had to replace my glass and digitizer, so i did. after i put my phone all back together i get this weird kind of issue with my lcd. when i startup the phone it looks just fine, but then its like a shade is pulled down most of the screen. it will change depending on the background. just sucks when the main issue is fixed, something else goes wrong. anyone have this problem or know how to fix it shoot me a line.
thanks
Snickles
i tried to post pics but i am a noob and it wont let me. sorry
nevermind about not getting pictures. here they are.
Try reseating the display cable.
i had taken it all apart and back together again, and its still the same.
Did you try the old display? If the old one works, and this one doesn't, then this one is faulty.
it is the old display. it worked perfectly up until i replaced the glass and digitizer. even while my screen was cracked, i could use and see the phone just fine.
How did you get the glued down digitizer off? Did you start prying?
Oh, and you should have gotten an LCD/Digitizer combo.
i got it off by heating the edges carefully with a blowdryer and used the plastic guitar pick tool to remove the glass/digitizer from the lcd. it came off way smooth and easy.
i was thinking to myself i should have got the combo as well, but didn't have the extra 100$ now i totally regret not getting it. FACE PALM!!!
snicklefrits said:
i got it off by heating the edges carefully with a blowdryer and used the plastic guitar pick tool to remove the glass/digitizer from the lcd. it came off way smooth and easy.
i was thinking to myself i should have got the combo as well, but didn't have the extra 100$ now i totally regret not getting it. FACE PALM!!!
Click to expand...
Click to collapse
I looked again. You (somehow) broke the LCD. Look in the second photo at the top in the middle. See the dark spot?
If there is no physical damage, send it into HTC. You still might be under warranty.
mayurolla said:
If there is no physical damage, send it into HTC. You still might be under warranty.
Click to expand...
Click to collapse
He opened the phone.
rr5678 said:
He opened the phone.
Click to expand...
Click to collapse
That doesn't mean there is any visible physical damage. If he carefully replaced any void stickers, he should be fine.
rr5678 said:
I looked again. You (somehow) broke the LCD. Look in the second photo at the top in the middle. See the dark spot?
Click to expand...
Click to collapse
that dark spot it just a piece of tape that is holding the generic screen protector on.
there is no more void sticker, and i purchased it from someone quite a while ago, not through a mobile service.
Just noticed a crack on the back of my camera going across, the plastic/glass part. How can I fix it? Can I just take it off and put on a new one? Do they sell those online anywhere?
chmura said:
Just noticed a crack on the back of my camera going across, the plastic/glass part. How can I fix it? Can I just take it off and put on a new one? Do they sell those online anywhere?
Click to expand...
Click to collapse
if you mean the part with camera glass then it isn't that hard to replace but if back cover is also damaged then you will also need g2 back cover and using a video like g2 screnn replacement but you only need about the first 5 minutes which is about removing the back
XxZombiePikachu said:
if you mean the part with camera glass then it isn't that hard to replace but if back cover is also damaged then you will also need g2 back cover and using a video like g2 screnn replacement but you only need about the first 5 minutes which is about removing the back
Click to expand...
Click to collapse
Thank you for the link, it is the glass. Is there no easier way? Only the glass needs to be replaced. http://i.imgur.com/2yu1zmH.jpg
chmura said:
Thank you for the link, it is the glass. Is there no easier way? Only the glass needs to be replaced. http://i.imgur.com/2yu1zmH.jpg
Click to expand...
Click to collapse
well it isn't that hard all you have to is remove some screws switch the part and place the screws back, but I don't think there is any other way
Hi All
Picked up a Nexus 4 a few days ago and only just noticed (as result of a call) that the proximity sensor is reporting that its "blocked" at all times, so the phone things its against my head. I can workaround this by using the "Power button to hang Up" option but at present cannot access any in call features.
When I look under good light the sensor, there are 2 areas so not sure which is the sensor, I can see what looks like a bubble under both. if you imagine what an air pocket looks like under a screen protector thats what it looks like but its behind the glass, perfectly centred. I guess its possible that something has broken here as a result of the drop, the top left corner was the point of impact, does that seem likely?
