[Q] Please help - going back to stock ROM - HD2 General

Hi All,
I have been running a few NAND Android ROMS but seem to have an issue where pushing the power button on the HD2 no longer locks the phone, it just brings up the Power Off / Airplane mode options etc.
I think the button is damaged and sticking so wanted to go back to stock WinMo ROM to test this and if necisary send back for repair.
I have downloaded the stock O2 ROM from HTC.com but cant work out how to load this ROM. I presume I need to boot to HSPL?? only thing is I cant boot to it, I just get the MAGLDR screen.
Not sure if I'm doing something blatantly stupid or even if the button is not actually broken, although it does exactly the same in all Android builds I have tried. Is there a softkey that can be set to lock the screen?
Any adive much appreciated.
Thanks
Denno

Phone off
hold vol down
tap and release power
keep holding vol down till coloured screen apears
plug in usb, wait for serial to chnge to usb, run the flash.
If you have the 3.14 stock you also need to run hspl4 and choose 3.03.0000
Or
flash from sd card (look it up) will do both the flash and set 3.03.0000 all in one go.

Related

Help, I have bricked my HTC HD2 using MAGLDR 1.11

Hello all,
I was trying to get android booting from NAND instead of the SD card, I got a rom with 576ram (recommended) and installed MAGLDR 1.11. Now i cant seem to do anything with the phone, its not bricked as par say, it will show the loading screen and then not move and i can access the bootloader with voldwn+powerbutton but nothing else is happening, I cant load new roms nothing. Im pretty lost here and really need some help of how i can get my phone back onto a winmo6.5 rom so i can remember not to try it again
I posted this in this thread as it does relate to an android situation.
norodaigh said:
Hello all,
I was trying to get android booting from NAND instead of the SD card, I got a rom with 576ram (recommended) and installed MAGLDR 1.11. Now i cant seem to do anything with the phone, its not bricked as par say, it will show the loading screen and then not move and i can access the bootloader with voldwn+powerbutton but nothing else is happening, I cant load new roms nothing. Im pretty lost here and really need some help of how i can get my phone back onto a winmo6.5 rom so i can remember not to try it again
I posted this in this thread as it does relate to an android situation.
Click to expand...
Click to collapse
Find Task29.exe with no radio. It's on this site somewhere. You will see some with radios attached to them, so don't use those. Just the plain old no radio version. It will wipe your phones internal memory and you will basically be starting from scratch. Nothing will be on your phone after a Task29. Then go into bootloader. How to enter boot loader after Task29- Once Task29 hits 96% (looks just like you are flashing a rom), hold volume down and power from 96% until it gets to 100% and the tri color bootloader screen pops up. It should say "USB" at the bottom after bootloader comes up if you are plugged into your computer. Then Flash MAGLDR 1.11 again. Then flash your NAND build.
You aren't bricked if you phone powers on.
What operating system is on your PC?
Well it does boot and if you have hspl you did a good job. So if you have magdlr you now need to install Android. Read a guide plzzz!
Sent from my HTC HD2 using XDA App
OS on PC is....#sigh# windows vista ultimate
For task 29 do I have to have the phone connected via usb, because its not recognising it when its even in bootloader
task29.exe didnt work
Don't do task 29,you will just complicate your life even more than now. I don't think you know what you are doing.
You may brick your phone in the end do you have HSPL?
Sent from my HTC HD2 using XDA App
crisisinthecity said:
Find Task29.exe with no radio. It's on this site somewhere. You will see some with radios attached to them, so don't use those. Just the plain old no radio version. It will wipe your phones internal memory and you will basically be starting from scratch. Nothing will be on your phone after a Task29. Then go into bootloader. How to enter boot loader after Task29- Once Task29 hits 96% (looks just like you are flashing a rom), hold volume down and power from 96% until it gets to 100% and the tri color bootloader screen pops up. It should say "USB" at the bottom after bootloader comes up if you are plugged into your computer. Then Flash MAGLDR 1.11 again. Then flash your NAND build.
You aren't bricked if you phone powers on.
What operating system is on your PC?
Click to expand...
Click to collapse
1st try entering the BOOTLOADER, by pressing the volume down power button simultaneously..!!!
Instead of TASK 29, try FLASHAHOLIC which will perform your TASK 29 & help you flash a WinMO 6.5 ROM as well..!!!
PS: - You can even flash custom ROM's, stock ROM's not compulsory..!!!
norodaigh said:
OS on PC is....#sigh# windows vista ultimate
For task 29 do I have to have the phone connected via usb, because its not recognising it when its even in bootloader
Click to expand...
Click to collapse
Well then re-install Active SYNC or try on a diff PC with Latest Active SYNC..!!!
If you can access your boot-loader your device ain't bricked..!!!
Just boot your phone with VolDown and enter USB mode, reflash MAGLDR 1.11, once this has completed reboot your phone and hold down the power button, you will then see the MAGLDR menu.
Then just follow instructions on how to install an nand rom
http://forum.xda-developers.com/showthread.php?t=893948
it might just be the magldr or NAND ROM not flashed properly. If you can get to Tri-Color bootloader you are fine.
Found out the problem, thanks for all of your help guys, it was the fact i didnt have hspl2 installed....newb points to me
I have exactly the same problem only difference with my problem is when hold vol down and power buttons all I get is the tri coloured screen and nothing else no bootloader menu appears at all.
What can I do? Is my phn dead???
barryhd2 said:
I have exactly the same problem only difference with my problem is when hold vol down and power buttons all I get is the tri coloured screen and nothing else no bootloader menu appears at all.
What can I do? Is my phn dead???
Click to expand...
Click to collapse
That's exactly what is supposed to happen if you hold the vol down button while switching on. To get to the magldr menu you need to hold the power button in until it boots to the menu (no vol down button )
You guys are awesome!
I've been avoiding dealing with this phone for a while. This post came up first on google search. Held power and volume (mag 1.11 was on it) and upgraded it to 1.13 and now I'm golden! Thanks guys!!!!!!!!!!!!!

