you have to be more specific are you trying to unlock with 2.31 Try and put it into bootloader mode And then flashed window 6. once again . But when it reaches 10 percent it will disconnect and connect again so be patient and just leave it alone

I was trying to put windows mobile 6.5 on.
did not use right unlock.
cannot get into any operating system
stock firmware from htcs web site when gets to 11%
will freeze then go back to tricolor screen and ROMUpdateUtility will error. ;(
custom firmware by NFSFAN will finish but phone will not load operating system stuck at Smart mobility screen in corner it says NO RADIO.
HTC Touch (US Cellular)-RUU_Vogue_4350_US_Cellular_WWE_3.01.573.4_Radio_435020_3.42.30_AM_NV_USC_1.32_PRL15052_0528_Ship.exe
Thanks

Maybe I Can Help
I´ve had the same issue. Firstable, you need to get a good ROM for the HTC Touch like these ones:
http://forum.xda-developers.com/showthread.php?t=426540
download the one you like in the ".nbh" format. Then you must find and download a program called "MTTY v.1.42".
When you get it, go to Activesync settings in your PC and disable "allow USB connections" box. then go to Task manager and kill the activesync process in Windows.
Now connect the phone to the PC. run MTTY. Select "Port:USB" .
where it says" flow control" change the parameter to: RTS/cts
Press OK and leave it like that. Dont close anything.
Finally go to the ROMupdate utlity and flash the new rom normally. If you have any doubt add me at: [email protected]

Ok Thank you I'll give it a try in the morning.

!!
Earl123676 said:
Ok Thank you I'll give it a try in the morning.
Click to expand...
Click to collapse
http://forum.xda-developers.com/showthread.php?t=426540, that's a GSM!!

Is my phone a gsm model ;~ It came from south central.
It errors out and says This NBF file cannot be used for your pda phone. Please get anwer NBF file. when trying to do rom update.

Earl123676 said:
Is my phone a gsm model ;~ It came from south central.
It errors out and says This NBF file cannot be used for your pda phone. Please get anwer NBF file. when trying to do rom update.
Click to expand...
Click to collapse
Go here:
http://forum.xda-developers.com/showthread.php?t=873446
Vogue is a CDMA.

?? That dose not help I just want to do anything to get my phone working.
No firmware seems to work.
Need help On tricolor screen right now.
with coKe 0.41
Is that the wrong unlock
is that why custom firmwares install but never start up,says no radio.
left it all night still the same can't do any unlocks cannot get any operating system to boot clear up original one from htc while installing firmware it allways freezes up at 11%.
This sucks NEED HELP OK!!

I would try using either my XevRev ROM or NuVogue (until I build A South Cell ver later tonight . I'm not just saying that because I made it either. lol You can find the link in the forum you posted this thead in (I'm on my Touch Pro2 atm, getting direct link is a pain... will update in a few mins).

XevRev ROM or NuVogue.
XevRev
Sprint PCS (Build #71)
Verizon Wireless (Build #72)
Telus (Build #73)
Alltel (Build #77)
Bell Canada (Build #79)
There is no celluler south ?
Can't try that .
NuVogue.
Tried it th i did not !!
Ill give it a try for now.Which
NuVogue 8.0 or it dose not matter. i'll try 8.0 for now
This phone dose not have sim card
device VOGU100 is CDMA OK.
Just a reminder celluler south,South central same thing.
when there is a phone that says celluler south It shows
Up at south central. Not very famous. Its located in southern UTAH
THANKS
OK
NuVogue 8.0
Dose not work.;(
http://www.socen.com/ South centrals website
https://www.cellularsouth.com/cscom...2070029&WT.srch=1&WT.mc_id=ppc_Google_D-Brand Celluler Souths website
There is some thing wierd here......

After thinking about things, I see why you can't flash the stock rom: You do not have a Cellular South rom to flash to. US Cellular is not Cellular South from all the research I did.
The problem is I was unable to locate a Cellular South shipping rom. A shipping rom is what you would normally want to use to reflash the phone and "relock" it back to true stock easily.
Now, one option would be to attempt to flash just a non-GPS radio, however that could brick your device. ImCoKeMaN has more information on that in this thread on ppcgeeks.
I would recommend that you start a thread here on ppcgeeks, where you may run into some others with more expertize. I'd also link to this thread just in case they need more information. I would also create a detailed thread name like "I think I bricked my Cellular South Vogue" (I'd recommend changing the name of this thread to reflect that as well).
Now, my idea would be to use MTTY and try and figure out what radio is installed (if you can even do that, I seriously have no clue), contact Cellular South for a true stock rom for your phone, and find out what radio was installed on the phone (1.x or 3.x series radio). Since the .41 unlocker didn't work, that think that means you may have had a 3 series radio.
Without knowing anything about how the roms for Cellular South are, your better off either contacting Cellular South and ask them for their stock software (and if you do get it, share it with the world dude, cause no one has it!), and/or try PPCGeeks for more advanced advice.
ImCoKeMaN hangs out on the IRC chatrooms #ppcgeeks and #ppckitchen on (chat.freenode.net) freenode. If you can catch him, he may be able to offer radio advice on the Vogue. You could also start a thread on PPCG and point it out to the guys in that channel, lots of knowledgeable types that have been doing this stuff for years.
So long as your getting the tri-color screen, I think you can get the phone working, so don't loose hope!

well OK Is ther any one else here smart.I'll talk to south central guys when i can to see if they will say go find the dump or whatever.
it says on box HTC------------------------------------6900 South Central
Oh I used .41 unlocker it worked look at pic it was .36 or somthing.
Thanks any way.

@OP,
Let me try to jump in here before you do anything else. As you can obviously flash roms (you can get to bootloader), basically you used, as stated earlier, the wrong unlocker. Before you can flash anything, you will need to flash back to stock. You mentioned that you have tried doing this and you get an error at 11%.... what kind of error do you get? (error code). The only thing that could have fried your radio would be to have flashed it back from a 3.xx.xxx radio into a 1.xx.xxx, which is what ImCoKeMaN describes over at Howard Forums. The .41 is an unlocker for non-GPS Vogues from what I understand, but this is not protected from overwriting, so flashing a stock should get you back up and running.
After you are done flashing back to stock, take a look at my Vogue flashing guide (link in my signature).

