Hermes up close questions - 8525, TyTN, MDA Vario II, JasJam General

I'm new to my hermes( htc tytn )
I have a few questions
1. when your battery goes down, how does it go down? e.g in 1% at a time or about an hour later or so you'll see it jump down by 10%. in other words 10% at a time
2. how does the keyboard auto backlight sensor work? where is this sensor also?
and lastly
3. how long is a battery suppose to last using wifi?
Many Thanks,
Mr_GTI

Battery drain is only reported in 10% chunks unfortunately
Keyboard Backlight Sensor is on the keyboard just below the green phone key ( or above letter p if you prefer) Allows you to set keyboard light to come on only when darkness decends. However as it's pretty I have mine set to always on.
Mmmm. Never had it on constantly until battery goes flat. But I use it for maybe 1 to 2 hours a day and battery lasts between 1 and 2 days. Generally I charge daily.
Mike

thanks for that Mike.
is my keyboard sensor maybe faulty? it doesn't go on if I cover the sensor with my finger it doesn't go on. or at night.. I remember being outside also and it did not go on. it just went on the once I remember, but have not seen again. is there a specific way it works or functions?
I remember you mentioned somewhere in the forum's, I can't get to it right now, but you said that htc wil be having the tytn's wm6 rom update in the support section in june. is that yet to be launched on their site this month stil?

Mr_GTI said:
thanks for that Mike.
is my keyboard sensor maybe faulty? it doesn't go on if I cover the sensor with my finger it doesn't go on. or at night.. I remember being outside also and it did not go on. it just went on the once I remember, but have not seen again. is there a specific way it works or functions?
I remember you mentioned somewhere in the forum's, I can't get to it right now, but you said that htc wil be having the tytn's wm6 rom update in the support section in june. is that yet to be launched on their site this month stil?
Click to expand...
Click to collapse
Hi
Start/settings/buttons/backlight and tick the sensor box. (if it is ticked you can try unticking and coming out and then go back in and re-tick.)
If you go to the google search sticky post - near the bottom are HTC links to check from time to time for updates. The official WM6 for Hermes is now scheduled for July I believe.
Cheers
Mike

thanks mike, it working now
I just want to clearify something. When my display backlight is on dim, dim to the very end, the bar pulled over completely toward the left hand side, when ever I apply screen taps or pressing of buttons, a dim light flickers on the accept call button, is this with all the hermes? or is it mine that's just like that, some kind of fault?

Mr_GTI said:
thanks mike, it working now
I just want to clearify something. When my display backlight is on dim, dim to the very end, the bar pulled over completely toward the left hand side, when ever I apply screen taps or pressing of buttons, a dim light flickers on the accept call button, is this with all the hermes? or is it mine that's just like that, some kind of fault?
Click to expand...
Click to collapse
I think I saw someone-else say that. Mine doesn't do it. However, I get a dim glow from the camera flash from time to time that I have not seen anyone report. These little quirks, possibly caused by leakage currents are not really a problem unless it causes excessive battery drain. It might be cured by a hard reset (providing you have a full back up - lest you face re-installing everything).
Mike

Related

Screen glitches/freezes (To do with magnetic case)

