Database Users

[Q] HELP: Have I bricked my HD2 by installing MAGLDR1.13?

Hi everyone! After checking the forum on possible quirks that can be encountered when installing MAGLDR I hope someone can help me with the following:
I am trying to install Android on the HD2 via full-NAND-flash (i.e. directly via USB without SD card). I read tons of webpages and I believe I understood the necessary steps. Check the SPL; Install Hspl; Install MAGLDR; etc.
I tried to install MAGLDR 1.13 and everything went nice and quick: 100% complete on the phone; 100% complete on the PC; click on finish; phone reboot .......... and now the HD2 does not go past the green-on-white HTC splash screen. No boot.
I can still acess the colour-striped bootloader, which reacts if I connect the USB cable. No more.
What have I done wrong? Can it be recovered?
Thanks in advance for any suggestion.

You need to do a bit more reading (it's fundamental). Flashing MAGLDR is only the first step in getting Android on NAND. Next, you'll need to flash CWM and if you're going to install Android, you are going to have to have an SD card.
It's clear you read enough to get as far as you have. I suggest doing a bit more.
Start here:
http://forum.xda-developers.com/showthread.php?t=905841

Thanks but I don't think I can do much more at this point. The phone seems to be stuck (see my initial post). Cheers,

Did you try holding the Red power button down while the phone was powering up? That should take you into the Magldr menu.
Also, since you say you can get into the bootloader, have you tried reflashing Magldr?

Yes, I did. However, in the flash window, where you should see you are going from ROM version X to ROM version Y, this information does not show. The flash process seems to go through normally but then the situation is the same one.
The bootloader I can access is the normal one, with the red-green-blue stripes: it shows:
PB81100 HX-BC
SPL-2.08.HSPL 8G XE
0x05
CotullaHSPL 0x30
On the bottom it reads "serial" and if I connect the USB cable it changes to "USB".

Do a task 29.
Flash radio 2.15
reflash magldr
Hope this helps

yz.hd said:
Flash radio 2.15
Click to expand...
Click to collapse
I think this is the case sensitive for the OP explained symptoms.
Flash 2.15 or any Radio Rom that supports 576MB.

I have used Task29+radio 2.15.50.14, the doloop file repackaged by shadrac.....
So in principle the radio should be the correct one.
Shall I try with the separate flashes? Would you please let me have the links to download them?
(beginning to despair.....)
Thanks

Use HD2 Toolkit to re-flash MAGLDR 1.13... easiest and most comprehensive tools.. If u still stuck, re-install WM ROM (better custom ROM since u want to install AD NAND) this w keep ur HSPL. Once u are back to WM, repeat the whole cycle use the kit (pls confirm ur Radio 2.xx.50.xx (above 2.07.50.xx) and not the .51.
gd luck

Norton 360 doesn't like the HD2 tkit...
Any idea why Norton 360 discards the download telling me the HD2 Toolkit is a threat? That's odd...... the download link comes from this very site.
Anyone else with the same experience? Cheers!

[Q] No Bootloader Menu after reboot

Hi folks,
I tried to flash my HTC HD2 for the first time. Read /watched different guides. In first 2 steps they were all the same:
- install HSPL
- instal MAGLDR
Done both, got positive responses on both.
BUT: after rebooting after installing MAGLDR I do not manage to get the bootloader screen. There´s just a white screen with green htc logo on it and nothing else happens.
Yes, I held the power button after reboot; about 1 min long. Nothing.
If I hold volume down button after reboot the stripey screen appears like after the HSPL installation. But there is also no menu.
Also tried to proceeed task29 with the HD2 Android NAND Toolkit. Got positive response there too and after this I begann from scratch. With the same results.
Does anyone have a clue what I made wrong or forgot?
Or a hint what to do now?
best regards
M.

