Database Users

Dust under the touch screen - solution!!!

Hi to all who have dust between the touch screen digitizer and LCD.
I send my device 3 times to the authorised HTC service center because of this problem, they cleaned it (not perfectly) and the dust was back again after few days of use. This was really ennoying for me...
After several disassemblies, cleaning, research where dust comes in, then assembles I found the flaw.
The dust doesn’t come in via sealing foam between the touch screen digitizer and LCD.
There is a bump defect of phone housing around the volume keys. Inside of the plastic housing is a metal frame, where the touch screen digitizer is stacked on - that frame is a little bended and the touch screen doesn’t stick properly on it (around the volume keys only). When you look close on the phone you can see also a little wider gap between the touch screen top glass and silver plastic housing edge. (See picture)
WARNING
The following directions WILL VOID
your warranty - you are performing
this repair at your own risk.
So, now, what you have to do:
For those, who have already dust in, just simply disassembly your device (if you are brave enough, have all tools and precise hands - maybe some experience ) and remove PROPERLY all dirt with brush, compressed air and antistatic cloth, then assemble it back or send the device to the service center to clean it (wont void the warranty). Before sealing your TD2 (keep it in plastic bag away from dust) prepare a sharp wooden toothpick, neutral transparent or black silicone (you can purchase it from any building material shop) and cotton cloth.
Now you have to clean the gap between whole plastic silver housing frame and touch screen top glass with soft brush. Then use sharp wooden toothpick to impress the silicone into the gap (all gaps you can see, just in case) (silicone does not damage phone housing and TSCR surface and it’s easy to clean), then just gently and properly wipe off all the rest of silicone from phone surface. (be careful not to get silicone to the keys or phone receiver slot)
Leave the phone for several hours to get silicone dry.
Then you can use your TD2 in dusty environment and your display stays absolutely clean and dusty free. (TESTED on mine, for me perfect phone now and I am very happy with it...)
For those who have a little dust in and want to stop come more in and those who are planning to buy TD2 (dont wanna play the lottery faulty or not ), do the same procedure (silicone impress only) after unwrapping your device from plastic package.
GOOD LUCK!!! ENJOY YOUR ABSOLUTELY DUSTY FREE DEVICE!!!
Sorry for my English

I don't know about you guys, but I'm not crazy enough to void the warranty of my phone because of a minor thing like that. When mine gets dirty, I send it back and that's it.
If it gets dirty again, I send it back again...
But, it's a good tutorial for the "brave ones" anyway Thanks for sharing your experience with us.
HastaSSSS

I sent mine back over a week ago due to this dust problem (in fact I delivered it in person to HTC repair center in Milton Keynes) hoping for a quick turnaround.
I'm still waiting for it to come back and missing it terribly. I'm back to using my old Nokia E71 which is a great phone but I like my new one and want it back so I may go down the route of the OP just so I don't have to repeat the return each time I get a dust issue.....

http://forum.xda-developers.com/showthread.php?t=519463
i dont want to hijack this thread. if i am then i am sorry
but hopefully you can input your expertise into this thread or help form an opinion for a new thread

I just got a topaz and want to keep dust from getting in but I'm confused about the sillicon. Could you describe more clearly what it is and maybe post a picture so I have some idea what it should look like.

from the picture, for the second gap, apply the protective foil that comes with the phone. Should solve a bit the problem. Ber in mind that after apply, the touchscreen will not have the same sensitivity. You'll have to tap a little bit harder ...

i think you meant screen protector no?
anyway thx for the info,
if anyone knows how to disassemble this device pls help

yes, screen protector. Better not use the screwdriver ... remember warranty ...

I thought these dust under the screen issues had been fixed long ago, but now it seems the problem that affected my old c600 has come back to ruin my topaz after just 1 week.
Not impressed.

georgeono said:
from the picture, for the second gap, apply the protective foil that comes with the phone. Should solve a bit the problem. Ber in mind that after apply, the touchscreen will not have the same sensitivity. You'll have to tap a little bit harder ...
Click to expand...
Click to collapse
I already use a screen protector. I'm more concerned about the first gap. I really don't want dust to happen since I bought my phone second hand and it doesn't have a warrenty.

you can always use a can of pressurized air to get the dust out. (same you use with PCs)

Wouldn't you need two holes that are connected if your blowing air into the device? One for the air to go in and one for the dust to go out? I don't have any dust under my screen currently and would like it to remain that way. The silicon method doesn't seem to difficult or dangerous which is why I'm interested in what silicon to use.

from what I understood (from the pictures in the 1st post), it's not actually a hole, but a free space = gap.

