Database Users

Can't flash WM6.5, stuck on WP7?

I've got WP7 on my HD2. I want to flash a custom WM6.5 again and then run Android
However I can't flash anything over WP7. CustomRUU says a Error 260 connection
When the phone is plugged in, Zune starts and can see the phone listed. However Windows Mobile Device Centre stays as not connected. I've tried a hard reset i've tried holding the VolDown and power button to no avail.
How can I revert back to WM6.5?

enter inot bootloader than flash

mwang said:
enter inot bootloader than flash
Click to expand...
Click to collapse
sorry to sound like a n00b(because i am one) but how do i get into the bootloader?

geon106 said:
sorry to sound like a n00b(because i am one) but how do i get into the bootloader?
Click to expand...
Click to collapse
turn your phone off then turn it back on while holding the volume down button and connect to your pc then flash your 6.5 rom

JJbdoggg said:
turn your phone off then turn it back on while holding the volume down button and connect to your pc then flash your 6.5 rom
Click to expand...
Click to collapse
i've tried it from that screen, but it still doesn't seem to work :/ I think it is something i'm doing wrong and not the phone or it'll be something simple i've overlooked

geon106 said:
i've tried it from that screen, but it still doesn't seem to work :/ I think it is something i'm doing wrong and not the phone or it'll be something simple i've overlooked
Click to expand...
Click to collapse
You can also rename RUU_signed.nbh into leoimg.nbh and copy leoimg.nbh to your sd-card by using a card-reader, then get your screen in bootloader-mode and follow the instructions on your screen, when the update is completed, give a softreset, that should do the trick.
Regards,

Hi, I have the same problem. when try to flashback my 6.5 Room, on the 3 color screen, After After 5 minutes ... ERROR No Conection. I have HSPL version : SPL-2.08.000.

flashing back to windows phone 6.5
ensure the phone is charged more than 50%
switch the phone off
(at the same time) press the end key (hang up) and the volume down button. this will get you into the tri colour screen.
at the bottom of this screen should be written serial, at this point plug the phone into the pc, the "serial" should change to usb.
on the pc you should hear the usb plugged in confimation sound and the safely remove usb should show a device called "Qualcomm CDMA technologies MSM"
at this point start Custom RUU and proceed to flash the device as normal.
tried to make it as simple as possible
hope this helps.
edit: the tri colour screen everyone keeps talking about is the bootloader

emgp said:
Hi, I have the same problem. when try to flashback my 6.5 Room, on the 3 color screen, After After 5 minutes ... ERROR No Conection. I have HSPL version : SPL-2.08.000.
Click to expand...
Click to collapse
you need HPSL, and no you don't have it cause it would say HSPL 2.xx.xxx

Thank you for your fast response,
I'm doing all the procedure exactly, but when I proceed to flash to W6.5 The progress bar stays at 0% for 3 minutes , and on my pc appears the message "of connection error". If i reset the Hd2, it boot again in WP7. Any suggestions?, I have an HD2 Leo (512) and my HSPL is 2.08.00000. Thanks in advance.

My fault, its true. In the multicolor screen appears SPL-2.08.0000 .. Now, how can i reinstall the HSPL ? ,if I have installed WP7?.

Exit the Zune program and reflash the Original stock HD2 rom, not the updated 3.14 roms.
Russ

emgp said:
Thank you for your fast response,
I'm doing all the procedure exactly, but when I proceed to flash to W6.5 The progress bar stays at 0% for 3 minutes , and on my pc appears the message "of connection error". If i reset the Hd2, it boot again in WP7. Any suggestions?, I have an HD2 Leo (512) and my HSPL is 2.08.00000. Thanks in advance.
Click to expand...
Click to collapse
well make sure you have HPSL, then from there power off your phone, but turn it back on by holding down the Vol down button and the power button, and keep holding it till you get to the tri color screen, connect your phone and it should say USB on the bottom of your phone, then from there flash like the regular way.