What version hspl n magldr?
Sent from my LG-P999 using XDA App

and radio,
hspl MUST be 2.08.hspl ONLY
radio MUST be 2.xx.50.xx

Got hspl version 2.08.hspl from http://forum.xda-developers.com/showthread.php?t=611433
got MAGLDR version 1.13 from http://forum.xda-developers.com/showthread.php?t=893618
cant remember the full radio version but I checked it before starting and it fits to requirements.
But I´m a few steps forward...
Meanwhile I flashed the newest Original HTC HD Win Mobile 6.5 ROM so phone boots up again
After that I installed HSPL version 2.08.0000 (now I know that was a failure) an tried again to install MAGLDR. But the progress bar doesn´t move - neither on PC nor on phone...
So I first will try to install again HSPL like samsamuel said and try again with MAGLDR
[EDIT]
Radio Version is now 2.15.50.14

SOLVED
Don´t know why but after dooing all step again (after falshing new HTC ROM) all ist ok and android is booting...
I think something was not in expected version on my old ROM on the phone. Never made an update before. So I recommend to do this before starting with all other

MiMo99 said:
Don´t know why but after dooing all step again (after flashing new HTC ROM) all ist ok and android is booting...
I think something was not in expected version on my old ROM on the phone. Never made an update before. So I recommend to do this before starting with all other
Click to expand...
Click to collapse
the only regular hd2 stock rom that includes a magldr compatible radio is 3.14, so if the ''old rom'' you flashed was any other version, it will have also flashed a non magldr radio, which is why it happened. (I suspect).
Sorted now,

the same problem
Hi,
I have the same problem.
Just white screen with green HTC mark.
But I'm not shure how to flesh win mobile again, because I cannot connect my HTC HD2 via USB (PC doesn't recognise the phone).
tnx

Hey MiMo,
Could you please post links and steps to help myself and anyone else looking on how to fix this?
by links I mean can I have the stock rom you used and the radios and such
Thank you.

[Q] MAGLDR 1.13 stuck GO GO GO!

HI there so i bought a used HD2 wich came with ICS installed when it arrived i turned it on and loaded MAGLDR then it tried to load Android but got stuck at the GO GO GO! line. As i dont have any drivers installed and Windows doesnt recognize the HD2 in MAGLDR i cant flash a new rom. I wanted to do a Task 29 but that requires drivers too.
So my question is how do i perform a full wipe so i can get a working rom since the phone turns on, shows the TMobile splash screen then goes into Magldr and tries to boot android immediately then get sutck in GO GO GO!.

hold power button until magldr menu appear
in ad recovery you can wipe anything

Pentuni said:
HI there so i bought a used HD2 wich came with ICS installed when it arrived i turned it on and loaded MAGLDR then it tried to load Android but got stuck at the GO GO GO! line. As i dont have any drivers installed and Windows doesnt recognize the HD2 in MAGLDR i cant flash a new rom. I wanted to do a Task 29 but that requires drivers too.
So my question is how do i perform a full wipe so i can get a working rom since the phone turns on, shows the TMobile splash screen then goes into Magldr and tries to boot android immediately then get sutck in GO GO GO!.
Click to expand...
Click to collapse
good to know u want to start from scratch...u ll never know wats been put it that device... ....here is wat you can do
i had put out these steps in another thread to help out a fellow XDAian... try
files you need: (if you need pm me)
-task29
-Radio Leo 2.15.50.14
-DFT_LEO_MAGLDR113_DAF
-Recovery_150M_system_5M_cache
-rom zip (dont alter/extract zip if you done know wat to do with this)
do these: (from your current WP7 rom)
-restart device
-get into tricolor bootloader
-plug usb...hd2 should say 'USB'
-do a task 29
-get into bootloader again
-plug usb...hd2 should say 'USB'
-install radio by running 'CustomRUU.exe'
-get into tricolor bootloader
-plug usb...hd2 should say 'USB'
-run DAF.exe for installing MAGLDR
-reboot
-get into MAGLDR by holing power/end key while booting
-go to 'usb flasher' in the menu and press green/call button
-plug usb...hd2 should say 'USB'
-wait till it say 'wait usb...usb'
-get into your recovery folder
-run daf.exe
-reboot post completion
-get into MAGLDR by holing power/end key while booting
-get into ad-recovery
-get into mount storage
-activate usb mass storage
-now put the rom zip files into sd card
-press power to get back to recovery menu
-select install rom from sdcard
-choose rom file
-select install
this should typically install nandroid into your hd2...
if you face any issues, share the step and the error scenario/msg

I tried to get task29 but my PC doesn't recognize the hd2 even on bootloader.
Sent from my MB860 using xda premium
Edit: So i managed to get the drivers and got the phone recognized, so i performed task 29, worked perfectly. Followed the steps but when i try to install a radio it fails and gets stuck at 96%. I tried flashing the radio several times but no luck... What am i doing wrong?

