[SOLVED]HELP! briked mate 8 ,no OS! - Mate 8 General

after formating data i think i failed to flash emui5 and after reboot i stuck in [ur device has been unlocked and cnt trusted] page
also download latest firmware not working in eRecovery
dload not working! it stuck in ur device is booting now...
so i need to boot into fastboot to flash twrp but i dont know how, i tried holding power+vol down but it not working i guess!
any ideas?

amin318 said:
after formating data i think i failed to flash emui5 and after reboot i stuck in [ur device has been unlocked and cnt trusted] page
also download latest firmware not working in eRecovery
dload not working! it stuck in ur device is booting now...
so i need to boot into fastboot to flash twrp but i dont know how, i tried holding power+vol down but it not working i guess!
any ideas?
Click to expand...
Click to collapse
connect usb Cable first then press power + volume down

amin318 said:
after formating data i think i failed to flash emui5 and after reboot i stuck in [ur device has been unlocked and cnt trusted] page
also download latest firmware not working in eRecovery
dload not working! it stuck in ur device is booting now...
so i need to boot into fastboot to flash twrp but i dont know how, i tried holding power+vol down but it not working i guess!
any ideas?
Click to expand...
Click to collapse
NXT-AL00C17B573 (Official) Huawei Mate 8 Firmware Android 7.0 EMUI 5.0
Step by Step Guide
1.
Download these 3 files (update.zip, update_data_full_cmcc_cn.zip, supersu_v2.79_sr2.zip)
1.1- http://update.hicloud.com:8180/TDS/data/files/p3/s15/G1255/g104/v71280/f1/full/update.zip
1.2- http://update.hicloud.com:8180/TDS/...80/f1/full/all/cn/update_data_full_all_cn.zip
1.3- http://www.sillanwali.com/downloads/supersu_v2.79_sr2.zip
2-
Copy these 3 files (update.zip, update_data_full_cmcc_cn.zip, update_data_full_all_cn.zip) into SD Card
3-
Download TWRP Recovery 3.0.3
http://sillanwali.com/downloads/twrp-3.0.3.img
4-
adb devices
adb reboot bootloader
fastboot flash recovery (PATH-TO)\twrp-3.0.3.img
5-
5.1- Reboot your phone to TWRP then choose Wipe > format > type Yes
5.2- Back again, then wipe (data, dalvik, cache, system)
5.3- Don't reboot after install
6-
Install
6.1- supersu_v2.79_sr2.zip (Don't reboot after install)
6.2- update_data_full_all_cn.zip (Don't reboot after install)
ignore unmounting \cust, userdata, system error
6.3- update.zip (Reboot when success)
7-
Factory Reset after success 100%. After that you will get NXT-AL10C17B573 (Official) Stock Firmware.
8-
HiSuite
8.1- Download HiSuite (http://consumer.huawei.com/minisite/HiSuite_en/index.html)
8.2- Install HiSuite on your Computer
9-
Download apk & Install Apps using HiSuite
9.1- Google Play Store
http://www.sillanwali.com/downloads/Google Play Store 7.4.12.L-all [0] [PR] 144479971.apk
9.2- Google Play Services
http://www.sillanwali.com/downloads/Google Play Services 10.0.84 (448-137749526).apk
9.3- Google Contacts Sync
http://www.sillanwali.com/downloads/Google Contacts Sync 7.1.1.apk
9.4- Google Calendar Sync
http://www.sillanwali.com/downloads/Google Calendar Sync 5.2.3-99827563-release.apk
10-
Did I help you? A ''thanks :good:'' would be highly appreciated

hamadazh said:
connect usb Cable first then press power + volume down
Click to expand...
Click to collapse
thats it thaaaaaaanks in advanced:fingers-crossed::fingers-crossed::fingers-crossed:

Related

How to install NXT-L29C432B560 (Official) Stock Firmware. (Guide with download links)