Ok Thanks I need to get hold of a stock rom I was using Us Celluler.
Oh on error my phone would go to tricolor screen at 11% then it would have a commnuication error on computer
Need celluler south or south central just whatever I'll Chat with South central guys
One i know well .Thanks

Earl123676 said:
Ok Thanks I need to get hold of a stock rom I was using Us Celluler.
Oh on error my phone would go to tricolor screen at 11% then it would have a commnuication error on computer
Need celluler south or south central just whatever I'll Chat with South central guys
One i know well .Thanks
Click to expand...
Click to collapse
http://shipped-roms.com/index.php?category=windows mobile&model=Vogue
Go here. The rom that you are looking for is the last one on the list. That will flash a 3.xx.xxx radio as well, so it should give you GPS capabilities too.
As far as the error, I am looking for an error code from the PC. (I am guessing it is 228, but I could be wrong)
BTW, I am moving this thread to General as it isn't development.

OK Thanks.

Related

Help with charmer

Hi,
I seem to have made my MDA compact II a brick. I was having problems hard reseting it (Format FAT failed) so I tried upgrading to a different firmware.
I now have the RUU_Prophet_2151327_21513121_021921_DOP_ASIA_WWE_Ship-NoVendorID
firmware on it. This is not good as it is for the Prophet, although it says in the Wiki that this should work. Anyway I can now hard reset the phone, so all I need to do is flash the TmobileUK firmware back on it. The only problem is that it doesn;t let me do it. It says error:296 upgrade only.
Anyone any ideas?
cheers.
extract the contents of the t mobile package using win rar
download
ftp://xda:[email protected]/Prophet/Tools/ROMUpdateUtility-NoVendorID.zip
and put in the same directory and run.
It gets to 1% then says invalid command, not for this phone.
Latest T-Mobile ROM is at http://www.tm-phonedownloads.com/download_manager_mda_com2.html
very stable, much better than the original shipped ROM
Finally got it back.
If you have a T-mobile MDA II (Charmer), then Flash it with a Prophet ROM, the only way I could get it back was to use the following:
RUU_Charmer_100_100_049_CHS_Ship.rar
typho5 -x nk.nbf
Then created a new nk.nbf with the output using nb2nbf.
I then Flashed this with Wizard_RomUpgradeUtility_noID
And miracle it started. I quickly CID unlocked it and am now flashing with latest T-mobile.
My problem was that the Rom Update programs wouldn;t read version 2.xx ROMS.
Anyway it has just finished and looks fine. Thanks for everyones help, now I just have to get my SD wifi card working.
How do you do it
Hi I just got a MDA compact II from T Mobile UK I would like to upgade the ROM but its all very new to me since you know what you are doing can you post an idiots guide to the process.
Hope you can help
Hi, it depends what Rom you want to upgrade it to, the latest one from T-mobile is pretty good. There is an unbranded one (no T-mobile logos or suchlike) or there are Roms in different languages. It depends why you want to change the firmware and what to.
I suppose I don't really know the problem is as I just got the thing did some searching and came across this site read your post and thought i want to do this maybe you have some suggestion. Also I tried the RUU mentioned in an earlier post but it I can't update when I get to the from/to screen it tells me I will go from 2.6.2.110 to 2.6.2.110 I was expecting to move up.
daveh1171 said:
I suppose I don't really know the problem is as I just got the thing did some searching and came across this site read your post and thought i want to do this maybe you have some suggestion. Also I tried the RUU mentioned in an earlier post but it I can't update when I get to the from/to screen it tells me I will go from 2.6.2.110 to 2.6.2.110 I was expecting to move up.
Click to expand...
Click to collapse
Sounds like you are running the latest version. Is there a problem with the phone? If the phone works fine, I would just unlock it using lokiwiz02b (So you can use any network card) and then EnableRapi (So you can run unsigned code) then CID unlock it using awizard (so you can use any Brand/Language of ROM).
If you have no problem with the firmware I would leave it alone.
Hi,
Yep, I'm in the same situation, why does the prophet firmware load onto the charmer without erroring? !!!
Anyway, I have a copy of RUU.rar but I'm having problems working out what I need to do to it between unpacking and flashing the phone (i.e. the typho5 bit and then the nb2nbf).
Can someone please help me out?
P.S. The phone just sits at a black screen that says 'Dopod' across the front at the moment
Can anyone tell me how to 'force' a downgrade of firmware? I've got what appears to be the right firmware from FTP but it won't over write the incorrect version 2 installation as the uploader software thinks it's later therefore better.
There has got to be a better option from the command line surely?
HELP phone is dead
Chirpy said:
Can anyone tell me how to 'force' a downgrade of firmware? I've got what appears to be the right firmware from FTP but it won't over write the incorrect version 2 installation as the uploader software thinks it's later therefore better.
There has got to be a better option from the command line surely?
HELP phone is dead
Click to expand...
Click to collapse
Progress, but now it works only from the charger so the shipped ROM upgrade won't work as it reports the battery as being at less than 50%.
Anyone know how to force a ROM upgrade or where I can find the right ROM files to use awizard to do this?

