Related
hi,
MAGLDR doesn't recognize my sd card . i can't use usb mass storage , AD SD => CWM . apparently all the roms i want are released az ZIPs ...
is there a fix for that ?
Are you using magldr 1.13? If so you need to use the new CWM 1.3 partitions which now installs the partition onto NAND, so to use CWM you need to boot into the AD Recovery option from menu and not Boot AD SD. There is also no need to copy files to root of sd card.
There is a problem with magldr usb mass storage, but if you boot to CWM, select mount and storage and the usb storage you can copy perfectly.
hi
my problem is with the bootloader screen. After installing magldr 1.13 i could not start the ppc in bootloader mode. i have tried many key combinations and etc.. but it is still starting with magldr after a short white htc screen. So now i cannot load any official or custom winmo firmware. None of the android nand fw are working. Now i only can use winphone 7 with limited abilities.. Can anyone tell me the way to solve this and go back to original rom?
thanks
exxx80 said:
hi
my problem is with the bootloader screen. After installing magldr 1.13 i could not start the ppc in bootloader mode. i have tried many key combinations and etc.. but it is still starting with magldr after a short white htc screen. So now i cannot load any official or custom winmo firmware. None of the android nand fw are working. Now i only can use winphone 7 with limited abilities.. Can anyone tell me the way to solve this and go back to original rom?
thanks
Click to expand...
Click to collapse
When you say you can not start in bootloader, bootloader is started by turning the phone off, holding in the vol down button only and turning on the phone.
The phone should not even get to the white htc screen.
If you get into the tri-colour screen you can get back to a stock rom to start again.
waspsl said:
When you say you can not start in bootloader, bootloader is started by turning the phone off, holding in the vol down button only and turning on the phone.
The phone should not even get to the white htc screen.
If you get into the tri-colour screen you can get back to a stock rom to start again.
Click to expand...
Click to collapse
Yes exactly thats what i m doing. But it passes to magldr. I even have reset from the red button at the back but no way to bootloader
@ClydeB1 : so i have to install the new CWM using the USB Flasher and it'll boot from AD Recovery ? thats good news i guess ...
will it let me install ZIP roms ? also i have a 512Leo . why would i (or anyone) want to partition NAND ?!?
MTN_HD2 said:
@ClydeB1 : so i have to install the new CWM using the USB Flasher and it'll boot from AD Recovery ? thats good news i guess ...
will it let me install ZIP roms ? also i have a 512Leo . why would i (or anyone) want to partition NAND ?!?
Click to expand...
Click to collapse
Yes, install the appropriate cwm partition by going to usb flasher and running daf.exe. Then the phone will reboot to magldr, select AD recovery and you can then flash zip roms or updates, backup etc etc etc.... I have a 512 device also, so no problems.
I guess one of the reasons for running recovery off NAND is that not all users could get the sd based recovery to work.
exxx80 said:
hi
my problem is with the bootloader screen. After installing magldr 1.13 i could not start the ppc in bootloader mode. i have tried many key combinations and etc.. but it is still starting with magldr after a short white htc screen. So now i cannot load any official or custom winmo firmware. None of the android nand fw are working. Now i only can use winphone 7 with limited abilities.. Can anyone tell me the way to solve this and go back to original rom?
thanks
Click to expand...
Click to collapse
I have the same problem here. I tried to return from my NAND Android Builts to a Windows 6.5 ROM. But after Flashing, the reboot got stuck at the logo. I tried flashing over and over again, different WinRoms, reflashed MAGLDR and even tried a combination with HSPL. nothing seems to work. I dont pass the logo, cannot enter MAGLDR or load a normal build. I kinda run out of all my magic. anyone got any suggestions?
fastscorpion2010 said:
I have the same problem here. I tried to return from my NAND Android Builts to a Windows 6.5 ROM. But after Flashing, the reboot got stuck at the logo. I tried flashing over and over again, different WinRoms, reflashed MAGLDR and even tried a combination with HSPL. nothing seems to work. I dont pass the logo, cannot enter MAGLDR or load a normal build. I kinda run out of all my magic. anyone got any suggestions?
Click to expand...
Click to collapse
What hspl version and radio are you using? To use magldr you need 2.08.hspl and radio 2.08.50.xx or higher .50 radio
I'm not sure why it would hang on reflash to winmo, but let's try get to Android.
Hi!
I am using the SPL 2.08 and When i am installing the MAGLDR111 or MAGLDR113 it's Stop in 0%
How i can install the MAGLDR?
grisantycosme said:
Hi!
I am using the SPL 2.08 and When i am installing the MAGLDR111 or MAGLDR113 it's Stop in 0%
How i can install the MAGLDR?
Click to expand...
