Related
I have problem.. My defy is not turning on..
perhaps the case is my battery is running out when I flash or my motherboard broken,
but I plug defy in USB on the laptop, I see the white led, and I plug into the charger, I see the white led with blinking every second..
when I see white led after plug on usb, can my phone return fine?
sory for bad eng..
Can you enter in BL mode.? VOL UP + POWER (with the phone off) if yes flash a sbf with the same or greater BL. version than you have installed
Sent from my MB525 using XDA
Questions go in the Q&A section
swanster said:
I have problem.. My defy is not turning on..
perhaps the case is my battery is running out when I flash or my motherboard broken,
but I plug defy in USB on the laptop, I see the white led, and I plug into the charger, I see the white led with blinking every second..
when I see white led after plug on usb, can my phone return fine?
sory for bad eng..
Click to expand...
Click to collapse
There might be a chance that your battery is dead and you may have to go the McGyver way! However, give the info LeonardoJegigzem asked...
swanster said:
I have problem.. My defy is not turning on..
perhaps the case is my battery is running out when I flash or my motherboard broken,
but I plug defy in USB on the laptop, I see the white led, and I plug into the charger, I see the white led with blinking every second..
when I see white led after plug on usb, can my phone return fine?
sory for bad eng..
Click to expand...
Click to collapse
Don't worry the same problem happened with me...then i flashed my defy with 2.3.6 sbf by RSD lite and now its working very good...
But my camera still dead and i will find the solution soon...
Sent from my MB525 using xda premium
shaGGy5678 said:
Don't worry the same problem happened with i flashed my defy with 2.3.6 sbf by RSD lite and now its working very good...
But my camera still dead and i will find the solution soon...
Sent from my MB525 using xda premium
Click to expand...
Click to collapse
May be you have green lens camera! If so you will need to root and install mods coz you can't go back to Froyo! There is only one BL6 Froyo which is Chinese!
pranks1989 said:
May be you have green lens camera! If so you will need to root and install mods coz you can't go back to Froyo! There is only one BL6 Froyo which is Chinese!
Click to expand...
Click to collapse
Yup...i have green lens and my defy is already rooted...kindly tell me the next step to get back my camera!!!
Sent from my MB525 using xda premium
LeonardoJegigzem said:
Can you enter in BL mode.? VOL UP + POWER (with the phone off) if yes flash a sbf with the same or greater BL. version than you have installed
Sent from my MB525 using XDA
Click to expand...
Click to collapse
I can't enter on BL, I tried use MCgyver, but nothing happen to my DEFY, and I use another battery I borrow from my friend, nothing happen to.. possible to motherboard crash??
sorry bad eng
swanster said:
I can't enter on BL, I tried use MCgyver, but nothing happen to my DEFY, and I use another battery I borrow from my friend, nothing happen to.. possible to motherboard crash??
sorry bad eng
Click to expand...
Click to collapse
Bro.
Need not to enter in bootloader just download RSD lite and a SBF ...and flash it
Sent from my MB525 using xda premium
shaGGy5678 said:
Bro.
Need not to enter in bootloader just download RSD lite and a SBF ...and flash it
Sent from my MB525 using xda premium
Click to expand...
Click to collapse
really?? can you tell me the step?
How to Unbrick Defy
swanster said:
really?? can you tell me the step?
Click to expand...
Click to collapse
GB works to unbrick ur brick defy
Download Rsdlite from XDA
››Now Download any SBF (link updated below)
>>Run RSDLITE
››Now connect ur Defy
››Press power+Vol up
››Load sbf into RSDLITE
››Hit Flash Wait till it completes
››Now U see Moto Logo (with Transition effect)
››Now if u Stuck on Moto Logo
then do this
=>Remove battery
=>Press Vol down + Powerup (insert battery with continuous key press )
=>now u see Exclamatory mark on Android
=>For GB:
press Vol up N Vol Down simultaneously
=>For Eclair
Touch at right bottom of screen
=>Now You r going in Bootmenu
=>Wipe data clear cache
Njoy
If u want to install Gb on Defy
then u hav to use GB of Defy + works only on Defy Green Lens
+ Defy Red Lens (Chance for Working cam)
i m using it..
