i hard reseted my pocket pc once again.
The 1st message i receive after the hard reset is done and b4 displaying the today screen an eror is displayed where VoiceCmd.exe is the one diplaying that error.And 2 b more specific the message displayed is:" Cannot open"voiceCmd".A critical component is either missing or cannot start because program memory is unavailable.Tap start then .....
Once i get rid of this notification, a new 1 appears displaying Error OneNote.cab and then the same message is displayed.Then after removing this error the hard reset continues diplaying the message"Setting are being applied and windows will restart automatically.The windows restart then and as usual after the rebooting the same VoiceCmd.exe error is diplayed and cannot type on the screen cz it is not alligned.After the hard reset the op is not asking me to allign the screen anymore.So i have to go to settings and allign it manually.
Then after trying to install any.cab program will display this message:"Name of the program.cab".A critical component is either missing or cannot start because program memory is unavailable.
And of course when i plug the usb the lovely message flashes on my ppc screen displaying" Cannot execute repllog.exe"
Cannot run memmaid neither sktools.
Hellllllllppppppppppppp!!!
what rom are you using, and what extended rom?
Psi
N A J said:
i hard reseted my pocket pc once again.
The 1st message i receive after the hard reset is done and b4 displaying the today screen an eror is displayed where VoiceCmd.exe is the one diplaying that error.And 2 b more specific the message displayed is:" Cannot open"voiceCmd".A critical component is either missing or cannot start because program memory is unavailable.Tap start then .....
Once i get rid of this notification, a new 1 appears displaying Error OneNote.cab and then the same message is displayed.Then after removing this error the hard reset continues diplaying the message"Setting are being applied and windows will restart automatically.The windows restart then and as usual after the rebooting the same VoiceCmd.exe error is diplayed and cannot type on the screen cz it is not alligned.After the hard reset the op is not asking me to allign the screen anymore.So i have to go to settings and allign it manually.
Then after trying to install any.cab program will display this message:"Name of the program.cab".A critical component is either missing or cannot start because program memory is unavailable.
And of course when i plug the usb the lovely message flashes on my ppc screen displaying" Cannot execute repllog.exe"
Cannot run memmaid neither sktools.
Hellllllllppppppppppppp!!!
Click to expand...
Click to collapse
Hi Did you manage to fix this? I am getting this and cannot even switch off my handset
I'm having same problem, has anyone found a solution?
Related
Tried to install PPC2003PE.nb1 but now can't use o2 at all!
What I did:
- call wallaby (v5.15) ->flash tools->CE+BOOT TO SD (ok)
- start XDArit.exe->READ FROM SD->test.nb0,testnb1
- start XDArit.exe->WRITE TO SD, PPC2003PE.nb1
Message:
XDArit: Failed to open device \\.\PhysicaDrive2
(I use WindowsXP.XDArit can't find SD?)
Next - I made mistake
- start RUUv1.09_CEv4.00.05wwe_O2_Ozone.exe when o2 was connected to PC (don't know why I started it...)
- during installation it stopped on 77%
Now:
-when wallarby starts GSM after WAIT message->GSM ERROR
-o2 starts very slowly and stop with blank screen only with keyboard and blue bacground in the top.
Can anybody help me?
You're experiencing a bug we'll be looking into once we have some time. You should try the old XDArit to write your card. Given that your bootloader still works, you should be fine after you burn your old ROM back into your device, although I'm not sure what the 'GSM ERROR' is all about.
Thanx! Old XDArit.exe works good.
But after restore nothing changed in o2.
Still message GSM ERROR in wallarby and blank screen after reset. Probably Radio Unit corrupt.
Installed PPC2003PE.nb1.The batary is totally discharged,GSM doesn't work, after reset system starts~15min,no signal about charging.
How to charge o2-maybe it is the only problem?
Finish!Installed RUUv1.09_CEv4.00.05wwe_O2_Ozone.exe which can start without power control.Works fine!
Can you share RUUv1.09_CEv4.00.05wwe_O2_Ozone.exe with us?
ruuv1.09.... is the same as rsu-v4.21
nice that they keep changing how files are named.
http://www.sourceo2.com/NR/rdonlyres/e6cnrtrwu7je7z4igecipun72rzqqbftxrz5dch75i64qjawvtwmmvt64qqrxanxkdcwcapvo5aupj4wt6hc52vtlhe/RUUv1.09_CEv4.00.05wwe_O2_Ozone.exe
I have installed the IIWPO (theft protection) program manually (not in ROM) for testing purposes. After uninstall an error message appeared periodicaly. The error txt is "Cannot execute \windows\IIWPO_main.exe". Also I can not find any reference to this file in the registry (maybe faulty registry editor, PHM ?) or in the startup folder. Also tried searching in the file contents on entire device. No success. Please, help, this error message is pissing me off
Hey guys.......thanks ahead of time.....
I tried uninstalling IIWPO(theft protection).........and now I'm getting this error periodically(almost randomly...but very often)...
