Hi guys!
My friend got a HD2 which shows this screen when powered on:
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Bootloader reads the following:
Code:
PB81120 SS-B3
SPL-2.08.HSPL 8G XE
0x05
CotullaHSPL 0x50
"Upgrade ROM code error"
"Please try again"
I have no info about the phone's past, can the phone be debricked? I'm also interested if it's a serious problem, or just a matter of reflashing a stock rom?
Thanks in advance:
-Reedim
Try to reflash a stock rom, the previous user must have pulled the usb cable during a flash, causing a bad flash.
**MAKE SURE IF DO FLASH A ROM IT A T-MOBILE USA OR YOU MAY BRICK IT COMPLETELY IF FLASH A .51 RADIO
ROMs can be found in wiki with direct links for your model which is T-Mobile USA (TMOUS)
No, I had the same problem-I had found this site and it worked according to these instructions.
http://miui-germany.de/wp/?page_id=807
I agree with the previous posters. I get this error message a lot when something goes wrong during a flash. Just make sure to flash the correct rom from the tri colored boot menu. Also check if you got the correct radio.
I had this issue, i just mtty'd into it and did Task 2a, 28 and 29 (Not completely necessary) and flashed magldr/clk it worked fine after that, i failed it by flashing the official TMOUS HD2 rom from T-Mobile. It failed at the SPL for me.
Phone's finally here, when i try to flash the stock ROM, it stops at 8% (the phone vibrates 7 times :S ) Tried with both stock ROMs, and with USB and SD too. What should I do now?
Reedim said:
Phone's finally here, when i try to flash the stock ROM, it stops at 8% (the phone vibrates 7 times :S ) Tried with both stock ROMs, and with USB and SD too. What should I do now?
Click to expand...
Click to collapse
IMO you could have a faulty CPU(over-heating failure BGA related)...
You should try put it in a freezer for 15-20 minutes and then try to flash a stock ROM: if you manage that, your CPU is faulty, if not ...another hardware related thing is faulty.
Could a radio change solve this problem maybe? :/
I doubt it..
Related
Hey guys, for usually I don't do this and try to help myself on my own when I brick stuff but this time after trying and failing all possible methods for about 10 hours Iam finally here to ask you what I can do...
------ SOLVED!!!!!!!!!!!!! HALLELUJA GUYS I REVIVED MY MAGIC!!!!! ------------------
SOLUTION:
-> I used the Arabic RUU, which was only SLIGHTLY (But nonetheless somehow!) newer than the Asian RUU I had before!
I checked the size of the RUU and it was 60 MB, thus small enough to might have a suitable system.img!
Then I downloaded it, ran the RUU and checked the temporary files for the ROMs and there was only ROM.zip. I tried to just ran the RUU upgrade but it got stuck again (as always)
NOW I could use the rom.zip from my original RUU (Vodafone Germany, 32B!) and insert in in the Temp.File of the Arabic version, then just run the upgrade as usual.
SO TO ALL WHO GET STUCK WHILE UPDATING: Search for a RUU which contains the ROM in the same way (There are 3: rom.zip, rom.nbh and rom.zip/rom1.zip) and copy your original Files into it! The only thing you need is a newer RUU, then it will run despite the fact it wont install the System img!
But where were you stuck? At which screen?
I was flashing my friends HTC Magic 32A to put a new recovery, hboot and SPL.
When I was upgrading the SPL from 6.xx.08.xx to 6.xx.10.xx (i flashed an update.zip with AmonRA recovery) the flash went OK and then it said: "Reboot to complete upgrade"
So I rebooted, and this image appeared:
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
And now nothing else shows up. Not fastboot, not recovery, nothing. Just this damn icon.
I heard that the solution could be to put a new update.zip on the SDCard, and let the installation of new SPL continue...
Afterall, this update for SPL was an update(3mb), not a complete SPL (20mb)...... But i really don't know what new update.zip to use...
Tried to use a RUU.exe? from the HTC Page or here from the forums?
Ravensysteam said:
Tried to use a RUU.exe? from the HTC Page or here from the forums?
Click to expand...
Click to collapse
From htc.. But phone was not even detected
Well my solution obviously only does work if the phone got bricked by RUU and you get to the RUU screen. Have no clue about your problem tho, Guess you can only try some Update.zips and see what happens
Hi i got a HD2 but it wont start
I tryed difrent accu from a college and his device just start and mine not
Any help ?
Greatings
Marcel
EDIT: I got the device starting up in the color bars(bootloader) But i cant flash it
HD2 wont flash
Hi my previous post that the device wont turn on i closed that one.
I am at the tree color screen but when i want to flash a radio or os then it hangs at 0% also i cant hardspl the device.
I cant use the device at this moment
applied hspl?
must be purely coincidental, and something completely different, but my HD won't start up since this mornming either...
Question: Do you get an orange led while charging? If so, my connector is probably broken...
Any chance you could tell us what ROM you had previously and what you were trying to do. What are the details you see in BootLoader Mode?