Dutch to english ROM

Hey guys,
Im another newbie, but who is actually scared of screwing up the phone. I have the Tmobile MDA compact III obviously, and the information page looks like this:
ROM version 1.13.114.1 NLD
ExtRom version 1.13.114.101
Model nr ARTE 110
CPU OMAP850
Im not so sure what this information tells you people who are knowledgable about this, however can I safely use the customised powermap file from this website's ftp (ftp://ftp.xda-developers.com/Artemis/Customized_ROMs/) to change the phone to english?
What are the procedures EXACTLY please, and what problems should I expect.
Another thing, what is CID lock, and how can I see if mine is or not?
I checked most of the threads, so I am knowledgable about this issue a bit, however because none of the topics were specifically about the Dutch version I wanted to make sure. Thank you a lot for your help...
1. you have to CID unlock your phone. only real solution is imei-check website, and that will cost you $40. this will prevent MANY of the problems with installing ROMs
2. don't do updating on Vista PC, use XP or older
3. follow on screen instructions of your chosen ROM update utility. don't panic if it takes too long and looks like the update process has "freezed". make yourself a coffee and let it finish installing.
4. enjoy!
PS... i strongly suggest you read as much as you can on this forum before doing any upgrading.... then you'll know what to expect.... and of course, don't forget that only YOU are responsible for anything that happens to your device, good or bad... good luck!
hey dim4x4,
thanks for the post, I appreciate it. However is the exe file I mentioned (customised power map) the right one? i know there are a few options to chose from, like the 3 options of the pdamobiz.com website. While im not too clear of the main differences, the general concensus on the forum is that the powermap is preferred, and has a lot of nice things. Is there a better one? perhaps on a different ftp. Maybe if you have one you can send it to me.
Another thing, if it dont work, or works and I dont like it, can I get back to my original ROM, the dutch one from the tmobile dutch file on the ftp site as well?
Thanks
1. Personally, I use PDAmobiz Lite version. Powermap version has a map of Thailand which I don't need. "A lot of nice things" for my purpose is a lot of unnecessary stuff. If I need something I can install it myself into RAM or storage card. You have to choose the version which suits you best.
2. Everything is on this server. You have to register to log in http://www.wm-gurus.com/registration/signup.php
3. I went back and forth with different ROMs (versions, languages, etc.) without any problem until I found more or less what I want. Please note, my device is CID unlocked by imei-chek.
Good luck!
Urgent Help
I tried the powermap version of the ftp. This is exactly what I did:
I connected the phone and established contact through activesync, then I started the exe file. The DOS windows opened, and then it started initialiying, and the process started. It said that it will take 15-30 mintues, and the process has started. So far im sure everypone is familiar with those. However, I waited about 35-40 minutes, and still nothing different on either screens. The DOS window said however that if nothing starts I should reset the process. I tried but didnt work. At that time I tried to reset the phone and now it is stuck in the startup screen. All I see on it is the IPL/OS data, and it is not moving further.
Please help, what do I do now?
So this is what I did so far....
1. Flashed with PDAMobiz_Dopod_P800W_AKU301_v1.1.2_PowerMap.exe (with device on Today screen)
2. The process started and stuck on "uploading file [don't remember] and as the instruction said I reseted the phone after 30 minutes.
3. All there is on is T-Mobile splash screen, version infos and that's it.
5. Tried to flash again in bootloader mode but the device was not visible by PC
How do I go from here? Maybe I need to flash the original rom version of the phone. I have the dutch tmobile mda compaxt III, but with the dutch ROM version on the ftp of this site is scary, because there are too many files and have no clue which one to flash.
Any suggestions?
There is no Dutch T-Mobile ROM available yet.
You could try the English T-Mobile ROM (art_tmouk_11311001_024990_wwe_ship.exe), which is available on this site: http://www.wm-gurus.com/registration/signup.php
There's a chance this ROM will work on your Dutch T-Mobile phone, if the signature is correct (I assume your phone is still CID locked).
Read this link http://wiki.xda-developers.com/index.php?pagename=Artemis_Resets on how to enter the bootloader of your phone.
mRmAGIC...
I Tried That Already; But I Got An Invalid Id: So I Dont Know What Else So Far: Do You Think I Have To Cid Lock The Phone To Be Able To Try The Other Versions?
tghobar said:
I Tried That Already; But I Got An Invalid Id: So I Dont Know What Else So Far: Do You Think I Have To Cid Lock The Phone To Be Able To Try The Other Versions?
Click to expand...
Click to collapse
CID unlocking isn't possible if your phone isn't working.
If you don't have your original rom, you have to contact your provider to repair it.
try from bootloader screen
Hi I also did as u did but with a hards reset in the beginning.And it worked fine.read somewhere that if u dnt do a hard reset you could get into problems.If u can try to go to bootloader screen and try to flash from ther.
flashing from the bootloader screen gives me an error, the file cannot recognize that a phone is connected to the PC. that is the biggest problem I think.
DO you know how to flash the Tmobile NL version on the ftp. there is one that I dont know how to use