Hello from down-under ,
I've come to put forward a problem myself and a few others are having over at the Mtekk forums. I currently just purchased an I-Mate JasJam on Telstras' new NextG network and have been using it for about a week and a half. As this fantastic piece of equipment is a little on the expensive side, I wanted to make sure it was kept safe all the time, so I began to use (no matter how silly it made me look ) the I-Mate supplied Pouch, little did I know it did more damage then not using it...
After investigating over the last few days, It was concluded that the magnetic found in the supplied Pouch had some diverse effect on the switching on Landscape to Portrait mode when removing the JasJam from the Pouch to answer/make a call, play a game or send a text message; often resulting in a 'bugged' or 'glitched' screen, stuck between either Landscape or Portrait etc (I fixed by removing the JasJam and sliding out the Keyboard and back in).
After I few days I thought that this couldn't be right for a brand new machine and took my problem to the Internet in which I found others with the same problem. Since then I have stopped using the supplied Pouch and am now looking at purchasing the Krussel Orbit Pouch as a magnetic-less replacement (any users with one, I'd love your feedback). I am making this thread to see if any users of the XDA-Developers board have faced this issue and ask one further question:
1. Since I stopped using the Pouch I can only find one annoying trait left, whenever I switch the Screen back on from 'Standby' mode I seem to receive a small 'glitch' in the Today Screen if the device has been locked, if the device has been left unlocked the Screen can be switched on/off with no issue - does anyone else have this problem, I'm concerned that the magnetic pouch has caused some internal damage...
Thanks,
Elite_Gamer04
Hi, there is a bit more about this problem in the accessories thread, I noticed the magnet causing issues and wondered about internal damage as you did, even possibly causing the align issues, but a few people reported back they had been using the case from day 1 and while it affected the landscape/portrait, they had no align issues or any other problems, so I don't suspect that there is any internal damage occurring..I do wonder about your screen glitch but without actually seein it..I haven't a clue, also do you have a lot of today plugins?..could possibly be one of them is buggy..I'm not sure, but the case does certainly suck, I was immediately concerned with the magnet strength, off topic..but on my device if my thumb is a bit damp or any metal touches the aluminum bezel around the ear piece of the phone..the screen will flicker.
Thanks for your reply Chaotic, My device is in the same state as when it come out of the box, so this isn't a 3rd party issue. I have tried removing/adding the default Today Screen icons to see if it makes an issue to the 'glitching' of my screen when it on/off and it makes no difference, only thing I can see that makes it not happen *sometimes* is when the device is not locked.
Well thats one user without my issue, hoping someone will report it, or I'm going to get a replacement.
*If your testing to see if you have the same issue as me, simply hold your device in your hand (try both with it Locked and Unlocked) and push the top right-hand side button which should switch your screen off, press it again for it to come on. If you see a sort of 'glitch' of white on your Today Screen and then it fixes itself (I'm talkin 1-2 seconds) you have the same as me.*
Hi chaps,
I've used the magnetic pouch from day one with my UK T-Mobile Vario II and am still yet to see the landscape/portrait switching issue when removing the Vario II to answer a call.
I had a theory about this, and it's probably going to get shot down in flames for it's obviousness, but I'll mention it anyway... Could the problem be down to the machine being powered down (manually or automatically) while in Landscape mode... then when switching on automatically when a phone call is received, the phone tries to switch back to portrait mode but gets stuck?
I have road tested this theory on my own Vario II and have not seen the problem at all, but my ROM may handle things differently to yours? Apologies again if this suggestion is obvious.
elite_gamer04 said:
Thanks for your reply Chaotic, My device is in the same state as when it come out of the box, so this isn't a 3rd party issue. I have tried removing/adding the default Today Screen icons to see if it makes an issue to the 'glitching' of my screen when it on/off and it makes no difference, only thing I can see that makes it not happen *sometimes* is when the device is not locked.
Well thats one user without my issue, hoping someone will report it, or I'm going to get a replacement.
*If your testing to see if you have the same issue as me, simply hold your device in your hand (try both with it Locked and Unlocked) and push the top right-hand side button which should switch your screen off, press it again for it to come on. If you see a sort of 'glitch' of white on your Today Screen and then it fixes itself (I'm talkin 1-2 seconds) you have the same as me.*
Click to expand...
Click to collapse
I assume you are referring to the lock/unlock option found on the Today screen? I also see a short white screen delay when using this Today screen option.
