Database Users

GMS ERROR, Help Me

My 02 XDA is error.
Soft reset xda not start, it stuck o2 image and blink.
Hard reset on screen display:
WALLABY
Bootloader
V5.15
GMS ERROR
and stuck.
I want re upgrade radio stack but I don't know how to connect XDA with PC. Put in XDA to cradle but PC not connect to XDA. How to PC can connect XDA to upgrade radio or firmware for ROM???
Help me please.
Thank.

I have the same problem but nobody khow what to do

See here:
http://forum.xda-developers.com/viewtopic.php?t=11534

My SVP M600 phone got stuck at Starting screen

Hi Friends,
My new mobile phone SPV M600 got stuck whil starting showing four lines of messages as shown below.
IPL 2.10.0001
SPL 2.10.0001
GSM 02.07.20
OS 2.10.1.22
Can any one please help me in geting my phone to today's screen.
I also attached the screen shot for reference.

did you try a hard reset ?

Ya I tried both hard as well as soft reset but same screen is stuck again and agian.Can any one please help me in this regard as I am very new to PDA family.

Ok, first things first:
Since you are new to this, are you sure you preformed a hard reset?
It is done by holding power + camera + comm manager buttons (one on the right, two on the left) and pressing with stylus in the reset hole at the same time.
A message should appear asking you to press 'send' (green phone button) to confirm reset.
If this does not help, you may have a serious problem.
Please answer the following:
Is the device fully charged?
Phone will fail to boot if the battery is too low.
Did you install any software right before this happened?
This should have been resolved by hard reset, but just in case I am asking.
Did you change the ROM, attempted CID / SIM unlock?
This could require more serious measures than I can advise on.

I did exactly the same thing which you mentioned.But even then it is stuck at the same screen.
Ya u r right I unlocked my mobile using a software from eBay.The unlock was successfull and I tried to insert T-Mobile sim, it also captured the signal and I was able to make and recieve calls then after that I wantedly switched off the phone and then tried to start it, there got the problem.

Can any one help me in this regard please.

I am having the same problem, but my phone is not sim-locked.

I've got the same problem after attempting smart1_wm6_pp8mb.exe
I'm having the same problem with my G4 QTEK S200:
Attempted to upgrade to WM6 Rom using smart1_wm6_pp8mb.exe
After reboot the phone got stuck at the QTEK Screen
Tried Hard Reset (Camera+Power+Comm+Reset) followed the steps with the same results (bricked)
I also tried re-flashing the rom back to the factory one using RUU_Prophet_220734_2207114_024721_QtekWWE_Ship and ROMUpdateUtility-NoVendorID.exe in Windows Vista with WMDC (Windows Mobile Device Center v. 6.0.6873) and the phone in boot loader mode (tri color screen) with working USB cable, with windows firewall disabled and symantec AV disabled as well, RUU keeps saying error 260 "the update utilitiy cannot connect to your pda phone..." .
Do you think I should try this process using XP instead? No matter what i try i keep getting the error 260
Any help would be greatly appreciated

Got it fixed!
it was definately a Vista issue. once i tried it in XP with ActiveSync it worked like a charm and i got my phone back up and running. also used spb backup and restored all my settings.

ipl/spl screen
i got the same problem with new rom wm6, and the 260 eror, my problem is that i have xp and the activesync does`t connect ...
... means i cant redo the original rom ????
PLEAAASEEE HELPPPP !!

Again My phone SPV M600 got stuck at IPL/SPL screen
Please Can some one advice me how to get my phone back.
I raised the same issue 7 months back after that my phone got recovered automatically and there were no issues till last month. Last month onwards it is again got the same problem and now it is permenantly stuck at that screen what ever you do.

yekanth said:
Please Can some one advice me how to get my phone back.
I raised the same issue 7 months back after that my phone got recovered automatically and there were no issues till last month. Last month onwards it is again got the same problem and now it is permenantly stuck at that screen what ever you do.
Click to expand...
Click to collapse
A rom reinstall on xp solved my problems on that one. retry a couple of times! It may not work the first time! hard reset as well...
Try an official wm5 rom just in case
good luck

Can you please gimme step by step procedure
HI Phil,
I am new to these kind of installations . CAn you please Gimme step by step procedure for ROM installation.

mine is now also stuck, after trying to install new rom. wont connect to active sync either, have i fooked it? tried hard reset etc.
thanks