Ok Bro
Here is ur link:
http://www.4shared.com/zip/uISOfnuc/451-134_DFP-1321.html
or also u can use
Eclair version for ur brick defy
To unbrick use this link:
http://uploading.com/files/3b18ccb4/JORDN_U3_97.21.51.rar/
*Link are copied from XDA Forum only*
Thanks N NjOY
shaGGy5678 said:
GB works to unbrick ur brick defy
Download Rsdlite from XDA
››Now Download any SBF (link updated below)
>>Run RSDLITE
››Now connect ur Defy
››Press power+Vol up
››Load sbf into RSDLITE
››Hit Flash Wait till it completes
››Now U see Moto Logo (with Transition effect)
››Now if u Stuck on Moto Logo
then do this
=>Remove battery
=>Press Vol down + Powerup (insert battery with continuous key press )
=>now u see Exclamatory mark on Android
=>For GB:
press Vol up N Vol Down simultaneously
=>For Eclair
Touch at right bottom of screen
=>Now You r going in Bootmenu
=>Wipe data clear cache
Njoy
If u want to install Gb on Defy
then u hav to use GB of Defy + works only on Defy Green Lens
+ Defy Red Lens (Chance for Working cam)
i m using it..
Ok Bro
Here is ur link:
http://www.4shared.com/zip/uISOfnuc/451-134_DFP-1321.html
or also u can use
Eclair version for ur brick defy
To unbrick use this link:
http://uploading.com/files/3b18ccb4/JORDN_U3_97.21.51.rar/
*Link are copied from XDA Forum only*
Thanks N NjOY
Click to expand...
Click to collapse
thanks for your trick, but when I press vol up n power, nothing happen to my phone and RSD lite can't detect my phone..
swanster said:
thanks for your trick, but when I press vol up n power, nothing happen to my phone and RSD lite can't detect my phone..
Click to expand...
Click to collapse
Press power and volume up button at same time...and use RSD lite latest version with drivers...try and reply
Sent from my MB525 using xda premium
shaGGy5678 said:
Press power and volume up button at same time...and use RSD lite latest version with drivers...try and reply
Sent from my MB525 using xda premium
Click to expand...
Click to collapse
And if that is not working your battery may have dried of juice!! If that is the case you may have to go the Mc Gyver way! Well same thing happened with me but RSD lite detected my phone and it came alive after flashing SBF with 18% battery left!
Dude earlier you told about your addition battery plz charge the battery in your friends cell then put in your cell then try to connect to RSD lite...
Sent from my MB525 using xda premium
shaGGy5678 said:
Dude earlier you told about your addition battery plz charge the battery in your friends cell then put in your cell then try to connect to RSD lite...
Sent from my MB525 using xda premium
Click to expand...
Click to collapse
RSD din't detect my phone, I use new battery, same RSD not detect my phone..
should I go to SC??
swanster said:
RSD din't detect my phone, I use new battery, same RSD not detect my phone..
should I go to SC??
Click to expand...
Click to collapse
0kkk
First open the RSD lite then connect the cable with phone...
And make sure about your RSD lite and drivers...hope it will work...
Sent from my MB525 using xda premium
i have the same problme and since it happend i had been waiting for the one who is going to help me but no one did ...
now im looking for a new device hopping that someone will fix the defy's brick problme..
sorry 4 my bad lang..
has anybody of you tried epsylons "factory cable" - way, dont know if it may help or is suitable for your problem, but it could be a help
http://forum.xda-developers.com/showthread.php?t=1489289
shaGGy5678 said:
0kkk
First open the RSD lite then connect the cable with phone...
And make sure about your RSD lite and drivers...hope it will work...
Sent from my MB525 using xda premium
Click to expand...
Click to collapse
yeah, I tried that but nothing happen.. thanks for your tutorial..