It's better if you download the drivers because it's useful for later needs...
Best regards
Sam Razzy...
Sent from my HD2 using xda premium

Pentuni said:
Edit: So i managed to get the drivers and got the phone recognized, so i performed task 29, worked perfectly. Followed the steps but when i try to install a radio it fails and gets stuck at 96%. I tried flashing the radio several times but no luck... What am i doing wrong?
Click to expand...
Click to collapse
can u provide more details....actually as much details on the hd2 (eu/us), hspl, radio version, your process on how u tried etc...we will help you solve this.

gdsbalaji said:
can u provide more details....actually as much details on the hd2 (eu/us), hspl, radio version, your process on how u tried etc...we will help you solve this.
Click to expand...
Click to collapse
Their is a guide in my signature, its got basically everything you need to know. If you have problems post on there or pm me. I will gladly help.
Sent from my HD2 using xda premium

gdsbalaji said:
can u provide more details....actually as much details on the hd2 (eu/us), hspl, radio version, your process on how u tried etc...we will help you solve this.
Click to expand...
Click to collapse
I have the T Mobile US version, HSPL SPL-2.08.HSPL 8G XE COtullaHSPL 0x05 0x50(what it says on tricolor bootloader). The radio i tried to install is 2.15.50.14.
I got the drivers, my PC finally got a connection with the HD2 so i performed a task29 and wiped the phone then i followed your guide tried to install the radio but the process with CustomRUU.exe got stuck at 96% and said there was an error "this update utility can not be used on your device." and now the phone shows an Update Fail screen without a radio i cant install MAGLDr then install WP7 on it so what can i do?

kylew1212 said:
Their is a guide in my signature, its got basically everything you need to know. If you have problems post on there or pm me. I will gladly help.
Sent from my HD2 using xda premium
Click to expand...
Click to collapse
Thank you i read your guide. So can i instal clK without a radio? Also can i install ICS beta10 or Windows Phone 7 with cLK and witout going through the radio installation?
Another thing... the came with almost no battery and i cant charge the phone with the update failed screen i saw that i need at least 50% of battery but i dont think the phone has that much.

Pentuni said:
Thank you i read your guide. So can i instal clK without a radio? Also can i install ICS beta10 or Windows Phone 7 with cLK and witout going through the radio installation?
Another thing... the came with almost no battery and i cant charge the phone with the update failed screen i saw that i need at least 50% of battery but i dont think the phone has that much.
Click to expand...
Click to collapse
Okay sorry I should've explained more..
yes you have to have a radio.
Yes you can install ics beta 10 with clk.
No you cannot install wp7 with clk magldr is required for that.
If your phone is getting close to running out of battery I would flash clk 1.5 via SD card and then charge the phone up
Sent from my HD2 using xda premium

Ok so i got the radio installled and proceeded with the process with magldr installed fine and i followed this guide to get WP7.
http://forum.xda-developers.com/showthread.php?t=1246040
After the installation the phone syas reboot now! but doesnt do anything i had to pull out the battery and now it wont boot. ts stuck in a blank magldr menu.
EDIT: I managed to get magldr to show something, it tries to boot WPH but says 1eFATAL HIT 1. Did i scre up the installation? If i hold the power button it keeps doing the same thing without showing the options menu how do i wipe the rom so i can flash a new one?
Edit 2: flashed wp7 again boots magldr then sticks on GO GO GO! again.

