Related
Hello all,
I was trying to get android booting from NAND instead of the SD card, I got a rom with 576ram (recommended) and installed MAGLDR 1.11. Now i cant seem to do anything with the phone, its not bricked as par say, it will show the loading screen and then not move and i can access the bootloader with voldwn+powerbutton but nothing else is happening, I cant load new roms nothing. Im pretty lost here and really need some help of how i can get my phone back onto a winmo6.5 rom so i can remember not to try it again
I posted this in this thread as it does relate to an android situation.
norodaigh said:
Hello all,
I was trying to get android booting from NAND instead of the SD card, I got a rom with 576ram (recommended) and installed MAGLDR 1.11. Now i cant seem to do anything with the phone, its not bricked as par say, it will show the loading screen and then not move and i can access the bootloader with voldwn+powerbutton but nothing else is happening, I cant load new roms nothing. Im pretty lost here and really need some help of how i can get my phone back onto a winmo6.5 rom so i can remember not to try it again
I posted this in this thread as it does relate to an android situation.
Click to expand...
Click to collapse
Find Task29.exe with no radio. It's on this site somewhere. You will see some with radios attached to them, so don't use those. Just the plain old no radio version. It will wipe your phones internal memory and you will basically be starting from scratch. Nothing will be on your phone after a Task29. Then go into bootloader. How to enter boot loader after Task29- Once Task29 hits 96% (looks just like you are flashing a rom), hold volume down and power from 96% until it gets to 100% and the tri color bootloader screen pops up. It should say "USB" at the bottom after bootloader comes up if you are plugged into your computer. Then Flash MAGLDR 1.11 again. Then flash your NAND build.
You aren't bricked if you phone powers on.
What operating system is on your PC?
Well it does boot and if you have hspl you did a good job. So if you have magdlr you now need to install Android. Read a guide plzzz!
Sent from my HTC HD2 using XDA App
OS on PC is....#sigh# windows vista ultimate
For task 29 do I have to have the phone connected via usb, because its not recognising it when its even in bootloader
task29.exe didnt work
Don't do task 29,you will just complicate your life even more than now. I don't think you know what you are doing.
You may brick your phone in the end do you have HSPL?
Sent from my HTC HD2 using XDA App
crisisinthecity said:
Find Task29.exe with no radio. It's on this site somewhere. You will see some with radios attached to them, so don't use those. Just the plain old no radio version. It will wipe your phones internal memory and you will basically be starting from scratch. Nothing will be on your phone after a Task29. Then go into bootloader. How to enter boot loader after Task29- Once Task29 hits 96% (looks just like you are flashing a rom), hold volume down and power from 96% until it gets to 100% and the tri color bootloader screen pops up. It should say "USB" at the bottom after bootloader comes up if you are plugged into your computer. Then Flash MAGLDR 1.11 again. Then flash your NAND build.
You aren't bricked if you phone powers on.
What operating system is on your PC?
Click to expand...
Click to collapse
1st try entering the BOOTLOADER, by pressing the volume down power button simultaneously..!!!
Instead of TASK 29, try FLASHAHOLIC which will perform your TASK 29 & help you flash a WinMO 6.5 ROM as well..!!!
PS: - You can even flash custom ROM's, stock ROM's not compulsory..!!!
norodaigh said:
OS on PC is....#sigh# windows vista ultimate
For task 29 do I have to have the phone connected via usb, because its not recognising it when its even in bootloader
Click to expand...
Click to collapse
Well then re-install Active SYNC or try on a diff PC with Latest Active SYNC..!!!
If you can access your boot-loader your device ain't bricked..!!!
Just boot your phone with VolDown and enter USB mode, reflash MAGLDR 1.11, once this has completed reboot your phone and hold down the power button, you will then see the MAGLDR menu.
Then just follow instructions on how to install an nand rom
http://forum.xda-developers.com/showthread.php?t=893948
it might just be the magldr or NAND ROM not flashed properly. If you can get to Tri-Color bootloader you are fine.
Found out the problem, thanks for all of your help guys, it was the fact i didnt have hspl2 installed....newb points to me
I have exactly the same problem only difference with my problem is when hold vol down and power buttons all I get is the tri coloured screen and nothing else no bootloader menu appears at all.
