HI there so i bought a used HD2 wich came with ICS installed when it arrived i turned it on and loaded MAGLDR then it tried to load Android but got stuck at the GO GO GO! line. As i dont have any drivers installed and Windows doesnt recognize the HD2 in MAGLDR i cant flash a new rom. I wanted to do a Task 29 but that requires drivers too.
So my question is how do i perform a full wipe so i can get a working rom since the phone turns on, shows the TMobile splash screen then goes into Magldr and tries to boot android immediately then get sutck in GO GO GO!.
hold power button until magldr menu appear
in ad recovery you can wipe anything
Pentuni said:
HI there so i bought a used HD2 wich came with ICS installed when it arrived i turned it on and loaded MAGLDR then it tried to load Android but got stuck at the GO GO GO! line. As i dont have any drivers installed and Windows doesnt recognize the HD2 in MAGLDR i cant flash a new rom. I wanted to do a Task 29 but that requires drivers too.
So my question is how do i perform a full wipe so i can get a working rom since the phone turns on, shows the TMobile splash screen then goes into Magldr and tries to boot android immediately then get sutck in GO GO GO!.
Click to expand...
Click to collapse
good to know u want to start from scratch...u ll never know wats been put it that device... ....here is wat you can do
i had put out these steps in another thread to help out a fellow XDAian... try
files you need: (if you need pm me)
-task29
-Radio Leo 2.15.50.14
-DFT_LEO_MAGLDR113_DAF
-Recovery_150M_system_5M_cache
-rom zip (dont alter/extract zip if you done know wat to do with this)
do these: (from your current WP7 rom)
-restart device
-get into tricolor bootloader
-plug usb...hd2 should say 'USB'
-do a task 29
-get into bootloader again
-plug usb...hd2 should say 'USB'
-install radio by running 'CustomRUU.exe'
-get into tricolor bootloader
-plug usb...hd2 should say 'USB'
-run DAF.exe for installing MAGLDR
-reboot
-get into MAGLDR by holing power/end key while booting
-go to 'usb flasher' in the menu and press green/call button
-plug usb...hd2 should say 'USB'
-wait till it say 'wait usb...usb'
-get into your recovery folder
-run daf.exe
-reboot post completion
-get into MAGLDR by holing power/end key while booting
-get into ad-recovery
-get into mount storage
-activate usb mass storage
-now put the rom zip files into sd card
-press power to get back to recovery menu
-select install rom from sdcard
-choose rom file
-select install
this should typically install nandroid into your hd2...
if you face any issues, share the step and the error scenario/msg
I tried to get task29 but my PC doesn't recognize the hd2 even on bootloader.
Sent from my MB860 using xda premium
Edit: So i managed to get the drivers and got the phone recognized, so i performed task 29, worked perfectly. Followed the steps but when i try to install a radio it fails and gets stuck at 96%. I tried flashing the radio several times but no luck... What am i doing wrong?
It's better if you download the drivers because it's useful for later needs...
Best regards
Sam Razzy...
Sent from my HD2 using xda premium
Pentuni said:
Edit: So i managed to get the drivers and got the phone recognized, so i performed task 29, worked perfectly. Followed the steps but when i try to install a radio it fails and gets stuck at 96%. I tried flashing the radio several times but no luck... What am i doing wrong?
Click to expand...
Click to collapse
can u provide more details....actually as much details on the hd2 (eu/us), hspl, radio version, your process on how u tried etc...we will help you solve this.
gdsbalaji said:
can u provide more details....actually as much details on the hd2 (eu/us), hspl, radio version, your process on how u tried etc...we will help you solve this.
Click to expand...
Click to collapse
Their is a guide in my signature, its got basically everything you need to know. If you have problems post on there or pm me. I will gladly help.
Sent from my HD2 using xda premium
gdsbalaji said:
can u provide more details....actually as much details on the hd2 (eu/us), hspl, radio version, your process on how u tried etc...we will help you solve this.
Click to expand...
Click to collapse
I have the T Mobile US version, HSPL SPL-2.08.HSPL 8G XE COtullaHSPL 0x05 0x50(what it says on tricolor bootloader). The radio i tried to install is 2.15.50.14.