NXT-L29C432B560
Firmware: B560
Device name: Huawei Mate 8
Model number: Huawei NXT-L29
Build Number: NXT- L29C432B560
EMUI Version: 5.0
Android Version: 7.0
Region: Europe
Status: Official
Firmware
http://update.hicloud.com:8180/TDS/data/files/p3/s15/G753/g104/v73563/f1/full/update.zip
http://update.hicloud.com:8180/TDS/...3563/f1/full/hw/eu/update_data_full_hw_eu.zip
http://update.hicloud.com:8180/TDS/data/files/p3/s15/G753/g104/v73563/f1/full/filelist.xml
http://update.hicloud.com:8180/TDS/data/files/p3/s15/G753/g104/v73563/f1/full/changelog.xml
Changelog
This update optimizes system performance and stability, and fixes an issue where some UI elements were displayed incorrectly.
Optimizations
Decreases power consumption to prolong usage time. Improves system performance and stability for smoother operations. Optimizes the display in the status bar and notification panel, which now displays notifications more clearly. Integrates Google security patches for improved system security. [Fixes] Fixes an issue where no control buttons were displayed on the lock screen for third-party music apps. Fixes an issue where app icons were not being displayed for messages in the status bar. Fixes an issue where the text wasn't displayed clearly in third-party apps with a white background. Fixes an issue where call durations were not displayed in the call log. Fixes an issue where some UI elements were displayed incorrectly.
Update notes
1. We recommend that you back up any important data before updating and factory reset.
2. The system will restart after the update. This will take about 5 minutes.
3. The Barclays app quits mid-operation because it is incompatible with Android 7.0. Please download the latest compatible version when it is available.
4. If you experience any issues during the update, please call the Huawei customer service hotline or visit an authorized Huawei service center for assistance.
Dload Method 1
1- First, download ubdate.zip and extract it.
2- Now create a folder dload in the root of your SD card and place the update.app file in that folder.
3- Now go to the phone Settings>Update and press the menu button.
4- Now select choose Local update.
5- It will show the update.app file now tap on it to start the installation process.
6- Wait until the installation process is complete and then reboot your device.
7- Done
8- Did I help you? A ''thanks :good:'' would be highly appreciated
Dload Method 2
1- Download update.zip and extract it.
2- Now create a folder dload in the root of your SD card and place the update.app file in that folder.
3- Now turn off your device.
4- Now press 3 buttons (Volume Up, Volume Down and Power Button) together. The update process will start automatically.
5- Now wait for some time to complete the process.
6- Done.
7- Did I help you? A ''thanks :good:'' would be highly appreciated
HiSuite Method
All Users with NXT- L29C432BXX can update using HiSuite:
1- Install HiSuite
2- Download HiSuite (http://consumer.huawei.com/minisite/HiSuite_en/index.html)
3- Install HiSuite on your Computer
4- Connect your phone to HiSuite
5- Go to Update>
6- Now wait for some time to complete the process.
7- Done.
8- Did I help you? A ''thanks :good:'' would be highly appreciated
Step by Step Guide
1- Download these 3 files (update.zip, update_full_hw_eu.zip, supersu_v2.79_sr2.zip)
1.1- http://update.hicloud.com:8180/TDS/data/files/p3/s15/G753/g104/v73563/f1/full/update.zip
1.2- http://update.hicloud.com:8180/TDS/...3563/f1/full/hw/eu/update_data_full_hw_eu.zip
1.3- http://www.sillanwali.com/downloads/supersu_v2.79_sr2.zip
2- Copy these 3 files (update.zip, update_full_hw_eu.zip, supersu_v2.79_sr2.zip) into SD Card
3- Download TWRP Recovery
http://sillanwali.com/downloads/twrp-3.0.3.img
4- Run into Fastboot (https://forum.xda-developers.com/mate-8/general/fastboot-erecovery-recovery-upgrade-mode-t3543441)
adb devices
adb reboot bootloader
fastboot oem device-info
fastboot oem unlock ****************
To obtain bootloader unlock code, go to https://emui.huawei.com/en/plugin/unlock/index
Huawei ID is the account you use to access all Huawei services.
Log in to your Huawei ID. Phone/Email. Password ********
fastboot flash recovery (PATH-TO)\twrp-3.0.3.img
5- Reboot into Recovery Mode (https://forum.xda-developers.com/mate-8/general/fastboot-erecovery-recovery-upgrade-mode-t3543441)
5.1- Go to: Wipe > format > type Yes
5.2- Back again, then wipe> advance wipe> (data, dalvik, cache, system, internal data)
5.3- Don't reboot after wipe
6- Root & Firmware Installation
6.1- Install supersu_v2.79_sr2.zip (Don't reboot after install)
6.2- update_full_hw_eu.zip (Don't reboot after install)
ignore unmounting \cache, cust, system, userdata error
6.3- update.zip (Reboot when success)
ignore E:unknown command
7- Factory Reset & Relock Bootloader
7.1- Factory Reset after success 100%. After that you will get NXT-L29C432B560(Official) Firmware.
7.2- Run Fastboot Mode
fastboot oem relock ****************
7.3- Select yes from phone.
7.3- Your phone will be automatically Factory Reset.
8- Did I help you? A ''thanks :good:'' would be highly appreciated
Have you tried? Today's update is giving me an error when i try to install it "check_write_data_to_partition, write data error E:unknown command [errno] update_huawei_pkg_from_ota_zip: update package from zip failed"
The yesterday's update instead works but i got that nfc problem
Can I install on L09?
Giving it a try now.
---------- Post added at 05:36 PM ---------- Previous post was at 04:40 PM ----------
ImSpiderman said:
Have you tried? Today's update is giving me an error when i try to install it "check_write_data_to_partition, write data error E:unknown command [errno] update_huawei_pkg_from_ota_zip: update package from zip failed"
The yesterday's update instead works but i got that nfc problem
Click to expand...
Click to collapse
Getting the same thing on my end.
In TWRP, format data then it will write to data partition.
Do factory reset to reset data partition password.
If u r already on nougat, just dload and reboot
I tried to dload from nougat but it fails instantly. Also, when i tried installing this from twrp i formatted everything but sd before trying to install it
ImSpiderman said:
Have you tried? Today's update is giving me an error when i try to install it "check_write_data_to_partition, write data error E:unknown command [errno] update_huawei_pkg_from_ota_zip: update package from zip failed"
The yesterday's update instead works but i got that nfc problem
Click to expand...
Click to collapse
6-
Install
6.1- supersu_v2.79_sr2.zip (Don't reboot after install)
6.2- update_full_hw_eu.zip (Don't reboot after install)
ignore unmounting \cache, cust, system, userdata, error
6.3- update.zip (Reboot when success)
ignore E:unknown command
sillanwali said:
6-
Install
6.1- supersu_v2.79_sr2.zip (Don't reboot after install)
6.2- update_full_hw_eu.zip (Don't reboot after install)
ignore unmounting \cache, cust, system, userdata, error
6.3- update.zip (Reboot when success)
ignore E:unknown command
Click to expand...
Click to collapse
I just keep getting the same error flashing both update files, actually the installation of the full hw zip last like a minute but the update's installation just stops immediately after that error
Then you may have to try via PC hisuite
Or
Go back to 4.1 and flash fresh
What about NFC? it is added to settings or has this version the same bug as other 560 versions?
bluheart said:
Then you may have to try via PC hisuite
Or
Go back to 4.1 and flash fresh
Click to expand...
Click to collapse
im flashing with twrp from 4.1 everytime actually, also hisuite when i have old b560 says me that im on latest firmware
Got error 7 when trying to flash these two zips. Tried everything from installing from an OTG cable to internal storage, error 7 all the way.
All, maybe I am missing something....I am on Nougat already but would like to reflash 560 via TWRP due to the fact that dload isn't working (update aborted after 5%). Unfortunately even with a ok. after flashing recovery I am still on stock recovery....Please advice!
flyingjack said:
All, maybe I am missing something....I am on Nougat already but would like to reflash 560 via TWRP due to the fact that dload isn't working (update aborted after 5%). Unfortunately even with a ok. after flashing recovery I am still on stock recovery....Please advice!
Click to expand...
Click to collapse
Yes flash and wipe cache
---------- Post added at 12:21 PM ---------- Previous post was at 12:20 PM ----------
Faithnetic said:
Got error 7 when trying to flash these two zips. Tried everything from installing from an OTG cable to internal storage, error 7 all the way.
Click to expand...
Click to collapse
In TWRP, format data only then u will be able towards write on that partition.
bluheart said:
Yes flash and wipe cache
---------- Post added at 12:21 PM ---------- Previous post was at 12:20 PM ----------
Fastboot erase cache dosn't work....?????
Click to expand...
Click to collapse
after i format data, wiped everything but microsd it still gives error, also i need to add that before the error it says
"mountencrypt: failed to mount /data: no such file or directory" maybe we need to change data filesystem? or what? i really dont understand why both files wont flash, i flashed b521 and first b560 without problems of any kind
Same error 7 :SS
Then go back to 4.1 and relax for the next update
All, I need your help and advice....
I massed up my phone....I flashed TWRP but never been able to enter Recovery as "fastboot erase chache" did not work and ended up in a bootloop while trying to access Recovery...after several additional -stupied- tries I distroied my OS (5B60), menas I lost my key-board etc....
I still can connect via fastboot and/or adp but cannot clear cache. Therefore I am not able to enter TWRP and flash any softwrae. Dload doesn't work either as I donot have a stock recovery...
Please guide me back to a working phone
Thx a lot!!!
flyingjack said:
All, I need your help and advice....
I massed up my phone....I flashed TWRP but never been able to enter Recovery as "fastboot erase chache" did not work and ended up in a bootloop while trying to access Recovery...after several additional -stupied- tries I distroied my OS (5B60), menas I lost my key-board etc....
I still can connect via fastboot and/or adp but cannot clear cache. Therefore I am not able to enter TWRP and flash any softwrae. Dload doesn't work either as I donot have a stock recovery...
Please guide me back to a working phone
Thx a lot!!!
Click to expand...
Click to collapse
Try to relock bootloader and dload again, it should work