Click to collapse
you're using Stock SPL, you need Hard SPL (HSPL)
ClydeB1 said:
Are you using magldr 1.13? If so you need to use the new CWM 1.3 partitions which now installs the partition onto NAND, so to use CWM you need to boot into the AD Recovery option from menu and not Boot AD SD. There is also no need to copy files to root of sd card.
There is a problem with magldr usb mass storage, but if you boot to CWM, select mount and storage and the usb storage you can copy perfectly.
Click to expand...
Click to collapse
You...so...rock!
I've been getting utterly frustrated with watching Windows bars filling only halfway, but your solution worked like a charm!
:good: x many!
magldr problem
hi
i was instaling the magldr on my htc hd2, but during the instalation i realise that my VOLUME UP and DOWN buttons are broken and dont work...i have to choose some option in MAGLDR but i cant...so i'm stuck here, my phone boots only MAGLDR even when i restart the phone from the red button, or even when i pull out the batery...is there some option to turn off the magldr, without using the volume buttons? please help me..in the store workers tell me that they cant fix the broken volume buttons...and now i cant use my phone... cheers...
I am trying to re-flash WIN6.5 with no luck
1. I installed HSPL2.8 and MAGDLR 1.13 with the hope of trying CWM and loading Android to NAND.
2. I used ClockworkMod Recovery to install zip from SDCard using TyphooN_CM7_v2.8.0-cLK.zip
3. Progress looked like install was completed
4. When re-booting, got message NAND Kernel open failed
I TRIED TO REFLASH MY WIN6.5 from the RED/GREEN/BLUE bootloader menu but now I do not get a valid connection via USB
The Bootloader screen shows 'USB' at the bottom and when I click the Custom_RUU.exe I used to load my Custom Win6.5 ROM I get the first screen showing the update button etc. but when I press update, the progress bar appears on the PC and my HD2 but no update actually occurs
FINALLY AFTER A FEW MINUTES I GET A 'RECOVERY SCREEN' and update failed message.
CAN SOMEONE PLEASE HELP???? I will gladly 'Donate' some beer money
when you turn on your phone hold the red power button until the magldr screen pops up then go to flash to usb then download the stock rom for win 6.5 it should be in the win6.5 development threads on XDA the rom should be a .exe file, run the file once u establish a usb connection with the computer. if you can't get on the magldr screen, try going to the boot screen ( the one with the color stripes) and re-flash your magldr or the hspl4. as long as you can get into the magldr boot screen then you should be able to flash android or winmo. hope that helps.
Phongsta said:
when you turn on your phone hold the red power button until the magldr screen pops up then go to flash to usb then download the stock rom for win 6.5 it should be in the win6.5 development threads on XDA the rom should be a .exe file, run the file once u establish a usb connection with the computer. if you can't get on the magldr screen, try going to the boot screen ( the one with the color stripes) and re-flash your magldr or the hspl4. as long as you can get into the magldr boot screen then you should be able to flash android or winmo. hope that helps.
Click to expand...
Click to collapse
This couldn't be more wrong lol. You can't flash WinMo ROM's from MAGLDR, only WP7 and Android.
Anyway why don't you just try flash a different Android ROM? Even one that has a daf and not a .zip that you have through CWM.
If you do want to go back to stock though, download your stock ROM from the HTC site or T-mobile depending on which phone you have (T-mobile say t-mobile at the top and has red and green call/end buttons). Then once you've downloaded it, rename the file to .zip (should be .exe by default) then using WinRar open the file and look for a file that ends with '.nbh' in WinRar. Once you've found that file just extract it to wherever you want and rename it to 'LEOIMG.nbh'. Once you've done that, place it on the root of your SD card, then POP your SD card back in to your HD2, boot to HSPL (tri colour) and you'll come to a screen which will allow you to flash the ROM from SD and you're done.
PS. you need a 4GB or smaller SD card to flash it.
Good luck.
Sent from my HTC Vision using XDA App
Skellyyy said:
This couldn't be more wrong lol. You can't flash WinMo ROM's from MAGLDR, only WP7 and Android.
Anyway why don't you just try flash a different Android ROM? Even one that has a daf and not a .zip that you have through CWM.
If you do want to go back to stock though, download your stock ROM from the HTC site or T-mobile depending on which phone you have (T-mobile say t-mobile at the top and has red and green call/end buttons). Then once you've downloaded it, rename the file to .zip (should be .exe by default) then using WinRar open the file and look for a file that ends with '.nbh' in WinRar. Once you've found that file just extract it to wherever you want and rename it to 'LEOIMG.nbh'. Once you've done that, place it on the root of your SD card, then POP your SD card back in to your HD2, boot to HSPL (tri colour) and you'll come to a screen which will allow you to flash the ROM from SD and you're done.
PS. you need a 4GB or smaller SD card to flash it.
Good luck.
Sent from my HTC Vision using XDA App
Click to expand...