[Q] Cannot start bootloader, HD2 stuck on HTC logo screen

WM6.5 on my HD2 (from T-Mobile europe) has finally bothered me enough to decide to change the rom entirely, to android (NAND). I saw the instructions/video tutorial by techburrow (including the magldr v 1.11) and thought that it wouldn't give me too much troubles.
Before starting, I checked my ROM to see if it was recent enough. I as well installed hspl v 2.08 (as shown after taking battery out/in and using volume down + startbutton, in the rgbw screen).
After that I (think I) successfully installed MAGLDR v 1.11. It showed the comment that my phone was now "hacked".
I then went on to the most important step in the process, actually loading android. In the instructions for DFT_Android is states that:
" For installation you need enter MAGLDR (hold power button during boot)"
I tried getting into bootloader by holding the power button, I tried pressing it once and then holding it. Neither worked, both ended up with the HTC logo screen.
All I can do now is choose between getting the HTC logo and the rgbw screen showing hspl 2.08.
Hard reset also doesn't work, probably because MAGLDR deleted the original rom. Connecting through USB via the rgbw screen doesnt work, the connection is not recognised.
Other thread look similar problem, but haven't helped so far. Only the most recent are about others trying to get the android on NAND with MAGLDR 1.11 and DFT-Android.
HELP? Anybody has any idea on how I can install android any ROM now, how to get into the bootloader, how to use my HD2 again?
Looks like Magldr was not flash into the phone. Reflash magldr.
Sent from my HTC HD2 using XDA App
unfortunately
Thx for the suggestion, xhanay. However, reflashing MAGLDR requires an activesync connection and/or USB connection via HSPL (only way my phone does anything). Cannot get any connection unfortunately. So no reflashing.
Any other suggestions? (reflashing via microSD?)
help!i have the really same problem!thx!
This is what I do:
1. Remove the battery, put it back
2. Hold VolDown key pressed while turn on the phone to enter Bootloader (tricolored screen)
3. Connect it to PC and wait for connection to change to USB
4. Flash radio 2.15.50.14
5. Hold VolDown key pressed after reboot to enter bootloader again.
6. Flash MAGLDR
7. Reboot
8. Hold Power button pressed > Select USB flasher ...
....and flash Android/Windows 7.
If USB connection is not recognized I suggest flashing a stock ROM using SD card.
See instructions here, chapter 3 - Flashing Via MicroSD Card
could just work
Thank you for the quick response. Hopefully I will make it all the way to step 8+ (with android and all apps coming along with it). Otherwise using the stock rom should help. Thx for the link.
Will let you know if it works.
Also post in the right section in the future
All worked. I had to reflash a custom ROM through the rgbw screen (apparently a custom ROM did synchronise via USB even though activesync didnt show anything). Then I reinstalled MAGLDR (which immediately sent me through to the bootlader screen). After I had some issues loading android (had to tag USB on in Activesync connection settings, make the connection, the tag USB off in the connection settings)... Now Android is running as I hoped it would. Great work and thanx to all that helped.
ps: Will try to use the right section next time. No promises that it will then be the right one however.
I have the same problem and tried this only to be sent back into magdlr where it just scrolls up and down with the volume key held down.
Any suggestions much appreciated.
dixieuk101 said:
I have the same problem and tried this only to be sent back into magdlr where it just scrolls up and down with the volume key held down.
Any suggestions much appreciated.
Click to expand...
Click to collapse
you could try .... than just plug-it in using activesync and run HSPL3... do not install it...before installing it will put ur phone in bootloader....than exit HSPL3 keep your phone pluged in and just flash wtever....radio,rom...etc....
OR
Press together VOLUME DOWN - DO NOT LET GO! EVER TILL IN BOOTLOADER & RESET RED BUTTON - under batt. metal cover -
after few seconds the tri-coloured screen will appear
load the hard SPL than magledr than rom it works 100%
Same Problem!!!
Hey i have the same problem. Recently I bought this phone off of craigslist. The phone goes to the DFT screen and its on aMAGDLR v1.11. I tried to reset it but it doesnt go to the multi colored screen. I bought a new micro sd but that didnt work. It also cant connect to my computer. There isnt wrong with the charging port because the light goes on when its connected. PLEASE HELP?! I cant go into bloatloader. Is it bricked?
Hi,
I had used HD2ToolKit4.2.0.1.zip and use Wipe option given in the bottom left.
Regards
my volume key not work and now i cant use the bootloader,please
hey anybody here??????????????
now what is soluton for this bootloader nogo
stucked between magldr and dft screen
pls help
now what is soluton for this bootloader nogo
stucked between magldr and dft screen
pls help
Click to expand...
Click to collapse
did you do this with right order?
http://forum.xda-developers.com/showpost.php?p=27057672&postcount=127