I got the phone cheap as it had a broke screen so have a new one coming. Its the full screen, glass and digitizer. Does anyone know of the sensor is part of the screen or does it sit behind and then I could be really screwed!
Ta
bert682 said:
Hi All
Picked up a Nexus 4 a few days ago and only just noticed (as result of a call) that the proximity sensor is reporting that its "blocked" at all times, so the phone things its against my head. I can workaround this by using the "Power button to hang Up" option but at present cannot access any in call features.
When I look under good light the sensor, there are 2 areas so not sure which is the sensor, I can see what looks like a bubble under both. if you imagine what an air pocket looks like under a screen protector thats what it looks like but its behind the glass, perfectly centred. I guess its possible that something has broken here as a result of the drop, the top left corner was the point of impact, does that seem likely?
I got the phone cheap as it had a broke screen so have a new one coming. Its the full screen, glass and digitizer. Does anyone know of the sensor is part of the screen or does it sit behind and then I could be really screwed!
Ta
Click to expand...
Click to collapse
Ok so I did a little more reading and it seems that a gorilla has changed the screen on this phone in the past and he / she has used compound to stick the screen down and some of it has gone around the sensor and the resulting press down on the screen has created a few air pockets.
Looking less forward to changing the screen now as no doubt with my luck the "technician" will have used some crazy heat resistant glue!
Also....missing the speaker grille....funny how you only notice things after you have bought them!
Search for proximity sensor fix after screen replacement here on xda. I've found out that if you switch sides of the little rubber /plastic cover that covers the proximity sensor, your problem will be solved. And the light sensor will work with no problems as well.
Sent from my Nexus 4 using Tapatalk
Sp_Ark said:
Search for proximity sensor fix after screen replacement here on xda. I've found out that if you switch sides of the little rubber /plastic cover that covers the proximity sensor, your problem will be solved. And the light sensor will work with no problems as well.
Sent from my Nexus 4 using Tapatalk
Click to expand...
Click to collapse
Really?
From reading the thing to do is either make the height of the bushing a little larger, height wise. Or, to increase the diameter of the holes.
I like your fix the best though....no messing about, just rotate.
Will give it a go, thanks!
It will work for sure, I posted this fix on a YouTube screen replacement guide of octopus glues I think and its confirmed to work from a lot of people. Then if you use a custom rom go to brightness settings while having auto brightness enabled and try changing light sources from dark to very bright places to see the instant lux values you get. If you are not satisfied with the result try custom auto brightness values.
Sent from my Nexus 4 using Tapatalk
bert682 said:
Really?
From reading the thing to do is either make the height of the bushing a little larger, height wise. Or, to increase the diameter of the holes.
I like your fix the best though....no messing about, just rotate.
Will give it a go, thanks!
Click to expand...
Click to collapse
Yep, I discovered this "fix" in a random youtube comment (was that you @Sp_Ark?) just a few days ago, and it worked for me. Then I found a thread here that confirmed that this could be a solution (which could have saved me a week of frustration).
If there's actually something on the proximity sensor, then you might be screwed. Well, not really, or $10 from China. The module is a snap-in piece with connector ribbon that also has the headphone jack. The prox sensor is the smaller one on the right side (when looking at the screen).
Disassembly of the Nexus 4 is pretty simple compared to many other smartphones. You'll need a T5 TORX wrench/bit for the screws at the bottom, and a very small Phillips driver for all the screws in the inside. You'll also need a tool to split the 2 halves apart (your screen replacement might have come with tools). You can find a couple videos on youtube, as well as a detailed teardown (pics) at ifixit.com. If you have a hairdryer (or an actual heat gun) you can make the process easier by softening the glue with heat, but it's not absolutely necessary. Just go slowly and be careful when prying the halves apart so you don't flex it too much and break the glass back.
Which screen assembly did you get? You can get it where it's just the LCD and the digitizer, and you can also get it that has the bezel and speaker with it. When I replaced the screen on my N4, I got the whole deal with the bezel and speaker, since it meant less work and fewer things to screw up.
Planterz said:
Yep, I discovered this "fix" in a random youtube comment (was that you @Sp_Ark?) just a few days ago, and it worked for me. Then I found a thread here that confirmed that this could be a solution (which could have saved me a week of frustration).
