Hello,
I have bought a htc hd2 with a problem. Phone don't start up and is stuck in the bootloader. If i want to flash a stock ROM form sd, the phone give's a little grey flash next it turn back to bootloader. Didn't react on USB, only say serial, you don't hear a signal from windows when you put in phone.
Only thing it says in the bootloader:
PB81100 HX-BC
SPL-3.03.0000 XE
MicroP(led) 0x05
MicroP(touch) 0x40
Phone is has overheating problem, Feels a way to hot for standby in bootloader.
What is it?
- Dead USB (motherboard?)
- Bricked?
Greets,
wippie said:
Hello,
I have bought a htc hd2 with a problem. Phone don't start up and is stuck in the bootloader. If i want to flash a stock ROM form sd, the phone give's a little grey flash next it turn back to bootloader. Didn't react on USB, only say serial, you don't hear a signal from windows when you put in phone.
Only thing it says in the bootloader:
PB81100 HX-BC
SPL-3.03.0000 XE
MicroP(led) 0x05
MicroP(touch) 0x40
Phone is has overheating problem, Feels a way to hot for standby in bootloader.
What is it?
- Dead USB (motherboard?)
- Bricked?
Greets,
Click to expand...
Click to collapse
Sounds like motherboard to me.
Have you tried the freezer trick?
wippie said:
the phone give's a little grey flash next it turn back to bootloader.
Click to expand...
Click to collapse
often points to either an incompatible .nbh file or (more commonly) an sd card that is too large. Use a 2gb card for preference, most 4gb will work too, 8 and higher rarely work.
Hmmm... I use a 16gb and never had any problems.
No idea about incompatible .nbh files tho'....
Something is doing too much work or isn't able to handle it's normal workload, I'd say!
So could be software or hardware, let's try and rule out the hardware first, maybe.
shanman-2 said:
Hmmm... I use a 16gb and never had any problems.
Click to expand...
Click to collapse
you're about the third person since 2009 to say they have a 16gb card that works for flashing .nbh files, , must be just one or two very particular chips.
(BTW, i do agree it sounds like hardware, I was just pointing out the usual reason for the brief grey flash.)
Before i rip the hole phone apart i must be sure that it isn't a software problem.
When i replace motherboard, its the same thing like: buy a new phone.
the phone can stay for ours in the bootloader, feels a little hot but don't shut itself down.
Is there a way that USB not show up in the bootloader because i have the wrong drivers? USB always shows up when you put in a USB cable?
This disapoint me
http://forum.xda-developers.com/showthread.php?t=1541554
Freezer trick? Or as Samsamuel suggested smaller SD card? Results?
Sent from my NexusHD2 using xda premium
---------- Post added at 07:35 PM ---------- Previous post was at 07:29 PM ----------
Freezer trick? Or as Samsamuel suggested smaller SD card? Results?
Edit: beginning to think sdcard might be the issue..a little warm or way too hot?
Sent from my NexusHD2 using xda premium
4 Gigabyte already tried. Problem that worry me, I dont hear anny signal from pc when i put in my phone. Normally you hear a signal but nothing happens.
When it is a software error, you have to hear always the signal when you put in a cable.
i hadn't realised you weren't getting 'usb' in bootloader either, it looks more and more like hardware, then.
samsamuel said:
i hadn't realised you weren't getting 'usb' in bootloader either, it looks more and more like hardware, then.
Click to expand...
Click to collapse
SDcard is hardware is it not?
Edit: Feedback from the OP would help, don't you think?.
@OP Have you tried any of the the suggestions given?
Tried a few custom ROMS now. With all ROM's i got the grey flash and get stuck in bootloader as usual. .
Is there anything else i can try to flash via SD, so maybe after that the USB come,s back?
Hi, you can't flash roms from Sdcard because you must do hard SPL before that and the information of the bootloader should be like this:
PB81100 HX-BC
SPL-3.03.HSPL XE
0x05
CotullaHSPL 0x40
Edit: About the signal from pc I think may be the problem in the cable or PC itself (Windows).
I have tried 3 pc,s now but no one you hear a signal or see anything.
Hard SPL you can only flash via USB?
I have this bootloader screen. Only SPL is diffrent: 3.03.0000
It's looking like a bricked device. charging LED burns never. Not with USB or without USB.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
no, hspl does not mean 'usb flashing only', , it just means only NON stock roms from sd (since stock roms will remove hspl)
You don't currently have hspl installed, so only the correct network/region stock roms will flash, nothing else.