"Cannot execute \windows\IIWPO_main.exe"
I tried removing everything I knew of.........but I obviously didn't succeed.......any help?
It's hidden as an event.
Use this to remove the hidden entry for IIWPO_main.
In you un-install IIWPO you will definitely miss out one thing: The event that makes it run after turning your device on.
There are 2 ways to remove the event:
- Use the Scarybear software
- Hard-reset
Note that after using the scarybears software, you have to do a soft reset, but NOT by pushing the reset button with the stylus. Instead, hold down the power button, say yes at the dialog box. After it's off, bring it back up by holding down the power button again.
Some time ago I downloaded and installed the Lockscreen application. This was before I truly understood how to lock the buttons !!
Tried to remove it and have been unsuccessful...
Every so often I now get the error:
Notification Error
Cannot execute windows\LockScreenWD.exe
I have to clear this 5 times in succesion and the system goes back to normal operation until it happens again.
I've tried a registry editor to clear out any entries but cant get rid... anyone got any ideas...
Hi all,
something strange happened to my XDA (O2 ROM v2.21.4.101):
* my "remove programs" list is now completelly empty, even if I have many programs installed and running!
* I can no longer install any new program ("exe" or "cab") - installation starts, but always ends with unsuccessful message
* active sync 4.2 no longer connects!!
Apart from this, everything seems to be in order.
Any help/hints would be mostly appreciated, trying to avoid an always painfull "hard reset"...
Thanks!
Hm, have you tried updating your ROM? That would reset your phone and update it so it should work...
But you would loose your contacts etc as you cant sync now? Hmmm
keyser said:
Hi all,
something strange happened to my XDA (O2 ROM v2.21.4.101):
* my "remove programs" list is now completelly empty, even if I have many programs installed and running!
* I can no longer install any new program ("exe" or "cab") - installation starts, but always ends with unsuccessful message
* active sync 4.2 no longer connects!!
Apart from this, everything seems to be in order.
Any help/hints would be mostly appreciated, trying to avoid an always painfull "hard reset"...
Thanks!
Click to expand...
Click to collapse
modify the registration:
HKLM\ControlPanel\AdminPassword\Group=0x1(1)
delete the key "Redirect"
Than soft restart. You'll find a "Policy" or "Stratagy" icon in the "System" page of the "Setting" window. Clear the checkbox of restriction.
Thanks for the info - unfortunatelly, I already did an hard reset to the PDA. I will keep it for future reference, though
biolover said:
modify the registration:
HKLM\ControlPanel\AdminPassword\Group=0x1(1)
delete the key "Redirect"
Than soft restart. You'll find a "Policy" or "Stratagy" icon in the "System" page of the "Setting" window. Clear the checkbox of restriction.
Click to expand...
Click to collapse
just for the record that check box was already clear when I looked at it and it didn't do anything for me
Had to do a restore from a back up a couple weeks ago. damn it.
Mine did it after a corrupt install. SOB.
The values basically haven't changed the behavior...
Hi all,
I have copied the values exactly as they were, but still nothing happens...furthermore my ActiveSync on the MDA Vario seems not to recognise any connections, even when the phone is connected with the ActiveSync of the PC. Is there any way maybe to reinstall only the phone portion on ActiveSync in the MDA? I downloaded a file "activesync.exe" from the ftp server. is it the pocketpc portion of activesync?
Thx a lot
Hi all,
When i used my device this morning i could not start messenger or any other program. The device is also unable to connect with active sync. I haven't got anything installed over the last days.
It just happend. Windows is extremly slow, i don't have contacts anymore, no pim's or anything. The phone did remeber my last calls and such. My email accounts are also missing.
I have done some soft resets and now the device is stuck on the windows mobile splash screen (the green screen with windows logo and name).
I don't know what to do How can i get my device to work again?
Edit
The device has started after 20min at windows screen. Touchflo 2D has not loaded and i can not make calls. I can't start any program, it gives an error that the program can not be started because it has not been signed with a certificate or some component is missing.
Thx in advance for reading.
If you have an SD card inserted I would try removing it and see if that improves things!
I had a similar problem with an Xda Zest which turned out to be a corrupt SD card. Once it was formatted again everything was bach to normal.
I removed the SDcard, tried another one (also 4GB), then used the old one again (formatted) .
But no luck.
I will try again removing some software if the device allows it. Will update.
dont put any SD card in the device
and try
Start/configuration/sistem/Erase memory
and there just put 1234 and press yes
This metod erases everithing from your device leaving it just how it came from the factory
You may also perform a hard reset as you have mentioned to receive a message "some component is missing". Hard reset should fix any software (or Operating system) issues with your phone.
WARNING: Hard reset will erase all your data and the customizations you have made to the phone.
Refer to the following for instructions on how to hard reset:
http://forum.xda-developers.com/showthread.php?t=453324
I have done a hard reset without the SD & sim card. It solved all the problems. I was able to recover my contacts with ActiveSync.
Thx all for helping