[Q] Stuck In Load Screen - HD2 Android Q&A, Help & Troubleshooting and Genera

Helo all,
Before i begin, i would like to apologize my noob-ness to all the mods and seniors in the forum.
I have tried searching about this problem of mine, but has come up with various results, however, none ot the can solved mine.
My HTC HD2 has been installed with NexusHD2.ICS.CM9.HWA.V2.3 for the past few months now. Last nite after a batt drain, it shut down. And when i reboot, it stuck in that Android-cube-swirly thing.
These are my specs by the way:
HTC HD2 T8585, 512mb ROM
HSPL4
MAGLDR 113
ClockworkMod Recovery v1.3_250M
NexusHD2.ICS.CM9.HWA.V2.3
If've read somewhere that i could try a fresh boot of sorts. So i tried reinstalling everything, but i still couldnt get into the MAGLDR screen.
When using Recovery v1.3_250M, this error message came out
"An error has occurred
Read below for more information
Error Description: USB init failed
Info: .\RSPL\RSPL.cpp (736)"
Hence, i cannot reinstalled Android ICS (im using NAND method).
I also read somewhere about running a TASK29 berofe doing a fresh boot?? but i could not find what that is..
Pleeeeeeeeaasseee heeelllppp . . .

Related

Nand corrupted?

I have major problem with my nand memory.
Few days ago my hd2 hanged while I was doing some backup via Titanium Backup and since then I have a problem with my device.
Generally nand android builds are not working (boot animation stuck), some of them actually do work but with problems (f.e FC's on everything or do not recognise my SD card).
When I'm trying to flash WP7 usually an error occurs: (partition 4)
An error has occurred
Read below for more information
Error Description: send d000ff partition data failed
Info: .\RSPL\RSPL.cpp (1279)
Error Description: block send fail
Info: .\RSPL\RSPL.cpp (962)
Error Description: flash write failed.
Info: .\RSPL\RSPL.cpp (710)
Click to expand...
Click to collapse
I wrote usually becouse actually I have been able to flash it few times (3 or 4 on 20 attempts) but then windows stuck on boot logo or device hanged when I was trying add new contact.
I did Task 29, reflashed Radio and MAGLDR 1.13. Problem still persist...
Please anyone help!
Ziaren said:
I have major problem with my nand memory.
Few days ago my hd2 hanged while I was doing some backup via Titanium Backup and since then I have a problem with my device.
Generally nand android builds are not working (boot animation stuck), some of them actually do work but with problems (f.e FC's on everything or do not recognise my SD card).
When I'm trying to flash WP7 usually an error occurs: (partition 4)
I wrote usually becouse actually I have been able to flash it few times (3 or 4 on 20 attempts) but then windows stuck on boot logo or device hanged when I was trying add new contact.
I did Task 29, reflashed Radio and MAGLDR 1.13. Problem still persist...
Please anyone help!
Click to expand...
Click to collapse
Bro, did u got any anwser ??
please help, i have the same issue
Here is what I suggest you do : -
Flash a STOCK Winmo 6.5 ROM. Once that's done and you have Winmo 6.5 working, you'll atleast have your phone back up. Then I would suggest that you pick a LITE ROM to start with and see how that works for you. If it works, then move to your preferred ROM. Make sure that you're following instructions on how to flash back and forth to the letter.
Your device powers on. That's something you should be happy about.
im no developer but here is my solution
In my experience with this problem and its solution:
First remove the battery, and remove the SD card...
Second place the battery on the phone and reset it with the volume up key...
then take off battery and place the SD card back again, then place the battery...
restart the phone on plugged to a computer... (i do this on an WIN xp or WIN 7 machine).... so far it has crashed 3 times/same errors in the boot and this has worked.... i guess still some bugs need to be fixed...
(DONT KILL ME IF IT DOESNT HELP..IM NO EXPERT BUT ITS WORKED FOR ME..)
Try pulling your sim card, sd card & rebooting. If that doesnt work, try to flash an official rom from SD. (LEOIMG.nbh on root of SD, then boot with both volume buttons held) Upon 1st boot remove sim & sd. This should work, I had a simular problem and this fixed it. Android would not boot all the way, recovery wouldn't flash & WM gave me partition errors. I still had some issues in WM6.5 & could not flash the most recent EnergyROM with the newest HSPL. I eneded up calling warranty on mine. Hopefully the SD flash method will work for you.
KillaHurtz said:
Try pulling your sim card, sd card & rebooting. If that doesnt work, try to flash an official rom from SD. (LEOIMG.nbh on root of SD, then boot with both volume buttons held) Upon 1st boot remove sim & sd. This should work, I had a simular problem and this fixed it. Android would not boot all the way, recovery wouldn't flash & WM gave me partition errors. I still had some issues in WM6.5 & could not flash the most recent EnergyROM with the newest HSPL. I eneded up calling warranty on mine. Hopefully the SD flash method will work for you.
Click to expand...
Click to collapse
They only need to hold the volume down button to get the bootloader to come up not both volume buttons.