Huawei Mate 8 NXT-AL10C00B581 (Official) Latest Firmware. (Guide with download links)

NXT-AL10C00B581
Firmware (OTA)
http://update.hicloud.com:8180/TDS/data/files/p3/s15/G1255/g104/v74488/f1/full/update.zip
http://update.hicloud.com:8180/TDS/.../v74488/f1/full/all/cn/update_full_all_cn.zip
Changelog
Dear users, this update optimizes system performance and stability, repair Taobao application text dialog box to block the input method of the problem, it is recommended you update the experience.
Optimization
Optimize micro message grab red packets speed, so you grab red packets faster into Google security patches, improve system security
Fix
Fix the problem of microblogging slowdown after cleaning the small brush
Update Considerations:
1. Huawei recommended that you do a good job of backing up your data before updating.
2. After the update is complete, the system will restart, please be patient for about five minutes.
3. If you encounter any problems during the use, you can visit the "Member Services", "Pollen Club" or call the official service hotline 400-930-9300 for support.
Official way to update
All Users with NXT-AL10C00B552, NXT-AL10C00B562, NXT-AL10C00B573, NXT-AL10C00B575 and NXT-AL10C00B577 can update using Hi****e:
1- Install HiSuite
1.1- Download HiSuite (http://consumer.huawei.com/minisite/HiSuite_en/index.html)
1.2- Install HiSuite on your Computer
2- Connect your phone to HiSuite
3- Go to Update>
Step by Step Guide (For Rooted Phones)
1- Download these 3 files (update.zip, update_full_all_cn.zip, supersu_v2.79_sr2.zip)
1.1- http://update.hicloud.com:8180/TDS/data/files/p3/s15/G1255/g104/v74488/f1/full/update.zip
1.2- http://update.hicloud.com:8180/TDS/.../v74488/f1/full/all/cn/update_full_all_cn.zip
1.3- http://www.sillanwali.com/downloads/supersu_v2.79_sr2.zip
2- Copy these 3 files (update.zip, update_full_all_cn.zip, supersu_v2.79_sr2.zip) into SD Card
3- Download TWRP Recovery 3.0.3
http://sillanwali.com/downloads/twrp-3.0.3.img
4- Run into Fastboot (https://forum.xda-developers.com/mate-8/general/fastboot-erecovery-recovery-upgrade-mode-t3543441)
adb devices
adb reboot bootloader
fastboot oem device-info
fastboot oem unlock ****************
To obtain bootloader unlock code, go to https://emui.huawei.com/en/plugin/unlock/index
Huawei ID is the account you use to access all Huawei services.
Log in to your Huawei ID. Phone/Email. Password ********
fastboot flash recovery (PATH-TO)\twrp-3.0.3.img
5- Reboot into Recovery Mode (https://forum.xda-developers.com/mate-8/general/fastboot-erecovery-recovery-upgrade-mode-t3543441)
5.1- Go to: Wipe > format > type Yes
5.2- Back again, then wipe (data, dalvik, cache, system, internal data)
5.3- Don't reboot after wipe
6- Root & Firmware Installation
6.1- Install supersu_v2.79_sr2.zip (Don't reboot after install)
6.2- Install update_full_all_cn.zip (Don't reboot after install)
ignore unmounting \cust, userdata, system error
6.3- Install update.zip (Reboot when success)
7- Factory Reset & Relock Bootloader
7.1- Factory Reset after success 100%. After that you will get NXT-AL10C17B581 (Official) Firmware.
7.2- Run Fastboot Mode
fastboot oem relock ****************
7.3- Select yes from phone.
7.3- Your phone will be automatically Factory Reset.
8- Install HiSuite (Huawei Official PC Suite)
8.1- Download HiSuite (http://consumer.huawei.com/minisite/HiSuite_en/index.html)
8.2- Install HiSuite on your Computer
9- Download apk & Install Apps using HiSuite
9.1- Google Play Store
http://www.sillanwali.com/downloads/Google Play Store 7.4.12.L-all [0] [PR] 144479971.apk
9.2- Google Play Services
http://www.sillanwali.com/downloads/Google Play Services 10.0.84 (448-137749526).apk
9.3- Google Contacts Sync
http://www.sillanwali.com/downloads/Google Contacts Sync 7.1.1.apk
9.4- Google Calendar Sync
http://www.sillanwali.com/downloads/Google Calendar Sync 5.2.3-99827563-release.apk
10- Did I help you? A ''thanks :good:'' would be highly appreciated
<root>
<root>
<component>
<name>TCPU</name>
<compress>0</compress>
</component>
<vendorInfo name="common" subpath="" logfile="changelog.xml" package="update.zip"/>
<vendorInfo name="all/cn" subpath="all/cn" logfile="" package="update_full_all_cn.zip"/>
<vendorInfo name="public" subpath="public" logfile="" package="update_data_full_public.zip"/>
<vendorInfo name="telecom/cn" subpath="telecom/cn" logfile="" package="update_full_telecom_cn.zip"/>
<files>
<file>
<spath>update_full_all_cn.zip</spath>
<dpath>update_full_all_cn.zip</dpath>
<operation>c</operation>
<md5>81BDE095CCB0BBF95CEE6B856E30DFDB</md5>
<size>16799955</size>
</file>
<file>
<spath>changelog.xml</spath>
<dpath>changelog.xml</dpath>
<operation>c</operation>
<md5>0B92FF72BCB6F2AFF51146FFB3B03427</md5>
<size>1289</size>
</file>
<file>
<spath>update_data_full_public.zip</spath>
<dpath>update_data_full_public.zip</dpath>
<operation>c</operation>
<md5>81BDE095CCB0BBF95CEE6B856E30DFDB</md5>
<size>16799955</size>
</file>
<file>
<spath>update_full_telecom_cn.zip</spath>
<dpath>update_full_telecom_cn.zip</dpath>
<operation>c</operation>
<md5>81BDE095CCB0BBF95CEE6B856E30DFDB</md5>
<size>16799955</size>
</file>
<file>
<spath>update.zip</spath>
<dpath>update.zip</dpath>
<operation>c</operation>
<md5>0ED9DF3A0D6541BD238DE5034D756D3F</md5>
<size>81879850</size>
</file>
</files>
</root>
Source: http://update.hicloud.com:8180/TDS/data/files/p3/s15/G1255/g104/v74488/f1/full/filelist.xml
Did I help you? A ''thanks :good:'' would be highly appreciated
You are just too quick buddy
bluheart said:
You are just too quick buddy
Click to expand...
Click to collapse
You know it wasn’t always easy. Thank you!
nice, full B581! ill extract the boot image right away so it can get patched
edit: oooh, nevermind, still the OTA.... was getting excited already
Sent from my Huawei Mate 8 NXT-AL10
Lol jbmc
Is this final or still beta?
Enviado desde mi HUAWEI NXT-AL10 mediante Tapatalk
It's among final
its a dev release after the first final roms
...
Official way to update
All Users with NXT-AL10C00B552, NXT-AL10C00B562, NXT-AL10C00B573 and NXT-AL10C00B575 can update using Hi****e:
1- Install HiSuite
1.1- Download HiSuite (http://consumer.huawei.com/minisite/HiSuite_en/index.html)
1.2- Install HiSuite on your Computer