I opened the D2 (only the two upper screws - for lifting the inner part a bit) and did have a look for "gaps" somewhere around the volume controls - i did not really see a gap
But for getting out the dust: dont blow air into the D2 but get the air out - i actually used a vacuum-cleaner. If you remove the two screws it is possible to lift the LCD below the volume sliders *A LITTLE BIT* (=about 0,5 mm only!!!!!) with a small screw driver to create a gap. It worked quite well. (be aware of high air flow and possible static electricity)
But i really would like to know, where exactly to apply some supplementary sealing to get rid of the dust-problem. Any detailed pic would be appreciated.

axantas said:
But i really would like to know, where exactly to apply some supplementary sealing to get rid of the dust-problem. Any detailed pic would be appreciated.
Click to expand...
Click to collapse
Yeah Me too!

OK, people, just put some neutral silicone between (in the gap) silver plastic frame and touch screen (there is just 0,2 -0,5 mm gap, almost invisible) and you wont get any dust under the touch screen. This is the best solution, you could do it from inside, but its much more complicated...

pedroo said:
OK, people, just put some neutral silicone between (in the gap) silver plastic frame and touch screen (there is just 0,2 -0,5 mm gap, almost invisible) and you wont get any dust under the touch screen. This is the best solution, you could do it from inside, but its much more complicated...
Click to expand...
Click to collapse
What exactly is neutral silicone? Do you have a picture of it so I know what to buy?

I'm about to buy the TD2,
is it so big problem this dust under the screen?
Does it happen often?

luca T said:
I'm about to buy the TD2,
is it so big problem this dust under the screen?
Does it happen often?
Click to expand...
Click to collapse
I've had it for about a week and the user I bought it from had it supposedly for about 3 weeks and so far no dust. I'm still terrified its going to happen though.

pedroo said:
OK, people, just put some neutral silicone between (in the gap) silver plastic frame and touch screen (there is just 0,2 -0,5 mm gap, almost invisible) and you wont get any dust under the touch screen. This is the best solution, you could do it from inside, but its much more complicated...
Click to expand...
Click to collapse
Thanks for the pic, pedroo - so they simply should have glued the digitizer surface a bit more careful to the housing...
...thinking a bit about applying the radical solution - not sure yet

Finally fixed by Touch HD!!

To make a long story short:
I must have somehow put too much pressure on the digitizer to create a "newton ring" which in turn would not allow me to use the touch feature of the digitizer. I sent it to HTC USA to repair it. They noticed the "newton ring" as well as the modified ROM
They would not warranty the "newton ring" and said they would not repair the Digitizer due to the fact that it had been "hacked". They would replace the Digitizer, LCD and internals for $389.00. I told them they were smoking crack.
After paying HTC $25.00 for doing nothing they sent the phone back and I went online to order a Digitizer. I paid $17.00 which included shipping and I got it within 7 days.
The HTC service manual does not have a guide on how to replace the digitizer or the LCD. They really don't want you messing with it.
It was scary and I thought I had ruined the phone when I pryed the front of the unit open. At first the sticker to the digitizer came off(black framing) and then you have to pry the digitizer(its pretty stiff) from the frame. I destroyed the thin cable that led to the backside of the LCD but the new one has one already attached so I wasn't worried about that part. The LCD with a metal base plate is attached to the back of it. You have to slowly pry off the LCD from the backside of the digitizer.
Anyways I have assembled it back and everything is working perfectly. It was doing Micro-Surgery at times.
Just wanted to share my story.

