Related
My friend gave me his HD2. The problem is he doesn't remember the lock screen code. I have an Evo 4G and figured I could load the HD2 into the "hboot" and reset it. I figured out the buttons I have to push and sadly its not working. I hit the Vol. Up and Vol. Down + the power button and all it does is start up. I haven't seen the multicolored screen I'm supposed to be seeing. I don't care how it has to be done, I just need this phone unlocked lol.
Thanks, Tyler
31794ty said:
My friend gave me his HD2. The problem is he doesn't remember the lock screen code. I have an Evo 4G and figured I could load the HD2 into the "hboot" and reset it. I figured out the buttons I have to push and sadly its not working. I hit the Vol. Up and Vol. Down + the power button and all it does is start up. I haven't seen the multicolored screen I'm supposed to be seeing. I don't care how it has to be done, I just need this phone unlocked lol.
Thanks, Tyler
Click to expand...
Click to collapse
To perform a HTC HD2 Leo hard reset with buttons you should turn off the phone, press and hold the VOLUME UP and VOLUME DOWN buttons, then press the END/POWER button shortly and release it. After that follow the instructions.
I tried that and it just starts up. It never goes into the reset screen.
Take the battery cover off and make sure your getting a good amount of pressure on both volume buttons.
If its still not working sounds like you might have a broken button.
Can you get to bootloader by holding only vol down and then powering on?
I tried it and it didn't work. crap...
Any other ways to get this thing reset?
i have the same problem.
i cannot connect to any pc and cannot get the phone into reset mode.
im running energyROM which has problems. it won't turn off.
ideas how to wipe this sucker?
azreal8 said:
i have the same problem.
i cannot connect to any pc and cannot get the phone into reset mode.
im running energyROM which has problems. it won't turn off.
ideas how to wipe this sucker?
Click to expand...
Click to collapse
Yes go to settings, I can not remember wich one it is under but it is a option in settings somewhere to do a factory reset that is what you are looking for. I am running Android now so I can not find it in my HD2, but it is there just look for it.
azreal8 said:
i have the same problem.
i cannot connect to any pc and cannot get the phone into reset mode.
im running energyROM which has problems. it won't turn off.
ideas how to wipe this sucker?
Click to expand...
Click to collapse
Unpack official (no Custom ROMs working) ROM to a folder on your PC, rename file RUU_signed.nbh to Leoimg.nbh, copy it to root directory of microSD card (preferrably less than 2GB ands Fat32 formatted), insert it in your phone (turned OFF), hold VolDown key and shortly press power button. Phone will start in bootloader mode and you have to press power button again to start flashing.
After end of flashing make a HR and enjoy.
T-Macgnolia said:
Yes go to settings, I can not remember wich one it is under but it is a option in settings somewhere to do a factory reset that is what you are looking for. I am running Android now so I can not find it in my HD2, but it is there just look for it.
Click to expand...
Click to collapse
It is in the system settings called "Wipe Device" in my NRG ROM. I've seen it called "Clear Storage".
stevedebi said:
It is in the system settings called "Wipe Device" in my NRG ROM. I've seen it called "Clear Storage".
Click to expand...
Click to collapse
Thanks for the assist on that one man. Me not having Win Mo on my HD2 kinda makes it hard to give precise answers on Win Mo now
im having the same issue.
i wipe the device using the menus but it's still stuffed.
it won't get to the reset screen when i press the vol up/down and press the power
button OR when using other methods.
my phone is cactus.
funnily i'm running nrg as well.
Check post #9 and try to follow intructions.
azreal8 said:
im having the same issue.
i wipe the device using the menus but it's still stuffed.
it won't get to the reset screen when i press the vol up/down and press the power
button OR when using other methods.
my phone is cactus.
funnily i'm running nrg as well.
Click to expand...
Click to collapse
Flash a new NRG ROM, and do NOT use XDA_UC. A flash removes everything in memory. Then you can see what is causing your issues by manually installing the cab files in XDA_UC. You should also install everything possible to the SD card to save space in system memory.
Also, check the memory BEFORE restoring contacts & etc. Those .vol files in the root directory can take up a lot of space.
pvii said:
Unpack official (no Custom ROMs working) ROM to a folder on your PC, rename file RUU_signed.nbh to Leoimg.nbh, copy it to root directory of microSD card (preferrably less than 2GB ands Fat32 formatted), insert it in your phone (turned OFF), hold VolDown key and shortly press power button. Phone will start in bootloader mode and you have to press power button again to start flashing.