I also see an even longer delay when using the password/pin lock option. Probably something to do with the locking program checking to see if the preset time delay for locking and requesting the password/pin has passed.
Disabling both options makes starting up a lot faster, although you may of course need these options enabled. I'm sure it's something that will be resolved by the manufacturer in time.
elite_gamer04, I hadn't ever used the lock on my device, so I enabled it just to test, and there wasn't any differences, I also wasn't sure of what the actual glitch was, but since you mentioned it I did some further investigating, I do notice a white screen when coming back from standby, but it lasts no longer than half a second..definitely not 2 seconds.
g00nerz, its all good, all info around here is appreciated, but there is definitely an issue with the case magnet, I don't have a single landscape/portrait issue unless I put it in the bundle case..I use a modded aluminum case at the moment..but if I switch back it happens, I'm pretty sure the words "bundle case" are in the title of the post with others with this issue if you want to check it out.
I have read where some people were discussing that they thought some had different screens..that could be why you haven't had this issue or maybe it is ROM related, but from what I understand its been a variety of brands with this issue...now that I think about it..I wonder if all the brands bundle cases are the same?
I think its Mike(I hope I got that right) that has tore one of these apart..few posts about it with pics on the forum he might know, but anyhow I wonder if theres actually a hardware switch that triggers the switch from portrait/landscape when the slide out kb is opened, and the magnet is affecting that..could also be it was revised on some models.
I'm just speculating/guessin on what might be causing it, I really haven't any solid info other than some people definitely have an issue with the case, including me.
I also see a short white screen delay when using this Today screen option
Click to expand...
Click to collapse
I <3 you hehe. Thank god its not just me . Yes I was referring to the 'Device Lock' and 'Device Unlock' function on the Today Screen. When it is Unlocked and I switch on/off the screen I see no 'lag' or 'white glitch' but with it on I see a small 1-2 sec lag. Anyways as you have confirmed it also I don't have to worry about returning mine and will get on with my new Krussel case I'm about to order.
Thanks
P.S If others are having this issue, or know of how to fix, don't hesitate to post.
Please consider that the use of wifi may drasticely slow down the device's power up. I do use the default case with the strong magnet, and when I power up my device with the wifi enabled it takes a while until he completely awake; the wifi plus the switch landscape => portrait (thanks HTC case) slow it down.
I am also experiencing the "auto answer" issue; from time to time when I put my device off its case it answer to the incoming phone call, but till now I was not sure that the case could be involved; are you sure about this? I tried to give some testing but I was not able to reproduce it; it only happen when it is not expected to happen
elite_gamer04 said:
Hello from down-under ,
As this fantastic piece of equipment ......the I-Mate supplied Pouch, little did I know it did more damage then not using it.........I switch the Screen back on from 'Standby' mode I seem to receive a small 'glitch' in the Today Screen if the device has been locked, ....
Click to expand...
Click to collapse
Hi elite_gamer04, As you had rightly mentioned this is really a fantastic device and no doubt about it.....like you I had the same problem when I bought it around 2 months back.
I was breaking my head as to why its happening, it looked for me as if the device hangs on and off...but did not notice keenly the instances when it happened as removing it out of the pouch was too normal a thing that did not hint me that it has something to do with the issue...But I was totally broken and disturbed and decided somehow I am going to get a replacement. I took it to the service centre and the guy there (very smart) as soon as I mentioned about the problem ( I went there thinking that it has something to do with the sliding mechanism) responded spontaneously taking the pouch opened the flap and took the magnet side over the screen and showed it to me....wow yes...its the pouch which was the culprit as we noticed the screen going crazy....Anyway I was relaxed but from that instance I kept aside the pouch that came with the pack and I am currently using a different one from the stores. Till now I have noticed no glitches and am happy I own a real amazing fast device.
About the other glitch you mentioned when the phone is locked yes I tried and it is there even for me but I dont think its a major issue for you to replace the device as its something to do with the screen refresh rate and memory which am sure would be fixed by new ROM upgrades in the days to come...but relax rest assured you own a fantastic device.
All the best
Thanks for posting this about the screen - I thought I was going nuts. I bought a replacement pouch that has a belt loop - so slightly more secure than the clip. But when i started using it - it always switches to landscape mode.
I'll have to find one without a magnet i guess!