Dont know
I dont know, I got the device from some one else hspl i cant install it or the application is crashing,
I applyd the offical rom from htc but it hangs at 9% and ad 7/99%
I realy get frustrated by this
Antonius123 said:
I dont know, I got the device from some one else hspl i cant install it or the application is crashing,
I applyd the offical rom from htc but it hangs at 9% and ad 7/99%
I realy get frustrated by this
Click to expand...
Click to collapse
So the chances are that the phone is without a ROM.
Now can you try and get into BootLoader Mode (with phone off, press and hold the Volume Down button then tap the Power button). Then tell us what it says.
I got in the bootloader:
PB81100 HX-BC
SPL-1.42.0000
MicroP(LED) 0x05
MicroP(Touch) 0x50
Upgrade Rom code error
Please try again
in the tob right corner: RUUNBH
ruunbh means it is in flash mode, 1.42.0000 means it is stock spl,
so
get hspl2,
put phone into bootloader,
connect phone to usb,
when 'serial' becomes 'usb' run hspl2,
when it reboots after 'we hacked it', hold vol down so tat you return to bootloader,
spl should now say 1.42.hspl
(or x.xx.hspl depends if you changed it in hspl2 dropdown, doesnt matter if you did or not, so long as it ends .hspl)
run your rom flash over usb. either stock rom.exe or customruu with cooked rom.
i did that and the hspl2 application hangs (i will post the error code in this )
Error code after running hspl2_RUN
critical error
Flow: 00000006
Error Code:00000000
Discription: Unkown
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Dit is de error that i get
i guess your last chance is installing the rom via sd card.
do you know if it was branded?
you can check that by trying to download a rom with the S/N of your phone at htc.com.
the rom you can download, is the right one.
download it, unpack it, copy the .nbh on the sd card, rename it to leoimg.nbh and get your phone into bootloader.
DN41
trying it now,
got serial into htc and now downloading and deploying the file
isnt working
I dont know why but the device go into the color bars again and dont continiu i use a 4 gb sd card
does it start flashing? when does it stop (%)?
any infos shown?
DN41
First i get loading for like 5 minutes then it gos to the bootloader directly
could be the card, that happens on 8gb cards too, loading.... wait wait wait - bootloader.
2gb fat32 4096 (4k) block size for best results.
ok i am a little bit further
i download the hp format tool (i use them to create my own os disks etc)
I formatted the sd card with 4k fat32 and now it is updating so thubs crossd.
Hi update did complete,
It now hangs on the HTC Logo on boot :S (i think it is not my lucky day )
or is it taking first time very very long ?
Noob Here
Flashed Rom with Leo1024 Rom
Folowed the guides
On boot dft screen hangs
did i brick the phone?
carologist said:
Noob Here
Flashed Rom with Leo1024 Rom
Folowed the guides
On boot dft screen hangs
did i brick the phone?
Click to expand...
Click to collapse
No, probably a bad flash or incompatible SD card. Format your card with "SD card Formatter" by Panasonic then...
a) Reboot and when you see the 1234 on screen hold own Vol UP&DOWN together until it goes past DFT into white screen with instructions, then follow them to reset phone.
b) If that doesnt work try to re-flash via magldr/usb.
If the above fails try a different card.
carologist said:
Noob Here
Flashed Rom with Leo1024 Rom
Folowed the guides
On boot dft screen hangs
did i brick the phone?
Click to expand...
Click to collapse
If the phone starts to loop at the dft screen press and hold volume down and it should stop looping. Any other button may also work. But maybe should do a reflash...
same here, having trouble and constant reboot, I tried to reflash (hold off button, select USB flasher), same thing, but after few attempt of self reboot, I manage to get in, after restart the phone, I get DFT screen constantly self reboot again, but after a few attempt it boot in.
Before that I had freezing problem with stock rom, I was told to use WP7 or android to fix the freezing problem. I seems like I doesn't fix anything at all....
thesame problem i have
its cust staying dft screen what can i do
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Are you using hspl2.08 and a compatible radio?
its cust staying dft screen what can i do
hspl2.08
Radio Leo 2.15.50.14
gogodu5sU said:
Are you using hspl2.08 and a compatible radio?
Click to expand...
Click to collapse
yes i do i am using 2.08 hspl .and i also tried all radios...
Remove your sd and sim card or re-download magldr and leo70 rom, make a task29 and reflash magldr and wp7.
Otherwise idk what it could be.
Just got an HD2 that I am trying to load with wp7. The phone is going to elsalvador with my mom to use down their while on vacation and will stay there but I get stuck on the DFT screen bootlooping as well. When I hold volume down while it does this I get a bootloader similar to the three color that says
leo100 SS-B3
nspl0.96.2250.0 and the LED and TOuch
It also says SD none
partition info v211v413.
Can anyone help me. I have reflashed all using hspl 2.08 and Radio Leo 2.15.50.14?
I need help with this problem. I read the post and have them run what they say, but I still have the problem. When I give the option in MAGLDR "Ad Recovery", I get the following screen "1EFATAL HIT 1". I flashed with several options, I've done task 29, even I did hard reset and I returned the handset to factory defaults. But still the problem. I need help.
diwif said:
I need help with this problem. I read the post and have them run what they say, but I still have the problem. When I give the option in MAGLDR "Ad Recovery", I get the following screen "1EFATAL HIT 1". I flashed with several options, I've done task 29, even I did hard reset and I returned the handset to factory defaults. But still the problem. I need help.