pls help...downgrade my htc hd2 android to wm6.5

hi guys i flashed my htc hd2 wm6.5 to nand android rom in 1st 1 week of usage i have no problem and enjoyed the nand android rom in my htc hd2 until one day my hd2 hang and when i reboot my unit it was hang on splash screen only....
i reflashed it using magdlr ver. 1.11 into the same nand rom im using but i have no luck...it still stock on tje android splash screen...what will i do guys?
im planning to flash it to wm6.5 rom,but what will i do?it never boot on tri color screen it only boot on magdlr screen
and how can i flash it wm6.5 rom cook or stock rom i want to revert it back to wm6.5
my hd2 running on gingerbread 2.3.3 nand(V1.8) rom before it malfunction..
Well, my forensic analysis has come up with the following technical and somewhat difficult solution to your present problem: "Click the search button"
Now I know it may sound intimidating, but I tested that feature out for you and came up with this:
http://forum.xda-developers.com/showthread.php?t=905841
matt
Shut down completely your phone (remove batter for 15 sec too)
Place battery back and now hold volume down button.
Still hold volume down button and switch on your phone.
You get 3 color screen.
Now attach your usb cable and connect it to PC
Find on this forum your phone stock win mobile rom (link to officila roms thread)
Run stock win 6.5 rom exe (this is sample name: RUU_Leo_S_HTC_WWE_EastEurope_3.14.479.2_Radio_15.42.50.11U_2.15.50.14_LEO_S_Ship.exe)
Follow instructions on your PC screen. On final your phone reboots.
Enjoy your stock phone.
hi datasoft thanks for the quick reply...
i try your suggestion to enter into bootloader mode but it booted on the magldr screen...
can i flash wm6.5 rom into magdlr usb flasher?
siapelbo said:
hi dasoft thanks for the quick reply...
i try your suggestion to enter into bootloader mode but it booted on the magldr screen...
Click to expand...
Click to collapse
Switch off, hold vol down button in and switch on.
As ClydeB1, states you must hold the vol down only and not hold the power button.
siapelbo said:
hi dasoft thanks for the quick reply...
i try your suggestion to enter into bootloader mode but it booted on the magldr screen...
Click to expand...
Click to collapse
when you get ready to power back on you have to hold volume down and keep holding it while is booting and it should switched to the tricolored screen, plug the usb cable and it should say usb at the bottom when it connects, and if you have hardspl which I know you have after running android, you can use any custom winmo6.5 rom it doesn't have to be an official rom.
can i flash wm6.5 rom into magdlr usb flasher?
No, flash from bootloader.
awts...i cant enter into booloader mode....im so sure what im doing i sure i follow the instructions of you guys....holding down the vol button and switch on
Are you holding it at the bottom of the button and not in the middle or top, ie as if you are turning the volume down?
I don't think you can flash WM6.5 with flasher. You have to restore from recovery screen by remove battery and restore.
ClydeB1 said:
Are you holding it at the bottom of the button and not in the middle or top, ie as if you are turning the volume down?
Click to expand...
Click to collapse
yeah im sure i was holding down the volume botton and switch the power on
Does the vol down button work normally in the Android rom or when moving around in magldr. To be sure, remove the battery and leave it out for 10 minutes then put the battery back, leave the cover off and try again.
I have heard of one or two users who have also had a problem where the vol down button stopped working. If that is the case there is no way back AFAIK.
ClydeB1 said:
Does the vol down button work normally in the Android rom or when moving around in magldr. To be sure, remove the battery and leave it out for 10 minutes then put the battery back, leave the cover off and try again.
I have heard of one or two users who have also had a problem where the vol down button stopped working. If that is the case there is no way back AFAIK.
Click to expand...
Click to collapse
volume botton is perfectly working it work around in magdlr mode actually i flashed my hd2 into android rom right now flashing is done without problems, but its not boot normarly it boot only in splash screen....
can you guys post a link of task 29...i will try this method and flash stock rom
but the main problem is i cant enter into bootloader mode
I use this tool for Task29 - http://forum.xda-developers.com/showthread.php?t=917807
Once you run Task29 though it will wipe the NAND memory and magldr and if you can't get back to bootloader mode then you will be stuck on the splashscreen.
Hi,
I'm also having problems, but in my case the progress bar on my phone when installing the new ROM stops at 0% and will stay there indefinably. On my computer a connection problem will be raised.
The same happens with task29.
I've also tried decompressing ROM Utility, putted leoimg.nbh on my 2GB fat32 formatted sdcard, hold down the volume key.
I will get a new screen with "Loading..." on it, but it freezes there.
So, I have no idea what I'm doing wrong.
Any help will be appreciated.
Regards,
temporary_24 said:
Hi,
I'm also having problems, but in my case the progress bar on my phone when installing the new ROM stops at 0% and will stay there indefinably. On my computer a connection problem will be raised.
The same happens with task29.
I've also tried decompressing ROM Utility, putted leoimg.nbh on my 2GB fat32 formatted sdcard, hold down the volume key.
I will get a new screen with "Loading..." on it, but it freezes there.
So, I have no idea what I'm doing wrong.
Any help will be appreciated.
Regards,
Click to expand...
Click to collapse
Are you sure you still have hspl installed? In bootloader, check your spl version- it should end in hspl.
ClydeB1 said:
Are you sure you still have hspl installed? In bootloader, check your spl version- it should end in hspl.
Click to expand...
Click to collapse
Hi,
Yes. I had one with a 8 on it. I've installed the other, and it worked (or the other way). Thanks.
Regards,
guys my phone revive with a jtag procedure i went to a technician shop here in the phillipines
my phone running in stock rom again...

Frozen Screen after flashing MAGLDR113 what can i do?