2- Connect your phone to HiSuite
3- Go to Update>
I don't know if someone has the same issue: I'm with NXT-AL10C00B575 (no root) and HiSuite does not propose at all B581 update ? Is there someone with the same situation and having found a solution to flash b581 update without rooting ?
a029159 said:
...
Official way to update
All Users with NXT-AL10C00B552, NXT-AL10C00B562, NXT-AL10C00B573 and NXT-AL10C00B575 can update using Hi****e:
1- Install HiSuite
1.1- Download HiSuite (http://consumer.huawei.com/minisite/HiSuite_en/index.html)
1.2- Install HiSuite on your Computer
2- Connect your phone to HiSuite
3- Go to Update>
I don't know if someone has the same issue: I'm with NXT-AL10C00B575 (no root) and HiSuite does not propose at all B581 update ? Is there someone with the same situation and having found a solution to flash b581 update without rooting ?
Click to expand...
Click to collapse
I am too i tried to update by hisuite doesn't work...
a029159 said:
...
Official way to update
All Users with NXT-AL10C00B552, NXT-AL10C00B562, NXT-AL10C00B573 and NXT-AL10C00B575 can update using Hi****e:
1- Install HiSuite
1.1- Download HiSuite (http://consumer.huawei.com/minisite/HiSuite_en/index.html)
1.2- Install HiSuite on your Computer
2- Connect your phone to HiSuite
3- Go to Update>
I don't know if someone has the same issue: I'm with NXT-AL10C00B575 (no root) and HiSuite does not propose at all B581 update ? Is there someone with the same situation and having found a solution to flash b581 update without rooting ?
Click to expand...
Click to collapse
1-
Enable USB Debugging on your phone:
1.1- Open Settings> About phone
1.2- Then tap “Build number” seven times to enable Developer options.
1.3- Go back to Settings menu and now you'll be able to see “Developer options” there.
1.4- Tap it and turn on USB Debugging from the menu on the next screen.
1.5- Restart your phone
2-
Install HiSuite
2.1- Download HiSuite (http://consumer.huawei.com/minisite/HiSuite_en/index.html)
2.2- Install HiSuite on your Computer
3-
Connect your phone to HiSuite
4-
Go to Update>Switch to other version>Developer
You can see latest beta version NXT-XXXXXXXXX (Developer) XXXMB, like this:
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
5-
Click on Update
6-
Did I help you? A ''thanks :good:'' would be highly appreciated
sillanwali said:
1-
Enable USB Debugging on your phone:
1.1- Open Settings> About phone
1.2- Then tap “Build number” seven times to enable Developer options.
1.3- Go back to Settings menu and now you'll be able to see “Developer options” there.
1.4- Tap it and turn on USB Debugging from the menu on the next screen.
1.5- Restart your phone
2-
Install HiSuite
2.1- Download HiSuite (http://consumer.huawei.com/minisite/HiSuite_en/index.html)
2.2- Install HiSuite on your Computer
3-
Connect your phone to HiSuite
4-
Go to Update>Switch to other version>Developer
You can see latest beta version NXT-XXXXXXXXX (Developer) XXXMB, like this:
5-
Click on Update
6-
Did I help you? A ''thanks :good:'' would be highly appreciated
Click to expand...
Click to collapse
Sorry but for me, in Hisuite, Developper option is "greyed" and not accessible !
a029159 said:
Sorry but for me, in Hisuite, Developper option is "greyed" and not accessible !
Click to expand...
Click to collapse
Same here. USB debugging is enabled and usually I can get the update through HiCare.
Sent from my HUAWEI NXT-AL10 using XDA-Developers Legacy app
I failed at step 6.3 install update.zip, E: unknown command (error), Updater process ended with ERROR: 7 Error installing zip file///
Phone doesn't boot in recovery after flashing recovery
Strange... after "fastboot flash recovery (PATH-TO)\twrp-3.0.3.img"" the twrp recovery is flashed but I am unable to boot into recovery.
It remains locked with the yellow warning message but it doesn't boot.
Any clue about the reason and how to fix it?
have you tried all button combinations? both when connected to a computer and disconnected?
total of three combos:
power + volume up
power + volume down
power + volume up + volume down
try all three in both states, im sure one of them will get u into the recovery
johnney said:
I failed at step 6.3 install update.zip, E: unknown command (error), Updater process ended with ERROR: 7 Error installing zip file///
Click to expand...
Click to collapse
aeas said:
Strange... after "fastboot flash recovery (PATH-TO)\twrp-3.0.3.img"" the twrp recovery is flashed but I am unable to boot into recovery.
It remains locked with the yellow warning message but it doesn't boot.
Any clue about the reason and how to fix it?
Click to expand...
Click to collapse
If u flash this u'll get no OS! Cus its just 70mb! It's not a full firmware!
If u where android 6 just use rescue fastboot to flash twrp for emui4 or 4.1 (based on ur last firmware)
Then u cn enter twrp to flash a real firmware
How to enter rescue fastboot ->turn off ur phone(there's a shutdown option in eRecovery power+vol up), connect usb then hold power+vol down
Sent from my NXT-L29 using Tapatalk
Thanks for your help.
I managed to restart using buttons and reinstalled all twrp 3. Everything working again as it was when I started.
Yes, I have also discovered that it is not a full rom, my great mistake but I didn't reach that point cause I stopped after I couldn't restart in TWRP recovery.
I am now in the process of knowing what is the right procedure I have to followed from my rom (KangVIP-Slim-B386-ViperAtmos) to a Nougat one.
aeas said:
Strange... after "fastboot flash recovery (PATH-TO)\twrp-3.0.3.img"" the twrp recovery is flashed but I am unable to boot into recovery.
It remains locked with the yellow warning message but it doesn't boot.
Any clue about the reason and how to fix it?
Click to expand...
Click to collapse
To enter Fastboot , eRecovery, Recovery or Upgrade mode:
Connect phone to the computer:
Fastboot mode: long press the volume down key + power button.
eRecovery mode: long press the volume up key + power button.
Do not connect to computer:
Recovery mode: long press the volume up key + power button.
Upgrade mode: long press the volume up key + volume down key + power button.
When the phone is in one of these modes, long press the power button to restart the phone.