I'm having the same problem until today.
Did a task29, installed magldr, cwm, then a rom, radio is 2.15.50.14.
It can boot to CWM, it can reinstall the rom but it's gets stuck in the go go go after restarting.
Please help
TIA

I know how to use magldr, but not tons about it.. also I think you guys should post in the wp forums someone there may be better help
Sent from my HD2 using xda premium

Pentuni said:
Ok so i got the radio installled and proceeded with the process with magldr installed fine and i followed this guide to get WP7.
http://forum.xda-developers.com/showthread.php?t=1246040
After the installation the phone syas reboot now! but doesnt do anything i had to pull out the battery and now it wont boot. ts stuck in a blank magldr menu.
EDIT: I managed to get magldr to show something, it tries to boot WPH but says 1eFATAL HIT 1. Did i scre up the installation? If i hold the power button it keeps doing the same thing without showing the options menu how do i wipe the rom so i can flash a new one?
Edit 2: flashed wp7 again boots magldr then sticks on GO GO GO! again.
Click to expand...
Click to collapse
Its happened to me before. Make sure as soon as you flash magldr, thats you clear mbr on sd card and use last 24 nand, and you will be fine, otherwise you will stay stuck on go go go go
good luck!

Yep.. thats a problem for you, but also for me, i have HTC HD2 fully working, just replaced digitzier soon, WinMo just works flawless thought it sucks ballls, and whenever i try to do task 29 then install radio then install magldr then install cwm with the required partition, i get stuck on GO GO GO! ..

[Q] Unable to boot to CLK - Stuck on HTC screen

Hi Team
Just bought an old HD2 from work and am trying to flash to Android via the method described here - http://forum.xda-developers.com/showthread.php?t=1402975
I get as far as the repartition step 13, and when the phone reboots it does not load into CLK fastboot. All that happens is the white HTC screen comes up and doesn't go any further. At this point the phone is not detectable via ADB or normal USB.
The phone is a GSM HD2 and has HSPL 2.08 installed.
Any help recovering this or pushing forward with the flash is much appreciated.

At step 13 you are in recovery trying to install the rom, it should be trying to boot the rom!
If you are in recovery then you have clk installed.
You might not have the correct partition size for your rom, it will not boot if the partition size is too small.
.

shanman-2 said:
At step 13 you are in recovery trying to install the rom, it should be trying to boot the rom!
If you are in recovery then you have clk installed.
You might not have the correct partition size for your rom, it will not boot if the partition size is too small.
.
Click to expand...
Click to collapse
Yeah thats the problem - it goes through the CLK partition/recovery install, and the phone goes from the tricolour screen to the HTC 0-100% screen, reboots and then the white HTC logo screen. From the instructions, I thought the phone would go straight into CLK recovery.
Is there a set of key presses I'm meant to do to trigger recovery?

You have to hold "home" while booting to boot into recovery.

jianC said:
You have to hold "home" while booting to boot into recovery.
Click to expand...
Click to collapse
Thanks mate - will give this a crack when I get home

stuartgr said:
Thanks mate - will give this a crack when I get home
Click to expand...
Click to collapse
Yeah didn't work - still goes to the HTC logo...im guessing this means CLK didn't install properly.....Any other ideas?

Do you have install radio 2.15.50.14 ?
Sent from my NexusHD2 using Tapatalk

You have to give us more information.
What does it say when you hold down the volume button when starting the device ?

Same poblem
I have the exact same problem... The clk bootloader doesn't start up when i press the home button, after i've flashed it, but instead getting stuck on the HTC-white screen. I also have another HD2 where i can flash android(NAND) etc... without problems, so i can't really see why it doesn't work..
Right now i've been using:
- HTC HD2 EU-version
- Radio: have tried 2.14.50.02 and 2.15.50.14 without succes...
- SPL - 2.08
- HPSL 4
I'm using the HD2 toolkit when i'm trying to flash the phone.
Please help..