Congratulations!!

mrmomoman said:
To make a long story short:
I must have somehow put too much pressure on the digitizer to create a "newton ring" which in turn would not allow me to use the touch feature of the digitizer. I sent it to HTC USA to repair it. They noticed the "newton ring" as well as the modified ROM
They would not warranty the "newton ring" and said they would not repair the Digitizer due to the fact that it had been "hacked". They would replace the Digitizer, LCD and internals for $389.00. I told them they were smoking crack.
After paying HTC $25.00 for doing nothing they sent the phone back and I went online to order a Digitizer. I paid $17.00 which included shipping and I got it within 7 days.
The HTC service manual does not have a guide on how to replace the digitizer or the LCD. They really don't want you messing with it.
It was scary and I thought I had ruined the phone when I pryed the front of the unit open. At first the sticker to the digitizer came off(black framing) and then you have to pry the digitizer(its pretty stiff) from the frame. I destroyed the thin cable that led to the backside of the LCD but the new one has one already attached so I wasn't worried about that part. The LCD with a metal base plate is attached to the back of it. You have to slowly pry off the LCD from the backside of the digitizer.
Anyways I have assembled it back and everything is working perfectly. It was doing Micro-Surgery at times.
Just wanted to share my story.
Click to expand...
Click to collapse
How did you attach the digitizer to the LCD? Aren't they glued together or something like that?
Because that's where my attempt went terribly wrong: Instead of getting the digitizer off my LCD, I broke my LCD... I bought a new complete screen unit because I didn't know how the LCD is attached to the digitizer!

The digitizer is semi-glued to the LCD panel which sits on the back along with the thin metal cover. The digitizer has a thin flat connector that connects to the back of the main board on the bottom. I slowly pryed off the LCD(grayish white in color) from the back of the Digitizer. It came off and I aligned it back up with the new digitizer and the glue residue left over from the LCD adhered to the rear of the new Digitizer. the tricky part is the thin connectors that attach to the mainboard. You have to get a pair of tweezers to pull it from the flat connector. When you get the digitizer you will see the new connector. Attaching that and the prying of the LCD was the hard part.
I read somewhere some guy said he broke the LCD but in truth it wasn't the LCD that he broke. He pryed apart the 3 layers of the Digitizer and thought he ruined the LCD. I thought the same thing orignally then I when the whole LCD/Digitizer was in my hand I was looking realized that the LCD was the grayish/white panel on the back. One can easily peel away the top 2 layers of the digitizer and would think that it could be the LCD they ruined.
I hope that makes sense. It was the first time I did this and I didn't see the video where someone removed the Screen. I only saw the Russian guy who didn't finish the job because he was stuck at the end. I just figured it out the hard way.
Also the T6 works but I think a t5 would be better. I only had a T6 and it did the job.
I am so glad I wore gloves or I would have had some major finger prints all over the unit

mrmomoman said:
The digitizer is semi-glued to the LCD panel which sits on the back along with the thin metal cover. The digitizer has a thin flat connector that connects to the back of the main board on the bottom. I slowly pryed off the LCD(grayish white in color) from the back of the Digitizer. It came off and I aligned it back up with the new digitizer and the glue residue left over from the LCD adhered to the rear of the new Digitizer. the tricky part is the thin connectors that attach to the mainboard. You have to get a pair of tweezers to pull it from the flat connector. When you get the digitizer you will see the new connector. Attaching that and the prying of the LCD was the hard part.
I read somewhere some guy said he broke the LCD but in truth it wasn't the LCD that he broke. He pryed apart the 3 layers of the Digitizer and thought he ruined the LCD. I thought the same thing orignally then I when the whole LCD/Digitizer was in my hand I was looking realized that the LCD was the grayish/white panel on the back. One can easily peel away the top 2 layers of the digitizer and would think that it could be the LCD they ruined.
I hope that makes sense. It was the first time I did this and I didn't see the video where someone removed the Screen. I only saw the Russian guy who didn't finish the job because he was stuck at the end. I just figured it out the hard way.
Also the T6 works but I think a t5 would be better. I only had a T6 and it did the job.
I am so glad I wore gloves or I would have had some major finger prints all over the unit
Click to expand...
Click to collapse
Thank you for your explanation! But I'm still not going to attempt this on my own any time soon... We'll see... Maybe I'll change my mind if my digitizer is broken or scratched...

Respect man! You mentioned that you bought digitizer for $17. Is it possible to buy mainboard for Touch HD from that place? Can you please advise where I can get it. And how much it will be?

Got to love a bit of micro-electronics DIY!