If there's actually something on the proximity sensor, then you might be screwed. Well, not really, or $10 from China. The module is a snap-in piece with connector ribbon that also has the headphone jack. The prox sensor is the smaller one on the right side (when looking at the screen).
Disassembly of the Nexus 4 is pretty simple compared to many other smartphones. You'll need a T5 TORX wrench/bit for the screws at the bottom, and a very small Phillips driver for all the screws in the inside. You'll also need a tool to split the 2 halves apart (your screen replacement might have come with tools). You can find a couple videos on youtube, as well as a detailed teardown (pics) at ifixit.com. If you have a hairdryer (or an actual heat gun) you can make the process easier by softening the glue with heat, but it's not absolutely necessary. Just go slowly and be careful when prying the halves apart so you don't flex it too much and break the glass back.
Which screen assembly did you get? You can get it where it's just the LCD and the digitizer, and you can also get it that has the bezel and speaker with it. When I replaced the screen on my N4, I got the whole deal with the bezel and speaker, since it meant less work and fewer things to screw up.
Click to expand...
Click to collapse
I got a "kit" off eBay, [URL="http://www.ebay.co.uk/itm/181144377215?_trksid=p2059210.m2749.l2649&ssPageName=STRK%3AMEBIDX%3AIT"]http://www.ebay.co.uk/itm/181144377215?_trksid=p2059210.m2749.l2649&ssPageName=STRK%3AMEBIDX%3AIT so it appears to be the complete screen. Ive watched a few videos but from the pictures it looks like the screen comes with the metal backing so I suspect I dont need to remove the old screen from the casing, thoughts?
Im expecting this to be the screen, bezel, and metal backing so I need to do is connect in my motherboard and all the other components.
Am I off in thinking this?
That's the full part. The one you've posted is the type I usually go for, they're good quality so far.
bert682 said:
I got a "kit" off eBay, http://www.ebay.co.uk/itm/181144377215?_trksid=p2059210.m2749.l2649&ssPageName=STRK%3AMEBIDX%3AIT so it appears to be the complete screen. Ive watched a few videos but from the pictures it looks like the screen comes with the metal backing so I suspect I dont need to remove the old screen from the casing, thoughts?
Im expecting this to be the screen, bezel, and metal backing so I need to do is connect in my motherboard and all the other components.
Am I off in thinking this?
Click to expand...
Click to collapse
You made a wise choice, young padawan.
Yeah, that looks to be the entire front assembly, including the screen+digitizer, already installed in the bezel. Also includes the earpiece plus the speaker grill that you're missing. You'll have to swap over the guts, and that's about it. It's easiest to swap the power and volume rocker buttons first since it's a bit harder to get them where they go if you've got the logic board in the way. Just remember that the contact points need to make a ^ rather than a v when you're assembling it with the screen facing down. Tweezers are good to have, especially if they're very long and even better if they're curved. I also recommend doing this over a clean towel to avoid scratching the screen (there'll probably be a film over it too), and the fluffier the towel the better, to catch the tiny screws from flying and disappearing.
Honestly, getting the 2 halves apart is probably the hardest part. They make specialized tools for this, and often the sellers will include them, but it doesn't look like your purchase includes them (mine didn't either). Something plastic is the best choice, since you're less likely to cause cosmetic damage to the plastic (especially the bezel) if you slip (and you will slip). As I said before, GO SLOWLY. Work it apart a little bit at a time, alternate side to side, starting from the bottom. Eventually you'll be able to pull the 2 halves apart.
The battery will be stuck in pretty good and will need to be pried out. If I were you (and a week or so ago, I was you), I'd pop a new battery in while you're at it. At this point in the phone's life, it's probably had at least a few hundred cycles on the battery and has lost 10-20% of its original capacity. The other components shouldn't be nearly as hard to get out. Just pry in various points until the piece pops out. Do not force anything. Just work it out slowly. After you pop off the piece that covers the USB port, there's the board that has the port, and that can be slightly tricky to get out. Best way I found is to slip something small and flat (screwdriver?) into the port and push up and out, and the board should come out easily.
