Database Users

[Helpe] error flash WP7

hello,
i have a error message during the flash wp7 (4 partition):
An error has occurred
Read below for more information
Error Description: send d000ff partition data failed
Info: .\RSPL\RSPL.cpp (1279)
Error Description: block send fail
Info: .\RSPL\RSPL.cpp (962)
Error Description: flash write failed.
Info: .\RSPL\RSPL.cpp (710)
can you helpe me?
ps: sorry i don't speak very well english... ^^

do you have MAGLARD 1.12 installed ?

yes magldr 1.12 is installed...
task29---> ok
Rom radio 2.15--->ok
Magldr 1.12--->ok
Rom WP7---> probleme with partition 4...

I kept getting a few strange error codes, rebooted phone did a hard reset within magdlr and just kept trying turned my antivirus off and then it worked, took 4 attempts before it actually installed so don't give up mate

Had the same Error, just changed the USB port throught which I was performing the Flashing, did a Task 29, and Flashed Magldr 1.12 again, Flashed WP7 and now enjoying it

Had the same error. Tried again and all was fine. Not sure what caused it.

Code error 1279 and 956
I got the error below after install MAGLDR112 and so I ran DWI.exe.
An error has occurred
Read below for more information
Error Description: send d000ff partition data failed
Info: .\RSPL\RSPL.cpp (1279)
Error Description:
Info: .\RSPL\RSPL.cpp (956)

I hv used WP7 on my HD2 and reflashed it to WM6.5 as i dont hv actovation key at that time.Now i hv arranged the key but i m also getting the same error. I hv tried more than 50 times but no luck. Task29 aslo failed on some blocks. plz help if anyone know the solution.i m able to flash 6.5 Roms.

I am having the same issue. I've been trying the above mentioned solutions and still no luck. I had W7 instaled before but i had change back to 6.5. For the past few weeks i have been trying to install back the W7 and i am stuck at the same error.
Any ideas?
Thank you for your help.

Solution...
You guys are probably flashing using a desktop and connecting the HD2 to the front usb port of the computer... Try using the back usb port (the usb port from the motherboard) usually the front ports from the case don't get enough power... had that error myself, and I just connected to the back and done hope this helps...

solution
Enable -
Services
4. Use Last 24 NAND

I had the same problem, just changed the USB port throught which I was performing the Flashing, did a Task 29, and Flashed Magldr 1.13 again, flashed WP7 but not working stop in flashing part 4, I connect my phone to usb port in netbook msi wind u100. Any idea?

Same error prople please please help i have tried everything i could zillion of times have not slept since the past sixteen hours please please help tell me what am i doing wrong
i was on winmo and then i flashed hspl2.08 success
then i installed latest radio 2.15 success
then i installed magldr success
then select services and select last 24 nand
select service and erase mbr
select usb flasher and i get the above error please help i just bought the hd2 yesterday

migatt said:
hello,
i have a error message during the flash wp7 (4 partition):
An error has occurred
Read below for more information
Error Description: send d000ff partition data failed
Info: .\RSPL\RSPL.cpp (1279)
Error Description: block send fail
Info: .\RSPL\RSPL.cpp (962)
Error Description: flash write failed.
Info: .\RSPL\RSPL.cpp (710)
can you helpe me?
ps: sorry i don't speak very well english... ^^
Click to expand...
Click to collapse
Try to install wm 6.5, you can do task29, and it is best to install wp7 - Magldr 1.13 => Services => UseLast24NAND.

Not working
I hav tried everything
Format SD cart
Use MGRLD 1.12 and 1.13
Use 3/3 USB ports on my laptop
Trie to instal different WP7 ROM
Nothing works
HSPL ok, Radio rom OK too. I have got instaled WP7 on my HTC HD2, but i want to reinstall it and something like this happen.
I have got the same error as dude above me. I spand two days on it and still nothing work.
Have you got some other tip for solution?
OMG I cant believe it, while i was writing this post, i tried once again to flash ROM wp7 AND IT WOKRS! Some magic i thing...
What I have done was in MGLRD use LAST 24NAND.
thx all of you.