Click to collapse
I think this should work for you ,,, it always work for me this way
mburian said:
I am trying to re-flash WIN6.5 with no luck
1. I installed HSPL2.8 and MAGDLR 1.13 with the hope of trying CWM and loading Android to NAND.
2. I used ClockworkMod Recovery to install zip from SDCard using TyphooN_CM7_v2.8.0-cLK.zip
3. Progress looked like install was completed
4. When re-booting, got message NAND Kernel open failed
I TRIED TO REFLASH MY WIN6.5 from the RED/GREEN/BLUE bootloader menu but now I do not get a valid connection via USB
The Bootloader screen shows 'USB' at the bottom and when I click the Custom_RUU.exe I used to load my Custom Win6.5 ROM I get the first screen showing the update button etc. but when I press update, the progress bar appears on the PC and my HD2 but no update actually occurs
FINALLY AFTER A FEW MINUTES I GET A 'RECOVERY SCREEN' and update failed message.
CAN SOMEONE PLEASE HELP???? I will gladly 'Donate' some beer money
Click to expand...
Click to collapse
WOW!! for a newbie, u sure know how to go for d big guns ...Anyway according to your post, i tk it u downloaded the "TyphooN_CM7_v2.8.0-cLK.zip" file ryt?...Well in [cLK/MAGLDR]TyphooN CyanogenMod 7 RC2+ v2.8.4's thread, it tells you there are two ways to install this particular build...I'm guessing u tried installing the "TyphooN_CM7_v2.8.0-cLK.zip" thru MAGLDR-CWM instead of following Charmacas's cLk tutorial.
So in d spirit of learning, Start d whole process again (Task 29, etc), go back to the build's thread (link above), choose which method is most comfortable 2 u ( i recommend MAGLDR) and re-download the latest & APPROPRIATE build for the process or just download from the links below....
MAGLDR Method.
cLK Method.
Nw abt reflashing WinMO, U've got HSPL installed so u r good...Just perform a Task 29 (dis wipes ur phone clean, leaving ur HSPL & radio intact) from the bootloader screen...Should usb fail? unplug n try another usb port on your pc...Then simply flash ur desired WinMo ROM.
This my friend is what happens when dev's instructions are not followed...Do read, understand n be more careful nxt time...Donate to the devs if i helped u.
All done !
voncrane said:
WOW!! for a newbie, u sure know how to go for d big guns ...Anyway according to your post, i tk it u downloaded the "TyphooN_CM7_v2.8.0-cLK.zip" file ryt?...Well in [cLK/MAGLDR]TyphooN CyanogenMod 7 RC2+ v2.8.4's thread, it tells you there are two ways to install this particular build...I'm guessing u tried installing the "TyphooN_CM7_v2.8.0-cLK.zip" thru MAGLDR-CWM instead of following Charmacas's cLk tutorial.
So in d spirit of learning, Start d whole process again (Task 29, etc), go back to the build's thread (link above), choose which method is most comfortable 2 u ( i recommend MAGLDR) and re-download the latest & APPROPRIATE build for the process or just download from the links below....
MAGLDR Method.
cLK Method.
Nw abt reflashing WinMO, U've got HSPL installed so u r good...Just perform a Task 29 (dis wipes ur phone clean, leaving ur HSPL & radio intact) from the bootloader screen...Should usb fail? unplug n try another usb port on your pc...Then simply flash ur desired WinMo ROM.
This my friend is what happens when dev's instructions are not followed...Do read, understand n be more careful nxt time...Donate to the devs if i helped u.
Click to expand...
Click to collapse
Thanks m8... I figured out my problem... HAVE TO RUN EVERYTHING 'AS ADMINISTRATOR' ... anyway... won't make that mistake again...
Thanks Everyone for all your help!!!!
mburian said:
Thanks m8... I figured out my problem... HAVE TO RUN EVERYTHING 'AS ADMINISTRATOR' ... anyway... won't make that mistake again...
Thanks Everyone for all your help!!!!
Click to expand...
Click to collapse
Glad 2 help, just hit d thanks button nxt time....Enjoy ur device.
mburian said:
I am trying to re-flash WIN6.5 with no luck
1. I installed HSPL2.8 and MAGDLR 1.13 with the hope of trying CWM and loading Android to NAND.
2. I used ClockworkMod Recovery to install zip from SDCard using TyphooN_CM7_v2.8.0-cLK.zip
3. Progress looked like install was completed
4. When re-booting, got message NAND Kernel open failed
I TRIED TO REFLASH MY WIN6.5 from the RED/GREEN/BLUE bootloader menu but now I do not get a valid connection via USB
The Bootloader screen shows 'USB' at the bottom and when I click the Custom_RUU.exe I used to load my Custom Win6.5 ROM I get the first screen showing the update button etc. but when I press update, the progress bar appears on the PC and my HD2 but no update actually occurs
FINALLY AFTER A FEW MINUTES I GET A 'RECOVERY SCREEN' and update failed message.