Thankfully, there's only 3 different screws used, and they're all easily differentiated from each other. There's the 2 T5 TORX that hold the halves together, the 2 very short screws with wide heads that hold the battery in place, and the rest that hold everything else are all identical to each other.
It looks like on your assembly, it comes with its own adhesives. Everywhere there's a blue film, pull it off and there'll be adhesive underneath. I'd recommend leaving the film on over the part where the sensor/headphone jack module goes until you're sure you can stick it in place with the proximity sensor not acting wonky. Download an app (I used Phone Tester) that can read the prox sensor. FYI, as long as everything is in place, and you've attached the battery, you can boot the phone without replacing the back cover, and test the sensor (just depress the center bit of the power button board). You don't need to screw everything in, but you should at least screw and tighten down the few that surround the sensor area. Once you've got it reading properly (best of luck), it's time to put all back together.
You should familiarize yourself with the teardown/reassembly guides out there. Go to ifixit.com and have everything ready to look at. This is the video that I used to guide me, and I watched it through a few times before I attempted it myself. You should be just fine with your phone after familiarizing yourself, but if you have any specific problems or questions, feel free to ask, and I'm all too happy to help.
Planterz said:
You made a wise choice, young padawan.
Yeah, that looks to be the entire front assembly, including the screen+digitizer, already installed in the bezel. Also includes the earpiece plus the speaker grill that you're missing. You'll have to swap over the guts, and that's about it. It's easiest to swap the power and volume rocker buttons first since it's a bit harder to get them where they go if you've got the logic board in the way. Just remember that the contact points need to make a ^ rather than a v when you're assembling it with the screen facing down. Tweezers are good to have, especially if they're very long and even better if they're curved. I also recommend doing this over a clean towel to avoid scratching the screen (there'll probably be a film over it too), and the fluffier the towel the better, to catch the tiny screws from flying and disappearing.
Honestly, getting the 2 halves apart is probably the hardest part. They make specialized tools for this, and often the sellers will include them, but it doesn't look like your purchase includes them (mine didn't either). Something plastic is the best choice, since you're less likely to cause cosmetic damage to the plastic (especially the bezel) if you slip (and you will slip). As I said before, GO SLOWLY. Work it apart a little bit at a time, alternate side to side, starting from the bottom. Eventually you'll be able to pull the 2 halves apart.
The battery will be stuck in pretty good and will need to be pried out. If I were you (and a week or so ago, I was you, I'd pop a new battery in while you're at it. At this point in the phone's life, it's probably had at least a few hundred cycles on the battery and has lost 10-20% of its original capacity. The other comments shouldn't be nearly as hard to get out. Just pry in various points until the piece pops out. Do not force anything. Just work it out slowly. After you pop off the piece that covers the USB port, there's the board that has the port, and that can be slightly tricky to get out. Best way I found is to slip something small and flat (screwdriver?) into the port and push up and out, and the board should come out easily.
Thankfully, there's only 3 different screws used, and they're all easily differentiated from each other. There's the 2 T5 TORX that hold the halves together, the 2 very short screws with wide heads that hold the battery in place, and the rest that hold everything else are all identical to each other.
It looks like on your assembly, it comes with its own adhesives. Everywhere there's a blue film, pull it off and there'll be adhesive underneath. I'd recommend leaving the film on over the part where the sensor/headphone jack module goes until you're sure you can stick it in place with the proximity sensor not acting wonky. Download an app (I used Phone Tester) that can read the prox sensor. FYI, as long as everything is in place, and you've attached the battery, you can boot the phone without replacing the back cover, and test the sensor (just depress the center bit of the power button board). You don't need to screw everything in, but you should at least screw and tighten down the few that surround the sensor area. Once you've got it reading properly (best of luck), it's time to put all back together.
You should familiarize yourself with the teardown/reassembly guides out there. Go to ifixit.com and have everything ready to look at. This is the video[/i] that I used to guide me, and I watched it through a few times before I attempted it myself. You should be just fine with your phone after familiarizing yourself, but if you have any specific problems or questions, feel free to ask, and I'm all too happy to help.
Click to expand...