Hmm,
I have replaced motherboard now. Phone is working fine offcourse .
Dont know, maybe for later project this motherboard is usefull.
USB can never be deactivated by anny kind of brick?
So maybe is well a new one on the board.
I had this problem before but i fix it by doing Jtag on it i don't know how to do it but some store done that
After that i triple boot on hd2
Try jtag thats what i recommended
Sent from my Nexus 7 using xda premium
Related
Hey guys ! i have tried to Install the ROM and when it install the program stop and now i stuck in the bootloader i can't go into my mobile anymore how and it said not allow 00028002 plss help me guys !
Have you installed HSPL? Which spl version is showing in bootloader?Which rom are you trying to install and which method of installing are you trying?
You need to provide more info if anyone is going to be able to help you. All is not lost, the fact that you are still in bootloader means this can be recovered.
I installed HSPL and SPL-1.42.0000 and i tried to install English ROM cause i bought it from my friend and language is Russian :| and i want change it into english !
can u even get into the 3 color screen by using VolDown button?
Maxnguyen said:
I installed 2 HSPL and i tried to install English ROM cause i bought it from my friend and language is Russian :| and i want change it into english !
Click to expand...
Click to collapse
As i asked earlier, what spl version is showing in bootloader? Many people think they have installed hspl2 but they have in fact not done it properly, hence my question.
There are also many many different english roms, so of these, which one are you trying? Again please provide the details otherwise you make it almost impossible for anyone to help you without guessing.
Edit: Ok I see from your earlier reply (which you have since edited) that you have spl 1.42.0000 - that is not hspl that is a stock spl and that's probably why the rom does not install. You need to use 1.42.hspl.
hOW TO INSTALL THE hspl ???
bountygiver said:
can u even get into the 3 color screen by using voldown button?
Click to expand...
Click to collapse
yes i can ! And now i stuck in that i can't even go into my mobile !
ClydeB1 said:
As i asked earlier, what spl version is showing in bootloader? Many people think they have installed hspl2 but they have in fact not done it properly, hence my question.
There are also many many different english roms, so of these, which one are you trying? Again please provide the details otherwise you make it almost impossible for anyone to help you without guessing.
Edit: Ok I see from your earlier reply (which you have since edited) that you have spl 1.42.0000 - that is not hspl that is a stock spl and that's probably why the rom does not install. You need to use 1.42.hspl.
Click to expand...
Click to collapse
It's a English Europe ROM and now i even can't connect my phone to computer because i stuck in the Bootloader with tri colour
Here is the problem :
1/
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
[/IMG]
2/
[/IMG]
3/AND I STUCK HERE I EVEN DUN NEED TO PRESS VOLUME DOWN BUTTON !
[/IMG]
4/ I FOUND OUT SOMETHING NEW WHEN I RESTART THE PHONE I PRESS THE VOLUME DOWN BUTTON AND I GOT THIS !
[/IMG]
when phone is in three color screen
1 - connect to usb
2 - run hspl2
3 - choose your hspl
DO NOT choose one that ends .0000
DO choose one that ends.hspl
4 - when phone restarts, go into bootloader (three coloured screen) make sure that next to spl it says x.xx.hspl and NOT x.xx.0000
5 - with phone in bootloader, connect again USB
6 - flash your rom.
7 - if the rom requires a different radio, flash teh radio, just like the rom.
samsamuel said:
when phone is in three color screen
1 - connect to usb
2 - run hspl2
3 - choose your hspl
DO NOT choose one that ends .0000
DO choose one that ends.hspl
4 - when phone restarts, go into bootloader (three coloured screen) make sure that next to spl it says x.xx.hspl and NOT x.xx.0000
5 - with phone in bootloader, connect again USB
6 - flash your rom.
7 - if the rom requires a different radio, flash teh radio, just like the rom.
Click to expand...
Click to collapse
i DID LIKE WHAT YOU SAY IT'S WORK BUT WHEN IT'S INSTALL MAYBE 10% AND THE SCREEN BECAME DARK AND IT RETURN TO THE OLD SPL-1.42.0000 :| I WAS CHOOSE 2.08.HSPL AND THEN I GOT spl-2.08.HSPL 8G XE BUT WHEN THE SCREEN BECAME DARK IT'S BACK TO SPL-1.42.0000
sounds like you are flashing a stock rom from sd card, , the first thing that happes is the hspl gets overwritten by the stock 1.42.0000 and so teh rest of the flash fails.... use USB not SD
If you 'think' you already are using USB, then you have left leoimg.nbh on your sd card, , , get rid of it.