After flashing MAGLDR113 to install an NAND build my htc get freezed in the startingscreen. I can´t get into the bootloader and i also can´t do an hardreset.
What else can i do to get my hd2 working? I hope you can help me.
maybe usefull:
radio rom 2.15.50.14
Goatrip stock rom
greets schueffi
phone completely off
press power to turn on, but keep it pressed, dont let go.
phone will vibrate as it starts, then you see the first boot screen, (keeping power pressed still) then the screen jumps black with yellow at teh top, keep pressing power until teh menu items apear.
thanks but i´ve tryed that for many times but nothing happend...
is it possible to flash an rom without getting into the bootloader?
have anyone an other idea what i can do?
Not sure if this will help you, but I was being a noob and trying to use the touchscreen with magldr to select a menu item, but you're meant to use the volume up and down keys and the call button to select an item. To flash, select usb flasher. Hopefully that was of help
Hi, is there a solution for this? I have the same problem.
I wanted to install NAND Android on my HTC HD2 device actually running WM and Android on an SD card. I followed all the steps carefully:
I flashed HARDSPL with HSPL4
I updated the Radio version to 2.15.50.14
I installed MAGLDR113 and the installation gave me no problems, but when rebooting, the phone gets stuck in the initial screen and it doesn't either boot or let me go to the boot menu no matter for how long I press the power or the down volume button.
Anybody can help?
Thanks