Click to expand...
Click to collapse
Is this your first time trying MAGLDR and android on the HD2? If so do you have HSLP and the correct radio flashed? If you dont know then find a TUT that explains how to go from winmo to andoid tep by step.
Cheers,
Evil.
I have no problems installing Android rom for over a year. Lately install "ICS NexusHD2 CM9 (5.Feb.2012)." In a system reset occurred to me this problem. I've done hard factory reset, I installed HSPL 2, 3, 4, original SPL, etc. I changed several radios. I installed the original rom from sd, etc. MAGLDR I have reinstalled several times, just as with Recovery. No but I think it's internal memory, or not work properly. Do not know if changing the polarity on the battery, as when reversing the polarity on the stack for a PC. The truth is that I think has no solution.
Im right there with you my hd2 did this same thing and I have no answers either..
diwif said:
I have no problems installing Android rom for over a year. Lately install "ICS NexusHD2 CM9 (5.Feb.2012)." In a system reset occurred to me this problem. I've done hard factory reset, I installed HSPL 2, 3, 4, original SPL, etc. I changed several radios. I installed the original rom from sd, etc. MAGLDR I have reinstalled several times, just as with Recovery. No but I think it's internal memory, or not work properly. Do not know if changing the polarity on the battery, as when reversing the polarity on the stack for a PC. The truth is that I think has no solution.
Click to expand...
Click to collapse
tashsru said:
Im right there with you my hd2 did this same thing and I have no answers either..
Click to expand...
Click to collapse
Try this.
Download stock windows mobile rom
Extract LEOIMG.nbh from downloaded wm rom
format sd card
put nbh file onto root of sd card
shut down phone
power on phone and hold vol down + end key to enter bootloader
install stock windows mobile rom which uninstalls hspl and everything else
boot windows mobile
once booted turn off
install hspl again (2.08)
install magldr or clk
install cwm
reboot
install rom
reboot
I think that will fix your problems.
Hello
I followed all your instructions, but the problem persists. I put some pictures of the screens. A pulse is when the option MAGLDR "Ad Recovery", and the other is when I do the partitioning. Not if you serve something. Thanks anyway.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
[/URL][/IMG]
[/URL][/IMG]
diwif said:
Hello
I followed all your instructions, but the problem persists. I put some pictures of the screens. A pulse is when the option MAGLDR "Ad Recovery", and the other is when I do the partitioning. Not if you serve something. Thanks anyway.
[/URL][/IMG]
[/URL][/IMG]
Click to expand...
Click to collapse
:/ sorry I thought it would fix it.
check out this thread
http://forum.xda-developers.com/showthread.php?t=982454
nightmare
I have officially given up.. I think this hd2 is a lost cause I have tried everything and well its strange. I have a stock rom on it and its still the same. it boots bt freezes up after boot no response and only way to shut it off is to pull the battery. so i officially give up..
try sticking the phone in the freezer for couple min and flash it. if it works then u have hardware problem. happened to me when i received my cousins hd2, when i tried to flash it with android i got that e1fatal error. try it, it wont hurt.
I Have Problem with My HD2
on to bootloader but no boot to system i tray to flash with RUU fail...
I itry to flash with SDCARD 0282000 Not Allowed
i try to downgrade fail again...
what should i do
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
This image notification to flash HSPL
Any idea??
did u solve?
zamrong said:
I Have Problem with My HD2
on to bootloader but no boot to system i tray to flash with RUU fail...
I itry to flash with SDCARD 0282000 Not Allowed
i try to downgrade fail again...
what should i do
This image notification to flash HSPL
Any idea??
Click to expand...
Click to collapse
What is this....???
Where is HSPL???
---------- Post added at 05:30 PM ---------- Previous post was at 05:28 PM ----------
Can you please tell me what you want to do???
Do u want to flash custom ROM or what??? If yes thn please flash HSPL and radio 1st.
Your 1st pic showing your phone is in serial mode, get it to the USB mode thn flashing can be done, otherwise issue cannot be solved.
Good luck
zamrong said:
I Have Problem with My HD2
on to bootloader but no boot to system i tray to flash with RUU fail...
I itry to flash with SDCARD 0282000 Not Allowed
i try to downgrade fail again...
what should i do
This image notification to flash HSPL
Any idea??
Click to expand...
Click to collapse
first hspl 2.08>
task29>
radio rom2.15>
install rom
I tray to flash hspl 2.08 fail critical error...
Sent from my R800i using XDA
maybe a bit obvious for me to point out but shouldn't your screen say "USB" at the bottom when it's plugged in ??
I think in most cases ( certainly in mine) when the bootloader appears it says serial at the bottom in the white section ( like in your picture) when you plug in the USB cable that changes to "USB" and only then can you flash HSPL.
Maybe a problem with your cable. I had to replace mine after months of playing around with roms on a NOKIA N8
Good luck