How to install NXT-L29C605B580 (Official) Firmware. (Guide with download links)

NXT- L29C605B580
Firmware: B580
Device name: Huawei Mate 8
Model number: Huawei NXT-L29
Build Number: NXT- L29C605B580
EMUI Version: 5.0
Android Version: 7.0
Update Version: v75945
Region: Latin America
Firmware
http://update.hicloud.com:8180/TDS/data/files/p3/s15/G1582/g104/v75945/f1/full/changelog.xml
http://update.hicloud.com:8180/TDS/data/files/p3/s15/G1582/g104/v75945/f1/full/filelist.xml
http://update.hicloud.com:8180/TDS/data/files/p3/s15/G1582/g104/v75945/f1/full/update.zip
http://update.hicloud.com:8180/TDS/...04/v75945/f1/full/hw/la/update_full_hw_la.zip
http://update.hicloud.com:8180/TDS/...45/f1/full/public/update_data_full_public.zip
HiSuite Update Method
All Users with NXT- L29C605B*** can update using HiSuite:
1- Install HiSuite
2- Download HiSuite (http://consumer.huawei.com/minisite/HiSuite_en/index.html)
3- Install HiSuite on your Computer
4- Connect your phone to HiSuite
5- Go to Update>
6- Now wait for some time to complete the process.
7- Done.
8- Did I help you? A ''thanks :good:'' would be highly appreciated
Step by Step Guide (For Rooted Phones)
1- Download these 3 files (update.zip, update_full_hw_la.zip, supersu_v2.79_sr2.zip)
1.1- http://update.hicloud.com:8180/TDS/data/files/p3/s15/G1582/g104/v75945/f1/full/update.zip
1.2- http://update.hicloud.com:8180/TDS/...04/v75945/f1/full/hw/la/update_full_hw_la.zip
1.3- http://www.sillanwali.com/downloads/supersu_v2.79_sr2.zip
2- Copy these 3 files (update.zip, update_full_hw_la.zip, supersu_v2.79_sr2.zip) into SD Card
3- Download TWRP Recovery
http://www.sillanwali.com/downloads/twrp-3.0.2-0-next.img
http://sillanwali.com/downloads/twrp-3.0.3.img
4- Run into Fastboot (https://forum.xda-developers.com/mate-8/general/fastboot-erecovery-recovery-upgrade-mode-t3543441)
adb devices
adb reboot bootloader
fastboot oem device-info
fastboot oem unlock ****************
To obtain bootloader unlock code, go to https://emui.huawei.com/en/plugin/unlock/index
Huawei ID is the account you use to access all Huawei services.
Log in to your Huawei ID. Phone/Email. Password ********
fastboot flash recovery (PATH-TO)\**********.img
5- Reboot into Recovery Mode (https://forum.xda-developers.com/mate-8/general/fastboot-erecovery-recovery-upgrade-mode-t3543441)
5.1- Go to: Wipe > format > type Yes
5.2- Back again, then wipe> advance wipe> (data, dalvik, cache, system, internal data)
5.3- Don't reboot after wipe
6- Root & Firmware Installation
6.1- Install supersu_v2.79_sr2.zip (Don't reboot after install)
6.2- Install update_full_hw_la.zip (Don't reboot after install)
ignore unmounting \cust, userdata, system error
6.3- Install update.zip (Reboot when success)
7- Factory Reset & Relock Bootloader
7.1- Factory Reset after success 100%. After that you will get NXT- L29C605B580 (Official) Firmware.
7.2- Run Fastboot Mode
fastboot oem relock ****************
7.3- Select yes from phone.
7.3- Your phone will be automatically Factory Reset.
8- Did I help you? A ''thanks :good:'' would be highly appreciated
I got the hisuite error " no internet conection"
edit: in updater, the url was wrong. Upgrading.
thanks
re edit: when finish download and install from hisuite, cell restart and try install the rom, but fail, said file is not compatible
I came from C605 B100
sillanwali said:
NXT- L29C605B580
HiSuite Update Method
All Users with NXT- L29C605B*** can update using HiSuite:
Click to expand...
Click to collapse
I'm from b100 and can't install it, fail install error (in phone)
Is fingerprint working with this rom?
senseijulio said:
I'm from b100 and can't install it, fail install error (in phone)
Click to expand...
Click to collapse
You need to be in B131
Can this be used on L29C432?
Sent from my HUAWEI NXT-L29 using Tapatalk
Bromsoket said:
Can this be used on L29C432?
Sent from my HUAWEI NXT-L29 using Tapatalk
Click to expand...
Click to collapse
I wonder the same
It Will work with any area , just make sure u have oem and cust installed to 605
I'm on rooted B560 and already have twrp 3.0.3 can I just flash the superuser and zip files straight away or do I have to reflash the twrp and do factory reset first?
And there are 2 twrp's in the list, is both needed? If yes should i flash 3.0.2 first and then 3.0.3 directly after ?
Sent from my HUAWEI NXT-L29 using Tapatalk
Tried to flash this in twrp got error 7
does this guide work for c438 also ?
Nougat Update
I received my OTA update to nougat yesterday through 2 updates. The first update I received and downloaded was
nxt-l29c185b200 and the file size was about 717mb. Afterwards about 2 minutes later I received the official update for nougat and the file size was about 2.2GB. I was surprised when I saw the first update as I wasn't expecting it. The update came at a good time because I was just about to buy a new phone.
bm3epps said:
I received my OTA update to nougat yesterday through 2 updates. The first update I received and downloaded was
nxt-l29c185b200 and the file size was about 717mb. Afterwards about 2 minutes later I received the official update for nougat and the file size was about 2.2GB. I was surprised when I saw the first update as I wasn't expecting it. The update came at a good time because I was just about to buy a new phone.
Click to expand...
Click to collapse
B560 is from august!! its old stuff now.. but congrats. the nougat update is like getting a new phone
sillanwali said:
NXT- L29C605B580
Firmware: B580
Device name: Huawei Mate 8
Model number: Huawei NXT-L29
Build Number: NXT- L29C605B580
EMUI Version: 5.0
Android Version: 7.0
Update Version: v75945
Region: Latin America
3- Download TWRP Recovery
http://www.sillanwali.com/downloads/twrp-3.0.2-0-next.img
http://sillanwali.com/downloads/twrp-3.0.3.img
Click to expand...
Click to collapse
Why this TWRP?
Why not this one? I think we will not have error with it.
senseijulio said:
i got the hisuite error " no internet conection"
edit: In updater, the url was wrong. Upgrading.
Thanks
re edit: When finish download and install from hisuite, cell restart and try install the rom, but fail, said file is not compatible
i came from c605 b100
Click to expand...
Click to collapse
hi, wich url u put? Thanks
HansCZ said:
You need to be in B131
Click to expand...
Click to collapse
IM in b131, but i didnt recive the update yet, what can i do? im search and search and nothing

