Related
Hi, i was going to upgrade to ArtemisV9 from Artemis v8. Had some stability problems with v8 so I thought making task 28 with MTTY. When I tried to flash artemis from the bootloader after that , the bar stayed at 0% so I had to cancel. Have tried flashing both via USB and from the storage card, but the progress bar never goes past 0%. When I start the phone it is stuck with the picture with hTc. Please help
task 28 or 29?
as far as i know task 29 also removes the radio. try flashing a radio rom first and after flash the rom.
Ultimaex said:
task 28 or 29?
as far as i know task 29 also removes the radio. try flashing a radio rom first and after flash the rom.
Click to expand...
Click to collapse
Thanks, but i have tried to flash the radio again but i will not work. I meant task 29. When I try to flash radio/rom the black screen with hTc and progresbar appears but i will not start. When I start the telephone the wihite screen with green hTc stucks, if I press vol down and reset the bootloader starts. Active sync can´t connect with the telephone, is this necesarry if you flash from bootloader?
it's neccessary full stop! there's your issue. This is how I flash the HD2:
1. Task29 & radio
2. Boot into bootloader
3. flash ROM once it says 'USB'
4. boot first time
5. hard reset
6. set phone up
All works fine
EddyOS said:
it's neccessary full stop! there's your issue. This is how I flash the HD2:
1. Task29 & radio
2. Boot into bootloader
3. flash ROM once it says 'USB'
4. boot first time
5. hard reset
6. set phone up
All works fine
Click to expand...
Click to collapse
I renamed the radio to LEOIMG.nbh and put it on my storage card, tried mtty again and then tried to enter bootloader, a white screen with Loading appears but gets stuck. I tried to renamed artemis to LEOIMG.nbh with the same result. If I tries to flash with USB, the black screen with progressbar appears and gets stuck at 0%. I have tried to flash stock rom with same result both with the exe file and I tried to extreact the nbh file and placed it on the storage card. Any suggestions how to get my phone to work.
Please
No one that have any suggestions? Is it possible that I have crashed the phone and that its not possibly to get any rom to work? I have Hspl so the warranty is gone.
with phone in bootloader mode.
what spl does it show exactly?
when you connect the usb cable, the word serial changes to usb, correct?
is your phone provider locked, and if so do you have the correct provider stock rom available?
do you have file extensions visible on your pc? (it isn't unknown for people to rename the nbh to "leoimg.nbh.nbh" by mistake.)
when it sticks on the white screen are there any numbers at the bottom of the screen?
samsamuel said:
with phone in bootloader mode.
what spl does it show exactly?
when you connect the usb cable, the word serial changes to usb, correct?
is your phone provider locked, and if so do you have the correct provider stock rom available?
do you have file extensions visible on your pc? (it isn't unknown for people to rename the nbh to "leoimg.nbh.nbh" by mistake.)
when it sticks on the white screen are there any numbers at the bottom of the screen?
Click to expand...
Click to collapse
Thank you, Im realy desperate.
SPL-2.08.0000 8G XE
Yes when Iconnect the serial changes to usb.
No it´s not provider locked
No, the filename is LEOIMG.nbh (if I take away .nbh it only says file and nothing happens from bootloader)
Now I renamed Artemis v9 to LEOIMG.nbh started the bootloader. A White screen with blue text Loading ... nothing more
ok, so you have spl 2.08.0000 which isn't hspl so the cooked roms don't work. . . and spl 2.08 won't let itself be downgraded by stock rom flash so they won't work.
connect to usb in bootloader
run hspl2
choose 2.08.hspl NOT 2.08.0000 in the list.
return to bootloader mode
should now say spl 2.08.hspl
flash your rom over usb
if it doesn't boot check radio
samsamuel said:
ok, so you have spl 2.08.0000 which isn't hspl so the cooked roms don't work. . . and spl 2.08 won't let itself be downgraded by stock rom flash so they won't work.
connect to usb in bootloader
run hspl2
choose 2.08.hspl NOT 2.08.0000 in the list.
return to bootloader mode
should now say spl 2.08.hspl
flash your rom over usb
if it doesn't boot check radio
Click to expand...