After end of flashing make a HR and enjoy.
Click to expand...
Click to collapse
I can flash the stock ROM by using 16GB Class10 card successfully.
The card was formatted by HD2 previously.
pvii said:
Unpack official (no Custom ROMs working) ROM to a folder on your PC, rename file RUU_signed.nbh to Leoimg.nbh, copy it to root directory of microSD card (preferrably less than 2GB ands Fat32 formatted), insert it in your phone (turned OFF), hold VolDown key and shortly press power button. Phone will start in bootloader mode and you have to press power button again to start flashing.
After end of flashing make a HR and enjoy.
Click to expand...
Click to collapse
You can flash a custom ROM via SD card just the same as a official ROM it does not matter. You still have to have HSPL on hour HD2 first though or it will fail.
thx guys...
i can get it to the boot screen now.
must have had gunk build-up in the buttons or something.
i have downloaded the "T-Mobile_HD2_MR_Software_3.14.531.1" rom from T-mobile.
it's an .EXE file though.
QN: how do i get the RUU_signed.nbh as i need to reflash from my SD card.
azreal8 said:
thx guys...
i can get it to the boot screen now.
must have had gunk build-up in the buttons or something.
i have downloaded the "T-Mobile_HD2_MR_Software_3.14.531.1" rom from T-mobile.
it's an .EXE file though.
QN: how do i get the RUU_signed.nbh as i need to reflash from my SD card.
Click to expand...
Click to collapse
Rename the .exe to .zip and then you can right click it and view the contents of the file. You will see the RUU file you need to copy and rename.
thx.
i'm now at the red, green, blue and white screen after holding down the vol and pressing power on.
i cannot get it to get to the boot loader stage to flash the image though.
the screen stays on
"pB881120 SS-B3
SPL-2.08.HSPL 8G XE
0x5
cotullaHSPL 0x40"
Serial"
any ideas where i've gone wrong?
azreal8 said:
thx.
i'm now at the red, green, blue and white screen after holding down the vol and pressing power on.
i cannot get it to get to the boot loader stage to flash the image though.
the screen stays on
"pB881120 SS-B3
SPL-2.08.HSPL 8G XE
0x5
cotullaHSPL 0x40"
Serial"
I
any ideas where i've gone wrong?
Click to expand...
Click to collapse
If you took the RUU_signed.nbh file and copied it then renamed it leoimg.nbh and placed it on the root of your SD card. (it has to be on the root of our SD card) Then the bootloader should automaticly say searching on the screen and then promt you to press the end button if you want to flash the image.
Just in case you do not know what the root of your SD card is. It is what you see when you first pull up your SD card in your phone or on the computer. The leoimg.nbh can not be in a folder on your SD card.
hi guys i flashed my htc hd2 wm6.5 to nand android rom in 1st 1 week of usage i have no problem and enjoyed the nand android rom in my htc hd2 until one day my hd2 hang and when i reboot my unit it was hang on splash screen only....
i reflashed it using magdlr ver. 1.11 into the same nand rom im using but i have no luck...it still stock on tje android splash screen...what will i do guys?
im planning to flash it to wm6.5 rom,but what will i do?it never boot on tri color screen it only boot on magdlr screen
and how can i flash it wm6.5 rom cook or stock rom i want to revert it back to wm6.5
my hd2 running on gingerbread 2.3.3 nand(V1.8) rom before it malfunction..
Well, my forensic analysis has come up with the following technical and somewhat difficult solution to your present problem: "Click the search button"
Now I know it may sound intimidating, but I tested that feature out for you and came up with this:
http://forum.xda-developers.com/showthread.php?t=905841
matt
Shut down completely your phone (remove batter for 15 sec too)
Place battery back and now hold volume down button.
Still hold volume down button and switch on your phone.
You get 3 color screen.
Now attach your usb cable and connect it to PC
Find on this forum your phone stock win mobile rom (link to officila roms thread)
Run stock win 6.5 rom exe (this is sample name: RUU_Leo_S_HTC_WWE_EastEurope_3.14.479.2_Radio_15.42.50.11U_2.15.50.14_LEO_S_Ship.exe)
Follow instructions on your PC screen. On final your phone reboots.