This just shows that HTC are taking people for a ride - there are a lot of people who would have just paid the price they stated. As you've only replaced the digitizer, shows they were taking the mick with the LCD and otherwise, what are these "internals" that HTC said it needed I wonder...??

Just replaced the digitizer on my HD and it took about 1.5hrs. As long as you're very careful, it's not that hard at all.
Make sure you have the Service Manual though as it was a great help.

Have you got the link for the service manual?
Ive just had to order a Digitizer as my phone has decided it doesnt want to work anymore (6 months to go on contract too ffs).
Managed to get one from a UK seller with tools for £17 so im happy.

KickAssMoves said:
Have you got the link for the service manual?
Click to expand...
Click to collapse
It's in the wiki.

WelshWarior said:
Just replaced the digitizer on my HD and it took about 1.5hrs. As long as you're very careful, it's not that hard at all.
Make sure you have the Service Manual though as it was a great help.
Click to expand...
Click to collapse
Hi:
How did you get the digitizer separated from the LCD?
I was thinking of putting two suction cups (1 on the back of the LCD, and the other on the front of the digitizer), heating everything up for a couple of minutes with a heat gun, and then pulling them apart holding the suction cups.
Does that make sense?
Thanks.

mrmomoman said:
To make a long story short:
I must have somehow put too much pressure on the digitizer to create a "newton ring" which in turn would not allow me to use the touch feature of the digitizer. I sent it to HTC USA to repair it. They noticed the "newton ring" as well as the modified ROM
They would not warranty the "newton ring" and said they would not repair the Digitizer due to the fact that it had been "hacked". They would replace the Digitizer, LCD and internals for $389.00. I told them they were smoking crack.
After paying HTC $25.00 for doing nothing they sent the phone back and I went online to order a Digitizer. I paid $17.00 which included shipping and I got it within 7 days.
The HTC service manual does not have a guide on how to replace the digitizer or the LCD. They really don't want you messing with it.
It was scary and I thought I had ruined the phone when I pryed the front of the unit open. At first the sticker to the digitizer came off(black framing) and then you have to pry the digitizer(its pretty stiff) from the frame. I destroyed the thin cable that led to the backside of the LCD but the new one has one already attached so I wasn't worried about that part. The LCD with a metal base plate is attached to the back of it. You have to slowly pry off the LCD from the backside of the digitizer.
Anyways I have assembled it back and everything is working perfectly. It was doing Micro-Surgery at times.
Just wanted to share my story.
Click to expand...
Click to collapse
i just had mines fixed called them told them wat i did that i found an outer sreen and tryed to replace it myself and completely destroyed the lil black screen inside of the 4screens put together and that my device software was moded now i had 469 out going and another 469 incoming calls they only charged me 113 but wen we first talked about it they did say about 350 until they see the device and then they will call you before the repair it but the did wipe out my device and reinstalled the oem rom they also gave me a full new body and zero'ed out the incoming and out going calls which never changest unless they put in a new mother board which makes my phone brand new

sorry if ive missed it, but how do you get the lcd and digi out from the black outer casing frame to start with ??, from what i can see it comes out by somehow pushing from the inside to make it pop out ?? could someone please explain a little bit more on how to do this, ill try and make a vid of me getting it out as i have yet to find one that shows this, also my screen has that wierd pearl essance look to it?? does this mean its the digitiser.
Cheers
Mike

pickie said:
sorry if ive missed it, but how do you get the lcd and digi out from the black outer casing frame to start with ??, from what i can see it comes out by somehow pushing from the inside to make it pop out ?? could someone please explain a little bit more on how to do this, ill try and make a vid of me getting it out as i have yet to find one that shows this, also my screen has that wierd pearl essance look to it?? does this mean its the digitiser.
Cheers
Mike
Click to expand...
Click to collapse
Mine had that pearl essence look to it for a good few months before it broke, not that im sure that has anything to do with it.
Just awaiting the delivery of the digitizer and hopefully I can repair it.

yeh mine had the pearl effect for a long time prior to it dyeing

ive followed the service manual and the video of the guy who gets stuck near the end, but how do you g et the screen out of the casing to get to the digitizer?
Its one hell of atight fit and i cant see anything o bvious.
Help