You need HSPL 2.08 or 3.03 to install clk.
Sent from the pub...

shanman-2 said:
You need HSPL 2.08 or 3.03 to install clk.
Sent from the pub...
Click to expand...
Click to collapse
Thanks for response.
I've already have HSPL 2.08, just checked it up to make sure...
It's really strange, that my phone does have the right radio and HSPL, but still hangning up on the white HTC bootscreen, after i've flashed clk into it.. or it says that it had "succesfully flashed it"...
My steps for installing magldr or clk, tried both now.
1: Wipe task 29.
2: Flash HSPL 2.08
3: Flash Radio 2.15.50.1
5: Flash clk.
6: Hardreset.
7: Holding down homebutton.
8: Stuck on white screen... -.-'
---
This is what i have on my tricolor-screen
PB81100 HC - BC
SPL - 2.08. HPSL 8G XE
0X05
CotullaHSPL 0x40
---
Is there any kind of solution for this and have this happen for anyone before?

Have you installed cwm recovery?
Thats what your trying to get to holding the home button.
If it's not working after installing recovery go here and go to post three and try installing clk 1.5 using the leoimg.nbh method.
edit: clk 1.5 comes with recovery pre-installed.

shanman-2 said:
Have you installed cwm recovery?
Thats what your trying to get to holding the home button.
If it's not working after installing recovery go here and go to post three and try installing clk 1.5 using the leoimg.nbh method.
edit: clk 1.5 comes with recovery pre-installed.
Click to expand...
Click to collapse
Thanks for response.
Just tried the sd leoimg.nbh method, but still getting stuck on HTC-white...
:crying:

two2tee said:
Thanks for response.
I've already have HSPL 2.08, just checked it up to make sure...
It's really strange, that my phone does have the right radio and HSPL, but still hangning up on the white HTC bootscreen, after i've flashed clk into it.. or it says that it had "succesfully flashed it"...
My steps for installing magldr or clk, tried both now.
1: Wipe task 29.
2: Flash HSPL 2.08
3: Flash Radio 2.15.50.1
5: Flash clk.
6: Hardreset.
7: Holding down homebutton.
8: Stuck on white screen... -.-'
---
This is what i have on my tricolor-screen
PB81100 HC - BC
SPL - 2.08. HPSL 8G XE
0X05
CotullaHSPL 0x40
---
Is there any kind of solution for this and have this happen for anyone before?
Click to expand...
Click to collapse
two2tee said:
Thanks for response.
Just tried the sd leoimg.nbh method, but still getting stuck on HTC-white...
:crying:
Click to expand...
Click to collapse
Hold the back button while powering on to get to clk, you can boot to recovery from there and then install rom...
If you get to clk don't forgrt to partition your nand through settings menu..resize partitions...

shanman-2 said:
Hold the back button while powering on to get to clk, you can boot to recovery from there and then install rom...
If you get to clk don't forgrt to partition your nand through settings menu..resize partitions...
Click to expand...
Click to collapse
Thanks for response, but it seems like it doesn't even boot clk.. Normally when you've flashed clk, the phone should reboot to a black screen with some text and from here you can flash cwm recovery. But in this case, the black screen doesn't even show up.
Could it be that my phone have some hardware faults, or maybe is my HD2 not compatible with the radio (2.15.50.14) which were recommended?
Anyway, is there some way to see if clk has been flashed properly, just to make sure that it's there?

two2tee said:
Thanks for response, but it seems like it doesn't even boot clk.. Normally when you've flashed clk, the phone should reboot to a black screen with some text and from here you can flash cwm recovery. But in this case, the black screen doesn't even show up.
Could it be that my phone have some hardware faults, or maybe is my HD2 not compatible with the radio (2.15.50.14) which were recommended?
Anyway, is there some way to see if clk has been flashed properly, just to make sure that it's there?
Click to expand...
Click to collapse
The radio is fine for all versions of hd2 and is what I have on my EU version. All I can say is to start from scratch ie. Install hspl 2.08, radio, task 29, then install clk 1.5 again.
In that order...
Sent from the pub...