[Q] HTC HD2 nand android problems

Hello!!
I have a dft nand rom running on my htc but now i wanted to get my htc back to stock, with the Windows mobile 6.5.. I know how to do it, the problem is,, in order to install the dft nand android i had to install the radio, MAGLDR, and the HSPL, and now i need to sync my device to my computer to get it back to stock, I tried the htc sync but it didn't work and by turning on my htc pressing the down volume and the power button it should go to the HSPL but it won't, it has disappeared from my device...
And to install the HSPL again i need to sync my htc to my computer, but i can't..
I would appreciate any kind of help.
Thanks
No syncing is required as far as I know. Boot into the bootloader (vol down+power) then flash the RUU (make sure you hold down both buttons until the bootloader appears). Since you say you can't do that (although you may have just been letting go of the buttons too early) just flash a newer Android ROM. The DFT one is extremely old and was really more of a proof of concept ROM than one which people regularly use.
Can you post a link of a more recent rom?
thanks
I am not using a DFT rom.. i was turning on my htc and i saw that i'm using a Desire_DL from DL Super Init
vol down+power is to go to the HSPL and that i can't do because my HSPL, i don't know why but, it's not there anymore.
Then you have the flash bootloader just by holding the power button..
And i have to install the stock rom with the active sync so i can erase all the MAGLDR and stuff and have my htc as i bought it..
I am having to much trouble with this android thing on my HD2
samnie25 said:
Can you post a link of a more recent rom?
thanks
Click to expand...
Click to collapse
Find one yourself, stop being so lazy.
samnie25 said:
I am not using a DFT rom.. i was turning on my htc and i saw that i'm using a Desire_DL from DL Super Init
Click to expand...
Click to collapse
That doesn't change the fact that it's an old ROM, flash a newer one.
samnie25 said:
vol down+power is to go to the HSPL and that i can't do because my HSPL, i don't know why but, it's not there anymore.
Then you have the flash bootloader just by holding the power button..
And i have to install the stock rom with the active sync so i can erase all the MAGLDR and stuff and have my htc as i bought it..
I am having to much trouble with this android thing on my HD2
Click to expand...
Click to collapse
Lol you need to read the guide in my sig which talks about the terms used for the HD2, volume down + power is to enter the bootloader, you can't 'enter HSPL', it's just something you have to flash.
First of all, i'm not being lazy, you said to install a recent rom, i'm sorry i don't know which are the new ones and the old ones...
Second,.. when you press volume down + power you will get to the HSPL which is an image splited in 4 parts, red, green, blue and white..
That screen its what you get by installing the HSPL and that is the thing missing in my htc, that it use to have but somehow it disappeared and i can't install it again because i can't sync my phone with the computer
The bootloader, you just hold the power button to enter it..
its the MAGLDR
At least in my phone when i hold just the power button it says there "Boot menu", among other things, like boot ad sd, boot ad nand, usb flasher..
So many "boot" words, it must be the bootloader i guess..
The volume down + power is to automatically sync your phone with the computer
I refuse to help you any more. You ARE being lazy, each ROM has a date next to it. You don't know what you're talking about yet you refuse to listen to me (trust me, I know a lot more than you on this subject) and you're not even making any sort of effort. Good luck sorting things out, but I just cba with you any more.
samnie25 said:
First of all, i'm not being lazy, you said to install a recent rom, i'm sorry i don't know which are the new ones and the old ones...
Second,..when you press volume down + power you will get to the HSPL which is an image splited in 4 parts, red, green, blue and white..