Help, I have bricked my HTC HD2 using MAGLDR 1.11

Hello all,
I was trying to get android booting from NAND instead of the SD card, I got a rom with 576ram (recommended) and installed MAGLDR 1.11. Now i cant seem to do anything with the phone, its not bricked as par say, it will show the loading screen and then not move and i can access the bootloader with voldwn+powerbutton but nothing else is happening, I cant load new roms nothing. Im pretty lost here and really need some help of how i can get my phone back onto a winmo6.5 rom so i can remember not to try it again
I posted this in this thread as it does relate to an android situation.

norodaigh said:
Hello all,
I was trying to get android booting from NAND instead of the SD card, I got a rom with 576ram (recommended) and installed MAGLDR 1.11. Now i cant seem to do anything with the phone, its not bricked as par say, it will show the loading screen and then not move and i can access the bootloader with voldwn+powerbutton but nothing else is happening, I cant load new roms nothing. Im pretty lost here and really need some help of how i can get my phone back onto a winmo6.5 rom so i can remember not to try it again
I posted this in this thread as it does relate to an android situation.
Click to expand...
Click to collapse
Find Task29.exe with no radio. It's on this site somewhere. You will see some with radios attached to them, so don't use those. Just the plain old no radio version. It will wipe your phones internal memory and you will basically be starting from scratch. Nothing will be on your phone after a Task29. Then go into bootloader. How to enter boot loader after Task29- Once Task29 hits 96% (looks just like you are flashing a rom), hold volume down and power from 96% until it gets to 100% and the tri color bootloader screen pops up. It should say "USB" at the bottom after bootloader comes up if you are plugged into your computer. Then Flash MAGLDR 1.11 again. Then flash your NAND build.
You aren't bricked if you phone powers on.
What operating system is on your PC?

Well it does boot and if you have hspl you did a good job. So if you have magdlr you now need to install Android. Read a guide plzzz!
Sent from my HTC HD2 using XDA App

OS on PC is....#sigh# windows vista ultimate
For task 29 do I have to have the phone connected via usb, because its not recognising it when its even in bootloader

task29.exe didnt work

Don't do task 29,you will just complicate your life even more than now. I don't think you know what you are doing.
You may brick your phone in the end do you have HSPL?
Sent from my HTC HD2 using XDA App

crisisinthecity said:
Find Task29.exe with no radio. It's on this site somewhere. You will see some with radios attached to them, so don't use those. Just the plain old no radio version. It will wipe your phones internal memory and you will basically be starting from scratch. Nothing will be on your phone after a Task29. Then go into bootloader. How to enter boot loader after Task29- Once Task29 hits 96% (looks just like you are flashing a rom), hold volume down and power from 96% until it gets to 100% and the tri color bootloader screen pops up. It should say "USB" at the bottom after bootloader comes up if you are plugged into your computer. Then Flash MAGLDR 1.11 again. Then flash your NAND build.
You aren't bricked if you phone powers on.
What operating system is on your PC?
Click to expand...
Click to collapse
1st try entering the BOOTLOADER, by pressing the volume down power button simultaneously..!!!
Instead of TASK 29, try FLASHAHOLIC which will perform your TASK 29 & help you flash a WinMO 6.5 ROM as well..!!!
PS: - You can even flash custom ROM's, stock ROM's not compulsory..!!!

norodaigh said:
OS on PC is....#sigh# windows vista ultimate
For task 29 do I have to have the phone connected via usb, because its not recognising it when its even in bootloader
Click to expand...
Click to collapse
Well then re-install Active SYNC or try on a diff PC with Latest Active SYNC..!!!
If you can access your boot-loader your device ain't bricked..!!!

Just boot your phone with VolDown and enter USB mode, reflash MAGLDR 1.11, once this has completed reboot your phone and hold down the power button, you will then see the MAGLDR menu.
Then just follow instructions on how to install an nand rom
http://forum.xda-developers.com/showthread.php?t=893948

it might just be the magldr or NAND ROM not flashed properly. If you can get to Tri-Color bootloader you are fine.

Found out the problem, thanks for all of your help guys, it was the fact i didnt have hspl2 installed....newb points to me

I have exactly the same problem only difference with my problem is when hold vol down and power buttons all I get is the tri coloured screen and nothing else no bootloader menu appears at all.
What can I do? Is my phn dead???

barryhd2 said:
I have exactly the same problem only difference with my problem is when hold vol down and power buttons all I get is the tri coloured screen and nothing else no bootloader menu appears at all.
What can I do? Is my phn dead???
Click to expand...
Click to collapse
That's exactly what is supposed to happen if you hold the vol down button while switching on. To get to the magldr menu you need to hold the power button in until it boots to the menu (no vol down button )

You guys are awesome!
I've been avoiding dealing with this phone for a while. This post came up first on google search. Held power and volume (mag 1.11 was on it) and upgraded it to 1.13 and now I'm golden! Thanks guys!!!!!!!!!!!!!