Video of Hermes problems... please watch and let me know your opinion?

Hey all,
I've read these forums, and am 90% sure I have a defective Hermes. However, I'm unsure, as these forum posts were just text, and therefore can't really accurately describe the problems being seen. So, I made a YouTube video showing a couple of my issues, especially the screen fading to white. Like I say, I'd just like confirmation, and I'd like this post and video to serve as a help to others who are wondering if they have the same problem. You know what they say, a picture is worth a 1000 words .
Here are more details of my problems, in no particular order:
o The buttons reset after a quick power off and on (not a reset).
o The screen fade problem resets itself after a quick power off and on (not a reset).
o The screen calibration issue (not shown in video) seems to last a little longer sometimes. The issue is that calibration gets a little off. It seems to be by 10-20 pixels, but I can't repeat this as readily as the screen fade.
o This has happened with and without a memory card inserted.
o I've tried two different batteries, with the same results.
o I've tried three different firmwares (original, WM5 update, WM6 Black 2.0).
o The battery quick powerdown issue has only happened to me once (battery drains 10% every minute).
Here's the link to the video. It's only 84 seconds, so take a peek!
http://www.youtube.com/watch?v=zQWqTkoMX_4
Let me (and others) know your thoughts. It'd be appreciated.
PS... about the screen calibration...
FYI, I know about the screen calibration issues some have had wth the Hermes. However, I don't think this is that problem, since I never, ever have to recalibrate my phone. It always corrects itself eventually.
The screen calibration issue (not shown in video) seems to last a little longer sometimes. The issue is that calibration gets a little off. It seems to be by 10-20 pixels, but I can't repeat this as readily as the screen fade.
Click to expand...
Click to collapse
This has been documented HEAVILY in the wiki and the forums so I wont answer that.
The rest seems VERY weird indeed especially the screen going white?!?!
Is it still in warranty because I would so send it to be repaired.
Not seen anything like that on any forum. Are you keeping it somewhere hot or near an e.m. field just before use?
What additional apps have you installed? Do these problems still occur with an "empty" phone (i.e. right after a hard reset before installing third party apps)? If so then that should rule out software and firmware (ROM).
Fade to white issue: hardware problem IMO
Buttons stop working issue: looks like software IMO
Sleuth255 said:
Fade to white issue: hardware problem IMO
Buttons stop working issue: looks like software IMO
Click to expand...
Click to collapse
I agree, the screen going white is similar to when I had my O2 XDA EXEC (HTC Universal) in which whenever I moved the lcd into the mini laptop mode the screen would fade to pure white. When I sent it into PPC Tech they notified me saying in which the lcd cable was damaged itself. Im not sure if thats the case with you necesarily, since it seems the screen goes back to normal after powering the device to standby and back.
The keys are most likely software/rom issues. Perhaps maybe you should reflash to a recent rom and see what happens. Although if that doesnt work I suggest you send in for replacement or warranty. I neeever in the 6 months I had my phone did I ever have problems like the one you've listed.
::EDIT::
I just realized I saw that you tried multiple roms, if thats the case I realllly believe you have a defective phone. It does happen that one in a hundred tend to go bad..
Had similar occurance when mine had gotten damp.
fading screen and hardware buttons
Hi,
I've reported some time ago these issues, they started with LVSW Edition (2007-03-20) and after that Pro - BLACK 2.0, 2.5, 3.0 and still with 3.01.
I don't think is hardware related. i happens in random way. No specific apps or time or connection.
I've had similar issues with the buttons not working on my 8525. It seems to have to do with changing in and out of landscape mode. For example, I'll always have problems if I reset the phone and leave it in landscape mode and I always have to push the keyboard in and pull it back out to get everything working right.
If the buttons DO work, they are usually wrong, like up and down will instead move left to right. Again, pushing in and pulling out the keyboard fixes it for me. I recently upgraded to a new ROM and couldn't say if the problem persists or not.
As for the white screen issue - I'd say it's FUBAR'd.