Please help - bricked XDA Orbit II

Hi, first post on the forum so please be gentle with me....
I have an XDA Orbit 2 which was until last Thursday working fine with the last official upgrade from O2 (Win 6.1, no idea about all the other stuff).
Whilst using the phone last week it suddenly died in the middle of a conversation. It wouldn't power on at all. I took out the battery, waited a couple of minutes, put the battery back in and switched it on. All that happened was the phone displayed the 4 colour screen with "POLA200 SPL-3.13.0000 CPLD-2" in the red section and "Serial" in the white. I repeated the battery removal exercise a few times, waiting for increasing lengths of time but nothing changed.
I had a fairly long search through the forum and have tried for a few hours now going through the various fixes suggested but I am getting nowhere.
It won't hard reset, all that happens is the message "No Image Found" appears for a very short time and I then get stuck on the 4 coloured screen with the message above.
The same thing happens if I try just putting the thing in bootloader mode.
I can't use any of the official O2 rom upgrades as the phone because all the PCs I've tried connecting to it won't recognise it over a USB link.
I've tried connecting to it using mtty, again on several PCs, but I just get a message "USB port can not open". Just in case I've uninstalled Activesync on one PC and got the same answer.
The "how to flash you polaris using the microSD card" originally looked useful but I have some problems with it.
The first is that I need HardSPL installing on the device, which I can't do because I can't get to it.
The second will be down to me not knowing where to look, but I can't find a ROM to download and copy to the microSD card as POLAIMG.nbh. I did manage to find a Win6.5 one (the HTC Polaris - PDaviet rom wm6.5 manilla 2d (core 23004) by tranminhman one) which I thought I'd try. I guess the idea was that if I could just get something working I could always reflash it again with a different ROM or maybe apply the o2 upgrade. Unfortunately the image was password protected and I couldn't find the password in the thread.
I'm kind of at a loss now so any help would be appreciated.
Cheers
Hey,
Sorry i can't help much you'll need to do a lot of reading and troubleshooting...usually it's the onyl way to solve it by trying all options.
I'm just posting this message to bump it up in this forum, but more importantly you should be posting in the Iolite section for help with that specific device especially if you're trying other ROMs.
Also if it died on you and you haven't begun to flash it, can't you send it to the service for them to fix it for you? That way you can rule out any hardware malfunction.
Best of luck!
Alan
Did you do soft reset
alanazar said:
Hey,
Sorry i can't help much you'll need to do a lot of reading and troubleshooting...usually it's the onyl way to solve it by trying all options.
I'm just posting this message to bump it up in this forum, but more importantly you should be posting in the Iolite section for help with that specific device especially if you're trying other ROMs.
Also if it died on you and you haven't begun to flash it, can't you send it to the service for them to fix it for you? That way you can rule out any hardware malfunction.
Best of luck!
Alan
Click to expand...
Click to collapse
Bit in bold er... cant quite understand why in iolite section as the xda orbit 2 is the rebrand htc touch cruise => htc touch find. Its in the right place.
On the side of what to do i the ony thing i can think of would be mtty and if that didnt work then try to reflash the official o2 6.1 release and see what happens when you try to do it.
You cant try to install any 3rd party roms they jsut wont flash as you dont have hard spl installed and cant do that until you have it running again.
Try the above and see what happens...
Hi Nik
I have tried just about every kind of reset, nothing has worked.
Hi Alan
If I can't get it sorted any other way I'll probably send it off somewhere but I'd like to have a go at fixing it myself. It will at least be a bit of fun!
I take then that I've posted this in the wrong forum. Oops, apologies.
Jon
You have not posted in the wrong forum look at my signature!
Hi jon,
Conclusion from post 1,
1) Uncompleted flash with new ROM or hardware problem (half way die)
2) Unsuccessful flash Hard SPL (cannot see Olinex 2.2 wording during bootloader)
3) Your PC & PDA fail to connect via USB (serial wording appear during bootloader)
Try this method,
1) Get shipped ROM from HTC web site, key in your country & serial behind battery
1a) Extract shipped ROM by WinRAR , take RUU Signed.nbh
2) Rename to POLAIMG.nbh put inside SD card, "flash using SD card"
3) Make sure your battery power more than 50% cause it take about 2 hours
Good luck, my friend
[Your request Password: TranMinhMan]
Nik Ahmad said:
Hi jon,
Conclusion from post 1,
1) Uncompleted flash with new ROM or hardware problem (half way die)
2) Unsuccessful flash Hard SPL (cannot see Olinex 2.2 wording during bootloader)
3) Your PC & PDA fail to connect via USB (serial wording appear during bootloader)
Try this method,
1) Get shipped ROM from HTC web site, key in your country & serial behind battery
2) Rename to POLAIMG.nbh put inside SD card, "flash using SD card"
3) Make sure your battery power more than 50% cause it take about 2 hours
Good luck, my friend
[Your request Password: TranMinhMan]
Click to expand...
Click to collapse
Thanks Nik
I've had a bit of a look round the HTC site and couldn't see a ROM to download so I've asked their technical support people if there's anywhere to download it.
Fingers crossed they'll help.
Jon
jonfsharp said:
Thanks Nik
I've had a bit of a look round the HTC site and couldn't see a ROM to download so I've asked their technical support people if there's anywhere to download it.
Fingers crossed they'll help.
Jon
Click to expand...
Click to collapse
Try to get official HTC ROM here, Select WWE (405) CID_001 for your country.
Good luck my friend
have u tried this?...
turn off, pull out the battery, then put it back, charge ur phone till the battery indicators shows green (which mean it's already fully charged) then... power on ur device.
it looks like a dumb suggestion , but... i have had a same situation
(HTC KAISER, not Polaris).
if it doesn't work, then try to upgrade with a POLAIMG.nbh (take it from official HTC ROM)
in a 2G FAT32 microSD root directory.
Nik Ahmad said:
Try to get official HTC ROM here, Select WWE (405) CID_001 for your country.
Good luck my friend
Click to expand...
Click to collapse
Thanks Nik
Much appreciated.
Downloaded the ROM as suggested, unzipped to the SD card, renamed the image to POLAIMG.nbh, stuck it in the phone and things got slightly more interesting.
In bootloader mode I now get a bit further. I get a grey screen which says "Loading ..." then "Checking...." then "00028002 Not allow". It then goes back to the four coloured screen as before.
However, does the fact that it is trying to read something mean that I have just got the wrong file?
I'll try a few more and see what happens.
Thanks once again, your help is greatly appreciated.
Jon
Hi oza
Yep tried all the battery pulling out stuff but got nowhere.