[q] android software fails to install and gives errors

okayy.. this is my 2ND attempt at adding android to my HTC HD 2 as i have already messed up my 1st one...
i tried adding the DFT_Android rom to my HTC HD 2 Leo (T-Mobile), i did the HSPL_PKG install (2.8.0.HSPL or something...), i flashed the MAGLDR 111 and got to the USB FLASHING of the ANDROID ROM and it was flashing the partition ok, then it got to the 2nd partition and stop RIGHT before it was done (around 90%) and it gave me a FAIL INSTALL :
[Error happen
Read below for more information
Error Description: send partition data failed
Info: .\RSPL\RSPL.cpp (802)
Error Description:
Info: .\RSPL\RSPL.cpp (545)
.... now the phone restarts and ITS STUCK on the DFT dark forces team screen and it WONT BUDGE... can anybody help me out please ?...

Nand corrupted?

I have major problem with my nand memory.
Few days ago my hd2 hanged while I was doing some backup via Titanium Backup and since then I have a problem with my device.
Generally nand android builds are not working (boot animation stuck), some of them actually do work but with problems (f.e FC's on everything or do not recognise my SD card).
When I'm trying to flash WP7 usually an error occurs: (partition 4)
An error has occurred
Read below for more information
Error Description: send d000ff partition data failed
Info: .\RSPL\RSPL.cpp (1279)
Error Description: block send fail
Info: .\RSPL\RSPL.cpp (962)
Error Description: flash write failed.
Info: .\RSPL\RSPL.cpp (710)
Click to expand...
Click to collapse
I wrote usually becouse actually I have been able to flash it few times (3 or 4 on 20 attempts) but then windows stuck on boot logo or device hanged when I was trying add new contact.
I did Task 29, reflashed Radio and MAGLDR 1.13. Problem still persist...
Please anyone help!

Ziaren said:
I have major problem with my nand memory.
Few days ago my hd2 hanged while I was doing some backup via Titanium Backup and since then I have a problem with my device.
Generally nand android builds are not working (boot animation stuck), some of them actually do work but with problems (f.e FC's on everything or do not recognise my SD card).
When I'm trying to flash WP7 usually an error occurs: (partition 4)
I wrote usually becouse actually I have been able to flash it few times (3 or 4 on 20 attempts) but then windows stuck on boot logo or device hanged when I was trying add new contact.
I did Task 29, reflashed Radio and MAGLDR 1.13. Problem still persist...
Please anyone help!
Click to expand...
Click to collapse
Bro, did u got any anwser ??
please help, i have the same issue

Here is what I suggest you do : -
Flash a STOCK Winmo 6.5 ROM. Once that's done and you have Winmo 6.5 working, you'll atleast have your phone back up. Then I would suggest that you pick a LITE ROM to start with and see how that works for you. If it works, then move to your preferred ROM. Make sure that you're following instructions on how to flash back and forth to the letter.
Your device powers on. That's something you should be happy about.

im no developer but here is my solution
In my experience with this problem and its solution:
First remove the battery, and remove the SD card...
Second place the battery on the phone and reset it with the volume up key...
then take off battery and place the SD card back again, then place the battery...
restart the phone on plugged to a computer... (i do this on an WIN xp or WIN 7 machine).... so far it has crashed 3 times/same errors in the boot and this has worked.... i guess still some bugs need to be fixed...
(DONT KILL ME IF IT DOESNT HELP..IM NO EXPERT BUT ITS WORKED FOR ME..)

Try pulling your sim card, sd card & rebooting. If that doesnt work, try to flash an official rom from SD. (LEOIMG.nbh on root of SD, then boot with both volume buttons held) Upon 1st boot remove sim & sd. This should work, I had a simular problem and this fixed it. Android would not boot all the way, recovery wouldn't flash & WM gave me partition errors. I still had some issues in WM6.5 & could not flash the most recent EnergyROM with the newest HSPL. I eneded up calling warranty on mine. Hopefully the SD flash method will work for you.