Touch HD/Blackstone Backlight Auto Adjust Problem

Firstly let me say this:...... I have a phone that has had to go back once because of a weird problem - so it might be "one of those phones " (the prob WAS fixed by a new board from HTC but thats another story !)
Here's the prob. Today when I was typing a text the back light kept adjusting up and down. This has NOT happened before So I did some tests:
1) Its to do with the autoadjust feature (not a prob when its OFF)
2) All is OK UNTIL you start to type this is how I spotted it typing a text. The backlight was going up and down - I thought my eyes were going!!!
ATTEMPTED RESOLUTION:
Fristly I did a soft reset......(prob still the same)
I down loaded LUMOS, which shows actual numbers for the light sensor,
Here's what I found......
It moves up and down a bit then settles, in a dark area its on say 3 or 0 but when I type on the screen it goes up and down like a yoyo ! ie 3,79,120,3,0 if I stop typing it settles on 3 or 0. AND THAT IN A NUT SHELL IS I "THINK" THE PROB !
"The light sensor seems to be affected by typing."
I never noticed this before so this may be a fault.
LUMOS seems to cope slightly better than win software with this and I can get around this by turning the sensor off, but if its faulty BACK it GOES....(AGAIN)
The last prob did my head in. I love this phone but I'm not sure if I got a touchy one !(pardon the pun)!
ANY HELP/THOUGHTS VERY GRATEFULLY ACCEPTED
Further update - CAUSE !
I have found out the cause !
It happens when screen taps (sound) is turned on and is FINEwhen it is off. I only tuned this on last week !
SO what they heck this is some software bug perhaps - any thoughts ?
Thanks so much !
First my touch hd died suddenly two months before one year is over. So I sent in for repair and paid $20 for some sort of fee on the top of shipping in. When I get it back, I thought everything is doing fine. Then suddenly the screen started acting weir. It turns on sometimes but sometimes it won't. I tried master reset. I tried to contact Htc. And I even try to hit it since I was pretty upset getting this lemon.
I happen to have to travel to Taiwan and I took it to a cell phone store hoping they can fix it since it is a Taiwan phone. I got it back today and they said it will cost $170 to fix. And they said that I got liquid in. I have never let it get close to any water or liquid. Obviously they said the sensor was activated. (I don't even know there is a sensor for water).
Anyway, my phone now can call in but screen turns on when it likes to. While I am now playing with it. I turn all the auto backlight off, including with battery or power connected. And I also turn off the auto backlight sensor. Somehow for almost two hours, I can turn on anytime I want to and off any time. I do not how long it will last. If this is the problem, that means the software of auto backlight off has bugs. I hope this helps those who are like me lost some sleep over this HTC nightmare. I do not expect it is fixed at this point. May be I am just lucky that it stays controllable for the past two hours. Good luch y'all.