That screen its what you get by installing the HSPL and that is the thing missing in my htc , that it use to have but somehow it disappeared and i can't install it again because i can't sync my phone with the computer
The bootloader, you just hold the power button to enter it..
its the MAGLDR
At least in my phone when i hold just the power button it says there "Boot menu", among other things, like boot ad sd, boot ad nand, usb flasher..
So many "boot" words, it must be the bootloader i guess..
The volume down + power is to automatically sync your phone with the computer
Click to expand...
Click to collapse
As Nigel said, each ROM has a date which indicates the last time it was updated.
That is the bootloader screen, either SPL or HSPL. And it can't be "missing". Because if you don't have that, your device wouldn't even boot. You just didn't-know-how-to/couldn't get to it, but it's there.
Again, that screen can't disappear. You may be having issues with your volume rockers. As a matter of fact, your phone is bricked if you don't have that, as I stated earlier.
MAGLDR is indeed a bootloader, but it's not the device's main bootloader.
Wow, just wow. Not because there are many "boot"s, it's a bootloader. The main bootloader of the device is the H/SPL (volume down + end)
i.e. the main bootloader.
Click here for more information about HSPL and MAGLDR.
My volume rockers are working good.. First i thought they were not working well but i checked several times and they seem good.
When i press volume down + power it just goes to the MAGLDR and i know that it shouldn't go.. So i guess my HSPL disappeared somehow..
And i know that in order to install it again, the device must be sync with the computer, but i downloaded the htc sync and it doesn't recognize my phone.
Or as you said "that screen can't disappear" is there any other way to enter it?
... but ... seriously? After all what I had said, you still insist that you don't have HSPL and you need to install it?
Dude, without H/SPL, MAGLDR WILL NOT BOOT.
If you want to go to the bootloader, you must press and HOLD the volume down and boot WHILE STILL holding the volume down.
If you mean the bootloader then call it the bootloader, stop calling it 'the HSPL'. Try this solution from walts
walts said:
Hold Volume Down. Press and hold Reset until you see the BootLoader screen. Reset is the hidden button under the battery cover, lower left side below the SD card slot. You need a plastic or wooden stylus (toothpick will work). DON'T use a pencil, the graphite can get into the button and short it.
I just did it to be sure. It works.
HTH
Walt
Click to expand...
Click to collapse
hspl
Marvlesz said:
... but ... seriously? After all what I had said, you still insist that you don't have HSPL and you need to install it?
Dude, without H/SPL, MAGLDR WILL NOT BOOT.
If you want to go to the bootloader, you must press and HOLD the volume down and boot WHILE STILL holding the volume down.
Click to expand...
Click to collapse
I don't know if it is there or not.. i press volume down and power button and it just doesn't go to that colorful screen.. I've did it before, to get my htc back to stock with the windows mobile rom.
but now it doens't work,. it's like i am not pressing the volume down... if i hold volume down and hold power button it goes to the MAGLDR (Where we have a bunch of options) and if i hold volume down and just press power button (Without holding) it just loads the rom... it's like i am not pressing the volume down, but it is working, i can up and down the volume and i can go up and down through the option in the MAGLDR menu..
So, i don't know
But thanks
HTC
Nigeldg said:
If you mean the bootloader then call it the bootloader, stop calling it 'the HSPL'. Try this solution from walts
Click to expand...
Click to collapse
Just tried that, with the reset.. didn't work.
but thank.
I guess there must be some problem with the volume controller...
i will open the phone and try..
but thank you all for the time

Categories

Resources