I got the drivers, my PC finally got a connection with the HD2 so i performed a task29 and wiped the phone then i followed your guide tried to install the radio but the process with CustomRUU.exe got stuck at 96% and said there was an error "this update utility can not be used on your device." and now the phone shows an Update Fail screen without a radio i cant install MAGLDr then install WP7 on it so what can i do?
kylew1212 said:
Their is a guide in my signature, its got basically everything you need to know. If you have problems post on there or pm me. I will gladly help.
Sent from my HD2 using xda premium
Click to expand...
Click to collapse
Thank you i read your guide. So can i instal clK without a radio? Also can i install ICS beta10 or Windows Phone 7 with cLK and witout going through the radio installation?
Another thing... the came with almost no battery and i cant charge the phone with the update failed screen i saw that i need at least 50% of battery but i dont think the phone has that much.
Pentuni said:
Thank you i read your guide. So can i instal clK without a radio? Also can i install ICS beta10 or Windows Phone 7 with cLK and witout going through the radio installation?
Another thing... the came with almost no battery and i cant charge the phone with the update failed screen i saw that i need at least 50% of battery but i dont think the phone has that much.
Click to expand...
Click to collapse
Okay sorry I should've explained more..
yes you have to have a radio.
Yes you can install ics beta 10 with clk.
No you cannot install wp7 with clk magldr is required for that.
If your phone is getting close to running out of battery I would flash clk 1.5 via SD card and then charge the phone up
Sent from my HD2 using xda premium
Ok so i got the radio installled and proceeded with the process with magldr installed fine and i followed this guide to get WP7.
http://forum.xda-developers.com/showthread.php?t=1246040
After the installation the phone syas reboot now! but doesnt do anything i had to pull out the battery and now it wont boot. ts stuck in a blank magldr menu.
EDIT: I managed to get magldr to show something, it tries to boot WPH but says 1eFATAL HIT 1. Did i scre up the installation? If i hold the power button it keeps doing the same thing without showing the options menu how do i wipe the rom so i can flash a new one?
Edit 2: flashed wp7 again boots magldr then sticks on GO GO GO! again.
I'm having the same problem until today.
Did a task29, installed magldr, cwm, then a rom, radio is 2.15.50.14.
It can boot to CWM, it can reinstall the rom but it's gets stuck in the go go go after restarting.
Please help
TIA
I know how to use magldr, but not tons about it.. also I think you guys should post in the wp forums someone there may be better help
Sent from my HD2 using xda premium
Pentuni said:
Ok so i got the radio installled and proceeded with the process with magldr installed fine and i followed this guide to get WP7.
http://forum.xda-developers.com/showthread.php?t=1246040
After the installation the phone syas reboot now! but doesnt do anything i had to pull out the battery and now it wont boot. ts stuck in a blank magldr menu.
EDIT: I managed to get magldr to show something, it tries to boot WPH but says 1eFATAL HIT 1. Did i scre up the installation? If i hold the power button it keeps doing the same thing without showing the options menu how do i wipe the rom so i can flash a new one?
Edit 2: flashed wp7 again boots magldr then sticks on GO GO GO! again.
Click to expand...
Click to collapse
Its happened to me before. Make sure as soon as you flash magldr, thats you clear mbr on sd card and use last 24 nand, and you will be fine, otherwise you will stay stuck on go go go go
good luck!
Yep.. thats a problem for you, but also for me, i have HTC HD2 fully working, just replaced digitzier soon, WinMo just works flawless thought it sucks ballls, and whenever i try to do task 29 then install radio then install magldr then install cwm with the required partition, i get stuck on GO GO GO! ..
Related
Hi
after i flashed my HD2 with MAGLDR, it doesnt boot anymore!!!
Can some one help me? I cannot connect it to my laptop to flash ist again. Is there a way to get directly in the USB-modus?
Help me please!!!
Jigsaw8989 said:
Hi
after i flashed my HD2 with MAGLDR, it doesnt boot anymore!!!
Can some one help me? I cannot connect it to my laptop to flash ist again. Is there a way to get directly in the USB-modus?
Help me please!!!
Click to expand...
Click to collapse
did you use HSPL before it ??
i flashed it several times before with HSpl but this is the first time it went worg is there something i can do?
Jigsaw8989 said:
i flashed it several times before with HSpl but this is the first time it went worg is there something i can do?
Click to expand...