My Hero does the weirdest thing...

Sometimes, I'll place the handset down on a table or whatever, and completely of it's own accord, the screen will scroll right to the second page. Then a couple seconds later, it'll scroll right again to the third, and fourth. I'll pick it up and swipe back to the home screen and put it back down, and it'll do the same thing again. Basically.... wtf?
Sometimes it does it in menus aswell, scrolling down lists one by one every few seconds when the thing isn't even in my hands.
Has anyone else experienced this? I've had a couple of replacement handsets and it's done it on all of them!
Switchbitch said:
Sometimes, I'll place the handset down on a table or whatever, and completely of it's own accord, the screen will scroll left to the second page. Then a couple seconds later, it'll scroll left again to the third, and fourth. I'll pick it up and swipe back to the home screen and put it back down, and it'll do the same thing again. Basically.... wtf?
Sometimes it does it in menus aswell, scrolling down lists one by one every few seconds when the thing isn't even in my hands.
Has anyone else experienced this? I've had a couple of replacement handsets and it's done it on all of them!
Click to expand...
Click to collapse
It has happened to mine, intermittently. I was hoping that it was just a little piece of grit under the trackball and that it would stop, but now you've got me worried that it is a common fault. Mine is an unlocked white in the UK, bought from Devicewire and delivered around 10 days ago...
Yup, I can comfirm it has happened to me with 3 white sim free Heros. It can happen when the device is completely undisturbed so i'm assuming it's some weird software glitch.
I can't even identify what causes it, to recreate the conditions. Seems totally random.
Switchbitch said:
Yup, I can comfirm it has happened to me with 3 white sim free Heros. It can happen when the device is completely undisturbed so i'm assuming it's some weird software glitch.
I can't even identify what causes it, to recreate the conditions. Seems totally random.
Click to expand...
Click to collapse
Hopefully a (rapid) firmware upgrade will sort it...
Could it be something on the touch screen?
I think I have seen this too! Do we all have screen protectors on? I do on my Hero....
It seems to me like the people widget caused me some issues. I have removed it and the device is faster and this bug hasn't appeared for me at all since.
The Jones said:
I think I have seen this too! Do we all have screen protectors on? I do on my Hero....
It seems to me like the people widget caused me some issues. I have removed it and the device is faster and this bug hasn't appeared for me at all since.
Click to expand...
Click to collapse
Screen protector, yes. And the People widget (which I find very useful!)
Speaking about really weird things going on with the Hero. I can contribute with some funky stuff too:
When having my Hero near/under my mousecable the mousepointer (on the monitor) gets its own life. It starts moving randomly and begins to scroll the pages up and down in my browser WITHOUT me touching anything. I do have a cable connected mouse (USB). The phone has wifi, GPS and Network activated. I have not yet tested what happens with those turned off though.
Haha this is getting interesting. I noticed some mousepointer jitter when I was using the PC at work today, with my Hero nearby. I'll investigate more today.
Mine doesn't have a screen protector, but I do use the people widget on my second page. I'll remove it and see if it makes a difference to the spontaneous scrolling.
I just got my white unlocked hero 3 days ago and I just noticed this problem for the first time. The home screen would move over 1 or 2 screens without me even doing anything. Im wondering if it was major lag from previous movements I made. Im sure this is a software bug, does anyone know if HTC releases software updates for their android devices? I just switched from an iphone and hope they would release updates and fixes like apple did when something was wrong with a software release.
This phone is what... a week since launch day? We are early adopters and will find bugs. There'll be an update soon I'm pretty sure.
I think there is some interference with Wifi/Other radio and the Hero screen.
When i put mine on my desk next to my PC i cannot press all buttons on the touch screen but the wheel and hardware keys still work. When i move it 1m away from my PC this behavior is gone.
This problem happened to me when I had wet hands. All I did was wipe the hero dry and it worked fine again.
Thiesen said:
Speaking about really weird things going on with the Hero. I can contribute with some funky stuff too:
When having my Hero near/under my mousecable the mousepointer (on the monitor) gets its own life. It starts moving randomly and begins to scroll the pages up and down in my browser WITHOUT me touching anything. I do have a cable connected mouse (USB). The phone has wifi, GPS and Network activated. I have not yet tested what happens with those turned off though.
Click to expand...
Click to collapse
This is due to the phones aggressively high SAR value (it's really really high). I would think twice before putting this phone in your pant pockets if you ever want to have chidren
Ovek said:
This is due to the phones aggressively high SAR value (it's really really high). I would think twice before putting this phone in your pant pockets if you ever want to have chidren
Click to expand...
Click to collapse
Wow, really? I already have 2 so going to keep this in my pocket from now on!!!
Aaaaaaaand HTC didn't bother fixing this in the new rom. The T9 keyboard input bug and huge lag are also unchanged.
I can confirm that this odd bug still lurks around in the official 2.73.405.5 build.
It has been suggested that it migh be due to dirt inside the trackbal housing but then why would the homescreen suddenly scroll on its own without being touched? Maybe a sensor glitch? I don't know what solution HTC are using to read the movements of the trackball though... one thing is for sure; it's not a good one....
I'm 100% sure now it's not a hardware issue. It's happened on multiple Heros I've used, not long out the box either. The only thing I've noticed that indicates any kind of pattern to the apparent randomness is that it gets a lot worse when there's a lot of mobile data transfer going on. One time I physically couldn't get it to stay on the homescreen long enough to click an icon.
Just pitching in, exact same problem here. Very strange that everyone gets it to the right :/
Just notice on mine too, some automovement in menu and home
Upgraded yesterday to new firmware (modaco)
Could be an increase of trackball sensibili? I see a settings to tweak it on blackberry device...on android?