Maxnguyen said:
i DID LIKE WHAT YOU SAY IT'S WORK BUT WHEN IT'S INSTALL MAYBE 10% AND THE SCREEN BECAME DARK AND IT RETURN TO THE OLD SPL-1.42.0000 :| I WAS CHOOSE 2.08.HSPL AND THEN I GOT spl-2.08.HSPL 8G XE BUT WHEN THE SCREEN BECAME DARK IT'S BACK TO SPL-1.42.0000
Click to expand...
Click to collapse
Hi
1. When it is on Bootloader connect usb
2. Run HSPL2
3. Select 1.42 hspl
4. When HSPL successful you will see on the bootloader spl name is changed
Then
5. Download a rom and the Latest radio from this forum
6. Get bootloader and flash the radio first
7. then flash the rom
DO NOT FLASH THE STOCK ROM FROM A CARD
It will change the spl
Good luck
samsamuel said:
sounds like you are flashing a stock rom from sd card, , the first thing that happes is the hspl gets overwritten by the stock 1.42.0000 and so teh rest of the flash fails.... use USB not SD
If you 'think' you already are using USB, then you have left leoimg.nbh on your sd card, , , get rid of it.
Click to expand...
Click to collapse
u mean delete the LEOIMG.bnh in SD card and take it off so how can i flash without put it into SD card ??
You don't even need HSPL on your phone if you are flashing stock rom... Just download the official english rom and click on it when your phone is in bootloader mode and reads "USB" down bottom, then it will flash to your phone.
I don't even use HSPL when flashing custom roms... I use SSPL.
Maxnguyen said:
u mean delete the LEOIMG.bnh in SD card and take it off so how can i flash without put it into SD card ??
Click to expand...
Click to collapse
Flash over USB
Into bootloader, plug in usb cable, , when the word 'serial' becomes 'usb' on the phone, run your rom update.
Thax u ! ^^~ finnaly i did it ! thax u a lotttttttttttttttttttt
http://forum.xda-developers.com/showthread.php?t=631537
read this thread.. have your all required answers..
Hi i got a HD2 but it wont start
I tryed difrent accu from a college and his device just start and mine not
Any help ?
Greatings
Marcel
EDIT: I got the device starting up in the color bars(bootloader) But i cant flash it
HD2 wont flash
Hi my previous post that the device wont turn on i closed that one.
I am at the tree color screen but when i want to flash a radio or os then it hangs at 0% also i cant hardspl the device.
I cant use the device at this moment
applied hspl?
must be purely coincidental, and something completely different, but my HD won't start up since this mornming either...
Question: Do you get an orange led while charging? If so, my connector is probably broken...
Any chance you could tell us what ROM you had previously and what you were trying to do. What are the details you see in BootLoader Mode?
Dont know
I dont know, I got the device from some one else hspl i cant install it or the application is crashing,
I applyd the offical rom from htc but it hangs at 9% and ad 7/99%
I realy get frustrated by this
Antonius123 said:
I dont know, I got the device from some one else hspl i cant install it or the application is crashing,
I applyd the offical rom from htc but it hangs at 9% and ad 7/99%
I realy get frustrated by this
Click to expand...
Click to collapse
So the chances are that the phone is without a ROM.
Now can you try and get into BootLoader Mode (with phone off, press and hold the Volume Down button then tap the Power button). Then tell us what it says.
I got in the bootloader:
PB81100 HX-BC
SPL-1.42.0000
MicroP(LED) 0x05
MicroP(Touch) 0x50
Upgrade Rom code error
Please try again
in the tob right corner: RUUNBH
ruunbh means it is in flash mode, 1.42.0000 means it is stock spl,
so
get hspl2,
put phone into bootloader,
connect phone to usb,
when 'serial' becomes 'usb' run hspl2,
when it reboots after 'we hacked it', hold vol down so tat you return to bootloader,
spl should now say 1.42.hspl
(or x.xx.hspl depends if you changed it in hspl2 dropdown, doesnt matter if you did or not, so long as it ends .hspl)
run your rom flash over usb. either stock rom.exe or customruu with cooked rom.
i did that and the hspl2 application hangs (i will post the error code in this )
Error code after running hspl2_RUN
critical error
Flow: 00000006
Error Code:00000000
Discription: Unkown
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Dit is de error that i get
i guess your last chance is installing the rom via sd card.
do you know if it was branded?
you can check that by trying to download a rom with the S/N of your phone at htc.com.
the rom you can download, is the right one.
download it, unpack it, copy the .nbh on the sd card, rename it to leoimg.nbh and get your phone into bootloader.