Android does not want to install!

Hello, please help me!! I wanted to install android on my new HTC HD2.
What I did:
Installed hardslp 2.08
Radio 2.15.50.14
MAGLDR 1.13
after installed magldr it sent me to it's menu. I select USB flasher and then go to my Android Rom unrared folder, i run DAF file. Then it starts to isntall something(1-3) seconds. says everything is done and thren reboot system and says "nand kernel open failed" and sends me back to menu.
i tried many times and with another Android but nothing helped! Tried to install Clockwork mode, same problem. Then tried to isntall 29 but this program did not want to install saying that it couldnt connect with HD2. I thought it is something wrong with my computer. I borrowed my friend's laptop and tried to install Android from his. Installing process took a little bit more time but the same problem: It congratulates me that everything is done then reboots, then kernel error appears for 1 sec and sends me back to main menu.
Then I deleted Sync program(windws phone something..) and tried new ROM. Now DAF program says me next:
An error has occurred
Read below for more information
Error Description: USB init failed
Info: .\RSPL\RSPL.cpp (736)
Please help me !!
Hi,
Which ROM are you trying to install?
Which operating system have you got on your pc/laptop?
Are you right clicking on the DAF and selecting run as administrator?
Also when you go to USB Flasher and connect your HD2 to your computer are you giving a minute to establish a connection?
Give it a minute to establish connection, and try another Rom. Maybe your HD2 is 512 (EU), and you are trying to install ROM for 1024 HD2 (Tmobile US).
Did you read, maybe it is clockwork rom, not magldr?
Here is the link for MAGLDR flashing rom, stock Desire
http://forum.xda-developers.com/showthread.php?t=893620
it does not support ext partitions on sd card. But you can try another roms. And if you dont know how to flash it via Clockwork, here is the link
http://forum.xda-developers.com/showthread.php?t=1044830
p.s. Better ROMs are that that you flash via clockwork. Study that, it is easy.
Thanks to guys who wrote that tutorials
And here are all ROMs for HD2
http://forum.xda-developers.com/showthread.php?t=1044830