[Q] Cannot start bootloader, HD2 stuck on HTC logo screen

WM6.5 on my HD2 (from T-Mobile europe) has finally bothered me enough to decide to change the rom entirely, to android (NAND). I saw the instructions/video tutorial by techburrow (including the magldr v 1.11) and thought that it wouldn't give me too much troubles.
Before starting, I checked my ROM to see if it was recent enough. I as well installed hspl v 2.08 (as shown after taking battery out/in and using volume down + startbutton, in the rgbw screen).
After that I (think I) successfully installed MAGLDR v 1.11. It showed the comment that my phone was now "hacked".
I then went on to the most important step in the process, actually loading android. In the instructions for DFT_Android is states that:
" For installation you need enter MAGLDR (hold power button during boot)"
I tried getting into bootloader by holding the power button, I tried pressing it once and then holding it. Neither worked, both ended up with the HTC logo screen.
All I can do now is choose between getting the HTC logo and the rgbw screen showing hspl 2.08.
Hard reset also doesn't work, probably because MAGLDR deleted the original rom. Connecting through USB via the rgbw screen doesnt work, the connection is not recognised.
Other thread look similar problem, but haven't helped so far. Only the most recent are about others trying to get the android on NAND with MAGLDR 1.11 and DFT-Android.
HELP? Anybody has any idea on how I can install android any ROM now, how to get into the bootloader, how to use my HD2 again?

Looks like Magldr was not flash into the phone. Reflash magldr.
Sent from my HTC HD2 using XDA App

unfortunately
Thx for the suggestion, xhanay. However, reflashing MAGLDR requires an activesync connection and/or USB connection via HSPL (only way my phone does anything). Cannot get any connection unfortunately. So no reflashing.
Any other suggestions? (reflashing via microSD?)

help!i have the really same problem!thx!

This is what I do:
1. Remove the battery, put it back
2. Hold VolDown key pressed while turn on the phone to enter Bootloader (tricolored screen)
3. Connect it to PC and wait for connection to change to USB
4. Flash radio 2.15.50.14
5. Hold VolDown key pressed after reboot to enter bootloader again.
6. Flash MAGLDR
7. Reboot
8. Hold Power button pressed > Select USB flasher ...
....and flash Android/Windows 7.
If USB connection is not recognized I suggest flashing a stock ROM using SD card.
See instructions here, chapter 3 - Flashing Via MicroSD Card

could just work
Thank you for the quick response. Hopefully I will make it all the way to step 8+ (with android and all apps coming along with it). Otherwise using the stock rom should help. Thx for the link.
Will let you know if it works.

Also post in the right section in the future

All worked. I had to reflash a custom ROM through the rgbw screen (apparently a custom ROM did synchronise via USB even though activesync didnt show anything). Then I reinstalled MAGLDR (which immediately sent me through to the bootlader screen). After I had some issues loading android (had to tag USB on in Activesync connection settings, make the connection, the tag USB off in the connection settings)... Now Android is running as I hoped it would. Great work and thanx to all that helped.
ps: Will try to use the right section next time. No promises that it will then be the right one however.

I have the same problem and tried this only to be sent back into magdlr where it just scrolls up and down with the volume key held down.
Any suggestions much appreciated.

dixieuk101 said:
I have the same problem and tried this only to be sent back into magdlr where it just scrolls up and down with the volume key held down.
Any suggestions much appreciated.
Click to expand...
Click to collapse
you could try .... than just plug-it in using activesync and run HSPL3... do not install it...before installing it will put ur phone in bootloader....than exit HSPL3 keep your phone pluged in and just flash wtever....radio,rom...etc....
OR
Press together VOLUME DOWN - DO NOT LET GO! EVER TILL IN BOOTLOADER & RESET RED BUTTON - under batt. metal cover -
after few seconds the tri-coloured screen will appear

load the hard SPL than magledr than rom it works 100%

Same Problem!!!
Hey i have the same problem. Recently I bought this phone off of craigslist. The phone goes to the DFT screen and its on aMAGDLR v1.11. I tried to reset it but it doesnt go to the multi colored screen. I bought a new micro sd but that didnt work. It also cant connect to my computer. There isnt wrong with the charging port because the light goes on when its connected. PLEASE HELP?! I cant go into bloatloader. Is it bricked?