Hi Guys
Sorry about the late replies - had phoneline probs!!
Assuming you followed the instructions in the Service Manual to take the rest of the phone apart, you've just gotta be VERY careful and push the screen out from the back (where the Circuit Boards where) of the plastic frame. At first, it feels like it's not budging but be patient and it WILL start to push away.
It seems to be held in with some sort of hot glue or maybe a contact sort of adhesive and I didn't try it but some heat from something like a hair dryer may make the job easier.
Many people have cracked their LCD screen during the repair but as long as you're careful not to bend the screen too much when taking it out, you'll be fine.
I peeled the 3 layers (outer glass ones and then the Digitizer itself) off the LCD whilst removing it.
Good luck - it's really not that hard. Any more questions - just ask ;-)

ive got the phone apart to the point of the service manual/video
which part of the back do you push out? doesnt look obvious as to whats attached and what isnt

Once you get to the last stage (I thinks it's the Speaker Removal) you simply push on the metal protector of the LCD from the back. You will see small holes in the plastic of the back of the frame where you can push something blunt through and push very lightly on the LCD to push it out.
If I remember correctly, at the bottom of the phone where the circuit board with the vibrator and microphone on it was sitting, there is quite a large opening with the metal backing of the LCD visible through it. I started pushing there and gently went all around the phone in the various small holes dotted around it.
As I said above, it won't feel like it's working at first but it will - just be patient and not too heavy handed!

[Q] Water damaged HD2 (advice please)

Last Friday night I had a little accident and my HD2 ended up spending some time in a river... I won't get in to details but the phone's been drying out ever since and I've got a torx T5 screwdriver on the way so I can take it apart if needed. I tried to turn it on earlier today and it actually seems to almost be working perfectly ; I've got sound, vibration, WP7 boots up just fine and the touch screen is as responsive as ever but the one problem I do have is the backlight. I can only see things on the screen in pitch darkness. From what I've read, it looks like I might have to buy a new LCD screen but before ordering parts I'd like to get a few opinions about what I should try to get it working properly again.
Thanks in advance.

NeoGreendawg said:
Last Friday night I had a little accident and my HD2 ended up spending some time in a river... I won't get in to details but the phone's been drying out ever since and I've got a torx T5 screwdriver on the way so I can take it apart if needed. I tried to turn it on earlier today and it actually seems to almost be working perfectly ; I've got sound, vibration, WP7 boots up just fine and the touch screen is as responsive as ever but the one problem I do have is the backlight. I can only see things on the screen in pitch darkness. From what I've read, it looks like I might have to buy a new LCD screen but before ordering parts I'd like to get a few opinions about what I should try to get it working properly again.
Thanks in advance.
Click to expand...
Click to collapse
I'd try the bag-o-rice trick first, since even this late in the game I've heard that it can get the last moisture remnants out and solve some issues.
Sounds like the LCD needs to be replaced to me personally.

Thanks for the reply!
I've had it in a bowl of rice right next to a satellite decoder box (that gives off a little heat) ever since the accident so unless taking it apart completely (once I get my screwdriver) helps it looks like I'll need to buy some parts...
Would an LCD screen like this one be enough ?
http://cgi.ebay.fr/Original-LCD-Ecran-Display-Fit-HTC-TOUCH-HD2-II-T8585-/150427154446?pt=FR_Mobiles_PDAs_Autres&hash=item230628380e
Or do I need/would it be easier to replace with something like this LCD screen and touch screen ?
http://cgi.ebay.fr/ecran-TACTILE-LCD-assemble-pour-HTC-HD2-LEO-T8585-/120723712282?pt=FR_Mobiles_PDAs_Autres&hash=item1c1bb1a91a
Thanks again.

i will go defenitely for lcd + touch screen IF it comes mounted by factory... it will be very easy and more secure for your device.
but if you arent in hury wait 2-3 days just to make sure your phone its ok so you wouldnt i lose more money ( i work in a mobile shop service and wet phones have troubles after couple days if not at the beginning ), i hope everything turns ok .

Dim screen could also be caused by bad ic chip on the board that controls the display.

DJ_MiX said:
Dim screen could also be caused by bad ic chip on the board that controls the display.
Click to expand...
Click to collapse
What board exactly are you talking about? So do you think that changing the LCD and touch screen might not even solve my problem?