DN41
trying it now,
got serial into htc and now downloading and deploying the file
isnt working
I dont know why but the device go into the color bars again and dont continiu i use a 4 gb sd card
does it start flashing? when does it stop (%)?
any infos shown?
DN41
First i get loading for like 5 minutes then it gos to the bootloader directly
could be the card, that happens on 8gb cards too, loading.... wait wait wait - bootloader.
2gb fat32 4096 (4k) block size for best results.
ok i am a little bit further
i download the hp format tool (i use them to create my own os disks etc)
I formatted the sd card with 4k fat32 and now it is updating so thubs crossd.
Hi update did complete,
It now hangs on the HTC Logo on boot :S (i think it is not my lucky day )
or is it taking first time very very long ?
Okay, so I finally found the WP7 Rom and the new MAGLDR 112 that comes in the zip with it.
It's on DFTs forum.
I've uploaded the text file from DFT's forum which includes the download links for the ROM and MAGLDR 112(included in the ROM's zip file)
It's a pretty simple process if you've already flashed your own NAND Android ROM.
First I suggest you backup your SD card and your current NANDroid.
Then enter your bootloader (hold volume down and power button while device is off)
Connect to your computer and start the RomUpdateUtility provided in the MAGLDR112 folder.
Follow the prompts and update to MAGLDR 1.12
After that, your device should restart.
In MAGLDR 1.12 go to USB flasher and wait for the USB connection.
Then run the DWI (as Admin in Win7/Vista) and follow the prompts to install WP7.
After that the device will reboot and instead of booting into Android it will boot into WP7.
Simple
To activate Windows Live services follow this guide http://forum.xda-developers.com/showthread.php?t=912218
It's pretty straight forward.
hey hey!
i still have win6.5 stock rom installed.
do i need to do anything different like flash it to nand droid rom.
Sorry if the question is a stupid one.I am a real NOOB!
Thanks for guidlines!
elasticity19 said:
i still have win6.5 stock rom installed.
do i need to do anything different like flash it to nand droid rom.
Sorry if the question is a stupid one.I am a real NOOB!
Thanks for guidlines!
Click to expand...
Click to collapse
http://forum.xda-developers.com/showthread.php?t=893948
Follow this guide first, up until the point where it tells you to flash the Android ROM, instead flash the Windows Phone 7 ROM, and don't forget to install MAGLDR 1.12(from the WP7 Rom zip file and not the MAGLDR 1.11 from the link above)
THANKS!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
seriously out of topic question
will your android boot up from SD card if u're running WM7
in eg: copying all the Android folders into SD card, and booting clrad/haret?
My phone wont go into magloader after flashing it, i am simply stuck on the bootup screen.
Any ideas?
xandercom said:
My phone wont go into magloader after flashing it, i am simply stuck on the bootup screen.
Any ideas?
Click to expand...
Click to collapse
Same problem here
DanneG said:
Same problem here
Click to expand...
Click to collapse
Any ideas?
I have tried installing with both a 64bit and 32bit machine as another user suggested that might resolve it.
My next step is going to be reflashing of the NRG rom I installed, see if that will revert and then try again.
xandercom said:
Any ideas?
I have tried installing with both a 64bit and 32bit machine as another user suggested that might resolve it.
My next step is going to be reflashing of the NRG rom I installed, see if that will revert and then try again.
Click to expand...
Click to collapse
no idea, I have triead with a win 7 & win xp machine, same problem.
Everything runs without any problems, exept its stuck on the bootup screen
Do you have HSPL 2.08?
Sent from my HD2 using XDA App
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Sent from my HTC Desire using Tapatalk
Solved it!
Download a new radio
I'm using Leo_RADIO_2.15.50.14 now
http://forum.xda-developers.com/showthread.php?t=611787
Hi, for me I have update to wp7 already but when I plug the USB to my PC the phone it don't show me anything...i can't syn I can't use it as USB drive..so what next that I next to do?
DanneG said:
Solved it!
Download a new radio
I'm using Leo_RADIO_2.15.50.14 now
http://forum.xda-developers.com/showthread.php?t=611787
Click to expand...
Click to collapse
Is it necessary to have that radio? I have the Tmous Leo and I have 2.10.50.26 (Im pretty sure) and I got through the installation process. I havent activated it yet, Im waiting on the downloads of the WPDK and all (slow internet). Everything seems to be working wonderfully except for 1 problem: if my screen is off for more than a minute or two, it wont turn back on and I have to yank the battery and restart my phone. Any way to fix that? So far, setting the screen to never turn off works fine, but that will kill my battery while not plugged in.