Click to collapse
do you have HardSPL 2.08 ??? because in magldr thread it is written as required
1. Wrong section -> There's a Magldr topic, search for it.
2. First read, then act?
Have you installed a rom yet? Does the phone boot to Magldr? A little more info is useful..
Booting into bootloader via: turn on the phone, hold volume down key while booting
Booting into Magldr: turn on the phone and keep the power button pressed down untill Magldr comes up.
Not sure...
Its possilbe that i didn´t update it to 2.08. I think i have got 1.42 but im not sure. If I only could connect my phone to my laptop...
Jigsaw8989 said:
Its possilbe that i didn´t update it to 2.08. I think i have got 1.42 but im not sure. If I only could connect my phone to my laptop...
Click to expand...
Click to collapse
Can you get to 3 color screen where it writes hspl version etc. ?? if yes try to install HSPL 2.08 and then the magldr
I have got 1.42. (i think that the problem! Im able to get in the boot loader but not to MAGLDR . I dont hava a NAND version of andird on my phone but i have got a Windows moble rom on it. Is there a possiblity to bot the WM throgh the bootloader that would be all i need!
im able to get in the bootloader (3 colourd screen) but how should I be able to install a new HSPL without a connection to my Mobile device center?
Do it within this way:
1. Make sure you have HSPL 2.08 installed
2. Install TASK29. If you need it search for this.
3. Install "RUU_Leo_S_HTC_WWE_3.14.405.2_Radio_15.42.50.11U_2.15.50.14_LEO_S_Ship.exe" on your device. Do some settings within Windows and SHUTDOWN!!!
4. Press VOL-Down and press POWER ON until you will see the flash boot screen.
5. Now install MAGLDR 1.13 (v. 250MB Edition)
6. IF THIS FAILS - install Windows AGAIN and after all install MAGLDR 1.13 WITHOUT Task29.
Yesterday I have done a complete reset. Installed my O2 firmware and replaced my original bootblock. After all I have had the same problem that MAGLDR won't install on this device. I have tried it with 1.12 and 1.13. NOTHING, device boot until the WHITE HTC logo and nothing more. But ANDROID was installed bevore.
After that procedure I was able to flash MAGLDR 1.13 again.
thanks for your help imm try to do anything you have told me! I flashed HSPL 2.08 and Magldr also started. Thankl so much for your Help. Now i will try to install DiserZ andrid rom!
How is it possible to boot windows with MAGLDR? and how is it possible to remove MAGLDR?
If you want boot WINDOWS ONLY: you don't need MAGLDR.
If you want to delete MAGLDR: just use Task29 ROM.
If you want restore all to default:
1. Download your ORIGINAL ROM from your Provider or HTC.
2. Use 7zip and unpack the EXE file.
3. Search the file "RUU_signed.nbh" and rename it to "leoimg.nbh".
4. Format your SD Card with FAT32 format
5. Copy the "leoimg.nbh" to the SDCARD.
6. Insert Card into your device.
Now search the RESET button right next to the SDCARD slot on the back of your device:
7. Press the RESET button AND VOL-Down and when you see within the display "LOADING..." RELEASE both immediately and follow the instructions on the screen. It might be that you need 2 or 3 times until you got it
!!!! EVERYTHING !!! on your device will be erased after all. If you get an error that you are not able to flash "...bla, bla, bla..." don't cry - just download your OFFICIAL ROM by device serial number on the HTC website.
Unpack this EXE (again), rename the *.nb0 file and just do it again.
hi,
MAGLDR doesn't recognize my sd card . i can't use usb mass storage , AD SD => CWM . apparently all the roms i want are released az ZIPs ...
is there a fix for that ?
Are you using magldr 1.13? If so you need to use the new CWM 1.3 partitions which now installs the partition onto NAND, so to use CWM you need to boot into the AD Recovery option from menu and not Boot AD SD. There is also no need to copy files to root of sd card.