Hi my power button recently broke and i tried to flash twrp recovery to my working defy with wiui installed which allows to to wake the phone with the volume rocker, it has corrupted my recovery and my defy wont boot into android is my phone bricked as i cant think of anyway to recover it from this. Thanks
morgs640 said:
Hi my power button recently broke and i tried to flash twrp recovery to my working defy with wiui installed which allows to to wake the phone with the volume rocker, it has corrupted my recovery and my defy wont boot into android is my phone bricked as i cant think of anyway to recover it from this. Thanks
Click to expand...
Click to collapse
read this guide: http://forum.xda-developers.com/showthread.php?t=1216982
Boot into Bootloader mode (power-on while holding Vol-Down)
You may need to flash an SBF to get going again.
_ossie_ said:
read this guide: http://forum.xda-developers.com/showthread.php?t=1216982
Boot into Bootloader mode (power-on while holding Vol-Down)
You may need to flash an SBF to get going again.
Click to expand...
Click to collapse
Hi thanks for your reply i cant get into bootloader mode as my power button is broken?
morgs640 said:
Hi thanks for your reply i cant get into bootloader mode as my power button is broken?
Click to expand...
Click to collapse
Pull the battery and reinsert it while holding Vol-Down. This usually works as a power-up.
Do it while connected to a PC. The PC should sound the "device connected" sound.
If the white LED comes on, it usually means the phone is OFF and charging. No LED usually means it's ON and in BL mode (you should get the white text on black screen, but you won't if you have flashed a 'bad' SBF).
Try this a few times.
If nothing else is broken you should be able to get into BL mode and flash an SBF.
But your power button needs to be mechanically fixed at some stage, or your phone isn't going to be much use.
_ossie_ said:
Pull the battery and reinsert it while holding Vol-Down. This usually works as a power-up.
Do it while connected to a PC. The PC should sound the "device connected" sound.
If the white LED comes on, it usually means the phone is OFF and charging. No LED usually means it's ON and in BL mode (you should get the white text on black screen, but you won't if you have flashed a 'bad' SBF).
Try this a few times.
If nothing else is broken you should be able to get into BL mode and flash an SBF.
But your power button needs to be mechanically fixed at some stage, or your phone isn't going to be much use.
Click to expand...
Click to collapse
I have tried all of this already and unfortunately it doesnt get into bootloader mode it just comes up with the moto logo. The phone was working before i tried to update my cwm to twrp i didnt flash an sbf. The power button works fine it must be stuffed on the mainboard i took it apart and the button works fine, why do i need the power button for anyway?
morgs640 said:
I have tried all of this already and unfortunately it doesnt get into bootloader mode it just comes up with the moto logo. The phone was working before i tried to update my cwm to twrp i didnt flash an sbf. The power button works fine it must be stuffed on the mainboard i took it apart and the button works fine, why do i need the power button for anyway?
Click to expand...
Click to collapse
now can you turn on your phone? the power btn works?
try flashing official sbf , root and 2nd-init again.
p.s make sure you have above 20% batt or you gonna spend your time just like me plugging the defy mobo directly to 5 volts.
-Danik- said:
now can you turn on your phone? the power btn works?
try flashing official sbf , root and 2nd-init again.
p.s make sure you have above 20% batt or you gonna spend your time just like me plugging the defy mobo directly to 5 volts.
Click to expand...
Click to collapse
The power button doesnt work but it turns on when battery is inserted, i cant get the phone to pickup in rsd
morgs640 said:
The power button doesnt work but it turns on when battery is inserted, i cant get the phone to pickup in rsd
Click to expand...
Click to collapse
Hold the Volume Up key while inserting the battery.
_ossie_ said:
Hold the Volume Up key while inserting the battery.
Click to expand...
Click to collapse
just goes to moto logo, with usb cable it does the same after about a minute. i can get into the android bootmenu (where u can go into cwm overclock from etc) but recovery doesnt load comes up with missing file error due to me trying to flash twrp
morgs640 said:
just goes to moto logo, with usb cable it does the same after about a minute. i can get into the android bootmenu (where u can go into cwm overclock from etc) but recovery doesnt load comes up with missing file error due to me trying to flash twrp
Click to expand...