Enjoy your stock phone.
hi datasoft thanks for the quick reply...
i try your suggestion to enter into bootloader mode but it booted on the magldr screen...
can i flash wm6.5 rom into magdlr usb flasher?
siapelbo said:
hi dasoft thanks for the quick reply...
i try your suggestion to enter into bootloader mode but it booted on the magldr screen...
Click to expand...
Click to collapse
Switch off, hold vol down button in and switch on.
As ClydeB1, states you must hold the vol down only and not hold the power button.
siapelbo said:
hi dasoft thanks for the quick reply...
i try your suggestion to enter into bootloader mode but it booted on the magldr screen...
Click to expand...
Click to collapse
when you get ready to power back on you have to hold volume down and keep holding it while is booting and it should switched to the tricolored screen, plug the usb cable and it should say usb at the bottom when it connects, and if you have hardspl which I know you have after running android, you can use any custom winmo6.5 rom it doesn't have to be an official rom.
can i flash wm6.5 rom into magdlr usb flasher?
No, flash from bootloader.
awts...i cant enter into booloader mode....im so sure what im doing i sure i follow the instructions of you guys....holding down the vol button and switch on
Are you holding it at the bottom of the button and not in the middle or top, ie as if you are turning the volume down?
I don't think you can flash WM6.5 with flasher. You have to restore from recovery screen by remove battery and restore.
ClydeB1 said:
Are you holding it at the bottom of the button and not in the middle or top, ie as if you are turning the volume down?
Click to expand...
Click to collapse
yeah im sure i was holding down the volume botton and switch the power on
Does the vol down button work normally in the Android rom or when moving around in magldr. To be sure, remove the battery and leave it out for 10 minutes then put the battery back, leave the cover off and try again.
I have heard of one or two users who have also had a problem where the vol down button stopped working. If that is the case there is no way back AFAIK.
ClydeB1 said:
Does the vol down button work normally in the Android rom or when moving around in magldr. To be sure, remove the battery and leave it out for 10 minutes then put the battery back, leave the cover off and try again.
I have heard of one or two users who have also had a problem where the vol down button stopped working. If that is the case there is no way back AFAIK.
Click to expand...
Click to collapse
volume botton is perfectly working it work around in magdlr mode actually i flashed my hd2 into android rom right now flashing is done without problems, but its not boot normarly it boot only in splash screen....
can you guys post a link of task 29...i will try this method and flash stock rom
but the main problem is i cant enter into bootloader mode
I use this tool for Task29 - http://forum.xda-developers.com/showthread.php?t=917807
Once you run Task29 though it will wipe the NAND memory and magldr and if you can't get back to bootloader mode then you will be stuck on the splashscreen.
Hi,
I'm also having problems, but in my case the progress bar on my phone when installing the new ROM stops at 0% and will stay there indefinably. On my computer a connection problem will be raised.
The same happens with task29.
I've also tried decompressing ROM Utility, putted leoimg.nbh on my 2GB fat32 formatted sdcard, hold down the volume key.
I will get a new screen with "Loading..." on it, but it freezes there.
So, I have no idea what I'm doing wrong.
Any help will be appreciated.
Regards,
temporary_24 said:
Hi,
I'm also having problems, but in my case the progress bar on my phone when installing the new ROM stops at 0% and will stay there indefinably. On my computer a connection problem will be raised.
The same happens with task29.
I've also tried decompressing ROM Utility, putted leoimg.nbh on my 2GB fat32 formatted sdcard, hold down the volume key.
I will get a new screen with "Loading..." on it, but it freezes there.
So, I have no idea what I'm doing wrong.
Any help will be appreciated.
Regards,
Click to expand...
Click to collapse
Are you sure you still have hspl installed? In bootloader, check your spl version- it should end in hspl.
ClydeB1 said:
Are you sure you still have hspl installed? In bootloader, check your spl version- it should end in hspl.
Click to expand...
Click to collapse
Hi,
Yes. I had one with a 8 on it. I've installed the other, and it worked (or the other way). Thanks.
Regards,
guys my phone revive with a jtag procedure i went to a technician shop here in the phillipines
my phone running in stock rom again...