CAN SOMEONE PLEASE HELP???? I will gladly 'Donate' some beer money
Click to expand...
Click to collapse
you must istall zip for MAGLDR not for CLK!!
mburian said:
I am trying to re-flash WIN6.5 with no luck
1. I installed HSPL2.8 and MAGDLR 1.13 with the hope of trying CWM and loading Android to NAND.
2. I used ClockworkMod Recovery to install zip from SDCard using TyphooN_CM7_v2.8.0-cLK.zip
3. Progress looked like install was completed
4. When re-booting, got message NAND Kernel open failed
I TRIED TO REFLASH MY WIN6.5 from the RED/GREEN/BLUE bootloader menu but now I do not get a valid connection via USB
The Bootloader screen shows 'USB' at the bottom and when I click the Custom_RUU.exe I used to load my Custom Win6.5 ROM I get the first screen showing the update button etc. but when I press update, the progress bar appears on the PC and my HD2 but no update actually occurs
FINALLY AFTER A FEW MINUTES I GET A 'RECOVERY SCREEN' and update failed message.
CAN SOMEONE PLEASE HELP???? I will gladly 'Donate' some beer money
Click to expand...
Click to collapse
you must istall romzip for MAGLDR not for CLK!!
Hey guys, I've managed to install MAGLDR on my HD2, and I have tried to install CWM.
First I tried v1.3 and everything went OK till i got stuck on the "Go Go Go" screen.
Then I tried v1.2 using my SD card, but i still end up with the same problem.
The thing is I don't have any ROM installed on my HD2 so I can't do anything more !
Would greatly appreciate your help =)
do you use MAGLDR 1.13?
did you try and reinstall your ROM?
Do you use a compatible radio?
Yep I'm on 1.13
I can't do much more, my HD2 won't even boot into the bootloader ! I'm basically stuck on MAGLDR with no ROM and no ability to install back a standard windows ROM
Eelkede said:
Do you use a compatible radio?
Click to expand...
Click to collapse
I followed the steps carefully, so it should be OK but how can I be sure ?
Make sure your battery pins aren't loose. Push them back with your finger and try again.
Sent from my HTC Vision using XDA App
Tried about everything I could hardware-wise without tearing it apart... unfortunately the battery pins don't change anything.
Quite a few members seem to be facing the same problem recently: no access to the bootloader, stuck on MALDR... wonder what's the problem.
The only thing I can do is run WP7 on it, which is not very usable.
i made this: http://forum.xda-developers.com/showthread.php?t=945427
maybe it helps?
Thanks yz.hd but I can't get to the bootloader (volume down + power only brings me to MAGLDR), nor CWM...
It's not possible to only be able to get to MAGLDR and not bootloader I don't think. Just hold down the volume button and then power on while still holding down the power button and see what happens. I had a problem like that where my HD2 would get stuck at "1234" and then stopped and rebooted. The battery pins where the cause.
Sent from my HTC Vision using XDA App
I've tried loads of times, the combo volume down + power really doesn't bring anything up, no matter which way I put it... a complete mystery !
So you've tried to install CWM? Did it work or not? Are you able to go to the USB flasher in Magldr? And install it again, try to see if the AD Recovery works?
Yep, I tried again, the USB flasher works perfectly fine, CWM installs perfectly. But when I go to Ad recovery, it still stays on "Go Go Go!".
Same thing if i install CWM via my SD card
Try formatting SD card (you will lose your data). Try again.
How long does it hang?
If that doesn't work, try to install a DAF rom, and see what happens.
you probably don't have the 'copy to sd' folder in the root of your sd?
Sent from my HTC HD2 using XDA Premium App
Eelkede said:
Try formatting SD card (you will lose your data). Try again.
How long does it hang?
If that doesn't work, try to install a DAF rom, and see what happens.
Click to expand...
Click to collapse
What do you mean by a DAF Rom ? One that is directly bootable from MAGLDR ? I have tried a WP7 rom which works ok. But I still can't install a bootloader to bring it back to WP 6.5 and start the process all over again to install CWM...
@DKxda: is it necessary to have a folder ? I copied the two files directly in the root of my SD.
DAF rom is a rom that doesn't use CWM to run (directly from magldr).
Nope I'm still stuck on Go Go Go if I want to install a DAF Android ROM (no problem with WP7 ROMs though)...
Sorry mate, I'm out of options you could try (well, install CLK, but you need the bootloader for that...)
Hope someone else will help you fix this!
Edit: When does it get stuck at go go go? Immediately at boot or after selecting Boot AD Nand?
You can try to ask it in the Magldr Thread, cause it seems like a Magldr problem to me...
Eelkede said:
Sorry mate, I'm out of options you could try (well, install CLK, but you need the bootloader for that...)