[Q] Bottom half of screen not responding to touch

I had an exam and removed the battery for my phone for the duration. When I put it back in, the bottom half of my screen stopped responding to touch. The screen itself is unharmed and uncracked. The S Pen still works flawlessly. However, the bottom half of the screen ("above" about 890 pixels on the Y axis) simply does not respond to normal touch. In addition, the volume buttons no longer change my notification volume. They still work for music volume, just not touch volume. When I long-press the power button, the power menu sits at the very top of the screen and has black covering the whole bottom of the screen for some reason. When I receive calls, the buttons are right at the top. Because of this, this seems to be some sort of software issue, but I have no idea what would cause it. Has anyone with more experience with Samsung devices seen this before? Multiple restarts and battery pulls have done nothing.
EDIT: In case anyone else encounters this, it had something to do with my case. I think my phone thought it was a smart cover for some reason. I enabled and disabled smart cover and then removed and replaced the case. It's working fine now.
EDIT: Never mind, that was a coincidence. The issue is DEFINITELY that the phone thinks it has a smart cover on it, but it has nothing to do with my own case.
gilros said:
I had an exam and removed the battery for my phone for the duration. When I put it back in, the bottom half of my screen stopped responding to touch. The screen itself is unharmed and uncracked. The S Pen still works flawlessly. However, the bottom half of the screen ("above" about 890 pixels on the Y axis) simply does not respond to normal touch. In addition, the volume buttons no longer change my notification volume. They still work for music volume, just not touch volume. When I long-press the power button, the power menu sits at the very top of the screen and has black covering the whole bottom of the screen for some reason. When I receive calls, the buttons are right at the top. Because of this, this seems to be some sort of software issue, but I have no idea what would cause it. Has anyone with more experience with Samsung devices seen this before? Multiple restarts and battery pulls have done nothing.
EDIT: In case anyone else encounters this, it had something to do with my case. I think my phone thought it was a smart cover for some reason. I enabled and disabled smart cover and then removed and replaced the case. It's working fine now.
Click to expand...
Click to collapse
I've had much the same problem. While the S-Pen was able to make selections that the touchscreen wouldn't, other S-Pen functions such as Air Command and being able to start an Action Memo wouldn't work. Waiting for an extended period of time (like 24 hours) and all of a sudden it started working again. However, while I was waiting, rebooting - even performing a factory reset - didn't' fix it! I just now rebooted it and it's not working again, and it's not in a case.
Where do you find the option to enable and disable Smart Cover? On the Note 2, it was (apparently) under Security / Device Administrators, but I don't find it there. The only option I could find was in Accessories / S View Cover / Automatic Unlock but changing this setting (including rebooting between settings) hasn't solved it.
hiroller173 said:
I've had much the same problem. While the S-Pen was able to make selections that the touchscreen wouldn't, other S-Pen functions such as Air Command and being able to start an Action Memo wouldn't work. Waiting for an extended period of time (like 24 hours) and all of a sudden it started working again. However, while I was waiting, rebooting - even performing a factory reset - didn't' fix it! I just now rebooted it and it's not working again, and it's not in a case.
Where do you find the option to enable and disable Smart Cover? On the Note 2, it was (apparently) under Security / Device Administrators, but I don't find it there. The only option I could find was in Accessories / S View Cover / Automatic Unlock but changing this setting (including rebooting between settings) hasn't solved it.
Click to expand...
Click to collapse
Sadly, it was just coincidence that it randomly stopped happening when I enabled and disabled the auto-unlock feature with Smart Cover. My phone started doing it again and I've been unable to repair it. I went to Verizon and they wiped my phone before telling me I'll just have to get it replaced with a refurbished one. Very frustrated. Shame there aren't any AOSP based ROMs yet (like CyanogenMod)-- they'd probably fix it since the cover thing wouldn't be a feature.
Bump.
Anyone know of the APK which would handle S View Cover behavior? If we were to disable that I imagine the problem would go away. I'm still not totally sure of the origin of the issue, but it seems to come from a combination of hardware and software problems. The hardware sensor thinks I have the case on, so the software changes things around. When I call people, I get the S View Cover style call screen. If I change the toggle in accessory settings to automatically unlock the phone when opening the cover, hitting the lock button automatically unlocks the phone as though I had no lockscreen. However, when this is disabled, the lock screen is NOT in the S View Cover form-- it looks stock. This confuses me.
Any ideas from anyone else getting the issue?
Same experience
Just to add my experience as I go. This afternoon I received an error that my SMS data could not be downloaded. Upon sliding down the notifications I was unable to control much. I ripped the majority of my hair out over this.... My pen works flawlessly everywhere though. I eventually discovered it works fine on the bottom half as you described. I have to run to some appointments, but I'll touch back after I try a few things.
gilros said:
Bump.
Anyone know of the APK which would handle S View Cover behavior? If we were to disable that I imagine the problem would go away. I'm still not totally sure of the origin of the issue, but it seems to come from a combination of hardware and software problems. The hardware sensor thinks I have the case on, so the software changes things around. When I call people, I get the S View Cover style call screen. If I change the toggle in accessory settings to automatically unlock the phone when opening the cover, hitting the lock button automatically unlocks the phone as though I had no lockscreen. However, when this is disabled, the lock screen is NOT in the S View Cover form-- it looks stock. This confuses me.
Any ideas from anyone else getting the issue?
Click to expand...
Click to collapse
gilros said:
Any ideas from anyone else getting the issue?
Click to expand...
Click to collapse
Maybe it was caused by the battery insertion or backplate replacement. Perhaps too much pressure or an uneven pressure damaged the circuitry, which is now loose and causing the intermittent error.
Or perhaps it was a static discharge from the battery.
Both cases seem to me to be warrenty items.
SGH-I717/SM-N900V/XDA Premium
Uh oh... I'm rooted and on Verizon. There isn't a way to unroot yet is there?
Frank Westlake said:
Maybe it was caused by the battery insertion or backplate replacement. Perhaps too much pressure or an uneven pressure damaged the circuitry, which is now loose and causing the intermittent error.
Or perhaps it was a static discharge from the battery.
Both cases seem to me to be warrenty items.
SGH-I717/SM-N900V/XDA Premium
Click to expand...
Click to collapse
thematt917 said:
Uh oh... I'm rooted and on Verizon. There isn't a way to unroot yet is there?
Click to expand...
Click to collapse
I thought the only thing necessary to unroot is to flash the stock ROM. The download is linked from the de la Vega post.