Click to collapse
Thank you for taking time. You realy saved my day. Now I feel like a complete idiot. Thanks again.
no worries. you can sit back and breathe again now.
Hi there! I have a problem after install MAGLDR :/ I connected my HD2 to computer with ActiveSync, runned ROMUpdateUtility from computer, on my phone there was a tricolour screen, then self-reset and phone is freezing on white HTC LOGO. I tried to turn off my phone, remove battery... I'm also turning my phone on with press vol down + power - I have 3 colour screen and now what? PLEASE HELP!
Connect your HD2 to your laptop/pc... boot it while pressing volume down.. wait untill it says usb in the bottom of your screen. Now you can flash HSPL 2.08 and flash a custom or original rom.
I had the same.. gonna stick with RAM roms untill this is nand stuff is sorted out
I have the same problem... but after reflash HSPL 2.08 there will be no change. Could not start the machine.
How can flash rom from pc without booting the machine?
I couldn't understand "Now you can flash HSPL 2.08 and flash a custom or original rom." the second step ...
solved!
I had the same problem.
The issue it's the radio.
install 2.15.50.14
http://www.multiupload.com/QP0IWGY42F
Hi,
After installing hspl 2.08 and then going on to install magdlr, when successful and rebooting it just stayed on the HTC logo screen. It wont reset but it will enter into bootloader. How exactly do i fix this. I tried reinstalling HSPL but it is still stuck on that screen. How would i change this 'problematic radio'?
I relly need to fix my phone so any help would be appreciated! Thanks
sexyseamus said:
Hi,
After installing hspl 2.08 and then going on to install magdlr, when successful and rebooting it just stayed on the HTC logo screen. It wont reset but it will enter into bootloader. How exactly do i fix this. I tried reinstalling HSPL but it is still stuck on that screen. How would i change this 'problematic radio'?
I relly need to fix my phone so any help would be appreciated! Thanks
Click to expand...
Click to collapse
Download a compatible radio (eg 2.15.50 in post above), boot to bootloader (switch off, vol down + power on (keep holding vol down until it boots), connect to pc and when usb shows on screen run the CustomRUU.exe in the radio download. (if there isn't one included you can take any one from a custom wm rom). You flash the radio the same way that you flash a rom.
Thanks for the quick response! I have tried doing this before and just tried the custom RUU posted above but when i run it where it says the image thats on the phone it is blank. Even so i click to update it and both on the phone and pc it stays at 0%. I don't know what to do!
sexyseamus said:
Thanks for the quick response! I have tried doing this before and just tried the custom RUU posted above but when i run it where it says the image thats on the phone it is blank. Even so i click to update it and both on the phone and pc it stays at 0%. I don't know what to do!
Click to expand...
Click to collapse
Are you sure you have HSPL installed properly. In bootloader mode, check the spl version - it should show as 2.08.hspl, not 2.08.0000 or any other hspl version.
In bootloader mode it says SPL 2.08.0000? When installing it i did select the HSPL 2.08?? What should i do? Thanks
sexyseamus said:
In bootloader mode it says SPL 2.08.0000? When installing it i did select the HSPL 2.08?? What should i do? Thanks
Click to expand...
Click to collapse
I had your problem and for some reason when I first ran hspl the first time and put 2.08 on my phone it said it worked but it didn't actually do anything.
Just reinstall 2.08 HSPL on your phone and then run MAGLDR.
Similar Scenario
I installed 2.08.HSPL - confirm at boot loader screen
I installed MAGLDR 1.13 with success
Flashed HD2_Core_Droid_Desire_HD_V1.5_NAND_ONLY_LEO1024_TMOUS to my phone with success
Phone worked fine for about a day and a half and froze up
Pulled battery and restarted to white screen
I can't seem to roll back the SPL, reinstall the MAGLDR, or install a different radio.