[Q] Im stuck. White screen

Ok. I have a HTC HD2 t-mobile. Someone gave it to me to see if I can fix it. So I have NO clue how it got to the point it is at now. All I know is that you power on and its a white screen. No HTC logo. Just white.
Enter boot loader: Red/Green/Blue/Black/White.... Its says:
PB81120 SS-B3
SPL-2.10.0000 8G XE
MicroP(LED) 0x05
MicroP(TOUCH) 0x50
SERIAL
Thats it. It doesnt connect to the computer.
What can I do? I tried:
CLEAN INSTALL
It’s a pretty long process, however, it takes a shorter time than the Installation of NAND Android. It takes me about 15minutes. It should take you about half an hour but no more than half an hour.
HSPL3, -2.08.HSPL.
[Head to my guide on How to install HSPL3, if you haven't install HSPL3 yet.]
Radio Version that supports 576 RAM(Radio2.15.50.14).
[Head to my guide on How to install radio , if you haven't install a suitable radio version yet.]
Wipe phone memory completely.
Install DFT MAGLDR.
Install ClockworkMod Recovery.
Create EXT3 Partition with ClockworkMod Recovery. (This step will wipe everything on our SD Card.)
Transfer ROM(zip file) to SD Card with ClockworkMod Recovery.
Install ROM from SD Card with ClockworkMod Recovery.
Details will be provided for each of the 6 steps.
But the phone and computer cant communicate. I have tried a hard reset. So thats where I am at now.
temp removed.
Ok. So I tried to flash the stock ROM from the SD card. It didnt complete. It says that it failed. It says at the top
00018003
LEOIMG.nbh - FAIL
Error happen
Read below for more information
Error Description: USB init failed
Info: .\RSPL\RSPL.cpp (723)
Error Description: wait marker fails
Info: .\RSPL\BootLoader.cpp (225)
When I try to install HSPL3 I get this error
CRITICAL ERROR
FLOW: 00000006
Error code: 00000014
Description Unknown
I can not get HSLP on my phone. I have tried versions 2,3 and 4... Is the phone done???
So I know I am a pain. But I have searched and read just about everything I can. I have tried to flash the stock ROM, I get an error of Radio Fail. I can not flash any other ROMS because I can not install HSLP.... I can connect via USB. But Windows Mobile Device center does not acknowledge the phone. I have ran the Task29... well tried... it says image is corrupted. I have even stuck the dang thing in the freezer like I have seen in random posts. Nothing but a really cold phone.
When I try and install HSPL3 I get an option to choose 2.08.HSPL or 2.08.0000 I have tried both. I get the critical error... Error code 16 description unknown.
I have tried following every set of directions I can locate in xda... Nothing has worked at all.
McSpammer5 said:
temp removed.
Click to expand...
Click to collapse
???What does that mean???
Have you tried reflashing window mobile???
Sent from my LG-P999 using xda premium
Yes I tried to reflash several times. I went and bought a new SD card. Solved it. Got windows working properly... Now to move on to installing Android
yesiamanoob said:
Yes I tried to reflash several times. I went and bought a new SD card. Solved it. Got windows working properly... Now to move on to installing Android
Click to expand...
Click to collapse
Great...
Sent from my LG-P999 using xda premium
Hi to the experts!
I have a very similar problem, maybe "almost" identical...
My HD2 (Australian Telstra, stock in almost every way), and it has been reliable for 2 years from new.
Then last Saturday night it started "failing to load HTC Sense", but all the WinMo 6.5 stuff was still fine. This lasted for 2 days and I thought it was stable like this so I would have time to look for a new phone, but last night I turned it off and on again, and all I have is the white screen. Mine has the green htc on it, but the only way to make it go away is to take out the battery.
I tried the volume down / power ON and I get the RGB+W screen, and when I plugged it in via USB to my new laptop it loaded drivers and initiated Windows mobile device center - but it won't recognise that there is a device there.
Now my very strong desire is to somehow boot it to allow recovery of my contacts directory - I have just started a new job and have probably 40 or so new people in there since my last backup.
What are my options? Is there anyway to boot from SD card without erasing the whole of system memory??
Failing that, how do I flash back to stock?
thanks (in hope)
..Neil
Stock WM
Try installing stock WM 6.5. There are many links available for the same, google it.
Do this without the memory card.
Enter Bootloader by pressing volume down and power on button together.
Then run the WM ROM file on your computer. You must see the progress bar on your phone. Let it settle down.
Hope that helps..!!