SGH-I717/SM-N900V/XDA Premium
I realized had about 3 days left on my Best Buy (elite+) 45 day return. Swapped for a brand new one :good: with no issues!
Frank Westlake said:
I thought the only thing necessary to unroot is to flash the stock ROM. The download is linked from the de la Vega post.
SGH-I717/SM-N900V/XDA Premium
Click to expand...
Click to collapse
gilros said:
I had an exam and removed the battery for my phone for the duration. When I put it back in, the bottom half of my screen stopped responding to touch. The screen itself is unharmed and uncracked. The S Pen still works flawlessly. However, the bottom half of the screen ("above" about 890 pixels on the Y axis) simply does not respond to normal touch. In addition, the volume buttons no longer change my notification volume. They still work for music volume, just not touch volume. When I long-press the power button, the power menu sits at the very top of the screen and has black covering the whole bottom of the screen for some reason. When I receive calls, the buttons are right at the top. Because of this, this seems to be some sort of software issue, but I have no idea what would cause it. Has anyone with more experience with Samsung devices seen this before? Multiple restarts and battery pulls have done nothing.
EDIT: In case anyone else encounters this, it had something to do with my case. I think my phone thought it was a smart cover for some reason. I enabled and disabled smart cover and then removed and replaced the case. It's working fine now.
EDIT: Never mind, that was a coincidence. The issue is DEFINITELY that the phone thinks it has a smart cover on it, but it has nothing to do with my own case.
Click to expand...
Click to collapse
I have the same issue. I ve been trying to understand why this happened but no luck. I tried everything from updating to reseting. I first noticed it when i took the battery out as well. but the problem kinda fixed it self so i thought the phone has a spaz or something. but when i removed the battery again it happened again.
I took it to the people i bought it from and all they can say is cause there were a couple of scratches on the side of the case that it may not fall under warranty...
i was pretty angry cause its only two months old and the warranty is for a year. and the problem started happening while i was overseas so its been like that for almost a month. hopefully the sales guy is just talk cause its not up to him its just his "opinion" as he put it.
Did they explain to you why this happened? or if this is a common issue?
Hope your new phone is ok
I have this problem intermittently also. Exactly as described above.
Sent from my SM-N900V using Tapatalk
any updates on this? im having the same problem now with my tmobile version. it fell facedown and the extended battery i had it in fell out. im going to try putting an aosp rom on it when i get home from work.
Timely post! I gave up. Verizon sending me a warranty replacement to arrive today.
Sent from my SM-N900V using Tapatalk
I have the solution!
Please. Let me know it worked for you, so people that doesn´t like to post and only read can solve this problem.
The Problem:
The half bottom screen is not working. Including the back button, the option button and the home buttom. they only work if you use the S Pen. Except for the home button. The volumes button do not work either. So the Solution is this..
take off the battery while the phone is on. YES, do not turn off the telephone and the take off the battery. Just take off the battery while the phone is on. It should work. I hope this is the solution.
One more thing. Do not allow your phone to dried up the battery completly so this wont happen again. It is better to turn it off before it dries up.!
Please let me know if it worked for you! I will let you know if this problems start again and if was only an coincidence.Hopes it not!
This tough me a good lesson! never buy a Phone from not trusted retailer, it is better to pay the full price a good store. The people that sold me the phone has a crappy warrraty like if the screen it cellphone is complete off they wont allow me to use the warranty and my phone had faulty battery conecction so it was off. then I paid 100 dollars to be repaired then this problem.
Ok, guys please let us know if it worked so people start saving their phone
Just happened to mine as well
Hard reset didn't work, on the phone with support trying to request a replacement now.
Finally Solved!
Hi
I had same problem
I did everything u said like:
mega wipe and changing rom
custom roms
taking out battery when it's on ( I Did this but I don't know It had any effects on my phone or not!)
taking out external card
But I still Had the Problem
Solution:
But I had a flip cover and I separated that from phone and thanks God,surprisingly It's Fixed and it works like a charm!!! after that I used my original cover and there is no problem till now.
Good Luck
Had the same problem of touch not working.
I tried everything as suggested by the members but my Note 3 is still not working right.Touch not responding all of a sudden in the bottom part of screen after i removed the battery for sim change. Please suggest something.
luas_13 said:
I tried everything as suggested by the members but my Note 3 is still not working right.Touch not responding all of a sudden in the bottom part of screen after i removed the battery for sim change. Please suggest something.
Click to expand...
Click to collapse
I haven't gone back to refresh my memory but it seems to me that all these occurrances were caused by removing the back cover. Try removing it and the battery and firmly press on every spot with your thumb. First place the device face down on table padded with a single layer of a blanket. Remove the SIM and SD card and firmly reinsert. Press the back cover on and try it, then return it for warranty if it is still bad.
Frank
I also was faced with this issue today at the start of my morning BUT I FOUND A SOLUTION
I have a Sprint Galaxy Note 3 N900P Stock ROM/ no root, no mods/custom kernels/boots etc...
My device side effects were
The bottom half of my screen was not responding to my fingers,
When you press the Power Button, The options appeared on the top section of the screen instead of being the center
When I press the volume up/down keys, The volume would raise and lower, But the screen that pops up and shows you the volume had increased or decreased didnt show up
Only way to use device was with S Pen
Basically all the issues everyone listed, I had them.
Now my solution; if the issue is a hardware issue.
After dissembling my phone to see what each hardware part of the phone controls, I've come to the conclusion that there was an issue with my USB Dock Connector section of the phone. I uploaded a image pointing which connector controls it. I tried to just wipe and clean it up a bit because mines had some residue on the underneath of it. Then I plugged it back in and it started back to work %100. After I tried restarting it a few times and shaking the device up, it still works; Although I am still going to order a replacement USB Charging Port with flex cable just in case.
fixed.
This is the definitely the hardware problem.
most likely happen if u ever dropped ur phone to the ground ----------- and reboot ur phone some what later time. (can be days or months).
Temp Solution to this problem is...
face down your phone to the flat floor or a table, gently hit the back, strong enough to shock the devide, but not that strong to crack your screen.
one other simple way is to drop your phone to the floor, screen is facing down, from about 30 cm high from the floor.
"simply, hit your device like you used to fix your ur old TV. "
that is just a temp. GL.

Categories

Resources