There is a problem with magldr usb mass storage, but if you boot to CWM, select mount and storage and the usb storage you can copy perfectly.
hi
my problem is with the bootloader screen. After installing magldr 1.13 i could not start the ppc in bootloader mode. i have tried many key combinations and etc.. but it is still starting with magldr after a short white htc screen. So now i cannot load any official or custom winmo firmware. None of the android nand fw are working. Now i only can use winphone 7 with limited abilities.. Can anyone tell me the way to solve this and go back to original rom?
thanks
exxx80 said:
hi
my problem is with the bootloader screen. After installing magldr 1.13 i could not start the ppc in bootloader mode. i have tried many key combinations and etc.. but it is still starting with magldr after a short white htc screen. So now i cannot load any official or custom winmo firmware. None of the android nand fw are working. Now i only can use winphone 7 with limited abilities.. Can anyone tell me the way to solve this and go back to original rom?
thanks
Click to expand...
Click to collapse
When you say you can not start in bootloader, bootloader is started by turning the phone off, holding in the vol down button only and turning on the phone.
The phone should not even get to the white htc screen.
If you get into the tri-colour screen you can get back to a stock rom to start again.
waspsl said:
When you say you can not start in bootloader, bootloader is started by turning the phone off, holding in the vol down button only and turning on the phone.
The phone should not even get to the white htc screen.
If you get into the tri-colour screen you can get back to a stock rom to start again.
Click to expand...
Click to collapse
Yes exactly thats what i m doing. But it passes to magldr. I even have reset from the red button at the back but no way to bootloader
@ClydeB1 : so i have to install the new CWM using the USB Flasher and it'll boot from AD Recovery ? thats good news i guess ...
will it let me install ZIP roms ? also i have a 512Leo . why would i (or anyone) want to partition NAND ?!?
MTN_HD2 said:
@ClydeB1 : so i have to install the new CWM using the USB Flasher and it'll boot from AD Recovery ? thats good news i guess ...
will it let me install ZIP roms ? also i have a 512Leo . why would i (or anyone) want to partition NAND ?!?
Click to expand...
Click to collapse
Yes, install the appropriate cwm partition by going to usb flasher and running daf.exe. Then the phone will reboot to magldr, select AD recovery and you can then flash zip roms or updates, backup etc etc etc.... I have a 512 device also, so no problems.
I guess one of the reasons for running recovery off NAND is that not all users could get the sd based recovery to work.
exxx80 said:
hi
my problem is with the bootloader screen. After installing magldr 1.13 i could not start the ppc in bootloader mode. i have tried many key combinations and etc.. but it is still starting with magldr after a short white htc screen. So now i cannot load any official or custom winmo firmware. None of the android nand fw are working. Now i only can use winphone 7 with limited abilities.. Can anyone tell me the way to solve this and go back to original rom?
thanks
Click to expand...
Click to collapse
I have the same problem here. I tried to return from my NAND Android Builts to a Windows 6.5 ROM. But after Flashing, the reboot got stuck at the logo. I tried flashing over and over again, different WinRoms, reflashed MAGLDR and even tried a combination with HSPL. nothing seems to work. I dont pass the logo, cannot enter MAGLDR or load a normal build. I kinda run out of all my magic. anyone got any suggestions?
fastscorpion2010 said:
I have the same problem here. I tried to return from my NAND Android Builts to a Windows 6.5 ROM. But after Flashing, the reboot got stuck at the logo. I tried flashing over and over again, different WinRoms, reflashed MAGLDR and even tried a combination with HSPL. nothing seems to work. I dont pass the logo, cannot enter MAGLDR or load a normal build. I kinda run out of all my magic. anyone got any suggestions?
Click to expand...
Click to collapse
What hspl version and radio are you using? To use magldr you need 2.08.hspl and radio 2.08.50.xx or higher .50 radio
I'm not sure why it would hang on reflash to winmo, but let's try get to Android.
Hi!
I am using the SPL 2.08 and When i am installing the MAGLDR111 or MAGLDR113 it's Stop in 0%
How i can install the MAGLDR?
grisantycosme said:
Hi!
I am using the SPL 2.08 and When i am installing the MAGLDR111 or MAGLDR113 it's Stop in 0%
How i can install the MAGLDR?
Click to expand...
Click to collapse
you're using Stock SPL, you need Hard SPL (HSPL)
ClydeB1 said:
Are you using magldr 1.13? If so you need to use the new CWM 1.3 partitions which now installs the partition onto NAND, so to use CWM you need to boot into the AD Recovery option from menu and not Boot AD SD. There is also no need to copy files to root of sd card.
There is a problem with magldr usb mass storage, but if you boot to CWM, select mount and storage and the usb storage you can copy perfectly.