[Q] Help Needed: HD2 stuck after install MAGLDR

Hey all,
Firstly, I know there are many similar threads posted here, but none of them actually gave a solution to a problem I have.
What I did: tried to eventually put WP 7.8 using Pdaimatejam's ROM.
*My HD2 runned on WM 6.5 and was completely original
I followed all steps in chronological order:
-Installed HSPL 2.08.HSPL - Succeeded
-Installed MAGLDR - Says it succeeded
NOW, it rebooted itself, since then it always freezed at the White HTC LOGO screen.
By booting via the bootloader (Volume down+Powerbutton) I get the following information:
PB81100 HX-BC
SPL-2.08.HSPL 8G XE
0x05
CotullaHSPL 0x40
I still see Serial at the bottom. When Plugging in USB it shows that it's connected with USB.
Important:
I have tried to install MAGLDR again: Same result. It says it succeeded, but is stuck after booting.
I have NEVER seen the MAGLDR bootup (The black list)
I have NOT put an SD-card when doing this all (Maybe that's the problem)
I also have NOT done anything with the Radio, because I diidn't know exactly what it is and I didn't think it was necesserily.
Any help would be very very very appreciated.
- TSeven
You can't just skip steps and expect everything to work properly. Flash radio 2.15.50.14, then I think you should be fine. Also, how are you planning on running WP7 without an SD card? Buy one or if you have one (which you should) put it in the phone. Flashing HSPL, MAGLDR, the radio etc. won't interfere with your SD or SIM card.
sdcard is WP7 main memory... you must have SDcard during flashing process in phone...
read install tutorial from my signature
Nigeldg said:
You can't just skip steps and expect everything to work properly. Flash radio 2.15.50.14, then I think you should be fine. Also, how are you planning on running WP7 without an SD card? Buy one or if you have one (which you should) put it in the phone. Flashing HSPL, MAGLDR, the radio etc. won't interfere with your SD or SIM card.
Click to expand...
Click to collapse
I'll put an 2GB SD card in my HD2. Can I now Flash my phone with Radio 2.15.50.14 and will my problem be solved now?
Or should I first Flash Radio, then HSPL again and then MAGLDR again?
Thanks for your response by the way.
soedhier007 said:
I'll put an 2GB SD card in my HD2. Can I now Flash my phone with Radio 2.15.50.14 and will my problem be solved now?
Or should I first Flash Radio, then HSPL again and then MAGLDR again?
Thanks for your response by the way.
Click to expand...
Click to collapse
is not important when you flash radio... just flash it...
I think radio then MAGLDR. You don't need to reflash HSPL though.
Thanks all for helping me out, still have to search for the 2GB sd card... I'll tell you guys Monday if it worked.
Hey all,
Thanks for all your help! I'm stuck again though..
I've put an 4gb sd card into my HD2 and have flashed my phone with
the radio (Radio_Leo_2.15.50.14)
After flashing, I didn't got the MAGLDR bootloader, so I (like Nigeldg said) flashed my phone with
MAGLDR afterwards.
After that It worked and now I'm able to enter the MAGLDR bootloader with no problems.
Entered USB Flasher and:
put a WP7 (although, that's what I thought) ROM on my phone...
The name of the file is ( 3_HD2 Pdaimatejam Rom Wp7.8 OS 7.10.8835.35 v8.5 )
After installation however the installation program gave me 3 errors:
An error has occurred
Read below for more information
Error Description: send d000ff partition data failed
Info: .\RSPL\RSPL.cpp (1279)
Error Description: block send fail
Info: .\RSPL\RSPL.cpp (962)
Error Description: Block is after end.
Info: .\RSPL\RSPL.cpp (704)
I AM able to boot my HD2 and Windows 8 (surprisingly 8) booted normally, untill it said that it doesn't recognise my sd card. Only
option is to shut down my HD2.
I'm now thinking to put another ROM on it, I already installed on my pc only (3_HD2_20Pdaimatejam_20Rom_20Wp7.8_20OS_207.10.8858.136_20RMT_20v8.7) from Dxdy's links.
When I deleted my sd card from my HD2 and booted it, it still booted normally with the Windows 8 loading screen and the error about the sd.
I want to delete at first that ROM and put another one on it. How can I delete it? It is ( I think) not installed on the SD.
Tseven007 said:
Hey all,
Thanks for all your help! I'm stuck again though..
I've put an 4gb sd card into my HD2 and have flashed my phone with
the radio (Radio_Leo_2.15.50.14)
After flashing, I didn't got the MAGLDR bootloader, so I (like Nigeldg said) flashed my phone with
MAGLDR afterwards.
After that It worked and now I'm able to enter the MAGLDR bootloader with no problems.
Entered USB Flasher and:
put a WP7 (although, that's what I thought) ROM on my phone...
The name of the file is ( 3_HD2 Pdaimatejam Rom Wp7.8 OS 7.10.8835.35 v8.5 )
After installation however the installation program gave me 3 errors:
An error has occurred
Read below for more information
Error Description: send d000ff partition data failed
Info: .\RSPL\RSPL.cpp (1279)
Error Description: block send fail
Info: .\RSPL\RSPL.cpp (962)
Error Description: Block is after end.
Info: .\RSPL\RSPL.cpp (704)