What can I do? Is my phn dead???
barryhd2 said:
I have exactly the same problem only difference with my problem is when hold vol down and power buttons all I get is the tri coloured screen and nothing else no bootloader menu appears at all.
What can I do? Is my phn dead???
Click to expand...
Click to collapse
That's exactly what is supposed to happen if you hold the vol down button while switching on. To get to the magldr menu you need to hold the power button in until it boots to the menu (no vol down button )
You guys are awesome!
I've been avoiding dealing with this phone for a while. This post came up first on google search. Held power and volume (mag 1.11 was on it) and upgraded it to 1.13 and now I'm golden! Thanks guys!!!!!!!!!!!!!
WM6.5 on my HD2 (from T-Mobile europe) has finally bothered me enough to decide to change the rom entirely, to android (NAND). I saw the instructions/video tutorial by techburrow (including the magldr v 1.11) and thought that it wouldn't give me too much troubles.
Before starting, I checked my ROM to see if it was recent enough. I as well installed hspl v 2.08 (as shown after taking battery out/in and using volume down + startbutton, in the rgbw screen).
After that I (think I) successfully installed MAGLDR v 1.11. It showed the comment that my phone was now "hacked".
I then went on to the most important step in the process, actually loading android. In the instructions for DFT_Android is states that:
" For installation you need enter MAGLDR (hold power button during boot)"
I tried getting into bootloader by holding the power button, I tried pressing it once and then holding it. Neither worked, both ended up with the HTC logo screen.
All I can do now is choose between getting the HTC logo and the rgbw screen showing hspl 2.08.
Hard reset also doesn't work, probably because MAGLDR deleted the original rom. Connecting through USB via the rgbw screen doesnt work, the connection is not recognised.
Other thread look similar problem, but haven't helped so far. Only the most recent are about others trying to get the android on NAND with MAGLDR 1.11 and DFT-Android.
HELP? Anybody has any idea on how I can install android any ROM now, how to get into the bootloader, how to use my HD2 again?
Looks like Magldr was not flash into the phone. Reflash magldr.
Sent from my HTC HD2 using XDA App
unfortunately
Thx for the suggestion, xhanay. However, reflashing MAGLDR requires an activesync connection and/or USB connection via HSPL (only way my phone does anything). Cannot get any connection unfortunately. So no reflashing.
Any other suggestions? (reflashing via microSD?)
help!i have the really same problem!thx!
This is what I do:
1. Remove the battery, put it back
2. Hold VolDown key pressed while turn on the phone to enter Bootloader (tricolored screen)
3. Connect it to PC and wait for connection to change to USB
4. Flash radio 2.15.50.14
5. Hold VolDown key pressed after reboot to enter bootloader again.
6. Flash MAGLDR
7. Reboot
8. Hold Power button pressed > Select USB flasher ...
....and flash Android/Windows 7.
If USB connection is not recognized I suggest flashing a stock ROM using SD card.
See instructions here, chapter 3 - Flashing Via MicroSD Card
could just work
Thank you for the quick response. Hopefully I will make it all the way to step 8+ (with android and all apps coming along with it). Otherwise using the stock rom should help. Thx for the link.
Will let you know if it works.
Also post in the right section in the future
All worked. I had to reflash a custom ROM through the rgbw screen (apparently a custom ROM did synchronise via USB even though activesync didnt show anything). Then I reinstalled MAGLDR (which immediately sent me through to the bootlader screen). After I had some issues loading android (had to tag USB on in Activesync connection settings, make the connection, the tag USB off in the connection settings)... Now Android is running as I hoped it would. Great work and thanx to all that helped.
ps: Will try to use the right section next time. No promises that it will then be the right one however.
I have the same problem and tried this only to be sent back into magdlr where it just scrolls up and down with the volume key held down.
Any suggestions much appreciated.
dixieuk101 said:
I have the same problem and tried this only to be sent back into magdlr where it just scrolls up and down with the volume key held down.
Any suggestions much appreciated.
Click to expand...