Hope someone else will help you fix this!
Edit: When does it get stuck at go go go? Immediately at boot or after selecting Boot AD Nand?
You can try to ask it in the Magldr Thread, cause it seems like a Magldr problem to me...
Click to expand...
Click to collapse
Well, since yesterday I'm getting a similar issue!
Stuck at go go go or just after on the boot screen which is completely messed I get the top 1/4 screen ok, the rest is bad lines, then the bottom half is dark.
Yesterday I tried installing a CM7 build for my HD2... stuck at Android logo...
So I reflashed CWM Recovery 400Mb partition ok, restored my last backup and rebooted... Now I have this issue all the time!
Tried my many backups, reflashing CWM Recovery a couple of times, factory reset from CWM or MAGLDR...
Nothing will do!
Is my HD2 dead or what????
HI there so i bought a used HD2 wich came with ICS installed when it arrived i turned it on and loaded MAGLDR then it tried to load Android but got stuck at the GO GO GO! line. As i dont have any drivers installed and Windows doesnt recognize the HD2 in MAGLDR i cant flash a new rom. I wanted to do a Task 29 but that requires drivers too.
So my question is how do i perform a full wipe so i can get a working rom since the phone turns on, shows the TMobile splash screen then goes into Magldr and tries to boot android immediately then get sutck in GO GO GO!.
hold power button until magldr menu appear
in ad recovery you can wipe anything
Pentuni said:
HI there so i bought a used HD2 wich came with ICS installed when it arrived i turned it on and loaded MAGLDR then it tried to load Android but got stuck at the GO GO GO! line. As i dont have any drivers installed and Windows doesnt recognize the HD2 in MAGLDR i cant flash a new rom. I wanted to do a Task 29 but that requires drivers too.
So my question is how do i perform a full wipe so i can get a working rom since the phone turns on, shows the TMobile splash screen then goes into Magldr and tries to boot android immediately then get sutck in GO GO GO!.
Click to expand...
Click to collapse
good to know u want to start from scratch...u ll never know wats been put it that device... ....here is wat you can do
i had put out these steps in another thread to help out a fellow XDAian... try
files you need: (if you need pm me)
-task29
-Radio Leo 2.15.50.14
-DFT_LEO_MAGLDR113_DAF
-Recovery_150M_system_5M_cache
-rom zip (dont alter/extract zip if you done know wat to do with this)
do these: (from your current WP7 rom)
-restart device
-get into tricolor bootloader
-plug usb...hd2 should say 'USB'
-do a task 29
-get into bootloader again
-plug usb...hd2 should say 'USB'
-install radio by running 'CustomRUU.exe'
-get into tricolor bootloader
-plug usb...hd2 should say 'USB'
-run DAF.exe for installing MAGLDR
-reboot
-get into MAGLDR by holing power/end key while booting
-go to 'usb flasher' in the menu and press green/call button
-plug usb...hd2 should say 'USB'
-wait till it say 'wait usb...usb'
-get into your recovery folder
-run daf.exe
-reboot post completion
-get into MAGLDR by holing power/end key while booting
-get into ad-recovery
-get into mount storage
-activate usb mass storage
-now put the rom zip files into sd card
-press power to get back to recovery menu
-select install rom from sdcard
-choose rom file
-select install
this should typically install nandroid into your hd2...
if you face any issues, share the step and the error scenario/msg
I tried to get task29 but my PC doesn't recognize the hd2 even on bootloader.
Sent from my MB860 using xda premium
Edit: So i managed to get the drivers and got the phone recognized, so i performed task 29, worked perfectly. Followed the steps but when i try to install a radio it fails and gets stuck at 96%. I tried flashing the radio several times but no luck... What am i doing wrong?
It's better if you download the drivers because it's useful for later needs...
Best regards
Sam Razzy...
Sent from my HD2 using xda premium
Pentuni said:
Edit: So i managed to get the drivers and got the phone recognized, so i performed task 29, worked perfectly. Followed the steps but when i try to install a radio it fails and gets stuck at 96%. I tried flashing the radio several times but no luck... What am i doing wrong?
Click to expand...
Click to collapse
can u provide more details....actually as much details on the hd2 (eu/us), hspl, radio version, your process on how u tried etc...we will help you solve this.
gdsbalaji said:
can u provide more details....actually as much details on the hd2 (eu/us), hspl, radio version, your process on how u tried etc...we will help you solve this.
Click to expand...
Click to collapse
Their is a guide in my signature, its got basically everything you need to know. If you have problems post on there or pm me. I will gladly help.
Sent from my HD2 using xda premium
gdsbalaji said:
can u provide more details....actually as much details on the hd2 (eu/us), hspl, radio version, your process on how u tried etc...we will help you solve this.
Click to expand...