I just bought an HD2 with windows phone 7 already installed. The guy i bought it from said that the phone came like that from the previous owner.
From what I can tell, windows phone 7 has been flashed to the nand/internal memory.
Can someone point me in the direction of where to look to remove this OS so that I can install the other wonderful Rom's developed for the HD2 (android, meego, etc)?
I've been looking around but i'm a little lost.
Thanks!
Personally i would seriously consider taking the HD2 back to its stock defaults and then work forward, the problem of using someone elses work is that you dont actually learn anything, which is what this commuinity is all about
So if you want my advice do an SD card flash of a stock ROM for your device
first things first, go to HTCs website
http://www.htc.com/europe/supportdownloadlist.aspx?p_id=297&act=sd&cat=all
grab yourself a stock ROM (if you have a 1024MB version of the HD2 then be careful!)
extract the file you downloaded, use winrar or 7zip
- Take the "RUU_signed.nbh" and copy it to a blank SD card .
- Rename it to "leoimg.nbh"
- put that SD card in the HD2
- Reset the device while pressing the volume down button.
- Follow directions
that should perform an SD card flash, meaning it will remove absolutely everything and start from scratch, ie Windows Mobile
you can then decide what you want to install and go from there
as a rule the process is HSPL>RADIO>(MAGLDR)>ROM
http://forum.xda-developers.com/showthread.php?t=914924
has some general guides
but as a rule you should really just do to the thread of your chosen OS, that should have some stickys on how to do things and dont forget the wiki!
Thanks for your reply!
I seem to be stuck, when i hold "volume down + power" I get into this:
aMAGLDR V1.12
Boot Menu
1.Boot WPH
2.Boot AD SD
3.Boot AD NAND
4.USB Mass Stg
5.USB Flasher
6. USB TTY
7. AD Hardreset
8.Tetris
9.Servies
10. Reset
11. Powerdown
Can I flash the 6.5 Rom from here?
aludus said:
Thanks for your reply!
I seem to be stuck, when i hold "volume down + power" I get into this:
aMAGLDR V1.12
Boot Menu
1.Boot WPH
2.Boot AD SD
3.Boot AD NAND
4.USB Mass Stg
5.USB Flasher
6. USB TTY
7. AD Hardreset
8.Tetris
9.Servies
10. Reset
11. Powerdown
Can I flash the 6.5 Rom from here?
Click to expand...
Click to collapse
nope!
your holding down the power button arent you?
take out the battery
hold the vol DOWN key
put the battery in (keep holding down vol down)
then "tap" power button (push and let go) the phone will vibrate a bit
keep holding down the vol down key until the tri colour screen comes on, if you copied the .nbh file and renamed it too your SD card it "should" allow you to install it
i tried it to it stays on red green blue white serial.
i have installed win7 but want to loose it
aludus said:
Thanks for your reply!
I seem to be stuck, when i hold "volume down + power" I get into this:
aMAGLDR V1.12
Boot Menu
1.Boot WPH
2.Boot AD SD
3.Boot AD NAND
4.USB Mass Stg
5.USB Flasher
6. USB TTY
7. AD Hardreset
8.Tetris
9.Servies
10. Reset
11. Powerdown
Can I flash the 6.5 Rom from here?
Click to expand...
Click to collapse
afraid not !!
and are you sure you held down the volume down button before pressing the power key !!
cos if you did....i am sorry to say...but yes...i had this issue in the past where i was not at all able to go into the bootloader..the one with the 3 color screen !!
tried everything...finally succeeded !! in case you have this issue...i shall tell you how i was finally able to get into bootloader and flash a stock/custom ROM.
ruthlessboy said:
i tried it to it stays on red green blue white serial.
i have installed win7 but want to loose it
Click to expand...
Click to collapse
yea...so once when you are on the 3 color screen why dont you simply go ahead connect your USB and flash a custom ROM ???
or if you want stock...copy the .nbh file in your SD Card...and the flashing will start automatically...get it ???
Whats your reason for wasnting to remove WP7?