Click to collapse
Doesn't bootmenu (Recovery) give you option to reboot into Bootloader? If so, do this and flash an SBF.
_ossie_ said:
Doesn't bootmenu (Recovery) give you option to reboot into Bootloader? If so, do this and flash an SBF.
Click to expand...
Click to collapse
Even if it does, power button is malfunctioning, hence can't select it...
Sent from my MB525 using Tapatalk 2
dbarrera said:
Even if it does, power button is malfunctioning, hence can't select it...
Sent from my MB525 using Tapatalk 2
Click to expand...
Click to collapse
the menu button works to select items in cwm so no problem there, do u mean in bootloader?
_ossie_ said:
Doesn't bootmenu (Recovery) give you option to reboot into Bootloader? If so, do this and flash an SBF.
Click to expand...
Click to collapse
options are
- boot
-cpu
-recovery
-tools
-reboot
dbarrera said:
Even if it does, power button is malfunctioning, hence can't select it...
Click to expand...
Click to collapse
<<< head hits desk >>>
OK so if the phone will boot into recovery it SHOULD also boot into bootloader ?
Maybe I confused OP by saying hold "Vol Down" when I meant "Vol UP" ???
Anyway, OP will probably not get too far without a functional Power button.
_ossie_ said:
<<< head hits desk >>>
OK so if the phone will boot into recovery it SHOULD also boot into bootloader ?
Maybe I confused OP by saying hold "Vol Down" when I meant "Vol UP" ???
Anyway, OP will probably not get too far without a functional Power button.
Click to expand...
Click to collapse
Ok im with you now haha i thought you meant i needed the power button in cwm and i was thinking what for? but i cant get into bootloader anyway so doesnt really matter. I cant get into anything except cwm, holding up just brings up a black light up screen and phone wont recognize in rsd
morgs640 said:
... holding up just brings up a black light up screen and phone wont recognize in rsd
Click to expand...
Click to collapse
Are you SURE? I have had Bootloader work even though nothing shows on screen (when I flashed the wrong SBF). The screen was black but RSD could still "see" the device.
Defy has a locked bootloader (cannot be overwritten), so the fact that you can boot into recovery indicates the bootloader is still there and working. Maybe the problem is in your version of RSD Lite, or your version of drivers installed on the PC, or in your USB cable?
Try uninstalling the drivers from the PC, then rebooting, then attaching the phone and insert battery while holding Vol-Up. This SHOULD reinstall the BL drivers to the PC. Try another USB cable - I have had cables which work for charging but not for data transfer.
_ossie_ said:
Are you SURE? I have had Bootloader work even though nothing shows on screen (when I flashed the wrong SBF). The screen was black but RSD could still "see" the device.
Defy has a locked bootloader (cannot be overwritten), so the fact that you can boot into recovery indicates the bootloader is still there and working. Maybe the problem is in your version of RSD Lite, or your version of drivers installed on the PC, or in your USB cable?
Try uninstalling the drivers from the PC, then rebooting, then attaching the phone and insert battery while holding Vol-Up. This SHOULD reinstall the BL drivers to the PC. Try another USB cable - I have had cables which work for charging but not for data transfer.
Click to expand...
Click to collapse
Alright sound good thanks ill give it a go on my other pc using a different cable, thanks for your continued help with the problem
No go looks like the phone is cooked tried another defy and picks up straight away in rsd on boith pc's and mine doesnt work on either thanks for your help people.
ols help me....defy stuck at black screen...no bootloader
rsd lite recognises through factory cable but while flashing sbf it gives error sending ti rom packets and den it fails.....my stock rom was froyo india.....pls help.....
:crying:
I was running the Vortex ROM for several months now. This morning, my volume rocker wouldn't stop increasing the ringer volume. I couldn't do anything, so I pulled out the battery.