Click to expand...
Click to collapse
You...so...rock!
I've been getting utterly frustrated with watching Windows bars filling only halfway, but your solution worked like a charm!
:good: x many!
magldr problem
hi
i was instaling the magldr on my htc hd2, but during the instalation i realise that my VOLUME UP and DOWN buttons are broken and dont work...i have to choose some option in MAGLDR but i cant...so i'm stuck here, my phone boots only MAGLDR even when i restart the phone from the red button, or even when i pull out the batery...is there some option to turn off the magldr, without using the volume buttons? please help me..in the store workers tell me that they cant fix the broken volume buttons...and now i cant use my phone... cheers...
I have a problem with DFT MAGLDR Bootloader 1.13 version. I have HSPL 2.08 version and radio 2.15.50.14 version. I connect my HD2 and synchronize it with my computer but when I run ROMUpdateUtility the device is restarting and the progress bar is on 0% all the time. After about 30 minute the ERROR 262 appears on the screen. But the connection 'HD2->My Computer' is correct. Do you have any idea what the problem is ? Please help me.....
miod3k
Also are you right clicking the RUU and selecting run as adminastrator?
Also are you right clicking the RUU and selecting run as adminastrator?
Click to expand...
Click to collapse
Yes I do this, but it's no take effect.
HELP!!!!!
miod3k said:
Yes I do this, but it's no take effect.
HELP!!!!!
Click to expand...
Click to collapse
Hey, try re-downloading MAGLDR and connecting via another usb port or preferably another system with htc drivers installed...Hope u r flashing thru d bootloader mode and does it show "usb" instead of "serial"?
If you are still having trouble click on the link in my signature that says guide and it tells you step by step how to flash MAGLDR by flashing via bootloader. Also like the post above said try all the USB ports if you have trouble with one.
Hey, try re-downloading MAGLDR and connecting via another usb port
Click to expand...
Click to collapse
I do this but it's no take effect.
Hope u r flashing thru d bootloader mode and does it show "usb" instead of "serial"?
Click to expand...
Click to collapse
It's USB
You can also flash MAGLDR via SD card just like you can a Windows Mobile ROM. Just copy the magldr.nbh file and change the magldr.nbh file name to leoimg.nbh then copy the leoimag.nbh file to the root of your SD card. Boot your HD2 into bootloader and press the end button to comfirm when it ask if you want to flash the image.
Click to expand...
Click to collapse
When I do this, after boot my HD2 into bootloader the screen is white, and sing 'Loading...' is on the screen all the time. I wait about 15 minutes but the screen was no changes
I have a original ROM v 3.14.118.1 maybe this is the problem ?
miod3k said:
I do this but it's no take effect.
It's USB
When I do this, after boot my HD2 into bootloader the screen is white, and sing 'Loading...' is on the screen all the time. I wait about 15 minutes but the screen was no changes
I have a original ROM v 3.14.118.1 maybe this is the problem ?
Click to expand...
Click to collapse
Here r d steps and it has worked countless times...
1. U must have performed a HSPL 2.08 (not 3.03) using HSPL3/4 software. (connect usb & restart in bootloader mode)
2. Perform Task29 by connecting usb & restarting in bootloader mode (This completely wipes your phone memory).
3. Flash MAGLDR 1.13 by powering up in bootloader, connecting usb and running "RUU.exe" as Admin.
Going CWM Way?
4. Flash CWM by launching MAGLDR (Press & hold down d end key), using volume keys, scroll down & select usb flasher...Run "Daf.exe" contained in CWM folder.
5. Copy android build to root of already full-formatted sd card.
6. Enter MAGLDR mode & scroll down to AD Recovery..Enter....CWM should load up.
7. Select "Install zip from sd card".
8. Select d desired build...Enter..Scroll down to Yes, Install.....
9. Flash Away.
10. Wait for successful confirmation then select "reboot phone" ..
ENJOY!!!
2. Perform Task29 by connecting usb & restarting in bootloader mode (This completely wipes your phone memory).
Click to expand...
Click to collapse
I try do this, but after I run task29.exe I have this image on ma screen
And the progress bar was no changes(all the time is 0%). I must remove battery and put it into my HD2 again to run operating system.
Please help!!! :-(
It works!!!! I reinstall HSPL downloaded from another source and MAGLDR was install without any problem.