shanman-2 said:
The radio is fine for all versions of hd2 and is what I have on my EU version. All I can say is to start from scratch ie. Install hspl 2.08, radio, task 29, then install clk 1.5 again.
In that order...
Sent from the pub...
Click to expand...
Click to collapse
Still doesn't solve the problem. I have tried with various kind of orders, but without luck.
Just made a recheck on everything and i can conclude that HSPL 2.08 and the radio 2.15.50.1 is there.
The problem may not be a wrong HSPL or radio, since it's there, but perhaps it might be the phone that doesn't flash clk proberly...
Im really confused right now
Anyway, i've also tried to install magdlr but still ended up on HTC-white screen -.-'

two2tee said:
Still doesn't solve the problem. I have tried with various kind of orders, but without luck.
Just made a recheck on everything and i can conclude that HSPL 2.08 and the radio 2.15.50.1 is there.
The problem may not be a wrong HSPL or radio, since it's there, but perhaps it might be the phone that doesn't flash clk proberly...
Im really confused right now
Anyway, i've also tried to install magdlr but still ended up on HTC-white screen -.-'
Click to expand...
Click to collapse
Really don,t know what to say, looks like a jtag...

shanman-2 said:
Really don,t know what to say, looks like a jtag...
Click to expand...
Click to collapse
Hmm i could flash a custom win6.5 rom without problem...Could that help us on our way or?
EDIT: Just to be more precise, i've used "Artemis HD2 v70.0"
Link:
http://forum.xda-developers.com/showthread.php?t=612580

Well if you can do that it's not a jtag.
Probably be better to go back to stock if all else fails.
Sent from the pub...

[Q] Error while booting to CLK recovery

Hello
I just flashed CLK on my hd2 using the toolkit, I also flashed the toolkit recovery (which i believe was v 4.3)
Now when I try to boot to recovery using Home + red buttons I get this error in the middle of the command lines
"ERROR: CANNOT READ RECOVERY_HEADER"
I tried to wipe all and reflash everything again but I keep getting the same error.
I looked everywhere but can't find any answer.
Is there any other way I can install a new ROM without accessing the CWM? like using the command prompt.
I also attached a screenshot of the error.
Any help would be very much appreciate it. and Please if there is a solution please show the steps for it cuz I am still new with CLK.

The latest stable version of clk is v1.5 which also installs a version of cwm , there is even one that installs twrp recovery too!
No links on my phone but will be easy to find...
BTW did you select clk install recovery option after clk reparation?
Sent from my NexusHD2 using xda premium

shanman-2 said:
The latest stable version of clk is v1.5 which also installs a version of cwm , there is even one that installs twrp recovery too!
No links on my phone but will be easy to find...
BTW did you select clk install recovery option after clk reparation?
Sent from my NexusHD2 using xda premium
Click to expand...
Click to collapse
I installed clk v1.5.1.1 just now but the phone freezed on "stick together" screen. any other way?

What does it say on the boot loader screen?
how did you Install? All steps you took?
Sent from my NexusHD2 using xda premium

shanman-2 said:
What does it say on the boot loader screen?
how did you Install? All steps you took?
Sent from my NexusHD2 using xda premium
Click to expand...
Click to collapse
I downloaded this file provided in clk thread "black_lk_20120920-TouchRec_b8" I installed it using the toolkit, I then added the LEOIMG file to the toolkit and flashed it.
And I can't get to the boot loader screen, I get the "stick together" screen once I turn on the phone, and then it freezes.

mjody said:
I downloaded this file provided in clk thread "black_lk_20120920-TouchRec_b8" I installed it using the toolkit, I then added the LEOIMG file to the toolkit and flashed it.
And I can't get to the boot loader screen, I get the "stick together" screen once I turn on the phone, and then it freezes.
Click to expand...
Click to collapse
Hold the volume down button and power on the device is not working ?????
Edit: what LEOIMG file???

shanman-2 said:
Hold the volume down button and power on the device is not working ?????
Edit: what LEOIMG file???
Click to expand...
Click to collapse
UPDATE! Ok I think I didn't install the right file earlier but I just downloaded the clk from here:
http://forum.xda-developers.com/showpost.php?p=21608340&postcount=848
it boots fine to the clk first screen. which I will add a picture of.
but It gives me this message when I select recovery. (Also a picture added)
ps: thank you very much for keeping up with me so fast.