The phone would then boot till the Android exclamation sign and wouldn't go any further. I pulled out the battery several times while at that screen and now it refuses to even go beyond the bootloader. I have drained my battery completely
Please, help
I've got a battery charger that works with any battery. Hopefully, battery won't be an issue now
Android exclamation sign
Click to expand...
Click to collapse
that would be android recovery, press both volume buttons, to continue, wipe cache, reboot
sd_shadow said:
that would be android recovery, press both volume buttons, to continue, wipe cache, reboot
Click to expand...
Click to collapse
As mentioned in the OP, I don't see the android recovery now. All I see is the "Google" logo. This replaced the Motorola logo since I had flashed the Vortex ROM.
Powering on the phone with both volume keys pressed takes me to a screen that reads "Bootloader 30.04. Baterry OK. Ok to program. Connect USB data cable."
press and hold home, while powering on to get triangle, !, and android andy
Sent from my XT862 using xda premium
sd_shadow said:
press and hold home, while powering on to get triangle, !, and android andy
Sent from my XT862 using xda premium
Click to expand...
Click to collapse
Nothing happens
I tried to SBF to .621 using both RSD lite and linux. Both installations look successful but I'm still stuck at the M logo
melv1nratedr said:
Nothing happens
Click to expand...
Click to collapse
what does that mean, doesn't power on? goes to m screen?
sd_shadow said:
what does that mean, doesn't power on? goes to m screen?
Click to expand...
Click to collapse
Goes to the M screen directly
well i guess it's time to flash .sbf
do you know what system version was on phone
4.5.602 or 4.5.621?
use DX ezSBF Linux solution to your Windows/RSD lite problems
labyrinths coniby
sd_shadow said:
well i guess it's time to flash .sbf
do you know what system version was on phone
4.5.602 or 4.5.621?
use DX ezSBF Linux solution to your Windows/RSD lite problems
Click to expand...
Click to collapse
It was on .621. As mentioned in an earlier post, I tried SBFing. It was successful except when it rebooted, it was still stuck at the M logo. Could this be a button issue?
i forgot the s-on
i forgot the s-on and installed a rom what to do now its stuck in bootloader pls help my phone is htc sensation xe
niktb said:
i forgot the s-on and installed a rom what to do now its stuck in bootloader pls help my phone is htc sensation xe
Click to expand...
Click to collapse
Try posting here Sensation Q&A, Help ..
melv1nratedr said:
It was on .621. As mentioned in an earlier post, I tried SBFing. It was successful except when it rebooted, it was still stuck at the M logo. Could this be a button issue?
Click to expand...
Click to collapse
this is old but you had to format data...
I Tried To Flash A GPU Overclocking Kernal Over My CPU Overclocking Kernal But It Had Failed So When I Pressed Reboot System It's Not Turning On Please Help.
Can you get into recovery by holding power+volume up?
KiiDPoLo said:
I Tried To Flash A GPU Overclocking Kernal Over My CPU Overclocking Kernal But It Had Failed So When I Pressed Reboot System It's Not Turning On Please Help.
Click to expand...
Click to collapse
what kernel did u flash?
mic213 said:
what kernel did u flash?
Click to expand...
Click to collapse
I think its safe to say that it wasnt compatible with the XT907
Nope It's Not Turning On At All, Im Gonna Try Leaving It Charging. It Was Some ICS Linpack GPU Kernal.
Here's The Link: http://rootzwiki.com/topic/33830-der-kernel-trinity-gst-vzw-ics/page__st__30
Also Im Have TWRP Recovery V2.3.2.3 and On This Rom: http://forum.xda-developers.com/showthread.php?t=2355916
KiiDPoLo said:
Nope It's Not Turning On At All, Im Gonna Try Leaving It Charging. It Was Some ICS Linpack GPU Kernal.
Here's The Link: http://rootzwiki.com/topic/33830-der-kernel-trinity-gst-vzw-ics/page__st__30
Also Im Have TWRP Recovery V2.3.2.3 and On This Rom: http://forum.xda-developers.com/showthread.php?t=2355916
Click to expand...