Click to collapse
you could try .... than just plug-it in using activesync and run HSPL3... do not install it...before installing it will put ur phone in bootloader....than exit HSPL3 keep your phone pluged in and just flash wtever....radio,rom...etc....
OR
Press together VOLUME DOWN - DO NOT LET GO! EVER TILL IN BOOTLOADER & RESET RED BUTTON - under batt. metal cover -
after few seconds the tri-coloured screen will appear
load the hard SPL than magledr than rom it works 100%
Same Problem!!!
Hey i have the same problem. Recently I bought this phone off of craigslist. The phone goes to the DFT screen and its on aMAGDLR v1.11. I tried to reset it but it doesnt go to the multi colored screen. I bought a new micro sd but that didnt work. It also cant connect to my computer. There isnt wrong with the charging port because the light goes on when its connected. PLEASE HELP?! I cant go into bloatloader. Is it bricked?
Hi,
I had used HD2ToolKit4.2.0.1.zip and use Wipe option given in the bottom left.
Regards
my volume key not work and now i cant use the bootloader,please
hey anybody here??????????????
now what is soluton for this bootloader nogo
stucked between magldr and dft screen
pls help
now what is soluton for this bootloader nogo
stucked between magldr and dft screen
pls help
Click to expand...
Click to collapse
did you do this with right order?
http://forum.xda-developers.com/showpost.php?p=27057672&postcount=127
hi guys i flashed my htc hd2 wm6.5 to nand android rom in 1st 1 week of usage i have no problem and enjoyed the nand android rom in my htc hd2 until one day my hd2 hang and when i reboot my unit it was hang on splash screen only....
i reflashed it using magdlr ver. 1.11 into the same nand rom im using but i have no luck...it still stock on tje android splash screen...what will i do guys?
im planning to flash it to wm6.5 rom,but what will i do?it never boot on tri color screen it only boot on magdlr screen
and how can i flash it wm6.5 rom cook or stock rom i want to revert it back to wm6.5
my hd2 running on gingerbread 2.3.3 nand(V1.8) rom before it malfunction..
Well, my forensic analysis has come up with the following technical and somewhat difficult solution to your present problem: "Click the search button"
Now I know it may sound intimidating, but I tested that feature out for you and came up with this:
http://forum.xda-developers.com/showthread.php?t=905841
matt
Shut down completely your phone (remove batter for 15 sec too)
Place battery back and now hold volume down button.
Still hold volume down button and switch on your phone.
You get 3 color screen.
Now attach your usb cable and connect it to PC
Find on this forum your phone stock win mobile rom (link to officila roms thread)
Run stock win 6.5 rom exe (this is sample name: RUU_Leo_S_HTC_WWE_EastEurope_3.14.479.2_Radio_15.42.50.11U_2.15.50.14_LEO_S_Ship.exe)
Follow instructions on your PC screen. On final your phone reboots.
Enjoy your stock phone.
hi datasoft thanks for the quick reply...
i try your suggestion to enter into bootloader mode but it booted on the magldr screen...
can i flash wm6.5 rom into magdlr usb flasher?
siapelbo said:
hi dasoft thanks for the quick reply...
i try your suggestion to enter into bootloader mode but it booted on the magldr screen...
Click to expand...
Click to collapse
Switch off, hold vol down button in and switch on.
As ClydeB1, states you must hold the vol down only and not hold the power button.
siapelbo said:
hi dasoft thanks for the quick reply...
i try your suggestion to enter into bootloader mode but it booted on the magldr screen...
Click to expand...
Click to collapse
when you get ready to power back on you have to hold volume down and keep holding it while is booting and it should switched to the tricolored screen, plug the usb cable and it should say usb at the bottom when it connects, and if you have hardspl which I know you have after running android, you can use any custom winmo6.5 rom it doesn't have to be an official rom.
can i flash wm6.5 rom into magdlr usb flasher?
No, flash from bootloader.
awts...i cant enter into booloader mode....im so sure what im doing i sure i follow the instructions of you guys....holding down the vol button and switch on
Are you holding it at the bottom of the button and not in the middle or top, ie as if you are turning the volume down?