Noob Here
Flashed Rom with Leo1024 Rom
Folowed the guides
On boot dft screen hangs
did i brick the phone?
carologist said:
Noob Here
Flashed Rom with Leo1024 Rom
Folowed the guides
On boot dft screen hangs
did i brick the phone?
Click to expand...
Click to collapse
No, probably a bad flash or incompatible SD card. Format your card with "SD card Formatter" by Panasonic then...
a) Reboot and when you see the 1234 on screen hold own Vol UP&DOWN together until it goes past DFT into white screen with instructions, then follow them to reset phone.
b) If that doesnt work try to re-flash via magldr/usb.
If the above fails try a different card.
carologist said:
Noob Here
Flashed Rom with Leo1024 Rom
Folowed the guides
On boot dft screen hangs
did i brick the phone?
Click to expand...
Click to collapse
If the phone starts to loop at the dft screen press and hold volume down and it should stop looping. Any other button may also work. But maybe should do a reflash...
same here, having trouble and constant reboot, I tried to reflash (hold off button, select USB flasher), same thing, but after few attempt of self reboot, I manage to get in, after restart the phone, I get DFT screen constantly self reboot again, but after a few attempt it boot in.
Before that I had freezing problem with stock rom, I was told to use WP7 or android to fix the freezing problem. I seems like I doesn't fix anything at all....
thesame problem i have
its cust staying dft screen what can i do
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Are you using hspl2.08 and a compatible radio?
its cust staying dft screen what can i do
hspl2.08
Radio Leo 2.15.50.14
gogodu5sU said:
Are you using hspl2.08 and a compatible radio?
Click to expand...
Click to collapse
yes i do i am using 2.08 hspl .and i also tried all radios...
Remove your sd and sim card or re-download magldr and leo70 rom, make a task29 and reflash magldr and wp7.
Otherwise idk what it could be.
Just got an HD2 that I am trying to load with wp7. The phone is going to elsalvador with my mom to use down their while on vacation and will stay there but I get stuck on the DFT screen bootlooping as well. When I hold volume down while it does this I get a bootloader similar to the three color that says
leo100 SS-B3
nspl0.96.2250.0 and the LED and TOuch
It also says SD none
partition info v211v413.
Can anyone help me. I have reflashed all using hspl 2.08 and Radio Leo 2.15.50.14?
Hi guys!
My friend got a HD2 which shows this screen when powered on:
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Bootloader reads the following:
Code:
PB81120 SS-B3
SPL-2.08.HSPL 8G XE
0x05
CotullaHSPL 0x50
"Upgrade ROM code error"
"Please try again"
I have no info about the phone's past, can the phone be debricked? I'm also interested if it's a serious problem, or just a matter of reflashing a stock rom?
Thanks in advance:
-Reedim
Try to reflash a stock rom, the previous user must have pulled the usb cable during a flash, causing a bad flash.
**MAKE SURE IF DO FLASH A ROM IT A T-MOBILE USA OR YOU MAY BRICK IT COMPLETELY IF FLASH A .51 RADIO
ROMs can be found in wiki with direct links for your model which is T-Mobile USA (TMOUS)
No, I had the same problem-I had found this site and it worked according to these instructions.
http://miui-germany.de/wp/?page_id=807
I agree with the previous posters. I get this error message a lot when something goes wrong during a flash. Just make sure to flash the correct rom from the tri colored boot menu. Also check if you got the correct radio.
I had this issue, i just mtty'd into it and did Task 2a, 28 and 29 (Not completely necessary) and flashed magldr/clk it worked fine after that, i failed it by flashing the official TMOUS HD2 rom from T-Mobile. It failed at the SPL for me.
Phone's finally here, when i try to flash the stock ROM, it stops at 8% (the phone vibrates 7 times :S ) Tried with both stock ROMs, and with USB and SD too. What should I do now?
Reedim said:
Phone's finally here, when i try to flash the stock ROM, it stops at 8% (the phone vibrates 7 times :S ) Tried with both stock ROMs, and with USB and SD too. What should I do now?
Click to expand...
Click to collapse
IMO you could have a faulty CPU(over-heating failure BGA related)...
You should try put it in a freezer for 15-20 minutes and then try to flash a stock ROM: if you manage that, your CPU is faulty, if not ...another hardware related thing is faulty.
Could a radio change solve this problem maybe? :/
I doubt it..