NeoGreendawg said:
What board exactly are you talking about? So do you think that changing the LCD and touch screen might not even solve my problem?
Click to expand...
Click to collapse
Motherboard, but I would attempt lcd replacement 1st, if fails it the ic om motherboard.

i had water damage on 2 phones, both work fine. sun, zip lock bag with rice, hair dryer < that worked for me. i read that dipping phone in 100% alcohol also helps get water out. (when water drys up it leaves residue, alcohol doesnt)
ps. it can take up to a month for everything to 100% dry up. my iphone had glitches, then glitches went away.

Samsung Galaxy S3 I9300 - Extra Screen Replacement Information

My Ex droped her Phone and it had Spider Webs all accross. Her Provider send it in to see what it would cost to fix. The Phone also would stop working correctly in the middle of calls.
It turns out buying a new one would have come cheaper atleast thats what came back as a answear.
So I decided to bite the apple and try replacing the Screen myself. My Ex was not happy because she thought with the second Problem it is not worth the effort to fix the Screen and maybe loose everything. My reasoning was that when the Spider Web Screen touches the Digitizer it will react strangely. So I went ahead and searched the web on how to do it. I ordered a Screen for $9 on ebay (free shipping) which came with a couple of Tools. More on those later.
One of the first Problems I found was that all instructions that I found showed the beginning and the end. But in the middle how the phone will look like when the glass is finaly taken off, I was unable to find much Information about it. Also doing it Redneck style without Special liquids and or a heat guns was no where to be found.
I decided to just try it. Disasembly is well documented and easy enough to do on this device. Atleast to the Point where most electronics are removed so that you can apply heat without too much problems. I decided on using a blow dryer to heat up the Display. I layed the Blow Dryer on the Counter turned it on and Held the phone up to it. Thinking if my fingers get too hot chances are it is too hot for the Display too.. Might be a little incaccurate to read the temperature like that but hey it worked. But soon after I started to remove the first pieces of broken glass I ran into Problems.
As per instructions I found, I put a Piece of tape accros the Screen so that the individuall pieces stayed ogether. That did not work at all for me. It just made the individual pieces push against the valuable digitizer below it. My next Problem was that the Tools that came with the replacement glass, especially the Little plastic Tools did not hold up to the Job und the tip was soon useless. I had to Switch to a Raizor blade. A couple of times I sliped and hit the Digitizer. Thinking oh well I guess I Need to get a new one. Luckely on the end it all worked out much better then I would have hoped. The left over glue I rubbed mostly off with my finger which worked out nicely. To clean it completely from ist glue took some time. The black rubber allong the side of the phone allso suffered. You might want to look out that that does not get riped out completely. I had enough left over so that the glass would sit on it good enough luckely.
Take a look at these Pictures and remember it works perfectly again for $9. While it is not for everyone to seperate a Glass from a Digitizer it is acctualy less fragile as you might think. The third Picture Shows you how it looked with all the scuff marks from taking off the glass. You can still see a few little marks on the end but hard to notice and much better then before. I am sure next time I will be more carefull and use the blade from the beginning on.
I got more Pictures and will improve this Thread for others that have to go through it. Feel free to PM me if you have any Questions. A list of other resources will also be included. This is only to explain and Show the bare state.

Reserved for links
Additional Screen Replacement Links:

Do you know if we can replace the metal frame on the side?
My device is bent. I mean. I fell on a rock with my device in my pocket and the rock directly hit the phone. Luckily I had a hsrd case and the device is still alive.
Sent from my GT-I9300 using Tapatalk

supreethms said:
Do you know if we can replace the metal frame on the side?
My device is bent. I mean. I fell on a rock with my device in my pocket and the rock directly hit the phone. Luckily I had a hsrd case and the device is still alive.
Sent from my GT-I9300 using Tapatalk
Click to expand...
Click to collapse
You should be able to find a new Frame for a resonable Price. Now to remove the digitizer from the Frame that is another Story. Not sure if it was the Glue or what Held it in place but I could not figure out how to get that out. luckely the two Buttons at the bottom survived the Screen removal and so I did not hat to take the Digitizer out.