Thanks all of you for help....
Greetings
miod3k
problem with installation
hi guys ...
i have a problem with the installation ... i did everthing step by step as you can read in this thread http://forum.xda-developers.com/showthread.php?t=893618 ... i have htc hd2 tmo 512, installed hspl 4 (3.03), radio 2.10 ... after that i wanted to install MAGLDR 1.13, but during the installation my device hung up ... without any error ... and now it won't start anymore ... can somebody help me, please? ... thx ...
schnatterinchen said:
hi guys ...
i have a problem with the installation ... i did everthing step by step as you can read in this thread http://forum.xda-developers.com/showthread.php?t=893618 ... i have htc hd2 tmo 512, installed hspl 4 (3.03), radio 2.10 ... after that i wanted to install MAGLDR 1.13, but during the installation my device hung up ... without any error ... and now it won't start anymore ... can somebody help me, please? ... thx ...
Click to expand...
Click to collapse
change the HSPL to 2.08, it will not work with 3.03
but my device doesn't start ... when I push the power button, it hangs up so I couldn't connect it to my pc ...
take the battery out for 30 minutes and then try getting into the boot loader
how can I get into the boot loader? ...
schnatterinchen said:
how can I get into the boot loader? ...
Click to expand...
Click to collapse
hold down the volume key as per instructions when you originally flashed
Remove the cable from your device
try to to open ActivSync settings
and uncheck accept usb connection or something like that ...
reconnect your device again the try flash MAGDLR
i think it wil work for you
thx anyway ... but it won't work ... when I push the powerbutton, my device is vibrating like when it starts normally ... about one second later the tmo logo is fading up and then the diplay is freezing ... there is no other reaction ...
need help
i have installed MAGLDR v1.13 on my HTC HD2
Phone have rebooted after installation finished, but DFT MAGLDR Bootloader have not loaded after these (
now i see only a white screan with the green text: ''HTC'' on it
please can somebody help me?
Ps : i had the correct radio ROM
HSPL 3.03
Radio 2.15
Ok im now in a proper mess.
Ok ive been battling with trying to get Android on my HD2 i have manged no prob with the MAGLDR in the past but wanted to change to the CLK version.
I tried all the tried the tips etc and have downloaded the HD2 Android Nand Toolkit but i just couldnt get it working. Once i thought i did I get CLK wokring I installed the ZIP file but it just got stuck on the HTC splash screen. The only way i can it to actually boot is to put the stock Winmo ROM back on. So at the moment I have the stock ROM just with SPL. As soon as i run the Task29 option in the toolkit it then fails to load. Could somebody please advise me on what to do.
TommyHD2 said:
Ok im now in a proper mess.
Ok ive been battling with trying to get Android on my HD2 i have manged no prob with the MAGLDR in the past but wanted to change to the CLK version.
I tried all the tried the tips etc and have downloaded the HD2 Android Nand Toolkit but i just couldnt get it working. Once i thought i did I get CLK wokring I installed the ZIP file but it just got stuck on the HTC splash screen. The only way i can it to actually boot is to put the stock Winmo ROM back on. So at the moment I have the stock ROM just with SPL. As soon as i run the Task29 option in the toolkit it then fails to load. Could somebody please advise me on what to do.
Click to expand...
Click to collapse
You need Hardspl from Cotulla. Search through the threads you'll find it. but if you had magldr installed you should have all the the necesary elements. using the tool kit you have to hold the volume down than power on. wait for your phone to say usb. Than proceed to task 29. Than when the screen shuts off hold the volume down again before the screen comes on. Pick your partition size, Than hit the partiton button wait for it to do its thing than hold the back key and some text should come on your phone ending with something like fastboot commands suspend. Flash the recovery. than when it go off again hold home until you get in to recovery. Hope that helps.
Cheers for the help. Ive got as far as the revovery install i had a load of text on the screen the last line of wich is 2690 --Portchange-- and the pc is sitting on waiting for device.
also this is all it does when i turn the phone on now
TommyHD2 said:
also this is all it does when i turn the phone on now
Click to expand...
Click to collapse
Are you holding the back button until the text comes on?
Have you successful installed hspl? Successfully installed magldr and successfully installed cwm?
Is the Rom your installing a magldr version? Did you get it from the Android nand thread?