Click to collapse
I have the T Mobile US version, HSPL SPL-2.08.HSPL 8G XE COtullaHSPL 0x05 0x50(what it says on tricolor bootloader). The radio i tried to install is 2.15.50.14.
I got the drivers, my PC finally got a connection with the HD2 so i performed a task29 and wiped the phone then i followed your guide tried to install the radio but the process with CustomRUU.exe got stuck at 96% and said there was an error "this update utility can not be used on your device." and now the phone shows an Update Fail screen without a radio i cant install MAGLDr then install WP7 on it so what can i do?
kylew1212 said:
Their is a guide in my signature, its got basically everything you need to know. If you have problems post on there or pm me. I will gladly help.
Sent from my HD2 using xda premium
Click to expand...
Click to collapse
Thank you i read your guide. So can i instal clK without a radio? Also can i install ICS beta10 or Windows Phone 7 with cLK and witout going through the radio installation?
Another thing... the came with almost no battery and i cant charge the phone with the update failed screen i saw that i need at least 50% of battery but i dont think the phone has that much.
Pentuni said:
Thank you i read your guide. So can i instal clK without a radio? Also can i install ICS beta10 or Windows Phone 7 with cLK and witout going through the radio installation?
Another thing... the came with almost no battery and i cant charge the phone with the update failed screen i saw that i need at least 50% of battery but i dont think the phone has that much.
Click to expand...
Click to collapse
Okay sorry I should've explained more..
yes you have to have a radio.
Yes you can install ics beta 10 with clk.
No you cannot install wp7 with clk magldr is required for that.
If your phone is getting close to running out of battery I would flash clk 1.5 via SD card and then charge the phone up
Sent from my HD2 using xda premium
Ok so i got the radio installled and proceeded with the process with magldr installed fine and i followed this guide to get WP7.
http://forum.xda-developers.com/showthread.php?t=1246040
After the installation the phone syas reboot now! but doesnt do anything i had to pull out the battery and now it wont boot. ts stuck in a blank magldr menu.
EDIT: I managed to get magldr to show something, it tries to boot WPH but says 1eFATAL HIT 1. Did i scre up the installation? If i hold the power button it keeps doing the same thing without showing the options menu how do i wipe the rom so i can flash a new one?
Edit 2: flashed wp7 again boots magldr then sticks on GO GO GO! again.
I'm having the same problem until today.
Did a task29, installed magldr, cwm, then a rom, radio is 2.15.50.14.
It can boot to CWM, it can reinstall the rom but it's gets stuck in the go go go after restarting.
Please help
TIA
I know how to use magldr, but not tons about it.. also I think you guys should post in the wp forums someone there may be better help
Sent from my HD2 using xda premium
Pentuni said:
Ok so i got the radio installled and proceeded with the process with magldr installed fine and i followed this guide to get WP7.
http://forum.xda-developers.com/showthread.php?t=1246040
After the installation the phone syas reboot now! but doesnt do anything i had to pull out the battery and now it wont boot. ts stuck in a blank magldr menu.
EDIT: I managed to get magldr to show something, it tries to boot WPH but says 1eFATAL HIT 1. Did i scre up the installation? If i hold the power button it keeps doing the same thing without showing the options menu how do i wipe the rom so i can flash a new one?
Edit 2: flashed wp7 again boots magldr then sticks on GO GO GO! again.
Click to expand...
Click to collapse
Its happened to me before. Make sure as soon as you flash magldr, thats you clear mbr on sd card and use last 24 nand, and you will be fine, otherwise you will stay stuck on go go go go
good luck!
Yep.. thats a problem for you, but also for me, i have HTC HD2 fully working, just replaced digitzier soon, WinMo just works flawless thought it sucks ballls, and whenever i try to do task 29 then install radio then install magldr then install cwm with the required partition, i get stuck on GO GO GO! ..
Hello
I just flashed CLK on my hd2 using the toolkit, I also flashed the toolkit recovery (which i believe was v 4.3)
Now when I try to boot to recovery using Home + red buttons I get this error in the middle of the command lines
"ERROR: CANNOT READ RECOVERY_HEADER"
I tried to wipe all and reflash everything again but I keep getting the same error.
I looked everywhere but can't find any answer.
Is there any other way I can install a new ROM without accessing the CWM? like using the command prompt.
I also attached a screenshot of the error.
Any help would be very much appreciate it. and Please if there is a solution please show the steps for it cuz I am still new with CLK.
The latest stable version of clk is v1.5 which also installs a version of cwm , there is even one that installs twrp recovery too!
No links on my phone but will be easy to find...
BTW did you select clk install recovery option after clk reparation?
Sent from my NexusHD2 using xda premium
shanman-2 said:
The latest stable version of clk is v1.5 which also installs a version of cwm , there is even one that installs twrp recovery too!
No links on my phone but will be easy to find...