Useful information and explains why repair shops will usually only replace the complete assembly. Read many complaints that those cheap ebay screens are plastic and easily scratched, not genuine gorilla glass replacements?
Sent from my GT-I9300 using Tapatalk

http://www.ebay.co.uk/itm/150998824149?_trksid=p2055119.m1438.l2649&ssPageName=STRK:MEBIDX:IT
I've ordered one of these as mines a bit scuffed and what looks like a small crack in it.

boomboomer said:
Useful information and explains why repair shops will usually only replace the complete assembly. Read many complaints that those cheap ebay screens are plastic and easily scratched, not genuine gorilla glass replacements?
Sent from my GT-I9300 using Tapatalk
Click to expand...
Click to collapse
It is definetly cheaper then the original but if you have done it once. Chances are You will be able to do it again much easier. So if the $9 Glass only holds for example a Year. You can just replace it again. Or spend a little more for a original replacement glass.
Now I should Point out if the rubber seal around it gets damaged in the process and if the 3M Tape that should come with the Screen is placed wrong it will Impact the sensitivity of the sreen touches. I guess I did it right because my Ex is happy how it performs and that is saying allot.

madmackem said:
http://www.ebay.co.uk/itm/150998824149?_trksid=p2055119.m1438.l2649&ssPageName=STRK:MEBIDX:IT
I've ordered one of these as mines a bit scuffed and what looks like a small crack in it.
Click to expand...
Click to collapse
If you get down to removing the digitizer from the Frame take a couple of Pictures and post them here.

LG V20 screen replacement!!!!!

Hey guys. I recently broke my LG V20 (AT&T varient.) It is just the top screen and not tbe LCD Digitizer. The 2nd screen is completly fine and its the main screen that's broken. Does anybody know a good tutorial and a good source to get tbe part ASAP?
Thanks in advanced.

velezj.att said:
Hey guys. I recently broke my LG V20 (AT&T varient.) It is just the top screen and not tbe LCD Digitizer. The 2nd screen is completly fine and its the main screen that's broken. Does anybody know a good tutorial and a good source to get tbe part ASAP?
Thanks in advanced.
Click to expand...
Click to collapse
Dude YouTube

Look up Jerry rig everything his YouTube channel has it all

velezj.att said:
Hey guys. I recently broke my LG V20 (AT&T varient.) It is just the top screen and not tbe LCD Digitizer. The 2nd screen is completly fine and its the main screen that's broken. Does anybody know a good tutorial and a good source to get tbe part ASAP?
Thanks in advanced.
Click to expand...
Click to collapse
As someone else said,youtube.
In the amount of time waiting for a reply, you could have just Googled the question.
And, the second screen, I do believe, is a single physical screen, partitioned by software. If one is trashed, both are I believe.

Thank you. I understand Youtube and Google. The problem with that is there are only like 3 videos, and each video the process is slightly different. When I try and search for the part, I find the glass/LCD digitizer ranging in price from $100-130. This is fine but the problem is I don't want to wait a few weeks to receive it, since all of the places I've found that sell it can't do expedited shipping, and if they do, they are all sold out. Lastly, I also found JUST the top layer of glass (no not a tempered glass protector, the actuall replacement) for only around $10-$20 in price, but there are ZERO videos on Youtube for that process, and a few people in the comments have even asked about this, with no luck.

A combo of multiple things....
This is a relatively new phone. Won't be lots of how tos available for one.
Second, what you are asking about is not a simple fix.
It requires either extreme cold such as, liquid nitrogen or 90% alcohol and dry ice cold. Or extreme heat. You either embrittle the glue with cold and peel it off in pieces or soften via heat and pull it loose in pieces. You run risk of killing your digitizer. Plan ahead accordingly.
You also *will* kill the polarizing layer in between digitizer and glass. Be prepared to replace this as well. Anyone who says otherwise is fibbing, IMO.
Then, you need something to remove the bubbles from the LOCA glue and gorilla glass sandwich.
Then reassemble.
Again: with the phones age, and a small supply chain in place due to the devices age, don't expect much in the way of how tos, or parts.
tl;dr
Not a simple fix. Chances are high you wont get it back to stock without a good technique and some moderately expensive tools.
Edited to add... There's a reason you find very few glass sellers, and lots of people selling digitizer/glass combos. .. The odds of a ****ed job are sky high, esp with phones with curved glass, like Samsung garbage.