ROM Update Utility appears to start to work and phone restarts and I get an error message that the image is corrupt.
Any ideas?
OK, so i am trying to load the stock rom back on my old HD2 to send back to t-mobile.
My phone has a broken flex cable going to the bottom buttons so i cannot hit the power button.
I downloaded the stock rom from t-mobile and have it both on sd card and on computer.
I can boot the phone to the point where it wants me to load the rom from SD card, i just cannot hit the power button to accept.
So i tried to do it from the computer. when i do, it just hangs at 8%.
Does anyone have any idea how I can put stock rom back on it?
Hold your volume down button down while you power,on your HD2. When you see the multicolor bootloader screen come up connect your USB cable to the HD2 and computer. Wait for the Serial in the white bar of bootloader to change to USB then run the RUU for the T-Mobile ROM. After you have flashed the ROM download HSPL 4 (linked in my sig) and run it but select SPL 3.03.0000 when it asks what version you want to flash. When you are done runningvthe HSPL utility boot into bootloader again to make sure you have SPL -3.03.0000. If you do and you should ypu are good for warranty.
T-Macgnolia said:
Hold your volume down button down while you power,on your HD2. When you see the multicolor bootloader screen come up connect your USB cable to the HD2 and computer. Wait for the Serial in the white bar of bootloader to change to USB then run the RUU for the T-Mobile ROM. After you have flashed the ROM download HSPL 4 (linked in my sig) and run it but select SPL 3.03.0000 when it asks what version you want to flash. When you are done runningvthe HSPL utility boot into bootloader again to make sure you have SPL -3.03.0000. If you do and you should ypu are good for warranty.
Click to expand...
Click to collapse
This is what i am doing, but it just hangs at 8% no matter what..
bnd10706 said:
This is what i am doing, but it just hangs at 8% no matter what..
Click to expand...
Click to collapse
Which one the ROM or HSPL?
T-Macgnolia said:
Which one the ROM or HSPL?
Click to expand...
Click to collapse
I am trying to load the rom first. I cant boot anything. it just says update failed when i try to boot
bnd10706 said:
I am trying to load the rom first. I cant boot anything. it just says update failed when i try to boot
Click to expand...
Click to collapse
Have you tried flashing via SD card? Here is a guide on how to do this.
Also I recomend you flash HSL first as it might help.
How do i flash HPSL first? I cant get the phone into sync with it?
bnd10706 said:
How do i flash HPSL first? I cant get the phone into sync with it?
Click to expand...
Click to collapse
You don't have to have to be synced through ActiveSync you use HTC USB sync. Click on my guide linked in my sig and follow the instructions there on how to flash HSPL you will see what I mean.
I reloaded HPSL 2.08 and then tried to install the stock firmware via usb and it still hangs at 8%. I wonder if i try to install a different version?
I cannot boot from SD since my bottom keys dont work. I cannot click the call button to accept.
bnd10706 said:
I reloaded HPSL 2.08 and then tried to install the stock firmware via usb and it still hangs at 8%. I wonder if i try to install a different version?
I cannot boot from SD since my bottom keys dont work. I cannot click the call button to accept.
Click to expand...
Click to collapse
Don't you understand? You don't need the stock ROM, once you have the stock SPL you -should- be fine. Go to the tri-Color screen and download HSPL4 on your PC and run it and choose 3.03.0000 (not HSPL) and click next and it should flash. If you've done that then you're ready to send it off for warranty. No need for stock ROM. Just change the HSPL to SPL again which TMagnolia and I just told you how to do.
Oh yeah and you can easily get to the tri-color by plugging the USB in and holding the Vol down button.