mjody said:
UPDATE! Ok I think I didn't install the right file earlier but I just downloaded the clk from here:
http://forum.xda-developers.com/showpost.php?p=21608340&postcount=848
it boots fine to the clk first screen. which I will add a picture of.
but It gives me this message when I select recovery. (Also a picture added)
ps: thank you very much for keeping up with me so fast.
Click to expand...
Click to collapse
What version of hspl do you have installed?
If it's hspl 2.08 or hspl 3.03 try this,
first do a task29 using the toolkit
Then place the LEOIMG.nbh file on the root of your sdcard.
Now power on the device while holding the volume down button.
When asked to proceed with install push the power button..
This should install clk 1.5 with a default partition size which you can change from within clk later!
Let me know if it works.

shanman-2 said:
What version of hspl do you have installed?
If it's hspl 2.08 or hspl 3.03 try this,
first do a task29 using the toolkit
Then place the LEOIMG.nbh file on the root of your sdcard.
Now power on the device while holding the volume down button.
When asked to proceed with install push the power button..
This should install clk 1.5 with a default partition size which you can change from within clk later!
Let me know if it works.
Click to expand...
Click to collapse
I tried flashing it that way but it doesn't work with me, when I press volume down button with power it only shows the multicolored screen.
I also tried to restore the stock rom, by installing the rom from TMOUS website, my phone also freezes on the firs boot screen, "Stick Together"
by looking at this thread, http://forum.xda-developers.com/showthread.php?t=1063807
I think I got a hardware issue, RIP my hd2

mjody said:
I tried flashing it that way but it doesn't work with me, when I press volume down button with power it only shows the multicolored screen.
I also tried to restore the stock rom, by installing the rom from TMOUS website, my phone also freezes on the firs boot screen, "Stick Together"
by looking at this thread, http://forum.xda-developers.com/showthread.php?t=1063807
I think I got a hardware issue, RIP my hd2
Click to expand...
Click to collapse
Maybe so.
What way did you flash stock rom?
I don't understand why you cannot flash clk from the sdcard!
Have you tried a different sdcard??
What version of hspl do you have on that multicolored screen if you have anything?????
Edit:Hey, I hit the thanks by mistake but wtf, welcome to xda! :laugh:

shanman-2 said:
Maybe so.
What way did you flash stock rom?
I don't understand why you cannot flash clk from the sdcard!
Have you tried a different sdcard??
What version of hspl do you have on that multicolored screen if you have anything?????
Edit:Hey, I hit the thanks by mistake but wtf, welcome to xda! :laugh:
Click to expand...
Click to collapse
I did task29 then downloaded the rom file from t-mobile webisite then put phone on multicolored with usb debugging and ran the file on my computer.
I actually had this phone for almost 3 years now and I flashed about 4 different versions of android but i was using mgldr.
the phone was doing great with me but about 4 days I wanted to go to recovery to back up the phone I got "1E FATAL HIT 1"
I read that some one had the same issue and they switched to clk and it worked fine, and someone flashed stock rom then custom and it worked.
but nothing is working with me, I have 2.08 hspl and I've been using that for a long time, I tried 3 sdcards using both ways of flashing (toolkit and putting LEOIMG file in the sdcard) but it failed in all of them.
PS: thank you for the thank though I have been here since I got the phone and never got one thanks haha.

mjody said:
I did task29 then downloaded the rom file from t-mobile webisite then put phone on multicolored with usb debugging and ran the file on my computer.
I actually had this phone for almost 3 years now and I flashed about 4 different versions of android but i was using mgldr.
the phone was doing great with me but about 4 days I wanted to go to recovery to back up the phone I got "1E FATAL HIT 1"
I read that some one had the same issue and they switched to clk and it worked fine, and someone flashed stock rom then custom and it worked.
but nothing is working with me, I have 2.08 hspl and I've been using that for a long time, I tried 3 sdcards using both ways of flashing (toolkit and putting LEOIMG file in the sdcard) but it failed in all of them.
PS: thank you for the thank though I have been here since I got the phone and never got one thanks haha.
Click to expand...
Click to collapse
I don't understand why you cannot flash clk from the sdcard!
Click to expand...
Click to collapse
Now I do, I think!
I have asked you what it says on the multicolored screen a few times.
Pic please?
Flashing stock rom should do the trick as regards verifying that it's not a hardware problem, but it will have wiped your hspl!
So to install clk v1.5, you will have to re-flash hspl 2.08 (no zeros after the 8) or hspl 3.03!