I AM able to boot my HD2 and Windows 8 (surprisingly 8) booted normally, untill it said that it doesn't recognise my sd card. Only
option is to shut down my HD2.
I'm now thinking to put another ROM on it, I already installed on my pc only (3_HD2_20Pdaimatejam_20Rom_20Wp7.8_20OS_207.10.8858.136_20RMT_20v8.7) from Dxdy's links.
When I deleted my sd card from my HD2 and booted it, it still booted normally with the Windows 8 loading screen and the error about the sd.
I want to delete at first that ROM and put another one on it. How can I delete it? It is ( I think) not installed on the SD.
Click to expand...
Click to collapse
First you must go to Magldr to activate the last 24MB
>10 Services>4 UseLast24MB
If this doesn't help, you must use another SD-Card. WP doesnt like any type of card. I use a SanDisk Class 4 card whitch works fine. Search in the forums other persons experiences with SD-Cards. Changing the ROM won't help.
Tseven007 said:
Hey all,
Thanks for all your help! I'm stuck again though..
I've put an 4gb sd card into my HD2 and have flashed my phone with
the radio (Radio_Leo_2.15.50.14)
After flashing, I didn't got the MAGLDR bootloader, so I (like Nigeldg said) flashed my phone with
MAGLDR afterwards.
After that It worked and now I'm able to enter the MAGLDR bootloader with no problems.
Entered USB Flasher and:
put a WP7 (although, that's what I thought) ROM on my phone...
The name of the file is ( 3_HD2 Pdaimatejam Rom Wp7.8 OS 7.10.8835.35 v8.5 )
After installation however the installation program gave me 3 errors:
An error has occurred
Read below for more information
Error Description: send d000ff partition data failed
Info: .\RSPL\RSPL.cpp (1279)
Error Description: block send fail
Info: .\RSPL\RSPL.cpp (962)
Error Description: Block is after end.
Info: .\RSPL\RSPL.cpp (704)
I AM able to boot my HD2 and Windows 8 (surprisingly 8) booted normally, untill it said that it doesn't recognise my sd card. Only
option is to shut down my HD2.
I'm now thinking to put another ROM on it, I already installed on my pc only (3_HD2_20Pdaimatejam_20Rom_20Wp7.8_20OS_207.10.8858.136_20RMT_20v8.7) from Dxdy's links.
When I deleted my sd card from my HD2 and booted it, it still booted normally with the Windows 8 loading screen and the error about the sd.
I want to delete at first that ROM and put another one on it. How can I delete it? It is ( I think) not installed on the SD.
Click to expand...
Click to collapse
also same error for me,,,,,used class 4 sd card but no use
this error dont have anything with SDcard.... you not read install instructions... read tutorial from my signature
Error Description: send d000ff partition data failed
Info: .\RSPL\RSPL.cpp (1279)
Error Description: block send fail
Info: .\RSPL\RSPL.cpp (962)
Error Description: Block is after end.
Info: .\RSPL\RSPL.cpp (704)
Click to expand...
Click to collapse
my buttons (call key etc) dont respond in magldr boot screen.
dxdy said:
this error dont have anything with SDcard.... you not read install instructions... read tutorial from my signature
Click to expand...
Click to collapse
Hi all, not too hopeful for a reply since this thread is OLD.
I just got an HTC HD2 from my brother..its used etc. anyway.. it was running fine on winmo 6.5.
I decided to checkout online for tips on mods n getting it to look and run like a newer device? I thought id go for android ICS.
So, followed the steps and got the required items first. HSPL, Radio CUU and the HD2 toolkit that includes the magldr 1.13.
the first two flashes for hspl and rom were okay, however after flashing magldr, once the fone boots up in magldr mode, i could scroll up and down using the volume buttons but i cant SELECT anything, hence.. i cant get to the USB flasher mode to complete my 'quest'.
Has anyone experienced this or know why this happens? I am currently unable to use the fone.
judheim said:
... however after flashing magldr, once the fone boots up in magldr mode, i could scroll up and down using the volume buttons but i cant SELECT anything, hence.. i cant get to the USB flasher mode to complete my 'quest'.
Has anyone experienced this or know why this happens? I am currently unable to use the fone.
Click to expand...
Click to collapse
use green button to execute selected option...
Tseven007 said:
I'll put an 2GB SD card in my HD2. Can I now Flash my phone with Radio 2.15.50.14 and will my problem be solved now?
Or should I first Flash Radio, then HSPL again and then MAGLDR again?
Thanks for your response by the way.
Click to expand...
Click to collapse
Thanks, it's worked for my HTC PB81100, it stuck at HTC boot logo and now it's fixed
nooop
Pal ... Maybe Your Phone has The Special pack That is Unable to use Magldr ...
I had the problem of White Screen after installing Magldr
I had the same problem of White Screen after installing Magldr. Turns out it was the radio so followed the instructions Here >>>> .addictivetips.com/mobile/install-2-15-50-14-radio-on-htc-hd2
<<<<
Once installed it rebooted into MAGLDR then i could install a ROM.
Love this site btw!