Click to collapse
Awesome, I saw some cheaper screens but that one notes that its LG compliant etc. I bought a set of tools separately so will have all the stuff needed. Didnt think about the battery, will order one as it does make sense!
Thanks for the info, will update as I go.
If you want to have a working battery like it used to be before removing it, you have to be very patient and extra careful while trying to remove it. Use some heat for the glue and try with something very thin like a nylon guitar pick. In anyway don't bent the battery and don't start from top. It will be easier to first remove the mother board. Iv already destroyed 4 5 batteries while trying to remove them. Sorry for my English, I hope you understand.
Sent from my Nexus 4 using Tapatalk
Sp_Ark said:
If you want to have a working battery like it used to be before removing it, you have to be very patient and extra careful while trying to remove it. Use some heat for the glue and try with something very thin like a nylon guitar pick. In anyway don't bent the battery and don't start from top. It will be easier to first remove the mother board. Iv already destroyed 4 5 batteries while trying to remove them. Sorry for my English, I hope you understand.
Sent from my Nexus 4 using Tapatalk
Click to expand...
Click to collapse
Yea was extra careful, used a little heat. Someone has definately replaced the screen on the phone before but seems to have been careful enough as no screws missing etc, except the lost the little speaker grille
New screen in and working well. The proximity sensor seems to be working but it reports all or nothing rather than varied. Is this correct?
bert682 said:
Yea was extra careful, used a little heat. Someone has definately replaced the screen on the phone before but seems to have been careful enough as no screws missing etc, except the lost the little speaker grille
New screen in and working well. The proximity sensor seems to be working but it reports all or nothing rather than varied. Is this correct?
Click to expand...
Click to collapse
Yeah this is normal.
Sent from my Nexus 4 using Tapatalk
bert682 said:
New screen in and working well.
Click to expand...
Click to collapse
Awesome! See, it wasn't too bad, was it? Ifixit gives the N4 a 7/10 for repairability, and that's pretty high for them. After replacing my N4 screen, friend/coworker asked if I could do the same for his HTC One M7 with a completely shattered, yet functional digitizer. I said "HEEEEEEEEEEELL NO!"
Planterz said:
Awesome! See, it wasn't too bad, was it? Ifixit gives the N4 a 7/10 for repairability, and that's pretty high for them. After replacing my N4 screen, friend/coworker asked if I could do the same for his HTC One M7 with a completely shattered, yet functional digitizer. I said "HEEEEEEEEEEELL NO!"
Click to expand...
Click to collapse
No, not with the correct tools. I will admit had I not bought the plastic tools, tweezers etc I may have struggled.
The battery was my main concern, its really stuck down, even though this had been replaced before and likely a less tacky glue used it was still tough. Had to use some heat to soften it and the "battery cover" has seen better days. Next thing to replace is that, just for piece of mind.
All in all, pretty nice experience, the phone seems more modular that other phones I have taken apart which is nice.
Dear xda,
while being on holiday in South-East Asia, I got into some pretty heavy rain and my OnePlus 2 obviously didn't like the rain - the display seems to be broken since. Unfortunately I tried switching the phone on shortly after the water contact (because I needed it for navigation) and the display worked just fine while the phone seemed to be stuck software-wise (although now from a retrospective point of view it could have been that already then the display was somehow having issues).
I did put it in dry, uncooked rice just a few hours after the water contact and kept it there for a few days, with the SIM-Tray ejected and the back cover taken off. Still, after a few days, I tried switching it on again and I could notice that is was booting up just fine (I could see the capacitative buttons lighting up and even got some notification sounds after it booted up), but the display remained black
Back home I removed not only the SIM-Tray and the back cover but also the "inside cover" as well as the battery (it then looked like THIS) and put the phone back into rice for another 2 days. After that I reassambled the phone and tried switching it on again - still the display wasn't working.
After disassembling the phone again and taking the battery out, I put the remaining parts of the phone into the oven at about 45°C = 113°F for about 2h. But that didn't help either.
Is there any advice as how to maybe get my display working again? Maybe some cable or connection inside the phone that I could inspect or disconnect and reconnect? The process of buying a display on eBay and replacing the display seems to be rather complicated (due to the fact that the display is glued to the frame as from what I could see on ifixit.com) and I don't want to damage more than I already did while maybe the repair attempt doesn't help at all.