shanman-2 said:
Now I do, I think!
I have asked you what it says on the multicolored screen a few times.
Pic please?
Flashing stock rom should do the trick as regards verifying that it's not a hardware problem, but it will have wiped your hspl!
So to install clk v1.5, you will have to re-flash hspl 2.08 (no zeros after the 8) or hspl 3.03!
Click to expand...
Click to collapse
Sorry for that, here is a picture of what you need. And this picture is while I have the stock rom installed on the phone now.
I tired to install clk 1.5 before flashing stock rom.

mjody said:
Sorry for that, here is a picture of what you need. And this picture is while I have the stock rom installed on the phone now.
I tired to install clk 1.5 before flashing stock rom.
Click to expand...
Click to collapse
OK, I would not give up yet.
Re-install hspl and this time select "3.03", then task 29 and try to reinstall clk 1.5...
Edit: If the last thing you did was install stock it won't work with hspl installed,
It should say something like..SPL-2.08.0000, use the hspl 3.03 package to downgrade to this spl version and then install stock from pc as normal (MAKE SURE you are using the correct stock rom for your phone) or as I said, try the above...

shanman-2 said:
OK, I would not give up yet.
Re-install hspl and this time select "3.03", then task 29 and try to reinstall clk 1.5...
Edit: If the last thing you did was install stock it won't work with hspl installed,
It should say something like..SPL-2.08.0000, use the hspl 3.03 package to downgrade to this spl version and then install stock from pc as normal (MAKE SURE you are using the correct stock rom for your phone) or as I said, try the above...
Click to expand...
Click to collapse
I am getting really frustrated now!
for clk:
I upgraded the hspl to 3.03, then installed clk 1.5. UNFORTUNATELY I am still getting the same message when I boot into recovery.
for stock rom: (I got it from t-mobile website which is the right one for my phone)
after failing to install clk, I FIRST downgraded the hspl to SPL 3.03.0000 and tried to flash the stock rom but the percentage bar doesn't even move. So I decided to try it with 2.08.0000 but the same thing happens. This doesn't happen when I have 3.03.HSPL or 2.08.HSPL, it actually loads when I have the hspl but then when it is done, I get stuck in "stick together" screen.

mjody said:
I am getting really frustrated now!
for clk:
I upgraded the hspl to 3.03, then installed clk 1.5. UNFORTUNATELY I am still getting the same message when I boot into recovery.
for stock rom: (I got it from t-mobile website which is the right one for my phone)
after failing to install clk, I FIRST downgraded the hspl to SPL 3.03.0000 and tried to flash the stock rom but the percentage bar doesn't even move. So I decided to try it with 2.08.0000 but the same thing happens. This doesn't happen when I have 3.03.HSPL or 2.08.HSPL, it actually loads when I have the hspl but then when it is done, I get stuck in "stick together" screen.
Click to expand...
Click to collapse
Have you tried this it's about the only option left...
I knew I had seen that thread before somewhere..
Maybe someone else has an idea, samsamuel might swing by but worth trying the above anyway...
best of luck

shanman-2 said:
Have you tried this it's about the only option left...
I knew I had seen that thread before somewhere..
Maybe someone else has an idea, samsamuel might swing by but worth trying the above anyway...
best of luck
Click to expand...
Click to collapse
It is not working! I took off the battery and back on and kept holding the restore button like 10 times.
Ugh I got a headache working on this for a week.
Thank you for your help man! and I hope someone can find out what the heck is wrong with my phone.