(with a turned off phone, press and hold camera button then insert USB cable)
then flash provider ROM
RECOVERING FROM ERROR IN STEP 8 WM5->WM6
1. Don't panic
2. Don't panic
3. Unplug the phone
4. Reset with stylus,and keep the Camera Button pressed.
5. A 3 color screen will appear(Bootloader Screen)
6. Connect your device with your PC,and run the NVID(no vendor) WM5 rom.
7. The device will be resetted after RUU(rom update utility)finishes
8. Repeat the WM6 upgrade,from STEP 5..
Click to expand...
Click to collapse
from here http://forum.xda-developers.com/showthread.php?t=310452

hi jay
i seen your post in n00b guys one, i fixed it!!!!, thank you so much, i couldnt remember how to get it to those 3 colours.
thanks again
Colin

Hi Iam unable to get the NVID ROM
Hi,
I am unable to get the NVID ROM. The Rapidshare link that has been provided in the other thread is not working. Can some one tell where can i get the ROM.

collywog19 said:
i seen your post ...
Click to expand...
Click to collapse
no problem mate.
..and yekanth i see what u mean about the dead links. i have the files on my computer at home but i'm posting from my prophet right now, so i can't upload. Try using the "pdaviet temp" from one of the wm6 threads?
(http://rapidshare.com/files/54265407/Prophet_PV_Temp.zip)

Hi Iam able to update the Rom but no use
Hi,
To mention my phone is from orange-UK. I got the orange rom from our FTP site and did the flashing/update what ever you say.But still it is getting stuck at the same IPL/SPL screen. Iam very much worried that I will not get a proper solution for my problem.It will be very grate full if some one resolve my problem.

just seems strange...how did you fix it last time? did it just start working again? A random guess would be that the camera button got liquid spilled on it or is stuck in.
If the camera button is pressed in the phone will go to 3 colour screen every time it is turned on.
It won't do any harm if you try to press/move that button to see if u can "unstick" it, not likely I think but u never know...

XDA EXEC STUCK AT O2 logo

i looked everywhere and i cant find any thread.
this xda exec O2 a customer of mine brought it, he was tryin to install adobe , now when it boots , it stucks at the o2 logo with red words
R 1.09.00
G 42.42.p8
D 1.30.107 WWE
I HARD REset it, soft reset, still not recognized by windows active sync or any rom upgrade .or bootloader upgrade software.
i followed instructions as per:
http://wiki.xda-developers.com/index.php?pagename=HTC_Universal
thnx for help

Try to put it in boot loader mode (serial), connect to the pc and try to flash it again

it wont go to the boot loader, i tried all tricks

XDA11i Serial V1.01

Hi all, Hopefully some wise person can assist me.
I downloaded a ROM update for my XDA11i from this site :Alpine_Ext-1.11.162_Radio-1.04_O2stuffstripped_Camera_Fixed which was highlighted for a Alpine. However on running the update you get a picture of a MDA and a message "The ROM upgrade utility does not design for your device. Please get proper ROM upgrade utility and try again"
Unfortunatly my XDA11i is now stuck on a blank screen with Serial V1.01 and is not recognised by activsync or My computer. However in the cradle the screen shows USB V1.01
I have tried installing the official O2 ROM update: AP_O2UK_11100_169_10000_ShipXdaIIi but get the following message Error 101: connection error. I assume because my XDA is not recognised by Activsync.
I have spent days trawling the forum and trying the various solutions to no avail. Most of the links are dead as in archive.
1. On reset and hard reset the serial text only dims.
2. I tried the process posted by CelticLo and copied a ROM image to a SD card, however again on hard reset the sserial text only dims.
Any assistance would be very much appreciated.

Have you tried updating to the latest version of Active Sync on XP
or following the guide for Vista

Take off battery. wait for about 10 hrs. put back battery and switch on the power.

Thanks for the tip's
I have tried Activesync on XP and Vista still does not work.
I have removed the battery for two days and recharged it through the cradle, on returning the battery and switching on. It returned to the serial screen.
I tried flashing with the following rom : [Maxishare_net]alpine-1.11.171-radio-1.04-bluetooth-patched-camera-fixed again i get the message it is the wrong ROM??
I can not understand why I keep getting the wrong ROM message as it is definetly a XDA IIi PH10C
thanks anyway

Furkinl said:
I have tried Activesync on XP and Vista still does not work.
I have removed the battery for two days and recharged it through the cradle, on returning the battery and switching on. It returned to the serial screen.
I tried flashing with the following rom : [Maxishare_net]alpine-1.11.171-radio-1.04-bluetooth-patched-camera-fixed again i get the message it is the wrong ROM??
I can not understand why I keep getting the wrong ROM message as it is definetly a XDA IIi PH10C
thanks anyway
Click to expand...
Click to collapse
erm u are trying to flash on a pc running vista?? thats your problem, u cannot flash on a vista pc, xp home/pro ONLY!