I personally think its better than most roms, and a about tied with the energy rom.
try flashing Yukis V5 and you might prefer WP7
no connection
backlashsid said:
afraid not !!
and are you sure you held down the volume down button before pressing the power key !!
cos if you did....i am sorry to say...but yes...i had this issue in the past where i was not at all able to go into the bootloader..the one with the 3 color screen !!
tried everything...finally succeeded !! in case you have this issue...i shall tell you how i was finally able to get into bootloader and flash a stock/custom ROM.
yea...so once when you are on the 3 color screen why dont you simply go ahead connect your USB and flash a custom ROM ???
or if you want stock...copy the .nbh file in your SD Card...and the flashing will start automatically...get it ???
Click to expand...
Click to collapse
i did all of that but when it comes to flashing it stays on zero and wont flash giving an error
cant put the phone in three color state with vol down + power.
any other way to flash magldr 1.13????
What do you mean you can enter the 3 color state? Do you have any issues with your hardware buttons?
lqtdc said:
cant put the phone in three color state with vol down + power.
any other way to flash magldr 1.13????
Click to expand...
Click to collapse
You should really get your volume button checked. If its a hardware problem, then it can be fixed. Otherwise its bricked
If you have fastboot installed on your computer you can..
Extract the zimage from the zip file
then while phone is on and connected via usb (adb debugging on)
adb reboot-bootloader
then when in bootloader mode
fastboot flash zimage zimage
fastboot reboot
Hope this helps..
smokers said:
What do you mean you can enter the 3 color state? Do you have any issues with your hardware buttons?
Click to expand...
Click to collapse
no the button work ok. when i press in magldr 1.11 works ok.
shanman-2 said:
If you have fastboot installed on your computer you can..
Extract the zimage from the zip file
then while phone is on and connected via usb (adb debugging on)
adb reboot-bootloader
then when in bootloader mode
fastboot flash zimage zimage
fastboot reboot
Hope this helps..
Click to expand...
Click to collapse
sorry, to do this i have to be in android, dont???
Yep
Sent from my Nexus One using xda premium
there is a chance that the problem was the radio???
i dont check the radio. any way to flash tne 2.15 radio without the 3 color screen???
shanman-2 said:
Yep
Sent from my Nexus One using xda premium
Click to expand...
Click to collapse
sorry but i dont have a android to flash without recovery
lqtdc said:
there is a chance that the problem was the radio???
i dont check the radio. any way to flash tne 2.15 radio without the 3 color screen???
Click to expand...
Click to collapse
No.
Have you got the hd2 Nand toolkit?
What s the set up on the phone?
Spl etc
Sent from my Nexus One using xda premium
i have the 2.08 SPL or HSPL i dont remenber but i can put the magldr 1.11 with the romutility from windows but now i cant put in bootloader screen to put the magldr 1.13. i dont check the value of the radio.
Just in case ..are you holding volume down button and pressing and releasing power button while still holding volume button?
It really looks like there is a prob with the volume. As was said already it can be fixed
A cracked volume ribbon cable is not uncommon! !
Sent from my Nexus One using xda premium
the button is not the problem. when the magldr 1.11 loads the button works ok.
Magldr does not change the radio!
What exactly did you so?
Sent from my Nexus One using xda premium
i dont check the radio when install the magldr 1.11.
first i install the 2.08 HSPL, then with the ROMUpdateUtility install MAGLDR 1.11.
i never can put the phone in bootloader mode, that is my problem. i dont know what is the radio
i would suggest making a clear install using the task29 or WM1.66 instal ect.
you have to hold the vol down button while loading
I hav had a problem with magldr1.13 which was caused by the radio - it didnt want to install on the 2.15.50.14 radio and i have had to downgrade my radio, install magldr1.13 and the update the radio to the 2.50.15.14.
but still consider a fresh install of all things to eliminate some stuff staying in the nand memory after such things ...
my problem is i cant put the phone in bootloader mode (Vol Down + Power).
Man, download original Windows 6.5 ROM with Radio.
And run it. it doesn't need push any button. it sends you to 3-colored screen and installs win 6.5 ROM.
Later you can try magldr again or try your volume or power button.
powerofthink said:
Man, download original Windows 6.5 ROM with Radio.
And run it. it doesn't need push any button. it sends you to 3-colored screen and installs win 6.5 ROM.
Later you can try magldr again or try your volume or power button.
Click to expand...
Click to collapse
I don't think auto loading to bootloader works in magldr.
lqtdc said:
the button is not the problem. when the magldr 1.11 loads the button works ok.