Lost /data partition, cannot flash stock rom

HTML:
[QUOTE][/QUOTE]
Hi
I have bricked my phone with a failed TWRP install. The data partition became corrupted and I need to restore. I have tried to move UPDATE.zip via ADB but phone says not enough space. Should I flash new img files (system, data)? If so, where can I get these? My model is VNS-L22 dual SIM.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Thanks
Did you try with dload from sd card ? you can try to find a rom with firmware finder-here or from http://pro-teammt.ru-here, its best to download FullOTA-MF-PV version.
You can always try this Huawei Multi-Tool 8
I'm in simmilar situation. Cannot format, convert /data partiton.
Not sure which version of ROM I've had. Probably stock B504 -> EliteROM - fault with boot --> tried app back to stock and now from version from shown by some adb command B130.
Which version should I put inyo dload to start getting back to stock?
TyDraniu said:
I'm in simmilar situation. Cannot format, convert /data partiton.
Not sure which version of ROM I've had. Probably stock B504 -> EliteROM - fault with boot --> tried app back to stock and now from version from shown by some adb command B130.
Which version should I put inyo dload to start getting back to stock?
Click to expand...
Click to collapse
Hi dude,
if you try to be a little more detailed
about the recovery you used and the last stock firmware you had
and what you did trying to get back from EliteRom maybe,
I say maybe someone could help you...
Cheers
The thing is that I'm not sure
I've tried so many combination that I'm not sure what was the last.
Last working soft was latest official firmware from huawei p9 lite in Poland - I think it was B504.
Then I've tried to install [Elite ROM][EMUI 5.1.1] Elite ROM v7.7 - it wont boot up, i've get bootloop.
Then I tried to use dload folder to get back to stock - VNS-L21C432B130 it was installed succesfully but system wont boot up - bootloop again.
TyDraniu said:
The thing is that I'm not sure
I've tried so many combination that I'm not sure what was the last.
Last working soft was latest official firmware from huawei p9 lite in Poland - I think it was B504.
Then I've tried to install [Elite ROM][EMUI 5.1.1] Elite ROM v7.7 - it wont boot up, i've get bootloop.
Then I tried to use dload folder to get back to stock - VNS-L21C432B130 it was installed succesfully but system wont boot up - bootloop again.
Click to expand...
Click to collapse
Ok man i will try to help you but beginning from now
you should do one thing at a time...
Due the fact you tried to flash B130 your bootloader could be re-locked again,
so boot into the fastboot mode and unlock it again... the device should restart in TWRP recovery mode...
Once you're in TWRP tap WIPE > FACTORY RESET > restart system.
If won't boot it need to be unbricked...
PHONE: Unlocked
FRP: Unlocked
In this moment there is no TWRP:
power + vol + = EMUI: reboot, wipe, wipe.
TyDraniu said:
PHONE: Unlocked
FRP: Unlocked
In this moment there is no TWRP:
power + vol + = EMUI: reboot, wipe, wipe.
Click to expand...
Click to collapse
Dude boot into the EMUI e-recovery and do a factory reset + wipe cache..
Doesn't it boot to system ?
It doesn't.
After boot it's stuck on black screen.
TyDraniu said:
It doesn't.
After boot it's stuck on black screen.
Click to expand...
Click to collapse
Boot into the fastboot mode and unlock again the bootloader.
Try then to reboot to system.
As I said bootloader is unlocked. When I've executed : fastboot oem get-bootinfo i've received: (bootloader) unlocked
when i've executed: fastboot oem unlock "my_unlock_code" i've received FAILED (remote: already fastboot unlocked)
other suggestions?
--------------------------------
I'm not sure if it's a progress but...
1. fastboot: flash working twrp
2. twrp flash oeminfo.img for L21c432 DS
3. restart - auto factory reset
4. Flash with Multi-Tool: boot, system, recovery, cust from b160
5. put into SDcard dload\update.app from b160
6. phone started booting and goes to huawei logo with some shiny effect - and stuck on it .....
What I'm doing wrong?
TyDraniu said:
As I said bootloader is unlocked. When I've executed : fastboot oem get-bootinfo i've received: (bootloader) unlocked
when i've executed: fastboot oem unlock "my_unlock_code" i've received FAILED (remote: already fastboot unlocked)
other suggestions?
--------------------------------
I'm not sure if it's a progress but...
1. fastboot: flash working twrp
2. twrp flash oeminfo.img for L21c432 DS
3. restart - auto factory reset
4. Flash with Multi-Tool: boot, system, recovery, cust from b160
5. put into SDcard dload\update.app from b160
6. phone started booting and goes to huawei logo with some shiny effect - and stuck on it .....
What I'm doing wrong?
Click to expand...
Click to collapse
Seems all good, apart after you flashed oeminfo.img you have to flash custom.bin file together.
(maybe you need the TOOLKIT (take august 2017 release) to flash oeminfo.img&custom.bin files)
This should re-lock the bootloader, so when the process ends, reboot to fastboot , unlock again
the bootloader and forwards with the other steps..
At the end of the whole process reboot to recovery and do a factory reset + clear cache...
"(maybe you need the TOOLKIT (take august 2017 release) to flash oeminfo.img&custom.bin files)" - to do it I have to put phone into ADB mode.
oeminfo.zip I can flash in TWRP.
I don't know how to flash custom.bin
TyDraniu said:
"(maybe you need the TOOLKIT (take august 2017 release) to flash oeminfo.img&custom.bin files)" - to do it I have to put phone into ADB mode.
oeminfo.zip I can flash in TWRP.
I don't know how to flash custom.bin