The ROM thing on the SD card gets further. I extracted the ROM from the official O2 upgrade, stuck it on the card and renamed it POLAIMG.nbh.
If I put the phone in Bootloader mode I now get even further than before. I get a grey screen with:-
POLAIMG.nbh -
RADIO_V2 -
BOOTLOADER -
SPLASH1 -
OS -
Press power button to start update image
Press action button to cancel update image
If I press the power button
I get an "Update In Progress" message and a progress bar.
After about 4 minutes I get a full progress bar and :-
POLAIMG.nbh - OK
RADIO_V2 - OK
BOOTLOADER - OK
SPLASH1 - OK
OS - OK
Update complete
UPDATE SUCCESS
And that's as far as I've got so far.
If I take the SD card out and try a hard reset I just get stuck on the 4 coloured screen I got before, but with no No Image Found message.
I get the same thing with bootloader mode and when I just remove the battery.
If I put the SD card back in I can go through the update process but I can't do anything
else.
So, have I actually made any progress? I'm not actually sure what I have updated and what state the phone is in at the moment. Is the fact that this didn't work an indication of a hardware failure and I should send it off somewhere.
Any advice on next steps would be good.
Jon
what is ur bootloader screen says now?
IPL...
SPL...
Before you can be helped you need to supply this information:
What rom were you using when it died?
What SPL are you using?
You used MITTY and fixes so I assume you're not a complete nunce and have hard spl on your phone, so on that assumption and ONLY if you have hard spl on your phone, try this:
If it isnt a hardware problem, then Its possible you have a dodgy radio flash issue - normally that would have been caused by a bad flash, but you indicated that this happened in use.
Provided it isnt a hardware, to fix this you need to either flash the radio (less reliable, but try it) rename the radio file to POLAIMG.nbh as directed before and stick on SD card.
The other thing to try is to flash a rom with a radio INCLUDED in it. Try and avoid fancy 6.5 beta roms and stick to 6.0 and 6.1 basic roms.
I believe Chavonbravo's VLIT roms come with the radio so try that. Its listed in the forum. I'm not providing links as I dont know what radio you were using and you really need to go for like to like or close. My preference is 1.59.44.02 radio rom if you find one.
Let us know how you do.
Lastly what radio and rom did you have?
Try this one M-AMINES if the radio you had was a 1.59.xx radio as it has the radio included.
if it was a 1.65.xx radio then try the VLIT naked rom.
oza_crazy said:
what is ur bootloader screen says now?
IPL...
SPL...
Click to expand...
Click to collapse
Hi Oza
Exactly the same as it did when it first broke. I get the 4 coloured screen with "POLA200 SPL-3.13.0000 CPLD-2" in the red section and "Serial" in the white.
No idea what the IPL is or was I'm afraid.
Jon
bally3 said:
Before you can be helped you need to supply this information:
What rom were you using when it died?
What SPL are you using?
You used MITTY and fixes so I assume you're not a complete nunce and have hard spl on your phone, so on that assumption and ONLY if you have hard spl on your phone, try this:
If it isnt a hardware problem, then Its possible you have a dodgy radio flash issue - normally that would have been caused by a bad flash, but you indicated that this happened in use.
Provided it isnt a hardware, to fix this you need to either flash the radio (less reliable, but try it) rename the radio file to POLAIMG.nbh as directed before and stick on SD card.
The other thing to try is to flash a rom with a radio INCLUDED in it. Try and avoid fancy 6.5 beta roms and stick to 6.0 and 6.1 basic roms.
I believe Chavonbravo's VLIT roms come with the radio so try that. Its listed in the forum. I'm not providing links as I dont know what radio you were using and you really need to go for like to like or close. My preference is 1.59.44.02 radio rom if you find one.
Let us know how you do.
Lastly what radio and rom did you have?
Click to expand...
Click to collapse
I've not been a big modifier in the past so it was just using the bog standard O2 software from the O2 website. The name of the file is "RUU_Polaris_O2_UK_3.13.206.0_radio_sign_25.85.30.07_1.59.42.15_Ship.exe" so I presume that there can be information gleaned about things like the SPL, ROM and radio versions?
Not a complete nunce, no, but so very far away from being comfortable with all this. This post was a result of a good few hours trawling through the forums looking for help. Anything I have done has been the result of a post on this site and I am very grateful that there are people willing to share their knowledge.
Anyway, as for hard spl, nope it isn't installed. I'd never needed anything like it before the phone died and now that it has died I can't get onto it to install anything.
Yes, this happened right in the middle of a conversation after a good year or so of normal day to day use. As I said, I haven't needed to make any changes to the phone so the only thing I've ever done is upgraded it with software from the O2 site.
I'm beginning to suspect that without Hard spl my options are very limited and pointing towards either sending it off for costly repairs or just binning the thing. I am probably wrong but I'm guessing that the fact that I don't have it installed is the reason why nothing is happening with the "Update in progress" stuff that is happening now.
Radio & ROM, as above. Whatever the O2 update provided. From the filename radio would be 1.59.42.15.
Many thanks
Jon
jonfsharp said:
I'm beginning to suspect that without Hard spl my options are very limited and pointing towards either sending it off for costly repairs or just binning the thing. I am probably wrong but I'm guessing that the fact that I don't have it installed is the reason why nothing is happening with the "Update in progress" stuff that is happening now.
Radio & ROM, as above. Whatever the O2 update provided. From the filename radio would be 1.59.42.15.
Many thanks
Jon
Click to expand...
Click to collapse
Well whatever you do dont bin it, we can always use it on the Android project if you decide to go that way.
Ok.. so lets see.. the phone is not picked up at all in windows?
If that is the case, if even a serial connection cant be made then theres issues. At this point, I would disregard all the other advice as it only applies to a hard spl device unfortunately. SD card flashing and all other radio rom flashing will only work with hard spl as far as I know - definitely safer for certain and you dont want to wreck a repairable device.
I take it, its not under warranty, for your mention of costly repair.
The important thing at this stage is a serial or usb connection from a Windows PC. I think I have heard of forcing this connection by opening the device but this would really be in the realms of profficient repairer or enthusiast.
I'll have a look but also do some searching yourself for making a connection to a Windows PC and forcing an SPL onto a phone.
I dont know whether anyone's ever managed to HardSPL a phone using a memory card? Just a thought...
Who would have known.. have a read of this and see if you can follow it up regarding the spl through sd card ..
http://forum.xda-developers.com/showpost.php?p=3273438&postcount=7