Click to expand...
Click to collapse
If your volume button works then try to install an WP7 or android rom through dft. Why do you need to go into bootloader at the moment?
You seem stuck and may have a bricked phone, try this
hengsheng120 said:
I don't think auto loading to bootloader works in magldr.
If your volume button works then try to install an WP7 or android rom through dft. Why do you need to go into bootloader at the moment?
Click to expand...
Click to collapse
Seems you are stuck, maybe you want to try this:
1. Try to start your phone by holding Volume Down and then press the power button. Keep pressing the Volume down. You should you see the four-color (red, green, blue, white) bootloader screen
2. Check that it says 2.08.HSPL (if not, you should start by flashing the correct HSPL by connecting phone by USB and using HSLP4.exe (run as Administrator in Windows)
3. If you have the correct HSPL check that you have 2.15.50.14 Radio ROM installed. If not, you cannot proceed. (Tip: check every file you wodnload if has been correcty received)
4. If all the above things are correct you can flash MAGLDR 1.3) Still using Voluime Down and powes and the four-color (red, green, blue, white) bootloader screen
5. Now you can boot the phone by pressing and holiding down power. MAGLDR will boot, choos 5 USB Flash and flash your favourite version of Clockworkmod (250 Mb version recommended)
Now you are ready to use MAGLDR and/or Clockworkmod any way you want.
If you skip/downgrade and of use DAF update after 5, your phone will be confused as hell. In that case do a TASK29 and start again from step 1.
Alternatively get a copy of HD2-Tool and do all above steps with that. Its really good.
Hello!!
I have a dft nand rom running on my htc but now i wanted to get my htc back to stock, with the Windows mobile 6.5.. I know how to do it, the problem is,, in order to install the dft nand android i had to install the radio, MAGLDR, and the HSPL, and now i need to sync my device to my computer to get it back to stock, I tried the htc sync but it didn't work and by turning on my htc pressing the down volume and the power button it should go to the HSPL but it won't, it has disappeared from my device...
And to install the HSPL again i need to sync my htc to my computer, but i can't..
I would appreciate any kind of help.
Thanks
No syncing is required as far as I know. Boot into the bootloader (vol down+power) then flash the RUU (make sure you hold down both buttons until the bootloader appears). Since you say you can't do that (although you may have just been letting go of the buttons too early) just flash a newer Android ROM. The DFT one is extremely old and was really more of a proof of concept ROM than one which people regularly use.
Can you post a link of a more recent rom?
thanks
I am not using a DFT rom.. i was turning on my htc and i saw that i'm using a Desire_DL from DL Super Init
vol down+power is to go to the HSPL and that i can't do because my HSPL, i don't know why but, it's not there anymore.
Then you have the flash bootloader just by holding the power button..
And i have to install the stock rom with the active sync so i can erase all the MAGLDR and stuff and have my htc as i bought it..
I am having to much trouble with this android thing on my HD2
samnie25 said:
Can you post a link of a more recent rom?
thanks
Click to expand...
Click to collapse
Find one yourself, stop being so lazy.
samnie25 said:
I am not using a DFT rom.. i was turning on my htc and i saw that i'm using a Desire_DL from DL Super Init
Click to expand...
Click to collapse
That doesn't change the fact that it's an old ROM, flash a newer one.
samnie25 said:
vol down+power is to go to the HSPL and that i can't do because my HSPL, i don't know why but, it's not there anymore.
Then you have the flash bootloader just by holding the power button..
And i have to install the stock rom with the active sync so i can erase all the MAGLDR and stuff and have my htc as i bought it..
I am having to much trouble with this android thing on my HD2
Click to expand...
Click to collapse
Lol you need to read the guide in my sig which talks about the terms used for the HD2, volume down + power is to enter the bootloader, you can't 'enter HSPL', it's just something you have to flash.
First of all, i'm not being lazy, you said to install a recent rom, i'm sorry i don't know which are the new ones and the old ones...
Second,.. when you press volume down + power you will get to the HSPL which is an image splited in 4 parts, red, green, blue and white..
That screen its what you get by installing the HSPL and that is the thing missing in my htc, that it use to have but somehow it disappeared and i can't install it again because i can't sync my phone with the computer
The bootloader, you just hold the power button to enter it..
its the MAGLDR
At least in my phone when i hold just the power button it says there "Boot menu", among other things, like boot ad sd, boot ad nand, usb flasher..