Skellyyy said:
Don't you understand? You don't need the stock ROM, once you have the stock SPL you -should- be fine. Go to the tri-Color screen and download HSPL4 on your PC and run it and choose 3.03.0000 (not HSPL) and click next and it should flash. If you've done that then you're ready to send it off for warranty. No need for stock ROM. Just change the HSPL to SPL again which TMagnolia and I just told you how to do.
Click to expand...
Click to collapse
Awesome! Thank you, no I was not understanding...very new at this. Thank you!
Quick question to add... there is no rom on there at all now....do i need to install one for warrenty?
The green square still says "upgrade rom code error" please try again
They won't power the phone on to see if theres a ROM and if they do it'll boot to SPL in which case I'd say they'd flash a stock ROM. What green box?
Skellyyy said:
Don't you understand? You don't need the stock ROM, once you have the stock SPL you -should- be fine. Go to the tri-Color screen and download HSPL4 on your PC and run it and choose 3.03.0000 (not HSPL) and click next and it should flash. If you've done that then you're ready to send it off for warranty. No need for stock ROM. Just change the HSPL to SPL again which TMagnolia and I just told you how to do.
Click to expand...
Click to collapse
I think they do not have a stock ROM on the HD2 and I was stupid and did not realize they probably already had HSPL on thier HD2. So they are not good to go for warranty just yet.
At the OP try right clicking on the RUU and select run as administrator. Also try different USB ports too that might help.
Skellyyy said:
They won't power the phone on to see if theres a ROM and if they do it'll boot to SPL in which case I'd say they'd flash a stock ROM. What green box?
Click to expand...
Click to collapse
When you get the red green blue and white screen, the green section.
in the green section it says
Upgrade ROM code error
Please try again
If you just let the phone boot up, lit says "software update faild. please try again" on a black screen with triagle with a ! in it.
T-Macgnolia said:
I think they do not have a stock ROM on the HD2 and I was stupid and did not realize they probably already had HSPL on thier HD2. So they are not good to go for warranty just yet.
At the OP try right clicking on the RUU and select run as administrator. Also try different USB ports too that might help.
Click to expand...
Click to collapse
I am using the exe file that i downloaded off tmobiles site...is that what i should be using to flash?
Skellyyy said:
They won't power the phone on to see if theres a ROM and if they do it'll boot to SPL in which case I'd say they'd flash a stock ROM. What green box?
Click to expand...
Click to collapse
I would still try to get the stock ROM on the HD2 before sending it in cause I can assure you if they will turn the phome on and check the ROM and SPL. and if they have SPL 3.03.000 and not SPL 2.10.0000 they will say why iscthat cause it looks like they were tring to update the phone and sould not have SPL 3.03.0000. Then they will probably say they either did not preform the flash correctly or had un approved software on the phone and will not pass it as warranty.
bnd10706 said:
I am using the exe file that i downloaded off tmobiles site...is that what i should be using to flash?
Click to expand...
Click to collapse
Yes that is the RUU, right click it and select run as adminastrator, Skellyyy is right too you need to use the HSPL 4 Utility to reset your HSPL to SPL 3.03.0000 if you get the ROM to flash
Can anyone help me please... I'm trying to upgrade the rom to the latest HTC HD2 rom for O2. I connect the phone via USB, sync it and then run the RUU program from HTCs website. The phone starts the process and boots the phone to the 4 colour screen and then to the black HTC progress screen and then it hangs on 0% for a few minutes until the utility finally tells me its lost connection with the phone (Error 262). I've done soft resets and hard resets. Disabled firewalls. Tried on another machine. Even ran the utility under XP SP3 compatibility. Still no joy. Can anyone help?? Thanks
Sounds like you might have a bad USB cable or that you are having timing out problems. First forget about the ActiveSync. All ActiveSynce does is help insure hour HD2 is ready to be flash by checking the battery level and such. Power your HD2 on but hold the volume down button down while powering on. When you see the tri color bootloader screen connect hour USB cable and wait for the Serial in the white bar of bootloader to change to USB and then right click the RUU of the ROM and select run as administrator. If this still does not work I would try another USB cable.