I don't think you can flash WM6.5 with flasher. You have to restore from recovery screen by remove battery and restore.
ClydeB1 said:
Are you holding it at the bottom of the button and not in the middle or top, ie as if you are turning the volume down?
Click to expand...
Click to collapse
yeah im sure i was holding down the volume botton and switch the power on
Does the vol down button work normally in the Android rom or when moving around in magldr. To be sure, remove the battery and leave it out for 10 minutes then put the battery back, leave the cover off and try again.
I have heard of one or two users who have also had a problem where the vol down button stopped working. If that is the case there is no way back AFAIK.
ClydeB1 said:
Does the vol down button work normally in the Android rom or when moving around in magldr. To be sure, remove the battery and leave it out for 10 minutes then put the battery back, leave the cover off and try again.
I have heard of one or two users who have also had a problem where the vol down button stopped working. If that is the case there is no way back AFAIK.
Click to expand...
Click to collapse
volume botton is perfectly working it work around in magdlr mode actually i flashed my hd2 into android rom right now flashing is done without problems, but its not boot normarly it boot only in splash screen....
can you guys post a link of task 29...i will try this method and flash stock rom
but the main problem is i cant enter into bootloader mode
I use this tool for Task29 - http://forum.xda-developers.com/showthread.php?t=917807
Once you run Task29 though it will wipe the NAND memory and magldr and if you can't get back to bootloader mode then you will be stuck on the splashscreen.
Hi,
I'm also having problems, but in my case the progress bar on my phone when installing the new ROM stops at 0% and will stay there indefinably. On my computer a connection problem will be raised.
The same happens with task29.
I've also tried decompressing ROM Utility, putted leoimg.nbh on my 2GB fat32 formatted sdcard, hold down the volume key.
I will get a new screen with "Loading..." on it, but it freezes there.
So, I have no idea what I'm doing wrong.
Any help will be appreciated.
Regards,
temporary_24 said:
Hi,
I'm also having problems, but in my case the progress bar on my phone when installing the new ROM stops at 0% and will stay there indefinably. On my computer a connection problem will be raised.
The same happens with task29.
I've also tried decompressing ROM Utility, putted leoimg.nbh on my 2GB fat32 formatted sdcard, hold down the volume key.
I will get a new screen with "Loading..." on it, but it freezes there.
So, I have no idea what I'm doing wrong.
Any help will be appreciated.
Regards,
Click to expand...
Click to collapse
Are you sure you still have hspl installed? In bootloader, check your spl version- it should end in hspl.
ClydeB1 said:
Are you sure you still have hspl installed? In bootloader, check your spl version- it should end in hspl.
Click to expand...
Click to collapse
Hi,
Yes. I had one with a 8 on it. I've installed the other, and it worked (or the other way). Thanks.
Regards,
guys my phone revive with a jtag procedure i went to a technician shop here in the phillipines
my phone running in stock rom again...
EDIT: I have a guess about the cause of all these issues. It looks as if the phone behaves like the "call" button is being in a pressed state all the time. If the result of the below listed steps is the same when doing them, but with the "call" button pressed, that would confirm it. Can someone please do it?
EDIT2:
Success! Well, kind of. I downloaded Copes CyanogenMod 7 v 02/04/11 [Kernel: AmeriCanAndroid HK853+] SD MAGLDR ROM. I went through all the steps, and then realised there is a rel_path set in startup.txt. I removed it, since I'm doing everything in the sd root directory (as I can't select anything in the MAGLDR menu), and tried to boot. It got past the GO!GO!GO!, and booted Android. Unfortunately, as I feared, the digitizer is not working and I can't select the setup wizard in the dialog that is presented on first boot. I now took the battery out and back in, and it seems the boot process is stuck on htc splash screen, which is shown *after* the GO!GO!GO!. I guess it's all down to hardware now.