KillaHurtz said:
Try pulling your sim card, sd card & rebooting. If that doesnt work, try to flash an official rom from SD. (LEOIMG.nbh on root of SD, then boot with both volume buttons held) Upon 1st boot remove sim & sd. This should work, I had a simular problem and this fixed it. Android would not boot all the way, recovery wouldn't flash & WM gave me partition errors. I still had some issues in WM6.5 & could not flash the most recent EnergyROM with the newest HSPL. I eneded up calling warranty on mine. Hopefully the SD flash method will work for you.
Click to expand...
Click to collapse
They only need to hold the volume down button to get the bootloader to come up not both volume buttons.

[Q] Help Needed: HD2 stuck after install MAGLDR

Hey all,
Firstly, I know there are many similar threads posted here, but none of them actually gave a solution to a problem I have.
What I did: tried to eventually put WP 7.8 using Pdaimatejam's ROM.
*My HD2 runned on WM 6.5 and was completely original
I followed all steps in chronological order:
-Installed HSPL 2.08.HSPL - Succeeded
-Installed MAGLDR - Says it succeeded
NOW, it rebooted itself, since then it always freezed at the White HTC LOGO screen.
By booting via the bootloader (Volume down+Powerbutton) I get the following information:
PB81100 HX-BC
SPL-2.08.HSPL 8G XE
0x05
CotullaHSPL 0x40
I still see Serial at the bottom. When Plugging in USB it shows that it's connected with USB.
Important:
I have tried to install MAGLDR again: Same result. It says it succeeded, but is stuck after booting.
I have NEVER seen the MAGLDR bootup (The black list)
I have NOT put an SD-card when doing this all (Maybe that's the problem)
I also have NOT done anything with the Radio, because I diidn't know exactly what it is and I didn't think it was necesserily.
Any help would be very very very appreciated.
- TSeven

You can't just skip steps and expect everything to work properly. Flash radio 2.15.50.14, then I think you should be fine. Also, how are you planning on running WP7 without an SD card? Buy one or if you have one (which you should) put it in the phone. Flashing HSPL, MAGLDR, the radio etc. won't interfere with your SD or SIM card.

sdcard is WP7 main memory... you must have SDcard during flashing process in phone...
read install tutorial from my signature

Nigeldg said:
You can't just skip steps and expect everything to work properly. Flash radio 2.15.50.14, then I think you should be fine. Also, how are you planning on running WP7 without an SD card? Buy one or if you have one (which you should) put it in the phone. Flashing HSPL, MAGLDR, the radio etc. won't interfere with your SD or SIM card.
Click to expand...
Click to collapse
I'll put an 2GB SD card in my HD2. Can I now Flash my phone with Radio 2.15.50.14 and will my problem be solved now?
Or should I first Flash Radio, then HSPL again and then MAGLDR again?
Thanks for your response by the way.

soedhier007 said:
I'll put an 2GB SD card in my HD2. Can I now Flash my phone with Radio 2.15.50.14 and will my problem be solved now?
Or should I first Flash Radio, then HSPL again and then MAGLDR again?
Thanks for your response by the way.
Click to expand...
Click to collapse
is not important when you flash radio... just flash it...

I think radio then MAGLDR. You don't need to reflash HSPL though.

Thanks all for helping me out, still have to search for the 2GB sd card... I'll tell you guys Monday if it worked.