T-Macgnolia said:
Sounds like you might have a bad USB cable or that you are having timing out problems. First forget about the ActiveSync. All ActiveSynce does is help insure hour HD2 is ready to be flash by checking the battery level and such. Power your HD2 on but hold the volume down button down while powering on. When you see the tri color bootloader screen connect hour USB cable and wait for the Serial in the white bar of bootloader to change to USB and then right click the RUU of the ROM and select run as administrator. If this still does not work I would try another USB cable.
Click to expand...
Click to collapse
Thanks for this... i followed your instruction and used 2 different cables. No joy.
Anything else I can try that doesn't involved the device suffering a sudden impact with the nearest wall??
Cheers
could it have anything to do with the phone being locked to O2... its the latest ROM for O2 that I'm trying to install.
mr_bacon said:
could it have anything to do with the phone being locked to O2... its the latest ROM for O2 that I'm trying to install.
Click to expand...
Click to collapse
hmm....if you are trying to flash stock rom which is not intended for your device, you need HSPL or Gold card.
There are threads in Windows Mobile 6.5 section that will guide you on installing HSPL or making a Gold Card.
Good luck
silverwind said:
hmm....if you are trying to flash stock rom which is not intended for your device, you need HSPL or Gold card.
There are threads in Windows Mobile 6.5 section that will guide you on installing HSPL or making a Gold Card.
Good luck
Click to expand...
Click to collapse
Well here's the thing, my phone is locked to O2. I'm trying to install the latest ROM from HTCs website for O2 customers. For the life of me I cant get it to install. I did install HSPL a few months ago when I tried to run Android from the SD card. That didnt work either. Like I say, I've done a hard reset. Could the HSPL thing be causing an issue. How do I get rid of it.
I hate being a noob sometimes!!
mr_bacon said:
Well here's the thing, my phone is locked to O2. I'm trying to install the latest ROM from HTCs website for O2 customers. For the life of me I cant get it to install. I did install HSPL a few months ago when I tried to run Android from the SD card. That didnt work either. Like I say, I've done a hard reset. Could the HSPL thing be causing an issue. How do I get rid of it.
I hate being a noob sometimes!!
Click to expand...
Click to collapse
To get rid of HSPL you just have to run the HSPL Utility avain and choose the correct SPL version for your ROM when it asks what version you want to flash. Remember HSPL has the stock SPL versions to, click on the link in my sig to download HSPL 4. Hint thecstock SPL versions all have four zeros at fhe end and the HSPL version do not.
You said you are getting error 262, this usually means you don't have the right SPL or HSPL one of the two atleast that is if I remember correctly. What ROM are you trying to flash and what does it say in bootloader right now?
T-Macgnolia said:
To get rid of HSPL you just have to run the HSPL Utility avain and choose the correct SPL version for your ROM when it asks what version you want to flash. Remember HSPL has the stock SPL versions to, click on the link in my sig to download HSPL 4. Hint thecstock SPL versions all have four zeros at fhe end and the HSPL version do not.
You said you are getting error 262, this usually means you don't have the right SPL or HSPL one of the two atleast that is if I remember correctly. What ROM are you trying to flash and what does it say in bootloader right now?
Click to expand...
Click to collapse
Hi... Been away so only just got this reply.
The rom I'm trying to install is a stock rom update from the HTC website:
O2 (UK): 3.14.206.1
For the record, my phone is an O2 phone.
