Hello Everyone,
I have some problem with the at&t 8525.I have tried to upgrade the windows 5.0 to windows 6.0. Suddenly it got stuck on Tri-colour mode. I then tried to downgrade to windows6.0 to windows 5.0 cingular_wwe.Now the phone got stuck on at&t operator logo and its displaying following details in red colour
M 05 R 1.40.30.00
S 04 G 32.73.7020.16H
B 06 D 2.15
One of the other problem is my mobile cannot be synced to my laptop.
When I try for soft reset the tricolour mode will appear again and the at&t logo get disappeared.But when I remove the battery and connect the device again at&t logo will appear and the tricolour mode will be vanished.
I have read several posts ,but could not understand the technical language.
Even then I tried to follow some procedures I could not succeed to bring the mobile alive.
So please give me a solution in a simplified and clear format.I love my mobile very much. So please help
Related
i looked everywhere and i cant find any thread.
this xda exec O2 a customer of mine brought it, he was tryin to install adobe , now when it boots , it stucks at the o2 logo with red words
R 1.09.00
G 42.42.p8
D 1.30.107 WWE
I HARD REset it, soft reset, still not recognized by windows active sync or any rom upgrade .or bootloader upgrade software.
i followed instructions as per:
http://wiki.xda-developers.com/index.php?pagename=HTC_Universal
thnx for help
Try to put it in boot loader mode (serial), connect to the pc and try to flash it again
it wont go to the boot loader, i tried all tricks
i have orange SPV M700 pocket pc mobile. i upgrated my mobile to windows 6.1. after that i upgrated my mobile to Windows mobile version 6.1 elegand edition but upgradtion, it stuck at bootloader mode. now i can not upgrate my rom. it stuck at windows mobile 6.1 logo. when i go to hard reset it come to bootloader mode shows " Trin 100
IPL -0.50
Trin 100
SPL-1.07.0000
this is the message i m getting from last two days. i tried to make every step to lad a rom but cant upgrade my mobile. plz help me to make my mobile alive.
there have been may posts similiar to your problem ...
generally speaking the answer seems to be to flash your Rom,
and then when it gets stuck again at bootloader, just check that 'usb' appears at bottom of bootloader screen
then just run the reflash again (without switching off, or unplugging phone)
this usually does work. even if it takes you 2/3 attempts
Dear All,
Please urgent help required.
my HTC P3300 (Artemis) stuck up when i was trying to start it up. when i use to turn my cell on, i goes to the starting screen shows the following numbers and then stuck up.
IPL 3.07.0001
SPL 3.07.0000
GSM 02.69.90
OS 3.7.0.0
the screen does not move after that. i tried soft reset through the reset button but result is the same.
i also tried hard reset and when i puch the green phone button to proceed, a message come "FORMAT FAILED" and the phone stucks up.
i am quite a lot of problems since i have upgraded to WM6 from WM5 last week.
i am quite sucked with this problem. not been able to use my set since yesterday.
please also note that my HTC was not syncing with my PC since i have upgraded to WM6.
PLEASE HELP URGENTLY.
Nomi
You must upgrade :
-Remove SD-Card
-Remove Sim-Card
-USPL
-Upgrade new ROM
thank. i got through to install wm 6.1.
can any one please tell me which is the most stable ROM for 6.1 or 6.5
which one is better for my HTC artemis.
please post link to the ROMs
I'm using two roms :
Shady313-23081R1 : http://forum.xda-developers.com/showthread.php?t=546805
dheewatara-s 23075B1 : http://www.pdamobiz.com/forum/forum_posts.asp?TID=255901&PN=1
same problem..pls help
i have same rom and ratio with u nomi...but my problem still occur...
where do u get the USPL eventually?
Hi All,
I am new to this so forgive me if I do something wrong.
My XDA Exec has stopped working and I can't boot into it. I have tried a hard reset but still fails. I have tried to do "bootloader" and that doesn't work as my PC's cannot recognise the device so Active Sync can't connect. I have tried this on Windows XP and windows 7. Both fail.
The screen it sits on is the O2 logo and there is some text which says,
PU10 64MB RAM
ROM image built:
Dec 15 2007
13:00:09
R 1.15.00
G 42.51.P8
D 2.12.08 WWE
Please can someone point me in the right direction on how I can fix this.
Thank you,
resolved
Never mind, This is resolved. My XDA is up and working.
Hi friends, I have flashed my Arte110.
Now when in screen have to be windows logo is black screen and keyboard lights.
Waited for 15 min but no os is loading. What I have to do now?
Please help
tms88 said:
Hi friends, I have flashed my Arte110.
Now when in screen have to be windows logo is black screen and keyboard lights.
Waited for 15 min but no os is loading. What I have to do now?
Please help
Click to expand...
Click to collapse
before it happens what do you do on the device?
because the devices that make bricks are usually stuck on windows logo or screen 3 color...
Connected to pc an do upgrade with arte upgrade tool. Then when all proces done i done hard reset. waiting for os and pfff. now when I power on to me writing
ipl 1.13.001
spl 1.13.000
os 3.13.0.0
gsm 02.49.90
then black screenand nothing.
botloader loading okey, if connected with pc showing usb but activesync dont find
pc showing unknow pocket pc device
...
simple fix dude..
click the link in my signature for "uspl 1.11.cmon rom upgrade tips&tricks"
i see that you have flashed a rom without doing the USPL because your SPL is 1.13.0000
you need to look for the 5th post on my tips&tricks thread, BRICKED DEVICE".. you will need to click the link supplied, it will then divert you to the list of original roms, now look for the original rom that has the bootloader number 1.13.XXXX. download and flash it to your device.
done
Rn
(XXXX=any numbers)