Hey all,
Thanks for all your help! I'm stuck again though..
I've put an 4gb sd card into my HD2 and have flashed my phone with
the radio (Radio_Leo_2.15.50.14)
After flashing, I didn't got the MAGLDR bootloader, so I (like Nigeldg said) flashed my phone with
MAGLDR afterwards.
After that It worked and now I'm able to enter the MAGLDR bootloader with no problems.
Entered USB Flasher and:
put a WP7 (although, that's what I thought) ROM on my phone...
The name of the file is ( 3_HD2 Pdaimatejam Rom Wp7.8 OS 7.10.8835.35 v8.5 )
After installation however the installation program gave me 3 errors:
An error has occurred
Read below for more information
Error Description: send d000ff partition data failed
Info: .\RSPL\RSPL.cpp (1279)
Error Description: block send fail
Info: .\RSPL\RSPL.cpp (962)
Error Description: Block is after end.
Info: .\RSPL\RSPL.cpp (704)
I AM able to boot my HD2 and Windows 8 (surprisingly 8) booted normally, untill it said that it doesn't recognise my sd card. Only
option is to shut down my HD2.
I'm now thinking to put another ROM on it, I already installed on my pc only (3_HD2_20Pdaimatejam_20Rom_20Wp7.8_20OS_207.10.8858.136_20RMT_20v8.7) from Dxdy's links.
When I deleted my sd card from my HD2 and booted it, it still booted normally with the Windows 8 loading screen and the error about the sd.
I want to delete at first that ROM and put another one on it. How can I delete it? It is ( I think) not installed on the SD.

Tseven007 said:
Hey all,
Thanks for all your help! I'm stuck again though..
I've put an 4gb sd card into my HD2 and have flashed my phone with
the radio (Radio_Leo_2.15.50.14)
After flashing, I didn't got the MAGLDR bootloader, so I (like Nigeldg said) flashed my phone with
MAGLDR afterwards.
After that It worked and now I'm able to enter the MAGLDR bootloader with no problems.
Entered USB Flasher and:
put a WP7 (although, that's what I thought) ROM on my phone...
The name of the file is ( 3_HD2 Pdaimatejam Rom Wp7.8 OS 7.10.8835.35 v8.5 )
After installation however the installation program gave me 3 errors:
An error has occurred
Read below for more information
Error Description: send d000ff partition data failed
Info: .\RSPL\RSPL.cpp (1279)
Error Description: block send fail
Info: .\RSPL\RSPL.cpp (962)
Error Description: Block is after end.
Info: .\RSPL\RSPL.cpp (704)
I AM able to boot my HD2 and Windows 8 (surprisingly 8) booted normally, untill it said that it doesn't recognise my sd card. Only
option is to shut down my HD2.
I'm now thinking to put another ROM on it, I already installed on my pc only (3_HD2_20Pdaimatejam_20Rom_20Wp7.8_20OS_207.10.8858.136_20RMT_20v8.7) from Dxdy's links.
When I deleted my sd card from my HD2 and booted it, it still booted normally with the Windows 8 loading screen and the error about the sd.
I want to delete at first that ROM and put another one on it. How can I delete it? It is ( I think) not installed on the SD.
Click to expand...
Click to collapse
First you must go to Magldr to activate the last 24MB
>10 Services>4 UseLast24MB
If this doesn't help, you must use another SD-Card. WP doesnt like any type of card. I use a SanDisk Class 4 card whitch works fine. Search in the forums other persons experiences with SD-Cards. Changing the ROM won't help.

Tseven007 said:
Hey all,
Thanks for all your help! I'm stuck again though..
I've put an 4gb sd card into my HD2 and have flashed my phone with
the radio (Radio_Leo_2.15.50.14)
After flashing, I didn't got the MAGLDR bootloader, so I (like Nigeldg said) flashed my phone with
MAGLDR afterwards.
After that It worked and now I'm able to enter the MAGLDR bootloader with no problems.
Entered USB Flasher and:
put a WP7 (although, that's what I thought) ROM on my phone...
The name of the file is ( 3_HD2 Pdaimatejam Rom Wp7.8 OS 7.10.8835.35 v8.5 )
After installation however the installation program gave me 3 errors:
An error has occurred
Read below for more information
Error Description: send d000ff partition data failed
Info: .\RSPL\RSPL.cpp (1279)
Error Description: block send fail
Info: .\RSPL\RSPL.cpp (962)
Error Description: Block is after end.
Info: .\RSPL\RSPL.cpp (704)
I AM able to boot my HD2 and Windows 8 (surprisingly 8) booted normally, untill it said that it doesn't recognise my sd card. Only
option is to shut down my HD2.
I'm now thinking to put another ROM on it, I already installed on my pc only (3_HD2_20Pdaimatejam_20Rom_20Wp7.8_20OS_207.10.8858.136_20RMT_20v8.7) from Dxdy's links.
When I deleted my sd card from my HD2 and booted it, it still booted normally with the Windows 8 loading screen and the error about the sd.
I want to delete at first that ROM and put another one on it. How can I delete it? It is ( I think) not installed on the SD.
Click to expand...
Click to collapse
also same error for me,,,,,used class 4 sd card but no use