As for Bootloader? It currently says:
PB81100 HX-BC
SPL-2.08.0000 8G XE
MicroP(LED) 0x05
MicroP(TOUCH) 0x40
Hope that helps. Really bugging the arse off me this is.
get hspl2,
put phone into bootloader manually first and connect usb lead
(thats why it was timing out on you ((error 262)) because the connection takes too long to reconnect when it reboots from winmo into bootloader, , if you do it yourself first, that solves this error 99% of the time.)
when 'serial' changes to 'usb' run hspl2, choose 1.66.0000 (i recommend this because 2.08.0000, whilst stock, is a tmous stock, so 'may' give problems, , totally unconfirmed, but i had issues recently removing android/magldr whilst spl was 2.08.0000, i switched to 1.66.0000 and it worked straight away, i have a slight hunch that spl 2 doesnt like to be downgraded in some circumstances, , if you preffer you could use hspl4 and go straight for 3.03.0000, since that is whjat your 3.14 rom will install anyway when you flash it)
when it reboots saying its done, immediately hold voldown to re-enter bootloader
when serial changes to usb, run your 3.14.exe
samsamuel said:
get hspl2,
put phone into bootloader manually first and connect usb lead
(thats why it was timing out on you ((error 262)) because the connection takes too long to reconnect when it reboots from winmo into bootloader, , if you do it yourself first, that solves this error 99% of the time.)
when 'serial' changes to 'usb' run hspl2, choose 1.66.0000 (i recommend this because 2.08.0000, whilst stock, is a tmous stock, so 'may' give problems, , totally unconfirmed, but i had issues recently removing android/magldr whilst spl was 2.08.0000, i switched to 1.66.0000 and it worked straight away, i have a slight hunch that spl 2 doesnt like to be downgraded in some circumstances, , if you preffer you could use hspl4 and go straight for 3.03.0000, since that is whjat your 3.14 rom will install anyway when you flash it)
when it reboots saying its done, immediately hold voldown to re-enter bootloader
when serial changes to usb, run your 3.14.exe
Click to expand...
Click to collapse
Thanks for this but can I ask a favour... Can you give me an 'idiot guide' as to what to do? I'm a compelete noob to this kind of thing and don't wanna brick my phone.
Cheers
mr_bacon said:
Thanks for this but can I ask a favour... Can you give me an 'idiot guide' as to what to do? I'm a compelete noob to this kind of thing and don't wanna brick my phone.
Cheers
Click to expand...
Click to collapse
Ignore that..
Mate - you're a genius. Followed your instructions and it worked like a charm.
Cheers pal. You saved my brain
Erm, not sure how much more basic i can make it. (Ignore my descriptions, just follow the steps)
Power off, hold voldown,power on keeping voldown held,, see multi striped coloured screen, that's bootloader, you can flash from this screen.
First you should try without bothering to change the spl.
Enter bootloader and connect USB, run the 3.14 you downloaded. That's it.
If it doesn't work, try changing spl as in my previous post by entering bootloader, and instead of running the 3.14 you run hspl instead.
As for writing a guide, you already read the various "how to flash.." guides (there are several) and watched the (also several) YouTube guides before you even started this thread,,, didn't you? Didn't you?? If not then shame on you!
Post back and ill check tomorrow.
Hi all,
I would like to ask someone who are willing to lend me a hand.
Here comes the problem:
1. I wanna flash a NAND Android into my HD2 (not Tmous)
2. I have already flashed with HSPL2 with selection of 2.08 HSPL.
3. It went through to Windows Mobile again, nothing goes wrong untill when I am trying to flash with Magldr Bootloader with ROM Update Utility.
4. It went through again, after that the phone reboot itself and it should be displaying Magldr bootloader instead of HTC green logo stuck at the WHITE SCREEN.
5. I've tried several ways to solve it including soft-reset but still nothing happen with the same problem which is the green HTC logo stuck at the white screen.
6. Even Hard-reset with factory default reset I have tried, the process went through, but still the same problem again (YOU GUYS KNOW WHAT I MEANT).
7. So, I tried another LeoAdvanceRUU.exe which @HD2Owner had posted few months ago, the flashing process worked through but it stucked at the 0% with HTC logo at BLACK screen.