So many "boot" words, it must be the bootloader i guess..
The volume down + power is to automatically sync your phone with the computer
I refuse to help you any more. You ARE being lazy, each ROM has a date next to it. You don't know what you're talking about yet you refuse to listen to me (trust me, I know a lot more than you on this subject) and you're not even making any sort of effort. Good luck sorting things out, but I just cba with you any more.
samnie25 said:
First of all, i'm not being lazy, you said to install a recent rom, i'm sorry i don't know which are the new ones and the old ones...
Second,..when you press volume down + power you will get to the HSPL which is an image splited in 4 parts, red, green, blue and white..
That screen its what you get by installing the HSPL and that is the thing missing in my htc , that it use to have but somehow it disappeared and i can't install it again because i can't sync my phone with the computer
The bootloader, you just hold the power button to enter it..
its the MAGLDR
At least in my phone when i hold just the power button it says there "Boot menu", among other things, like boot ad sd, boot ad nand, usb flasher..
So many "boot" words, it must be the bootloader i guess..
The volume down + power is to automatically sync your phone with the computer
Click to expand...
Click to collapse
As Nigel said, each ROM has a date which indicates the last time it was updated.
That is the bootloader screen, either SPL or HSPL. And it can't be "missing". Because if you don't have that, your device wouldn't even boot. You just didn't-know-how-to/couldn't get to it, but it's there.
Again, that screen can't disappear. You may be having issues with your volume rockers. As a matter of fact, your phone is bricked if you don't have that, as I stated earlier.
MAGLDR is indeed a bootloader, but it's not the device's main bootloader.
Wow, just wow. Not because there are many "boot"s, it's a bootloader. The main bootloader of the device is the H/SPL (volume down + end)
i.e. the main bootloader.
Click here for more information about HSPL and MAGLDR.
My volume rockers are working good.. First i thought they were not working well but i checked several times and they seem good.
When i press volume down + power it just goes to the MAGLDR and i know that it shouldn't go.. So i guess my HSPL disappeared somehow..
And i know that in order to install it again, the device must be sync with the computer, but i downloaded the htc sync and it doesn't recognize my phone.
Or as you said "that screen can't disappear" is there any other way to enter it?
... but ... seriously? After all what I had said, you still insist that you don't have HSPL and you need to install it?
Dude, without H/SPL, MAGLDR WILL NOT BOOT.
If you want to go to the bootloader, you must press and HOLD the volume down and boot WHILE STILL holding the volume down.
If you mean the bootloader then call it the bootloader, stop calling it 'the HSPL'. Try this solution from walts
walts said:
Hold Volume Down. Press and hold Reset until you see the BootLoader screen. Reset is the hidden button under the battery cover, lower left side below the SD card slot. You need a plastic or wooden stylus (toothpick will work). DON'T use a pencil, the graphite can get into the button and short it.
I just did it to be sure. It works.
HTH
Walt
Click to expand...
Click to collapse
hspl
Marvlesz said:
... but ... seriously? After all what I had said, you still insist that you don't have HSPL and you need to install it?
Dude, without H/SPL, MAGLDR WILL NOT BOOT.
If you want to go to the bootloader, you must press and HOLD the volume down and boot WHILE STILL holding the volume down.
Click to expand...
Click to collapse
I don't know if it is there or not.. i press volume down and power button and it just doesn't go to that colorful screen.. I've did it before, to get my htc back to stock with the windows mobile rom.
but now it doens't work,. it's like i am not pressing the volume down... if i hold volume down and hold power button it goes to the MAGLDR (Where we have a bunch of options) and if i hold volume down and just press power button (Without holding) it just loads the rom... it's like i am not pressing the volume down, but it is working, i can up and down the volume and i can go up and down through the option in the MAGLDR menu..
So, i don't know
But thanks
HTC
Nigeldg said:
If you mean the bootloader then call it the bootloader, stop calling it 'the HSPL'. Try this solution from walts
Click to expand...
Click to collapse
Just tried that, with the reset.. didn't work.
but thank.
I guess there must be some problem with the volume controller...
i will open the phone and try..
but thank you all for the time