Flashing HD2 with WWE ROM

Hello,
I want to flash my device with 1.66.707.1 rom. I can't download it via HTC official page.
Now I have few questions. According to that I couldn't download it from HTC official page in my country because I've got inappropriate S/N. May I install it on my radio if I supply good (fake) S/N to official HTC page?
I even didn't tray to do this because I'm afraid I can turn my HD2 a into brick.
I don't care about language. I think that after flashing ROM I can download a proper language pack.
Greats.
invalid serial means your phone is vendor locked. (eg t mobile, vodafone or whatever)
even if you download using a different serial the upgrade will fail saying "vendor id mismatch" or something similar.
in theory you need to wait for your vendor to release the update, however in reality installing hspl will allow you to instal the update without getting the error.
go read the hspl threads.
Easy to sey .
It's my first Windows Mobile based phone. I've never installed rom, and yet a cooked one.
I've have some bugs about which I've read on this forum. Those are:
* lack of virtual keyboard while creating a new text message (or any app which need it)
* error while starting digital camera.
All of that disappear after soft reset. That's why I want to install the newest rom.
To not start a new thread is there any way to find out if the rom which I downloaded from HTC suits to my phone? S/N is correct. If I start RUU it will start flashing my device, yes?
Another question. Is it true that every HTC Leo has 576MB RAM but it is locked down?
read this then, it has all the info you need on flashing your phone...
http://forum.xda-developers.com/showthread.php?t=609477
once HSPL is installed you can download an official WWE ROM from this thread and run it as if it were an official ROM for your phone...
http://forum.xda-developers.com/showthread.php?t=623283
y0yster said:
Easy to sey .
It's my first Windows Mobile based phone. I've never installed rom, and yet a cooked one.
I've have some bugs about which I've read on this forum. Those are:
* lack of virtual keyboard while creating a new text message (or any app which need it)
* error while starting digital camera.
All of that disappear after soft reset. That's why I want to install the newest rom.
To not start a new thread is there any way to find out if the rom which I downloaded from HTC suits to my phone? S/N is correct. If I start RUU it will start flashing my device, yes?
Another question. Is it true that every HTC Leo has 576MB RAM but it is locked down?
Click to expand...
Click to collapse
As EddyOS stated, go read my flashing guide THOROUGHLY!!
1. Install HardSPL on your device (best done using WindowsXP or Windows7 32bit).
2. Download the Rom you require from the download site provided and flash using the instructions provided in my guide.
3. Enjoy your new phone
Once you have HardSPL on your phone it will be protected from bad flashes and you will be able to flash stock or custom roms or radios as and when you require. HardSPL is definitely reccommended as it has probably saved hundreds of phone from being turned into paperweights when flashing a bad rom or flashing incorrectly.
If you want to try a custom rom then I would definitely recommend the one in my signature but its totally upto you what you decide to put on your device.
With regards to the 576MB Ram it does seem that its actually accessible but only using the newer 2.02 Roms with specific Radios. This has been tested and verified. It wont be accessible on a 1.66 stock rom though.
Hello,
I tried to flash my device witch rom which is on htc official page.
When I was flashing something went wrong and on 24% upgrade have broken. I did what was write on the program but all the time I have 4 strips red, green, blue and white. Before I turn on the device I have sign of warning.
What I have to do now? Is my phone dead now?
Please answer as soon as you can.
y0yster said:
Hello,
I tried to flash my device witch rom which is on htc official page.
When I was flashing something went wrong and on 24% upgrade have broken. I did what was write on the program but all the time I have 4 strips red, green, blue and white. Before I turn on the device I have sign of warning.
What I have to do now? Is my phone dead now?
Please answer as soon as you can.
Click to expand...
Click to collapse
- What ROM were you trying to flash and what ROM version (and language) do you have on your device?
- Is your device Branded?
- Did you flash HSPL?
- Did you see a progress bar on screen when flashing, or just the colored bars?
- When you get to the tricolor-screen (bootloader) and you connect to your PC, does it say USB after a few seconds, or does it say Serial?
- What went wrong at 24%? Did you unplug the phone, did your system crash, or were you just being inpatient?
If you answer the above questions, someone may be able to help you. Also, start by reading the stickies.
Rom was 1.48.479.1 and I wanted to replace it with 1.48.479.1 because some bugs were annoying me which I mentioned earlier.
Yes my device is branded but it doesn't have simlock.
No I didn't used HSPL because I downloaded rom from HTC using my own original S/N.
When I was flashing I saw brogress bar with HTC logo.
I have those tri-colour screen when I power on the device, but before that I have warning triangle. No it doesn't say Serial nor USB.
What went wrong. I swear I don't know. No, no, no I wasn't impatient. After it hanged on 24% I got error message from the program on PC with UPGRADE ERROR. I've tried to resume like the program said me. But without any effect. What I did was unplug; put aut battery; wait 3 seconds; put battery in; power on and plug in. I'm sure that I was doing everything right because I was following the program.
help
samsamuel said:
invalid serial means your phone is vendor locked. (eg t mobile, vodafone or whatever)
even if you download using a different serial the upgrade will fail saying "vendor id mismatch" or something similar.
in theory you need to wait for your vendor to release the update, however in reality installing hspl will allow you to instal the update without getting the error.
go read the hspl th
hi there i really need help
i have a htc hd2 uk on t-mobile tried to rom update and messed it up , things dont work , i would like to ind software to rom update even htc.com s/n not right message comes up . please help
Click to expand...
Click to collapse
If i have 1.48 and with my serial can`t download 1.66... it is recommended to install WWE 1.66 with serials posted here without HSPL? my device is also WWE and was only sim locked Vodafone. (non-branded)
If you have questions regarding rom or hardspl flashing please ask in the correct thread.
if,when you put your serial into htc website, it doesn't allow you to download, then you MUST use hspl to flash an unbranded rom.
@y0ystet. your phone is branded. sim lock its not connected to vendor lock.instal hspl and try again, same rom.
@lakhbeer, did you flash hspl first? more detail please, messed up? doesn't work?
@rayman your phone is vodafone locked.
I repeat, the htc website doesn't accept your serial, you are provider locked and that is not connected to sim lock/unlock.
I sent an e-mail to HTC about that. They said I can send the phone to them.
I found sth out. If I hold the volume down and connect the usb cable I have a message on my screen. On screen which have three colours on green I have: "Upgrade Rom code error. Please try again" And on the white I have: "Serial".
Is there anything I can do about that?
But don't say me to flash witch the HSPL. I won't do that on two reasons:
I've never do that
If I send it to service I'll void my warranty.
What would you suggest to do?
I've solved the problem .
you going to let people know for future use?
How to fix ROM error on VODAFONE UK solution
I also have a HTC HD2 bought from Vodafone.
I flashed my mobile and installed Pandora 1.4 ROM...it was always freezing my Leo every time I looked at docs tab, so I decided to install shipped Leo ROM 1.66 and that is when things went wrong, same problem as you have now, so I downloaded h**p://w w w .4shared.com/file/205652004/1bf6c7ce/RUU_Leo_Vodafone_UK_1434051_Ra.html
aka the original ROM from Vodafone UK and it is working now....but now I am no sure if I wanna try more roms because next time I can be stuck with error screen forever.....