8. I kept on trying with another ROM or Radio Flashing again, again and again and it is still stucked at 0% !!! (GOSH !! I'm going to be crazy)
I really hope someone can help me out of this as I am very appreciate to those who are willing to help me. I need the phone to deal with my daily usage, please the 'PRO's out there.. ><
Thanks in advance.
P/S: The Tri-Color mode showed PB8100 - SS-BC
Did bootloader show 'SPL2.08HSPL' (or something along those lines)?
Nigeldg said:
Did bootloader show 'SPL2.08HSPL' (or something along those lines)?
Click to expand...
Click to collapse
Yes !! It does showed..coz its already HSPL-ed..but i stil duno what is happening..
you havent yet flashed a correct radio. Non tmous radios (..51.. radios) wont allow magldr to start
enter bootloader
flash 2.15.50 radio
magldr will now start
I dont drink either LOL
samsamuel said:
you havent yet flashed a correct radio. Non tmous radios (..51.. radios) wont allow magldr to start
enter bootloader
flash 2.15.50 radio
magldr will now start
Click to expand...
Click to collapse
erm, I also tried to Flash the Radio ROM, but it will stucked at HTC logo with Black Screen and also 0% wont move either..
In that case double check the spl version in bootloader. Quite often people flash "2.08.0000" by mistake instead of "2.08.hspl"
(You did instal hspl before trying the radio, right? Radios news hspl too)
samsamuel said:
In that case double check the spl version in bootloader. Quite often people flash "2.08.0000" by mistake instead of "2.08.hspl"
(You did instal hspl before trying the radio, right? Radios news hspl too)
Click to expand...
Click to collapse
yea i did install the HSPL before flashing the radio and it is done with 2.08 HSPL
but what do u mean by Radios news HSPL?
when I am flashing the radio in the bootloader, I used the common flashing technique which is using the CustomRUU with the RUU_Signed.nbh file which contains Radio 2.14.50 and then the only the problem came out.
by means every ROM that I am trying to flash, It will still stuck at 0% Black Screen with HTC logo..
oops, radios NEED hspl , lol, darned predictive txt!
ok, so sounds more like usb timeout,
enter bootloader, connect usb, count to 5, run customruu.
If that still wont work, you can flash radios from sd, just like roms. Put teh ruu_signed.nbh onto sd card, renamed leoimg.nbh, reboot into bootloader, phone will see the .nbh and flash it.
samsamuel said:
oops, radios NEED hspl , lol, darned predictive txt!
ok, so sounds more like usb timeout,
enter bootloader, connect usb, count to 5, run customruu.
If that still wont work, you can flash radios from sd, just like roms. Put teh ruu_signed.nbh onto sd card, renamed leoimg.nbh, reboot into bootloader, phone will see the .nbh and flash it.
Click to expand...
Click to collapse
erm, is the flashing will do it automatically itself ?? because I am still not able to boot into whatever OS yet. And do i need to connect the USB when the leoimg.nbh flashing if its working itself ??
no, no usb needed, put the leoimg on the sd card, card into phone, power on phone holding voldown, bootloader finds the leoimg on the card and starts the flashing process.
eXcMichael said:
erm, is the flashing will do it automatically itself ?? because I am still not able to boot into whatever OS yet. And do i need to connect the USB when the leoimg.nbh flashing if its working itself ??
Click to expand...
Click to collapse
OK THAT'S WORKING @samsamuel !!!!!
THANKS ALOT !!!
I also assume the Radio was not flashed but i just cannot find a way to do the flash, and my troubleshooting was correct.
THANKS ALOT especially @samsauel and other devs' assistance. Highly Appreciate for what you guys contributed.. really THANK YOU, ITS NOW RUNNING Hyperdroid GBX ~
Thread can be closed and for further reference.
Look for HD2 nand toolkit 4.1 on XDA developers
It's a all in one utility hand HD2.
You can also try the we site addictive tips.com , they step by step tutorials.