Does anyone have any experience/insight regarding how much it would cost me to open a repair ticket with OnePlus and let them repair/replace my display unit?
Guess it would cost around 200USD since the display is one of the costliest components in the phone. Not sure if it's only the display issue though. The water might have done some serious damage to the board itself.
100$ easily
My replacement screen cost me 30$ including shipping to Sweden, bought on Aliexpress, top notch quality nothing to complain on quality wise .
Skickat från min ONE A2003 via Tapatalk
pitrus- said:
My replacement screen cost me 30$ including shipping to Sweden, bought on Aliexpress, top notch quality nothing to complain on quality wise .
Skickat från min ONE A2003 via Tapatalk
Click to expand...
Click to collapse
I too considered buying a replacement screen on ebay or aliexpress. But I don't think I feel confident enough to take the necessary steps to replace the screen, because you seem to have to "unglue" the old screen and glue the new screen back on the frame (Sources: https://www.ifixit.com/Guide/OnePlus+2+Screen+Replacement/51922#s115570 and https://youtu.be/Q1b5Ut5kTRM?t=4m).
Is it easier to do than I think? Did you face any issues while replacing it? Can you see or feel a difference with the new screen compared to the original one (i.e. does it perfectly fit into the frame without protruding)?
gnaggwatschn said:
I too considered buying a replacement screen on ebay or aliexpress. But I don't think I feel confident enough to take the necessary steps to replace the screen, because you seem to have to "unglue" the old screen and glue the new screen back on the frame (Sources: https://www.ifixit.com/Guide/OnePlus+2+Screen+Replacement/51922#s115570 and https://youtu.be/Q1b5Ut5kTRM?t=4m).
Is it easier to do than I think? Did you face any issues while replacing it? Can you see or feel a difference with the new screen compared to the original one (i.e. does it perfectly fit into the frame without protruding)?
Click to expand...
Click to collapse
It was pretty straight forward and simple. I just applied heat to screen using a hairdryer and the used the included suction cup to gently loosed the screen from the adhesive using a credit hard to pry away the glue and then removed the connections to the screen and the touch-buttons and home button from the backside and then removed the screen. Then I moved over the home button and touch buttons to the new screen, applied some 3M adhesive strips on the frame after removing the old adhesive, put the screen back in place and reconnected the collectors, pushed the screen in place in the frame and heated it a bit too make sure the adhesive sticks and then screwed everything back in there and put on the back case. Done and done!
Ok I think I am gonny try tro buy a screen on aliexpress and replace it myself. Do you think this one should do?
well maybe you guys can help me out here i did the steps to replace the fingerprint sensor but now my screen wont stay glued , i have not been able to find the glue for the screen anyone can help with that by any chance ?
jera27 said:
well maybe you guys can help me out here i did the steps to replace the fingerprint sensor but now my screen wont stay glued , i have not been able to find the glue for the screen anyone can help with that by any chance ?
Click to expand...
Click to collapse
I would also like to know which kind of "3M adhesive strips" pitrus- used to keep the screen glued.
gnaggwatschn said:
I would also like to know which kind of "3M adhesive strips" pitrus- used to keep the screen glued.
Click to expand...
Click to collapse
I bought this one linked down here
3M Sticker Tape Sticker 1MM Double Side Adhesive For Cellphone Touch Screen LCD
http://s.aliexpress.com/UBbquiQf
(from AliExpress Android)
i will try it thanks how did you apply it ? did you have to do any modifications ? is the phone screen similar to its original state ? did you remove the previous glue ? soo many questions i wish there was a video on how to apply it on the phone , as of now my bottom half of the phone screen is unglued
jera27 said:
i will try it thanks how did you apply it ? did you have to do any modifications ? is the phone screen similar to its original state ? did you remove the previous glue ? soo many questions i wish there was a video on how to apply it on the phone , as of now my bottom half of the phone screen is unglued
Click to expand...
Click to collapse
For me, the old adhesive came off with the old screen. But I did some cleaning with alcohol just to be sure.