BTW did you select clk install recovery option after clk reparation?
Sent from my NexusHD2 using xda premium
Click to expand...
Click to collapse
I installed clk v1.5.1.1 just now but the phone freezed on "stick together" screen. any other way?
What does it say on the boot loader screen?
how did you Install? All steps you took?
Sent from my NexusHD2 using xda premium
shanman-2 said:
What does it say on the boot loader screen?
how did you Install? All steps you took?
Sent from my NexusHD2 using xda premium
Click to expand...
Click to collapse
I downloaded this file provided in clk thread "black_lk_20120920-TouchRec_b8" I installed it using the toolkit, I then added the LEOIMG file to the toolkit and flashed it.
And I can't get to the boot loader screen, I get the "stick together" screen once I turn on the phone, and then it freezes.
mjody said:
I downloaded this file provided in clk thread "black_lk_20120920-TouchRec_b8" I installed it using the toolkit, I then added the LEOIMG file to the toolkit and flashed it.
And I can't get to the boot loader screen, I get the "stick together" screen once I turn on the phone, and then it freezes.
Click to expand...
Click to collapse
Hold the volume down button and power on the device is not working ?????
Edit: what LEOIMG file???
shanman-2 said:
Hold the volume down button and power on the device is not working ?????
Edit: what LEOIMG file???
Click to expand...
Click to collapse
UPDATE! Ok I think I didn't install the right file earlier but I just downloaded the clk from here:
http://forum.xda-developers.com/showpost.php?p=21608340&postcount=848
it boots fine to the clk first screen. which I will add a picture of.
but It gives me this message when I select recovery. (Also a picture added)
ps: thank you very much for keeping up with me so fast.
mjody said:
UPDATE! Ok I think I didn't install the right file earlier but I just downloaded the clk from here:
http://forum.xda-developers.com/showpost.php?p=21608340&postcount=848
it boots fine to the clk first screen. which I will add a picture of.
but It gives me this message when I select recovery. (Also a picture added)
ps: thank you very much for keeping up with me so fast.
Click to expand...
Click to collapse
What version of hspl do you have installed?
If it's hspl 2.08 or hspl 3.03 try this,
first do a task29 using the toolkit
Then place the LEOIMG.nbh file on the root of your sdcard.
Now power on the device while holding the volume down button.
When asked to proceed with install push the power button..
This should install clk 1.5 with a default partition size which you can change from within clk later!
Let me know if it works.
shanman-2 said:
What version of hspl do you have installed?
If it's hspl 2.08 or hspl 3.03 try this,
first do a task29 using the toolkit
Then place the LEOIMG.nbh file on the root of your sdcard.
Now power on the device while holding the volume down button.
When asked to proceed with install push the power button..
This should install clk 1.5 with a default partition size which you can change from within clk later!
Let me know if it works.
Click to expand...
Click to collapse
I tried flashing it that way but it doesn't work with me, when I press volume down button with power it only shows the multicolored screen.
I also tried to restore the stock rom, by installing the rom from TMOUS website, my phone also freezes on the firs boot screen, "Stick Together"
by looking at this thread, http://forum.xda-developers.com/showthread.php?t=1063807
I think I got a hardware issue, RIP my hd2
mjody said:
I tried flashing it that way but it doesn't work with me, when I press volume down button with power it only shows the multicolored screen.
I also tried to restore the stock rom, by installing the rom from TMOUS website, my phone also freezes on the firs boot screen, "Stick Together"
by looking at this thread, http://forum.xda-developers.com/showthread.php?t=1063807
I think I got a hardware issue, RIP my hd2
Click to expand...
Click to collapse
Maybe so.
What way did you flash stock rom?
I don't understand why you cannot flash clk from the sdcard!
Have you tried a different sdcard??
What version of hspl do you have on that multicolored screen if you have anything?????
Edit:Hey, I hit the thanks by mistake but wtf, welcome to xda! :laugh:
shanman-2 said:
Maybe so.
What way did you flash stock rom?
I don't understand why you cannot flash clk from the sdcard!
Have you tried a different sdcard??
What version of hspl do you have on that multicolored screen if you have anything?????
Edit:Hey, I hit the thanks by mistake but wtf, welcome to xda! :laugh:
Click to expand...
Click to collapse
I did task29 then downloaded the rom file from t-mobile webisite then put phone on multicolored with usb debugging and ran the file on my computer.
I actually had this phone for almost 3 years now and I flashed about 4 different versions of android but i was using mgldr.
the phone was doing great with me but about 4 days I wanted to go to recovery to back up the phone I got "1E FATAL HIT 1"
I read that some one had the same issue and they switched to clk and it worked fine, and someone flashed stock rom then custom and it worked.
but nothing is working with me, I have 2.08 hspl and I've been using that for a long time, I tried 3 sdcards using both ways of flashing (toolkit and putting LEOIMG file in the sdcard) but it failed in all of them.