Click to collapse
Yeah, bad kernel. That's designed for a SGS3 and CM9 ROMs. With that being said, it won't boot all? The bad kernel shouldn't prevent you from booting into recovery, but like Panther said, your battery may be dead. Leave it on the charger for a while and see what happens. Use Panther's button combo to boot straight into recovery and restore a backup. You can also try holding all three buttons to get into the fastboot menu. Once in the menu, use vol- to go to your choice and vol+ to select your option. Good luck and let us know what happens.
RikRong said:
Yeah, bad kernel. That's designed for a SGS3 and CM9 ROMs. With that being said, it won't boot all? The bad kernel shouldn't prevent you from booting into recovery, but like Panther said, your battery may be dead. Leave it on the charger for a while and see what happens. Use Panther's button combo to boot straight into recovery and restore a backup. You can also try holding all three buttons to get into the fastboot menu. Once in the menu, use vol- to go to your choice and vol+ to select your option. Good luck and let us know what happens.
Click to expand...
Click to collapse
I've Been Charging It For A Few Hours Now. Nothings Happening, Not Even The Charging LED Comes On But Imma Leave It To Charge For A Little Longer; I Switched Outlets.
Still Not Coming On and I Flashed It AT A Full Battery.
RikRong said:
Yeah, bad kernel. That's designed for a SGS3 and CM9 ROMs. With that being said, it won't boot all? The bad kernel shouldn't prevent you from booting into recovery, but like Panther said, your battery may be dead. Leave it on the charger for a while and see what happens. Use Panther's button combo to boot straight into recovery and restore a backup. You can also try holding all three buttons to get into the fastboot menu. Once in the menu, use vol- to go to your choice and vol+ to select your option. Good luck and let us know what happens.
Click to expand...
Click to collapse
Nothing's Happening. No LED, No Signs Off Life, IDK What To Do....!!!!!!!!!!!!!!!!!
KiiDPoLo said:
Nothing's Happening. No LED, No Signs Off Life, IDK What To Do....!!!!!!!!!!!!!!!!!
Click to expand...
Click to collapse
Put it on a charger. Then if you can't get bootloader menu to come on (normal pwr, recovery....).
Then you clobbered the partitions. Got insurance?
aviwdoowks said:
Put it on a charger. Then if you can't get bootloader menu to come on (normal pwr, recovery....).
Then you clobbered the partitions. Got insurance?
Click to expand...
Click to collapse
Okay Thanks, and Nope
KiiDPoLo said:
Okay Thanks, and Nope
Click to expand...
Click to collapse
not sure if you resolved you issue, but try again to get to recovery - press and hold all 3 buttons (power + volume up + volume down), release only the power button after 5 seconds and wait for the recovery screen to appear (if not, try releasing the volume buttons, then press the volume down button once, then the volume up button once).
At About 2:30 AM This Morning The Charging LED Finally Came On But It's Green So I Guess It Has A Full Battery, Not Sure and Whenever I Try To Boot Into Recovery The Light Comes Off.
KiiDPoLo said:
At About 2:30 AM This Morning The Charging LED Finally Came On But It's Green So I Guess It Has A Full Battery, Not Sure and Whenever I Try To Boot Into Recovery The Light Comes Off.
Click to expand...
Click to collapse
that's a good sign that the battery light came on. getting into recovery can be tricky, so keep trying. you might need to get there blindly - basically, assume that you cannot see the screen, and press the right buttons to get into it. this has happened to me before.
jco23 said:
that's a good sign that the battery light came on. getting into recovery can be tricky, so keep trying. you might need to get there blindly - basically, assume that you cannot see the screen, and press the right buttons to get into it. this has happened to me before.
Click to expand...
Click to collapse
Okay So Do My Phone Need Any Source Of Power To Boot And When I Boot Into Recovery Will The Screen Turn On ????
KiiDPoLo said:
Okay So Do My Phone Need Any Source Of Power To Boot And When I Boot Into Recovery Will The Screen Turn On ????
Click to expand...
Click to collapse
I would leave it plugged in. Once you get to the twrp screen, it should appear.