this error dont have anything with SDcard.... you not read install instructions... read tutorial from my signature
Error Description: send d000ff partition data failed
Info: .\RSPL\RSPL.cpp (1279)
Error Description: block send fail
Info: .\RSPL\RSPL.cpp (962)
Error Description: Block is after end.
Info: .\RSPL\RSPL.cpp (704)
Click to expand...
Click to collapse

my buttons (call key etc) dont respond in magldr boot screen.
dxdy said:
this error dont have anything with SDcard.... you not read install instructions... read tutorial from my signature
Click to expand...
Click to collapse
Hi all, not too hopeful for a reply since this thread is OLD.
I just got an HTC HD2 from my brother..its used etc. anyway.. it was running fine on winmo 6.5.
I decided to checkout online for tips on mods n getting it to look and run like a newer device? I thought id go for android ICS.
So, followed the steps and got the required items first. HSPL, Radio CUU and the HD2 toolkit that includes the magldr 1.13.
the first two flashes for hspl and rom were okay, however after flashing magldr, once the fone boots up in magldr mode, i could scroll up and down using the volume buttons but i cant SELECT anything, hence.. i cant get to the USB flasher mode to complete my 'quest'.
Has anyone experienced this or know why this happens? I am currently unable to use the fone.

judheim said:
... however after flashing magldr, once the fone boots up in magldr mode, i could scroll up and down using the volume buttons but i cant SELECT anything, hence.. i cant get to the USB flasher mode to complete my 'quest'.
Has anyone experienced this or know why this happens? I am currently unable to use the fone.
Click to expand...
Click to collapse
use green button to execute selected option...

Tseven007 said:
I'll put an 2GB SD card in my HD2. Can I now Flash my phone with Radio 2.15.50.14 and will my problem be solved now?
Or should I first Flash Radio, then HSPL again and then MAGLDR again?
Thanks for your response by the way.
Click to expand...
Click to collapse
Thanks, it's worked for my HTC PB81100, it stuck at HTC boot logo and now it's fixed

nooop
Pal ... Maybe Your Phone has The Special pack That is Unable to use Magldr ...

I had the problem of White Screen after installing Magldr
I had the same problem of White Screen after installing Magldr. Turns out it was the radio so followed the instructions Here >>>> .addictivetips.com/mobile/install-2-15-50-14-radio-on-htc-hd2
<<<<
Once installed it rebooted into MAGLDR then i could install a ROM.
Love this site btw!

[Q] Stuck In Load Screen

Helo all,
Before i begin, i would like to apologize my noob-ness to all the mods and seniors in the forum.
I have tried searching about this problem of mine, but has come up with various results, however, none ot the can solved mine.
My HTC HD2 has been installed with NexusHD2.ICS.CM9.HWA.V2.3 for the past few months now. Last nite after a batt drain, it shut down. And when i reboot, it stuck in that Android-cube-swirly thing.
These are my specs by the way:
HTC HD2 T8585, 512mb ROM
HSPL4
MAGLDR 113
ClockworkMod Recovery v1.3_250M
NexusHD2.ICS.CM9.HWA.V2.3
If've read somewhere that i could try a fresh boot of sorts. So i tried reinstalling everything, but i still couldnt get into the MAGLDR screen.
When using Recovery v1.3_250M, this error message came out
"An error has occurred
Read below for more information
Error Description: USB init failed
Info: .\RSPL\RSPL.cpp (736)"
Hence, i cannot reinstalled Android ICS (im using NAND method).
I also read somewhere about running a TASK29 berofe doing a fresh boot?? but i could not find what that is..
Pleeeeeeeeaasseee heeelllppp . . .