PS: thank you for the thank though I have been here since I got the phone and never got one thanks haha.
mjody said:
I did task29 then downloaded the rom file from t-mobile webisite then put phone on multicolored with usb debugging and ran the file on my computer.
I actually had this phone for almost 3 years now and I flashed about 4 different versions of android but i was using mgldr.
the phone was doing great with me but about 4 days I wanted to go to recovery to back up the phone I got "1E FATAL HIT 1"
I read that some one had the same issue and they switched to clk and it worked fine, and someone flashed stock rom then custom and it worked.
but nothing is working with me, I have 2.08 hspl and I've been using that for a long time, I tried 3 sdcards using both ways of flashing (toolkit and putting LEOIMG file in the sdcard) but it failed in all of them.
PS: thank you for the thank though I have been here since I got the phone and never got one thanks haha.
Click to expand...
Click to collapse
I don't understand why you cannot flash clk from the sdcard!
Click to expand...
Click to collapse
Now I do, I think!
I have asked you what it says on the multicolored screen a few times.
Pic please?
Flashing stock rom should do the trick as regards verifying that it's not a hardware problem, but it will have wiped your hspl!
So to install clk v1.5, you will have to re-flash hspl 2.08 (no zeros after the 8) or hspl 3.03!
shanman-2 said:
Now I do, I think!
I have asked you what it says on the multicolored screen a few times.
Pic please?
Flashing stock rom should do the trick as regards verifying that it's not a hardware problem, but it will have wiped your hspl!
So to install clk v1.5, you will have to re-flash hspl 2.08 (no zeros after the 8) or hspl 3.03!
Click to expand...
Click to collapse
Sorry for that, here is a picture of what you need. And this picture is while I have the stock rom installed on the phone now.
I tired to install clk 1.5 before flashing stock rom.
mjody said:
Sorry for that, here is a picture of what you need. And this picture is while I have the stock rom installed on the phone now.
I tired to install clk 1.5 before flashing stock rom.
Click to expand...
Click to collapse
OK, I would not give up yet.
Re-install hspl and this time select "3.03", then task 29 and try to reinstall clk 1.5...
Edit: If the last thing you did was install stock it won't work with hspl installed,
It should say something like..SPL-2.08.0000, use the hspl 3.03 package to downgrade to this spl version and then install stock from pc as normal (MAKE SURE you are using the correct stock rom for your phone) or as I said, try the above...
shanman-2 said:
OK, I would not give up yet.
Re-install hspl and this time select "3.03", then task 29 and try to reinstall clk 1.5...
Edit: If the last thing you did was install stock it won't work with hspl installed,
It should say something like..SPL-2.08.0000, use the hspl 3.03 package to downgrade to this spl version and then install stock from pc as normal (MAKE SURE you are using the correct stock rom for your phone) or as I said, try the above...
Click to expand...
Click to collapse
I am getting really frustrated now!
for clk:
I upgraded the hspl to 3.03, then installed clk 1.5. UNFORTUNATELY I am still getting the same message when I boot into recovery.
for stock rom: (I got it from t-mobile website which is the right one for my phone)
after failing to install clk, I FIRST downgraded the hspl to SPL 3.03.0000 and tried to flash the stock rom but the percentage bar doesn't even move. So I decided to try it with 2.08.0000 but the same thing happens. This doesn't happen when I have 3.03.HSPL or 2.08.HSPL, it actually loads when I have the hspl but then when it is done, I get stuck in "stick together" screen.
mjody said:
I am getting really frustrated now!
for clk:
I upgraded the hspl to 3.03, then installed clk 1.5. UNFORTUNATELY I am still getting the same message when I boot into recovery.
for stock rom: (I got it from t-mobile website which is the right one for my phone)
after failing to install clk, I FIRST downgraded the hspl to SPL 3.03.0000 and tried to flash the stock rom but the percentage bar doesn't even move. So I decided to try it with 2.08.0000 but the same thing happens. This doesn't happen when I have 3.03.HSPL or 2.08.HSPL, it actually loads when I have the hspl but then when it is done, I get stuck in "stick together" screen.
Click to expand...
Click to collapse
Have you tried this it's about the only option left...
I knew I had seen that thread before somewhere..
Maybe someone else has an idea, samsamuel might swing by but worth trying the above anyway...
best of luck
shanman-2 said:
Have you tried this it's about the only option left...
I knew I had seen that thread before somewhere..
Maybe someone else has an idea, samsamuel might swing by but worth trying the above anyway...
best of luck
Click to expand...
Click to collapse
It is not working! I took off the battery and back on and kept holding the restore button like 10 times.
Ugh I got a headache working on this for a week.
Thank you for your help man! and I hope someone can find out what the heck is wrong with my phone.