Click to expand...
Click to collapse
Hi dude,
so look into the zip oeminfo.
If there are both oeminfo.img and custom.bin files
you are ok to flash in TWRP.
( in your previous post you wrote you flashed oeminfo.img file, not flashable zip )
If into the zip there is only oeminfo.img file you need that custom.bin file.
In oeminfo.zip file there is always only oeminfo.img and some other config files.
Every time when I find custom.bin it is always a standalone file. I cannot find zip to flash on TWRP with custom.bin
TyDraniu said:
In oeminfo.zip file there is always only oeminfo.img and some other config files.
Every time when I find custom.bin it is always a standalone file. I cannot find zip to flash on TWRP with custom.bin
Click to expand...
Click to collapse
Don't know dude, maybe you used some wrong files...
This time use this steps:
Install and use TWRP 3.0.2-0 ( this should be Meticulus recovery )
THIS oeminfo.zip file is a L21C432DS flashable one ( took from htcmania site )
The direct LINK to download L21C432B160 update.zip ( using FIRMWARE FINDER )
from with extract update.app and use DLOAD method.
1 - Reboot recovery and flash the oeminfo.zip file.
2 - Once finished the device should reboot to twrp recovery.
3 - Power off the device. Extract the SD card and with your PC format it. ( backup your files )
4 - Create the DLOAD folder in your SD and paste update.app you extracted from update.zip into it.
5 - Put the SD into the device and use three buttons ( vol+&vol-&power ) to start the flash process.
6 - When finished reboot to e-recovery ( vol+ and power buttons ) and do factory reset + clear cache.
7 - Dude you should be ok now.
P.S.: THIS oeminfo.zip is took from @k1ll3r8e personal repo ( can be flashed with the toolkit in fastboot mode )
Unlocked bootloader, TWRP 3.0.2-0 (Meticulus recovery ) installed.
1. - Reboot recovery and flash the oeminfo.zip file. - done
2 - device doesn't reboot, I've rebooted it manually - reboot recovery.
"Your device has failed verification" appeared and device boot into huawei recovery (options: reboot, wipe data/factory and wipe cache).
3. no option to turn off.
4. I've made SDcard.
5. restart by power and vol+ and vol - : installing update.............
6. When finished phone restarted automatically, i've pressed vol+ and got into recovery, done wipe data/fr and wipe cache and reboot ............... and ....................... black screen.
Now I'm waiting to be sure ~ 15 minutes...
Without any changes.
I've tried the same with B130 - same result. From power on there is logo huawei na blank screen with wisible backlight.
Any ideas?
TyDraniu said:
Unlocked bootloader, TWRP 3.0.2-0 (Meticulus recovery ) installed.
1. - Reboot recovery and flash the oeminfo.zip file. - done
2 - device doesn't reboot, I've rebooted it manually - reboot recovery.
"Your device has failed verification" appeared and device boot into huawei recovery (options: reboot, wipe data/factory and wipe cache).
3. no option to turn off.
4. I've made SDcard.
5. restart by power and vol+ and vol - : installing update.............
6. When finished phone restarted automatically, i've pressed vol+ and got into recovery, done wipe data/fr and wipe cache and reboot ............... and ....................... black screen.
Now I'm waiting to be sure ~ 15 minutes...
Without any changes.
I've tried the same with B130 - same result. From power on there is logo huawei na blank screen with wisible backlight.
Any ideas?
Click to expand...
Click to collapse
Damn, my apologies dude :angel:,
i forgot a line between point 1 & 2, let's call it 1.1.
So > 1.1 - After you flash oeminfo.zip go in main menu of TWRP
and tap reboot then bootloader.
Connect to pc and unlock again the bootloader.
Proceed with point 2....
1. - Reboot recovery and flash the oeminfo.zip file. - done
1.1 - After flash oeminfo.zip go in main menu of TWRP, reboot to bootloader, connect to pc and unlock again the bootloader.
2 - device reboot to twrp.
3. turn off.
4. I've made SDcard.
5. restart by power and vol+ and vol - : installing update.............
6. When finished phone restarted automatically, i've pressed vol+ and got into recovery, done wipe data/fr and wipe cache and reboot and power on there is logo huawei na blank screen with wisible backlight.... again
Everything goes as You wrote...
I'm loosing rest of hope...
Maybe it's physicaly broken somehow?!
TyDraniu said:
1. - Reboot recovery and flash the oeminfo.zip file. - done
1.1 - After flash oeminfo.zip go in main menu of TWRP, reboot to bootloader, connect to pc and unlock again the bootloader.
2 - device reboot to twrp.
3. turn off.
4. I've made SDcard.
5. restart by power and vol+ and vol - : installing update.............
6. When finished phone restarted automatically, i've pressed vol+ and got into recovery, done wipe data/fr and wipe cache and reboot and power on there is logo huawei na blank screen with wisible backlight.... again
Everything goes as You wrote...
I'm loosing rest of hope...
Maybe it's physicaly broken somehow?!
Click to expand...
Click to collapse
Hope no dude...
Try the rollback package, maybe something gone wrong going from android 7 to android 6.
THIS is the L21 rollback package (C900B300)
With your PC format the SD card nd create a DLOAD folder.
Extract update.app from the package, put it in the DLOAD folder and do three buttons method.
When finished turn off the device and extract the SD.
Remove the update.app from DLOAD folder and paste the update.app you
extracted from update.zip (B160) into it.
Boot again with three button method to flash the firmware..
The same, reboot to e-recovery and do factory reset + clear cache..
Hope this will work.