Is your SD card working is it formatted to fat32?
Are you installing the Rom from SD?
Is it a .zip file?
Edit/ oh clk..... lol never used it
Sent from my HTC HD2 using XDA Premium App
If i hold the power with the back button or the power/hangup button the text goes up to --portchange-- line if i hold the home button it shoes the line
GET STALL_DESCRIPTOR 128 6 1536 0 10
Pc is still saying waiting for device.
I have magldr but cant seem to boot to it and i have SPL-2.08.HSPL CotullaHSPL
I also tried to install magldr again and it gives a USB init failed Info \\rspl\rspl..cpp (736) but the phone is showing USB with the red\green\blue\white screen.
whynot66 said:
Have you successful installed hspl? Successfully installed magldr and successfully installed cwm?
Is the Rom your installing a magldr version? Did you get it from the Android nand thread?
Is your SD card working is it formatted to fat32?
Are you installing the Rom from SD?
Is it a .zip file?
Edit/ oh clk..... lol never used it
Sent from my HTC HD2 using XDA Premium App
Click to expand...
Click to collapse
haha..
TommyHD2 said:
Ok im now in a proper mess.
Ok ive been battling with trying to get Android on my HD2 i have manged no prob with the MAGLDR in the past but wanted to change to the CLK version.
I tried all the tried the tips etc and have downloaded the HD2 Android Nand Toolkit but i just couldnt get it working. Once i thought i did I get CLK wokring I installed the ZIP file but it just got stuck on the HTC splash screen. The only way i can it to actually boot is to put the stock Winmo ROM back on. So at the moment I have the stock ROM just with SPL. As soon as i run the Task29 option in the toolkit it then fails to load. Could somebody please advise me on what to do.
Click to expand...
Click to collapse
alls ye really need mate if you have flashed spl 2.08 or above is get task29 plug phone via USB turn phone off turn back on while holding vol down key untill tri colours appear then it says USB at bottem, run task29 from computer phone will do the rest, get magldr go back to tri colour with USB at bottem run ROMUpdateUtility install it then try the rom in my signature first typhoon and download the recovery of his page and install that specific one then flash your rom, its got installation on typhoon thread....
Cheers for the help. Ive re-installed MAGLDR and have ClockworkMOD recovery v3.0.0.5 working and I have a rom that i have downloaded and am currently downloading one of yours Laney, before i do anything clockwork MOD is showing "Failed to find Cache partition to mount at \cache.
Dont you have an sd card inserted?
Hi,
I want to instal WP7 on my HTC HD2.
In the tutorial i use i should use the Rom update utility to get MAGLDR on my phone.
When i try to use this utility i don't get further than 0% and after some time i get a error (error 626)
What i did is:
- I reseted my HTC HD2.
- I started the Rom update utility. It says that i need a update from 1.66.404.1 to 2.00.000.0.
- So when i start this it will restart my phone and show me a progres bar.
This will stay on 0% and after 10 minutes the utility gives me a message that says:
You connection is lost(error 626). Than i need to "recover" my phone by taking the battery out and put in in again.
When i do this it wel restart my phone with the WM6.5 so nothing happend.
I tryed the following things:
- A different usb cable and usb port.
- redownload the Rom Update Utility from this site.
- Hard reset my phone.
Nothing happend a still geth the same error.
Does someone know how to fix this?
Or is there a defferent way to install WP7 on my HTC HD2.
Thanks,
Maarten
read tutorial from my signature
I will try that thanks.
I finished step 0.5 and 1.
But when I am at the line "When phone boot in MAGLDR use:"
I get stuck.
The MAGLDR is installed but when the phone restart i get stuck on the white HTC screen.
Any clou what i should do next?
if not boot, press and hold power button to start magldr....
I tryed it but it wont do anything else than go to the white boot sreen with the Green HTC logo.
I tryed to press the power button for a long time and while he is booting.
Butt notting more than te boot screen shows.
The only way to start the phone again is to remove the battery.
I can get in the "red-green-blue-white screen"
I already tryed to reinstall the magldr. But no luck.
And what do you meen with "in not boot"?
The only thing it does do is boot to this logo and that's it. So its always booting when i turn it on...