[Q] Not suer where to start

I bought this phone three months ago knowing WP8 was coming out soon. :crying:
I see the XevRev for Spark_W stuff, radio collecctions, tons of custom rom stuff, and etc, but I'm at the point where I'm utterly confused at what it what.
I guess I'm asking where I should start?
Here is what I think might be relevant:
OS Ver: 7.10.8773.98
FW Ver: 2305.13.30202.605
HW Rev: 0003
Radio SW Ver: 1.43.00.06.14_23.17w.05.13U
Radio HW Ver: 3.2.3.D4
Bootloader Ver:3.2.230513.2
Changed DUN NAI from dun.vzw3g.com to vzw3g.com
Just got my dev unlock through dreamspark.
thals1992 said:
I bought this phone three months ago knowing WP8 was coming out soon. :crying:
I see the XevRev for Spark_W stuff, radio collecctions, tons of custom rom stuff, and etc, but I'm at the point where I'm utterly confused at what it what.
I guess I'm asking where I should start?
Here is what I think might be relevant:
OS Ver: 7.10.8773.98
FW Ver: 2305.13.30202.605
HW Rev: 0003
Radio SW Ver: 1.43.00.06.14_23.17w.05.13U
Radio HW Ver: 3.2.3.D4
Bootloader Ver:3.2.230513.2
Changed DUN NAI from dun.vzw3g.com to vzw3g.com
Just got my dev unlock through dreamspark.
Click to expand...
Click to collapse
Well, dev unlock is really unnecessary if you plan on installing an HSPL and flashing a custom rom. Then again, your OS version of 8773.98 suggest that you are running DFT or ansar's rom, but didn't install HSPL (only RSPL to flash the rom). Even with the official rom, your OS level should be 8779.8 after updating via Zune.
First, if you REALLY want to unlock the power of this phone, install HSPL using my HSPL guide for SparkW. It explains every step in detail so you can be ready to flash a custom rom.
Second, give my SparkW rom XevRev a shot for a great Tango experience. Just flash the rom, then update via Zune after setting up the phone to get the newest radio installed. It has FullUnlock and Root Tools, and is the only rom currently around that allows for the phone to be fully programmed using *228 (older roms have an older Xap Deployer package that didn't allow the programing tools to be installed).
You can ignore the radio thread and the "stock like" threads because the contents of those are now outdated with my rom being out.
Get 10+ post under your belt and you can reply to dev forum topics. I'm working on a 7.8 rom, but I won't be able to test it until my third Spark_W comes tomorrow and I transplant a digitizer into it. Maybe since I'm taking it apart I'll also upgrade the SD Card on that one too? (I don't want to flash my primary phone since it's too much of a pain to get reinstalled when I need it for an alarm clock.
Before you flash another rom though, I want to ask you a few things. Do you have Unlimited data via Verizon, and if not, what plan do you have? Also, is tethering working for you NOW before flashing my rom simply by doing the dun nai change? The dun nai change should only be necessary for Unlimited data users.
I'm using factory updates. All I know is that I have my phone updated as far as I can through Zune.
We just switched from AT&T to Verizon, due to the lack of any signal across the entire house. When we went into the store they had to have their manager bring the phone all the way from Kentucky. Anyways, they had just started to push the share everything plan, but the reps acted like they weren't comfortable with those plans yet. I have a 2gb a month, but I called verizon and they disabled the DUN for my phone (as I didn't want charged one of the wifi access fees) When I enabled the wifi after I called them I got a webpage showing I could re-enable it for the $30.
I tried to do the Interop_Unlock but that seemed to not work. But I might as well wait for your 7.8 then.
thals1992 said:
I'm using factory updates. All I know is that I have my phone updated as far as I can through Zune.
We just switched from AT&T to Verizon, due to the lack of any signal across the entire house. When we went into the store they had to have their manager bring the phone all the way from Kentucky. Anyways, they had just started to push the share everything plan, but the reps acted like they weren't comfortable with those plans yet. I have a 2gb a month, but I called verizon and they disabled the DUN for my phone (as I didn't want charged one of the wifi access fees) When I enabled the wifi after I called them I got a webpage showing I could re-enable it for the $30.
I tried to do the Interop_Unlock but that seemed to not work. But I might as well wait for your 7.8 then.
Click to expand...
Click to collapse
Yeah, Interop is a pain to do unless you are running Mango v1. You could factory downgrade to do it.. but its really a big pain.
I'm aiming to have 7.8 and international language roms out by Sunday, work is guna make it difficult. Are you able to use tethering with the dun nai changed though? I'm curious because other users with metered data plans were still having issues.
If you can't use tethering even with the dun nai changed, try deploying JerryJiang's Tethering unlocker for Verizon Trophy. If you still can't tether, I think I know a final adjustment that may need to be made, and you could be a helpful test subject since JerryJiang sent me his apps source code. After I get the details sorted, I can apply the fix directly into my rom without a need for an app (and create a rom package for others to cook into their roms).
TheXev said:
Yeah, Interop is a pain to do unless you are running Mango v1. You could factory downgrade to do it.. but its really a big pain.
I'm aiming to have 7.8 and international language roms out by Sunday, work is guna make it difficult. Are you able to use tethering with the dun nai changed though? I'm curious because other users with metered data plans were still having issues.