TWRP does not work on B03 a2017g

Anyone succeed flashing TWRP for this build? I flashed this update through EDL but then everytime I get into TWRP (3.2.1.8 Nfound version) it doesn't show up any recovery page just blank after 2 times red led blinks. I have tried 3.2.1.6 version but it was just the same.
The only twrp that works to the recovery page is the official version 3.2.1.0 but you know it doesnt work with oreo build, internal memory encrypted.
YoungAll said:
Anyone succeed flashing TWRP for this build? I flashed this update through EDL but then everytime I get into TWRP (3.2.1.8 Nfound version) it doesn't show up any recovery page just blank after 2 times red led blinks. I have tried 3.2.1.6 version but it was just the same.
The only twrp that works to the recovery page is the official version 3.2.1.0 but you know it doesnt work with oreo build, internal memory encrypted.
Click to expand...
Click to collapse
Guess it is workig ... with twrp 3.2.1.8 Oreo by NFound.
1. Flash EDL image A2017G1.3_B03 (don't choose reboot option |choose N|)
2. Download & copy A2017-TWRPrecovery-3.2.1-0.img to path EDL_install_path\flash\recovery\ (dont forget rename to "recovery.img")
3. Put to your sdcard
a). ZTE_A2017X_V1.3.0B01_OREO_BootStack_twrp3126_by_raystef66.zip by raystef66
b). TWRP_3.2.1-8_axon7-Oreo.img by NFound
c). A2017G_O_system_permission_enable.zip
4. Reboot go to recovery (should be blue teamwin one 3.2.1-0)
5. Install ZTE_A2017X_V1.3.0B01_OREO_BootStack_twrp3126_by_raystef66.zip, TWRP_3.2.1-8_axon7-Oreo.img (as Recovery), A2017G_O_system_permission_enable.zip (a,b,c from step 4)
6. Reboot (second time was sucesfully boot)
7. If you will be faced with some Decrypt Password, dont forget to Fromat Data in Wipe option. (Mandatory step to sucessful boot)
That steps worked for me currently i'm looking for magisk 18 enabling option. I will update this post once succeed.
Not working:
Wifi
nays_pl said:
Guess it is workig ... with twrp 3.2.1.8 Oreo by NFound.
1. Flash EDL image A2017G1.3_B03 (don't choose reboot option |choose N|)
2. Download & copy A2017-TWRPrecovery-3.2.1-0.img to path EDL_install_path\flash\recovery\ (dont forget rename to "recovery.img")
3. Put to your sdcard
a). ZTE_A2017X_V1.3.0B01_OREO_BootStack_twrp3126_by_raystef66.zip by raystef66
b). TWRP_3.2.1-8_axon7-Oreo.img by NFound
c). A2017G_O_system_permission_enable.zip
4. Reboot go to recovery (should be blue teamwin one 3.2.1-0)
5. Install ZTE_A2017X_V1.3.0B01_OREO_BootStack_twrp3126_by_raystef66.zip, TWRP_3.2.1-8_axon7-Oreo.img (as Recovery), A2017G_O_system_permission_enable.zip (a,b,c from step 4)
6. Reboot (second time was sucesfully boot)
7. If you will be faced with some Decrypt Password, dont forget to Fromat Data in Wipe option. (Mandatory step to sucessful boot)
That steps worked for me currently i'm looking for magisk 18 enabling option. I will update this post once succeed.
Not working:
Wifi
Click to expand...
Click to collapse
Wifi not working after all those steps or after you tried magisk 18?
nays_pl said:
Guess it is workig ... with twrp 3.2.1.8 Oreo by NFound.
1. Flash EDL image A2017G1.3_B03 (don't choose reboot option |choose N|)
2. Download & copy A2017-TWRPrecovery-3.2.1-0.img to path EDL_install_path\flash\recovery\ (dont forget rename to "recovery.img")
3. Put to your sdcard
a). ZTE_A2017X_V1.3.0B01_OREO_BootStack_twrp3126_by_raystef66.zip by raystef66
b). TWRP_3.2.1-8_axon7-Oreo.img by NFound
c). A2017G_O_system_permission_enable.zip
4. Reboot go to recovery (should be blue teamwin one 3.2.1-0)
5. Install ZTE_A2017X_V1.3.0B01_OREO_BootStack_twrp3126_by_raystef66.zip, TWRP_3.2.1-8_axon7-Oreo.img (as Recovery), A2017G_O_system_permission_enable.zip (a,b,c from step 4)
6. Reboot (second time was sucesfully boot)
7. If you will be faced with some Decrypt Password, dont forget to Fromat Data in Wipe option. (Mandatory step to sucessful boot)
That steps worked for me currently i'm looking for magisk 18 enabling option. I will update this post once succeed.
Not working:
Wifi
Click to expand...
Click to collapse
you need to flash twrp treble from Nfound or official oreo from nfound trough edl.Done

Categories

Resources