"if not boot to magldr"
which HSPL you have installed on device?
try install WM6.5 first then install magldr....
first time when phone boot after magldr flashed, must boot to magldr automatically
I have HSPL2.08
It doesn't start the magldr automatically.
Even if i hold the power button. It just starting with a white boot screen with HTC logo.
Don't know how to install wm6.5 again.
Please help. I would like to use my phone tomorow again.
Edit:
Maybe it's bricked...
boot to threecolor screen and flash WM6.5
Ok I flash back to WM6.5
What to do now?
Follow the instructions again i asume.
Anyway many thanks for your help!!!
yes, after flash, install magldr and continue...
Ok I flashed my phone back to WM6.5
This is working again.
After that I installed the magldr but it doesn't load anything after that.
It says the flash went correct but when the phone reboots it goes to the white htc boot logo. And thats it.
Even if i start the phone with the power button on it doesn't go to the magldr.
Did i install the right one?
I installed the MAGLDR113_DAF
After that i tryed to flash the rom to WP7.5 but is says that the phone is not connected.
Don't know what to do anymore.
you cant flash WP7 without magldr menu (setting options and enable USB flasher in magldr)...
yes this magldr is ok...
http://forum.xda-developers.com/showthread.php?t=893618
to be sure, which version of HD2 you have?
also check data in bootloader screen (threecolor)
Data in bootloader screen:
PB81100 HX-BC
SPL-2.08.HSPL 8G XE
0x05
CotullaHSPL 0x50
Version:
I know i don't have the t-mobile version.
HTC HD2 T8585
MasterMaarten said:
Ok I flashed my phone back to WM6.5
This is working again.
After that I installed the magldr but it doesn't load anything after that.
It says the flash went correct but when the phone reboots it goes to the white htc boot logo. And thats it.
Even if i start the phone with the power button on it doesn't go to the magldr.
Did i install the right one?
I installed the MAGLDR113_DAF
After that i tryed to flash the rom to WP7.5 but is says that the phone is not connected.
Don't know what to do anymore.
Click to expand...
Click to collapse
did you perform the magdlr prep steps of clearing the mbr and uselast24nand from the services option of the main menu, then select option 5 (main menu) usb flash...then flash rom?
hjhjhj said:
did you perform the magdlr prep steps of clearing the mbr and uselast24nand from the services option of the main menu, then select option 5 (main menu) usb flash...then flash rom?
Click to expand...
Click to collapse
I used the manual from dxdy:
STEP 0.5 - from same beginning, WP7 never or not installed on phone
- If needed (if Android NAND installed, or if any error during flash
process, erase NAND with Task29). Flashing WM6.5 not needed.
- if you have SIM locked phone and want unlock with code, you can this only in WM6.5
- insert formatted microSD card to FAT32 in phone
- flash radio if you want (if flash version available) or use radio upgrade during ROM flashing (put radio file
part00.bin in data.zip file before ROM flash)
STEP 1. - when HSPL and/or MAGLDR not installed
- Flash HSPL 2.08 if needed (put device in bootloader before Flash:
press and hold Volume down + Power button)
- Flash MAGLDR 1.13 (put device in bootloader before Flash:
press and hold Volume down + Power button)
Click to expand...
Click to collapse
- I didn't erease the NAND with Task29 because i don't have android installed.
But after the last step it wont go in to the MAGLDR.
- I didn't Flash the Radio. Is this needed?
Where can i find the radio version that is installed? Or does it need to be a tweakt version from this forum?
MasterMaarten said:
I used the manual from dxdy:
- I didn't erease the NAND with Task29 because i don't have android installed.
But after the last step it wont go in to the MAGLDR.
- I didn't Flash the Radio. Is this needed?
Where can i find the radio version that is installed? Or does it need to be a tweakt version from this forum?
Click to expand...
Click to collapse
you should do task29 whether you have android or not....between flashes even if wp7. task29 cleans out the memory area where the OS will reside.
as for the radio...radio thread for the TMOUS radio is here:
http://forum.xda-developers.com/showthread.php?t=1111613
more than likely you shouldn't have to flash a radio, but it won't hurt. only have to do it once.
in order to use the rom flash utility...you have to go into magdlr main screen...scroll down to and select 10. Services, then select 5. CleanMBR, and then 4. Uselast24NAND. Finally, back at the main set of options select 5. USB Flash.
Then you kick off your DWI.exe in admin mode.