Hi,
I had used HD2ToolKit4.2.0.1.zip and use Wipe option given in the bottom left.
Regards

my volume key not work and now i cant use the bootloader,please

hey anybody here??????????????

now what is soluton for this bootloader nogo
stucked between magldr and dft screen
pls help

now what is soluton for this bootloader nogo
stucked between magldr and dft screen
pls help
Click to expand...
Click to collapse
did you do this with right order?
http://forum.xda-developers.com/showpost.php?p=27057672&postcount=127

Potentially Unrecoverably HD2 Stuck In MAGLDR

Hi All,
For the past few months I've been running a DFT NAND build of Android. Yesterday, the phone was running extremely slowly with some odd behavior in the Android menus. When I restarted the phone, loading got as far as the DFT splash screen but then nothing else would happen.
I have since used MAGLDR (1.11) to attempt to boot a fresh Android image from SD card but this hasn't worked. Have managed to use the USB Loader to attempt to flash another NAND build (both Android and WP7) but even though the download process completed, this still didn't work and am stuck in MAGLDR now.
Have read through the forums here and have tried most (if not all) of the suggestions, however nothing seems to be working.
Can anyone offer anymore advice?
Thanks,
Kev

As MAGLDR gets removed if you flash a stock winmo rom I suggest you to try that!
Before you install the winmo rom you can also use Task29 to completely wipe the nand.
good luck

Thanks,
I shall give that a try this evening.
Kev

Unfortunately none of the suggestions have worked. I'm unable to flash a stock WM6.5 ROM as the RUU doesn't detect the phone.
The device does show up in Windows as a Microsoft USB Sync device, however.
Task 29 does not work either due to the same problem.
I've attempted to flash a new Android ROM release but when the phone reboots, it gets stuck on the green HTC logo screen and won't proceed any further.
I don't seem to be able to get MAGLDR 1.13 on the phone either, as DAF.exe complains about some "Config load failed" error.
Any other suggestions?
Thanks in advance,
Kev

*sigh*
you need to read up on "how to flash stock rom from sd card". no need for RUU i believe; sd card method involves copying a file extracted from the stock RUU and placing it in the root of your sd card and letting bootloader detect and flash the file. search for a tutorial or see the stickies.
once you've done that, make a special note about the part that says you need to boot into bootloader (hold down volume down + turn on phone + keep holding volume down until a 4-color screen appears). i suspect you are not doing this step, this is why windows, mtty, etc are unable to detect the device.
if you have already done the above, ignore my post

*sigh* too.
I've already tried flashing from the SD card but I have the same problem. I get to a green HTC loading screen and nothing else happens. I just get stuck in a reboot to MAGLDR and try again loop.
I've read through plenty of posts on flashing custom ROM's and troubleshooting but nothing has helped.
I don't get a 4 colour screen when holding down VOL-DOWN and the power button, the phone just goes into MAGLDR.
Kev

Just to add to that, Windows DOES detect the device but the RUU doesn't. Only the DAF applications find and can talk to the device.

follow me
1. is the battery have enough jiuce? what HSPL you use? hope its HSPL3 2.08HSPL
2. bootloader . . . .

Thanks for your post.
Plenty of juice in the battery.
I believe it is HSPL 2.08 (well, whichever allowed me to get Android on the thing in the first place)
Bootloader what?
Kev

getting into boot loader (4-color screen) is the key to the whole flash with sd card method.
keep trying. read on how to enter bootloader.
i can remember a few ways.
DEVICE IS ON
1. if phone is already on, hold down volume down (keep it pressed HARD)...don't let go of it!
2. push the little reset button under the battery cover. don't let go of the volume down button!
3. don't let go of the volume down button until the 4-color screen appears.
DEVICE IS OFF
1. remove the battery. reinsert it after a few seconds.
2. hold down volume down (keep it pressed HARD)...don't let go of it!
3. tap the end call button and don't let go of the volume down button until the 4-color screen appears.
remember, entering bootloader is the key.
EDIT: it is better to ensure you have sufficient battery. however, flashing via bootloader SKIPS the battery level checks.