Sent from my XT907 using xda app-developers app
jco23 said:
I would leave it plugged in. Once you get to the twrp screen, it should appear.
Sent from my XT907 using xda app-developers app
Click to expand...
Click to collapse
Okay Thanks Alot Man For All The Help. Im Going To Try Right Now.
It still Hasnt Come Back On. Can You tell Me Exactly How You Fixed Yours and How Yours Got Bricked ??????:crying::crying::crying::crying::crying:
jco23 said:
I would leave it plugged in. Once you get to the twrp screen, it should appear.
Sent from my XT907 using xda app-developers app
Click to expand...
Click to collapse
It still Hasnt Come Back On. Can You tell Me Exactly How You Fixed Yours and How Yours Got Bricked ??????
KiiDPoLo said:
It still Hasnt Come Back On. Can You tell Me Exactly How You Fixed Yours and How Yours Got Bricked ??????
Click to expand...
Click to collapse
21 days later?
Sent from my XT907 using xda app-developers app
jco23 said:
21 days later?
Sent from my XT907 using xda app-developers app
Click to expand...
Click to collapse
I Slacked Off For Awhile. Here's Exactly What My Phone Is Doing. This Guy Has The Same Problem:http://www.youtube.com/watch?v=kFxL5-kIdSs
Its stuck on the bootloader with errors listed on the title
Flash a newer sbf(like dfp 231)
Sent from my MB526 using Tapatalk
Thats the problem
thekguy said:
Flash a newer sbf(like dfp 231)
Sent from my MB526 using Tapatalk
Click to expand...
Click to collapse
Because its stuck on bootloader my phone won't connect to my laptop so im am not able to flash me defy+
Is there some way?
Just take out the battery, and hold volume up before powering up
Sent from my MB526 using Tapatalk
thekguy said:
Just take out the battery, and hold volume up before powering up
Sent from my MB526 using Tapatalk
Click to expand...
Click to collapse
How would it then turn on? Can you please instruct me with steps? When i take out the battery whats after that ?
Power on normally, holding the power button
Sent from my MB525 using Tapatalk
Wait,wait,wait...........
So i:
1)Take out the battery from back
2)Power on using the vol up button. How would it turn on without battery?
3)......... idk what to do
It won't turn on without the battery, so put it back, press volume up and then power button
Sent from my MB526 using Tapatalk
So i take out the battery then hold/press the vol up button, then put battery back in while holding vol up button? then hold vol up button then without releasing the vol up button i hold the power button? for how long?
Hope im not asking stupid questions
You can just search for a video guide. Although your current understanding is correct. The time to hold the volume up button is till you get to the boot loader screen ~3 seconds
Sent from my MB526 using Tapatalk
Will this load my to bootloader 9.10 but with no error? Just a simple bootloader? ~~~YES~~?
If yes then doesn't work my computer won't detect my phone even the motorola driver, anyway you can help with that?
Maybe you should be able to flash from the error screen itself! Use admin mode and latest rsdlite and drivers, as per your system
Sent from my MB526 using Tapatalk
Im sorry what is admin mode and how to enable it? and i have tried to connect it from the error screen to my computer but it wont detect my phone.
Which os do you have on the computer? If windows vista or higher, right click on rsdlite and click on run as administrator
Could you reach the BL screen? Try the instructions I gave or a video guide
Sent from my MB526 using Tapatalk
Doesn't work
Eliminate007 said:
Doesn't work
Click to expand...
Click to collapse
it worked for me with the same error
1/ install the latest phone drivers on your computer
2/ run rsdlite on your computer (don't connect your phone)
3/ on your phone : hold volume up then powering up
4/ when your phone is in the bootloader, connect it on your computer
5/ rsdlite should recognize your phone after few seconds
6/ flash a stock rom
Do i run rsdlite as an administrator?
Won't recognize/find my phone
Eliminate007 said:
Won't recognize/find my phone
Click to expand...
Click to collapse
try with another computer...
I am currently using Windows 8, probably somethings wrong with that?