If you can't use tethering even with the dun nai changed, try deploying JerryJiang's Tethering unlocker for Verizon Trophy. If you still can't tether, I think I know a final adjustment that may need to be made, and you could be a helpful test subject since JerryJiang sent me his apps source code. After I get the details sorted, I can apply the fix directly into my rom without a need for an app (and create a rom package for others to cook into their roms).
Click to expand...
Click to collapse
Tethering works with the internet sharing in settings. I have no issues what so ever.
I'll beta test if needed. (If it says anything im running win8x86 rtm kinda as my main os)
EDIT
Just saw how big RUU_Spark_W_S_VERIZON_WWE_2.04.605.02_Radio_NV_021 5_NV58008_RELEASE is. I have hughesnet and a 500mb daily cap. I'll have to wait till I'm at my grandparents(I'm 19) where dsl is king tomorrow. lol
thals1992 said:
Tethering works with the internet sharing in settings. I have no issues what so ever.
I'll beta test if needed. (If it says anything im running win8x86 rtm kinda as my main os)
EDIT
Just saw how big RUU_Spark_W_S_VERIZON_WWE_2.04.605.02_Radio_NV_021 5_NV58008_RELEASE is. I have hughesnet and a 500mb daily cap. I'll have to wait till I'm at my grandparents(I'm 19) where dsl is king tomorrow. lol
Click to expand...
Click to collapse
That is the rom for flashing back to stock. You'll need the older rom in the HSPL thread to downgrade the bootloader. Get both roms and back them up if bandwidth is a problem.
So, I finally got to download the RUU_Spark_W_VERIZON_WWE_1.03.605.22_RS0512_2K_4K_hybrid_new_partition_RELEASE and I got it to flash the phone, but now when I try to flash using [ROM_SPARKW][TheXev]XevRev_Beta1a_8835 the phone gets stuck at 0%. I can follow the instructions shown on the program, but it seems to get stuck at the same place.
I can just unplug the phone and turn it back on and i can get calls in the meantime, but it seems I can't proceed.
I tried the dft rom aswell, but it shows the following:
Code:
[Error Description]:
Invalid ModelID. This means that your phone not supported.
This installer supports only limited number of the phones.
SPARK, MOZART, MONDRIAN, GOLD, SCHUBERT.
If you have phone from this list, but still have this error, please contact with DFT team.
[Info]: USBWorkRSPL.cpp (235)
[Error Description]:
ModelID is 'PC402000'. Please report this info to DFT.
[Info]: USBWorkRSPL.cpp (234)
thals1992 said:
So, I finally got to download the RUU_Spark_W_VERIZON_WWE_1.03.605.22_RS0512_2K_4K_hybrid_new_partition_RELEASE and I got it to flash the phone, but now when I try to flash using [ROM_SPARKW][TheXev]XevRev_Beta1a_8835 the phone gets stuck at 0%. I can follow the instructions shown on the program, but it seems to get stuck at the same place.
I can just unplug the phone and turn it back on and i can get calls in the meantime, but it seems I can't proceed.
I tried the dft rom aswell, but it shows the following:
Code:
[Error Description]:
Invalid ModelID. This means that your phone not supported.
This installer supports only limited number of the phones.
SPARK, MOZART, MONDRIAN, GOLD, SCHUBERT.
If you have phone from this list, but still have this error, please contact with DFT team.
[Info]: USBWorkRSPL.cpp (235)
[Error Description]:
ModelID is 'PC402000'. Please report this info to DFT.
[Info]: USBWorkRSPL.cpp (234)
Click to expand...
Click to collapse
You need to install HSPL before you can flash a custom rom. After downgrading the bootloader to 1.3, you can then install HSPL. Follow my guide here for complete instructions, step by step.
GOT IT!
TheXev said:
You need to install HSPL before you can flash a custom rom. After downgrading the bootloader to 1.3, you can then install HSPL. Follow my guide here for complete instructions, step by step.
Click to expand...
Click to collapse
I finally got it to work! Thanks for the help. I had to find the DFT_XSPL_WP7FG3 that I had downloaded a month ago. The DFT HSPL thread didn't seem to have the file anymore.... When I found that rar, it worked perfectly; I'm now running your 7.8 rom!
I'm still unsure how the WM Device Center actually works, but I'll have to take that up with ultrashot. It seems to work intermittently, I can browse all the files on the phone with the pc that I first set it up with, but all it seems to do on my other pc is just show "error" instead of "not connected."
Its probably because I was trying to do all this on Win8x86.
thals1992 said:
I finally got it to work! Thanks for the help. I had to find the DFT_XSPL_WP7FG3 that I had downloaded a month ago. The DFT HSPL thread didn't seem to have the file anymore.... When I found that rar, it worked perfectly; I'm now running your 7.8 rom!
I'm still unsure how the WM Device Center actually works, but I'll have to take that up with ultrashot. It seems to work intermittently, I can browse all the files on the phone with the pc that I first set it up with, but all it seems to do on my other pc is just show "error" instead of "not connected."
Its probably because I was trying to do all this on Win8x86.
Click to expand...
Click to collapse
First start Zune, then WMDC will start working!
TheXev said:
First start Zune, then WMDC will start working!
Click to expand...
Click to collapse
That did the trick. Been using it for a while now. THe only issues I've had has been with GPSKit Tether. MS Streets and Trips doesn't think that the data is NMEA 2.0 compatable, I can open terminal on the port being used, and it shows data. The only thing I would like to see in your build is the updated start icons. Also I can't seem to get the Nokia Counters installed. I got the files to copy from my ringtones to \Windows, but can't seem to get the provxml file to execute.

Categories

Resources