kevinwebster83 said:
Thanks for your post.
Plenty of juice in the battery.
I believe it is HSPL 2.08 (well, whichever allowed me to get Android on the thing in the first place)
Bootloader what?
Kev
Click to expand...
Click to collapse
in post 4 you noted you tried task 29 but was successful
you are not even familiar with bootloader, ??? makes me wonder

I'm very familiar with a bootloader, your "bootloader..." comment confused me.
Task 29 was unsuccessful. I've read in a number of posts that you can use Task 29 and start from scratch back at the original bootloader (rather than MAGLDR) but this obviously isn't the case.
Holding down the VOL-DOWN key does nothing other than get me to MAGLDR, which is what happens even if I don't hold any keys down.
I fully understand that the key is entering the bootloader, nothing seems to let me get there.
Kev

kevinwebster83 said:
I'm very familiar with a bootloader, your "bootloader..." comment confused me.
Task 29 was unsuccessful. I've read in a number of posts that you can use Task 29 and start from scratch back at the original bootloader (rather than MAGLDR) but this obviously isn't the case.
Holding down the VOL-DOWN key does nothing other than get me to MAGLDR, which is what happens even if I don't hold any keys down.
I fully understand that the key is entering the bootloader, nothing seems to let me get there.
Kev
Click to expand...
Click to collapse
this is how i enter bootloader from magldr
remove battery
reinsert, leave device off
hold and continue to hold volume down
briefly press power/call button
now your in bootloader
this will show your hspl

Battery removed
VOL-DOWN held
Powered on
VOL-DOWN still held
MAGLDR appears
This isn't my bootloader and doesn't show HSPL

kevinwebster83 said:
Battery removed
VOL-DOWN held
Powered on
VOL-DOWN still held
MAGLDR appears
This isn't my bootloader and doesn't show HSPL
Click to expand...
Click to collapse
if you are now unable to enter bootloader
in this manner, there is only one thing i can think of
you got a bricked device,
you might get some help if you post your querry in the
HSPL thread, or PM cotulla and team

I'm of the same opinion; it is virtually bricked.
The stupid thing is that if I select Android Flasher from MAGLDR, I'm able to flash a different version of Android to NAND but it just won't boot.
Will try a different forum.
Thanks,
Kev

kevinwebster83 said:
I'm of the same opinion; it is virtually bricked.
The stupid thing is that if I select Android Flasher from MAGLDR, I'm able to flash a different version of Android to NAND but it just won't boot.
Will try a different forum.
Thanks,
Kev
Click to expand...
Click to collapse
i discourage you to try another forum
if you got hold of HSPL, task 29 and other stuff here in xda
then this is the best place you can be helped
try to post in HSPL thread
or PM ClydeB1, or bepe.
if they cant help you
then i highly doubt if anyone in this world will

Which HSPL thread would you recommend?

kevinwebster83 said:
Which HSPL thread would you recommend?
Click to expand...
Click to collapse
the original by bepe, cotulla and DFT

I have the same problem...does the HD2 charge itnself in Magldr ?

[Q] Please help - going back to stock ROM

Hi All,
I have been running a few NAND Android ROMS but seem to have an issue where pushing the power button on the HD2 no longer locks the phone, it just brings up the Power Off / Airplane mode options etc.
I think the button is damaged and sticking so wanted to go back to stock WinMo ROM to test this and if necisary send back for repair.
I have downloaded the stock O2 ROM from HTC.com but cant work out how to load this ROM. I presume I need to boot to HSPL?? only thing is I cant boot to it, I just get the MAGLDR screen.
Not sure if I'm doing something blatantly stupid or even if the button is not actually broken, although it does exactly the same in all Android builds I have tried. Is there a softkey that can be set to lock the screen?
Any adive much appreciated.
Thanks
Denno

Phone off
hold vol down
tap and release power
keep holding vol down till coloured screen apears
plug in usb, wait for serial to chnge to usb, run the flash.
If you have the 3.14 stock you also need to run hspl4 and choose 3.03.0000
Or
flash from sd card (look it up) will do both the flash and set 3.03.0000 all in one go.