Thanks for the advice, tried on XP and it worked fine, it would seem that activsync was not required in this case. At least my XDA is ALIVE for now.
many thanks

You simply could revive it again by Resetting it via the stylus

thnx 4 all the soloutionsss
i had same problem , but once i tried it on xp, its works for me, my ppc now is refresh installed,
thnxx

qtek 2020i
for information the french rom is available on this place http://www.planete-htc.com/index.php?mod=download choose dangaard section there is two files to download
1. choose 2020i dangaard rom
you can not use it
2 download the radio file
it contains an exe called upgradeut make it in the directory of your dangaard folder and you will be able to flash it
it work also for pda stuck in serial usb
voila

qtek 2020i
radio file 1.04 two mega

do a hardware resett and it should be the phone back to defaults

XDA IIi V 1.01 Serial /USB
Hello,
I tried to update my XDA IIi from a new rom version found at o2.ie website but my XDA IIi is stuck and showing Serial on top and v 1.01 at botom. When i attach it with cardle it shows USB instead of serial.
I have tried Almost everything that i found on this forum in last three days.
Hard reset / soft reset/ new installation using different version etc.. but nothing worked for me..
Now I am really confused and can't find what to do.. Can any one from XDA gurus/ developer help me and sumarize what should i do?
Thanks in Advance
Zeeshan

Yes, i have the same problem i did exactly what was done above me pls can someone help!!!!!!!!!

Furkinl said:
Hi all, Hopefully some wise person can assist me.
I downloaded a ROM update for my XDA11i from this site :Alpine_Ext-1.11.162_Radio-1.04_O2stuffstripped_Camera_Fixed which was highlighted for a Alpine. However on running the update you get a picture of a MDA and a message "The ROM upgrade utility does not design for your device. Please get proper ROM upgrade utility and try again"
Unfortunatly my XDA11i is now stuck on a blank screen with Serial V1.01 and is not recognised by activsync or My computer. However in the cradle the screen shows USB V1.01
I have tried installing the official O2 ROM update: AP_O2UK_11100_169_10000_ShipXdaIIi but get the following message Error 101: connection error. I assume because my XDA is not recognised by Activsync.
I have spent days trawling the forum and trying the various solutions to no avail. Most of the links are dead as in archive.
1. On reset and hard reset the serial text only dims.
2. I tried the process posted by CelticLo and copied a ROM image to a SD card, however again on hard reset the sserial text only dims.
Any assistance would be very much appreciated.
Click to expand...
Click to collapse
Where can I download this rom?
Alpine_Ext-1.11.162_Radio-1.04_O2stuffstripped_Camera_Fixed
Thanks in advance
Chet

look and lern
put qtek 2020i in stativ (conect to pc via usb)and push power ( on screen will apear USB and v1.01), and you dezarhive :astel_wwe_11100_112_10200_ship, and doble klik on AlUpgradeUt and bios at ppc wil be update !!!!! This is all, the ppc will be now reinstaling, be patient and wait until will be reinstaled (25 min)

Problem after downgrading from wm6.5 back to wm5

I face a strange problem on my dopod 818pro after I donwgrade from wm6.5 back to wm5 NVID rom.It take about 5 minuets to boot back to the windows,even thought i did several time of hard reset it is d same too. Does anyone encounter with this kind of problem before? Please advice.

No sifus can HELP???

Finally I solved d problem liao by upgrading back to wm6.5 Build 23053 WWE bikertibi edition.

Help <urgently needed
Hi everyone,
I tried to upgrade my HTC universal from WM 5 to WM 6.5 using the rom provided by xda v1.01 (128MB rom).
I tried to install the upgrade from my laptop but during the process i noticed a sound indicating that the USB connection was lost. Now all i can see in my phone is 'Serial' at the top and 'v1.01' at the top. Aside that, the phone's literally DEAD.
Is there anything I can do about the phone or is it wasted?
Would appreciate any form of response.
Thanks.