On my V10 my front screen had cracked. Rather than try to replace just the digitizer I bought a dead V10 on eBay and replaced the full screen housing from that phone with my motherboard. Much easier to replace full screen assembly if you can find that way.
Sent from my LG-H918 using Tapatalk

I have a v20 Sprint..My Screen Is Cracked Some What At The Top..Will That Crack Cause The Phone To Freeze Up?
like Sometimes The Phone FREEZE BAD but when i press the screen I can still Hear The Sounds from the apps

velezj.att said:
Hey guys. I recently broke my LG V20 (AT&T varient.) It is just the top screen and not tbe LCD Digitizer. The 2nd screen is completly fine and its the main screen that's broken. Does anybody know a good tutorial and a good source to get tbe part ASAP?
Thanks in advanced.
Click to expand...
Click to collapse
https://www.fixez.com/store/lg/lg-v-series/lg-v20

Fixez - LG V20 Screen with Frame
Just thought I would "help" other LG V20 owners; but I just finished replacing the screen on mine after dropping it on the concrete floor in the parking garage at work. It actually landed face down and I had a crappy Incipio case, so it was a spiderweb of cracks although it still ran fine for 3 months until the lines got thicker and thicker.
Anyway, I ordered a replacement Screen with Frame from Fixez.com and just know that it is NOT OEM or even close. I got my phone working; but just some notes for anyone else who finds this and tries to replace the screen themselves.
Most YouTube videos out there are NOT accurate and you will end up having to "move" extra parts they do not show.
I got the FRAME replacement; but I think it would have been BETTER without because all the tiny pieces are GLUED onto the frame.
You MUST have the tools, especially that tweezer one and get a Hair Dryer, because the parts are TINY and GLUED so easier to loosen.
I broke the Headphone Jack, because the connectors are basically membranes, which is why I think you should just replace SCREEN.
I forgot to clean my front facing camera; but I cleaned the two rears ones, so just make sure you "alcohol and air spray" clean before closing.
It is beyond blurry and I do not want to take it apart; but it could actually be the "low quality" peephole, which is creating "flare and blur".​
Once I finished and turned it on, I was overjoyed; but after a week I can "see" more problems and just be aware that you really need OEM.
Problems:
Secondary Screen does not "show" when Main Screen is OFF; but it worked with original screen once option enabled.​The top part is not white-white; but just a "hair off" and it is like an "oval thumb circle" and might have been "touched" during manufacture.​Put some Arctic Silver CPU compound; because this "knock off" runs HOTTER and the first few boots felt like a "burn in" sequence.​There is no LG Logo at the bottom of the screen; so if you decide to "sell" it later, then it will be obvious that you are selling "refurbished".​The battery seems to drain faster; but I also noticed it does not "like" a FULL charge and runs nice and cold when lower battery charge.​Headphone jack broken. Does not light up when I look at screen. Sometimes "double tap" (KNOCKON) does not work correctly.​Sometimes I have to press Power Button twice to turn on screen. Sometimes it is once. Basically "sensors or integration" seem to have issues.​I just miss how the "little things" used to work perfectly, even when it was cracked.​
Basically, this screen feels like a cheap Chinese "knock off"; but I went for the "cheapest option" I found out there and you get what you pay for, so it works, but I hope this helps someone else out there to make an informed decision. Remember, Fixez (and ALL OTHERS) have a NO RETURN policy; because basically they state that it must be in NEW RESELLABLE condition and you are going to be sticking things, bending wires and removing plastic tabs. So do not listen to anyone and these repair shops will NOT return your money once you try to DIY.
If I had to do it again, then I would have spent more time looking for a screen with the LG Logo and at least try to get something with some OEM "guarantee or promise"; which Fixez NEVER made and I just went for Low Price and USA Based. Might have been better to get something OEM from Asia; because I got ganked anyway and I suspect this screen is going to shorten the lifespan of what was a beautiful LG V20 - H918 from T-Mobile.
:crying:

Does anyone know how to find a decent quality replacement of the glass and digitizer? I'll certainly keep the ease of 'no frame' in mind. I would like an oem product for sure. But I want my phone back asap, so I'll take what I can get