[Q] Really need some help flashing to Win7.8 :-[

Hello
I'd really apprecaite some advice on flashing my HD2 to win7.8 i seem to keep running into the same roadblock. I've read and watched many tutorials but i keep getting the same error.
Basically i wipe my device, load magldr, boot into magldr and go to option 10 then option 4 for the last 24 option. I then go to USB flasher and attempt to flash a rom which always seems to fail the flashing on the 4th partition around 3quaters of the way with the following error.
Error Description: send d000ff partition data failed
Info: .\RSPL\RSPL.cpp (1279)
Error Description: block send fail
Info: .\RSPL\RSPL.cpp (962)
Error Description: flash write failed.
Info: .\RSPL\RSPL.cpp (710)
I've tried:
Formatting SD card on my laptop
Formatting sd card via magldr service menu
Tried a different smaller sandisk SD card.
Tried no SD card
Trying another win 7.8 ROM
installing hpsl4 and a custom RUU (not sure what they do but still got to the same stage)
Is anyone able to help me get this installed at all i'd be eternally grateful! Perhaps help me decipher what this error message alluds to?
Thank you for any assistance!
Just tried repartitioning in NAND to 300mb/45mb and instead of getting a red message when magldr first boots of "sd kernal failure" i get
nand kernal open failure could this be linked possibly?
Thanks again
Ok i'm about ready to give up if there are any experts around that could spare me 30 minutes of their time i'd glady reimmburse them for their time via paypal! Just need a little bit of troubleshooting help and confirm that the process i am taking is the correct one, i'm bound to be doing somthing stupid....
Managed to Flash win6.5 and also andriod Jellybean and Kitkit on the device but never win7.8 always get that error in the first post! :-[ insane!
Never disappoint there's always Somebody to help you ...
Tapley said:
Hello
I'd really apprecaite some advice on flashing my HD2 to win7.8 i seem to keep running into the same roadblock. I've read and watched many tutorials but i keep getting the same error.
Basically i wipe my device, load magldr, boot into magldr and go to option 10 then option 4 for the last 24 option. I then go to USB flasher and attempt to flash a rom which always seems to fail the flashing on the 4th partition around 3quaters of the way with the following error.
Error Description: send d000ff partition data failed
Info: .\RSPL\RSPL.cpp (1279)
Error Description: block send fail
Info: .\RSPL\RSPL.cpp (962)
Error Description: flash write failed.
Info: .\RSPL\RSPL.cpp (710)
I've tried:
Formatting SD card on my laptop
Formatting sd card via magldr service menu
Tried a different smaller sandisk SD card.
Tried no SD card
Trying another win 7.8 ROM
installing hpsl4 and a custom RUU (not sure what they do but still got to the same stage)
Is anyone able to help me get this installed at all i'd be eternally grateful! Perhaps help me decipher what this error message alluds to?
Thank you for any assistance!
Click to expand...
Click to collapse
My Dear friend ... First I'm sorry of seeing your thread late But now I'm here to help :laugh: ... as I read , you have problem with WPH installing ? ... so I'll give you some notes maybe you had left one of them ...
1- you should have HSPL 2.08 so if you don't have , Just install 2.08
2- you should do a Task29
3- install MAGLDR 1.13
4-enable "last 24 NAND" option in "services" menu of MAGLDR
5- format your SDcard
6- put it in the shut downed phone
7- install the WPH ROM but some times it gives errors at the beginning of the installation if you had that , it means the driver isn't installed so that you should install using Win XP but if the problem is that the process gives error in the middle / end of installation , it is usual and you have to install again and again to make it installed correctly ...
8- enjoy ( Due to being very hard , many people can't do this part so if you couldn't , just tell me to give you the Guide :laugh: )
NOTE : I tested that HD2O ROMs and usually have such problems so I recommend you to try PDAimatejam WPH 7.8 ROM , it is better and also all working ...
also you can Multi-Boot having both WPH and Android at the same time and it's the Best ( because WPH is really nice but has Battery drain and Android is good in battery and also nice :laugh: ) if were interested in that you can try this ... If had any Questions , I'll be Glad to answer ... Good luck
With Best Wishes
Hitman1376​
May you please tell me how to re-partition in nand ?

Categories

Resources