--
I got this HD2 the other day in an unbootable state. When I turn it on, first I get the HTC splash screen, MAGLDR menu appears briefly and then MAGLDR 1.13 tries to boot Android form the SD card. However, there is no kernel on the SD CARD, the error about it is shown on the screen and then MAGLDR menu is briefly shown again and the same thing repeats over and over. What I tried is the following:
1) holding down the power button while booting to get the MAGLDR menu, but the same thing happens
2) pressing some buttons -> while holding down the windows button, MAGLDR menu is presented. If I press the volume down button, the loop continues, if I press the volume up button, it tries to boot Windows Phone 7, but it can't find any. If I just let go the windows button, the loop continues
3) putting android on an SD Card - I chose the BoxmaX ROM - I took all the files from BoxmaX.KS.v8.6.KH8.5.1.rar\Android folder and put them to the root of the SD Card - now MAGLDR finds the kernel, boots it, but is then stuck on the GO!GO!GO! line
4) holding the volume key down and pressing end-call button, in order to get to the boot screen and see the radio version and try to flash the WinMo ROM - I can't get to the bootloader, it never shows. Instead I get the splash screen and the MAGLDR as usual
5) come to XDA and ask for help - so, what are my options now? Is there any way to get it to work?
The thing about the phone is that it could have been partially disassembled, so maybe some buttons don't work because of it (I suspect the volume down button, but it reacts while holding the win key). The digitizer too, is probably not responding, but I can't get to any screen where I could be able to test it.
P.S. I'm a HD2 newbie, never had it before, so please forgive any beginners mistakes.
Just a question.. you prefer booting from SD or the phone?
Right now I don't care. I just want to make it do something. In general, I prefer booting from NAND.
Have you try reinstalling magloader?
I'm not at home right now, but for sure we will get this to run... I will give you one big instruction rather asking you single questions... we will start from scratch... 3 steps
Brb 4hrs unless you found your answer
Booting from nand
1. Reinstall hspl... make sure its the right one for your phone. Get in bootloader to do this.
2. Reinstall magloader... 1.13... I believe that's the one...
3. Install a DAF version of rom... then we will get clock work on there since that's the preferred way of flashing rom IMO.
Hope this help you get started... ill keep checking back on you.
Thanx for your help. See my second edit in the first post.
Unfortunately I still can't enter the bootloader, so I can't flash either HSPL, or a WinMo 6.5 ROM.
Notice you say call button seems to be in pressed mode... if that's the cause try to get that fix... to get to it you have to remove digitizer... getting that fix that will help a lot.
I never mess with SD boot so I would not know how to help you in that but if its a nand boot... I know
you might have got the wrong daf configurations or defective hspl or magldr
Have you checked your battery pins to see if one is bent slightly. one of the battery pins being bent has been know to cause boot loops. Worth a good look at the battery pins for sure....
Thank you all for the advice. I disassembled the phone today, disconnected the keypad flex cable, tried powering it on with the volume button pressed and, lo and behold, bootloader screen appeared. So, I'll order a new keypad flex cable, and try it then.
alh84001 said:
Thank you all for the advice. I disassembled the phone today, disconnected the keypad flex cable, tried powering it on with the volume button pressed and, lo and behold, bootloader screen appeared. So, I'll order a new keypad flex cable, and try it then.
Click to expand...
Click to collapse
Ciao!
I have same problem...
But my volume button right works with normal multimedia or phone calls...
Do you think I need too a new cable?
:-?
(excuse me for my english!)
help urgent
can someone help me i got an htc t8585 bouygue telecome french but when i install magldr phone restart successfull and hang on htc logo
how to do? excuse for my english
amsizi said:
can someone help me i got an htc t8585 bouygue telecome french but when i install magldr phone restart successfull and hang on htc logo
how to do? excuse for my english
Click to expand...
Click to collapse
Welcome to the forum. What radio do you have? Switch on while holding volume down and tell us exactly what is on the bootloader screen. I think that is right.
For more info
my bootloader show PB81100 HX-BC
SPL-2.08.HSPL 8G XE
0*05
CotullaHSPL 0*50
I still think it is your radio, see https://forum.xda-developers.com/showthread.php?t=1021837 and https://forum.xda-developers.com/showthread.php?t=611787
First things first.....first post!
Ok so I have the HD2 512 version and have put hspl 2.08 on it with no problems but when I have tried loading magldr1.13 the install seems to go ok on the phone but when it reboots magldr doesnt launch it simply stays on the default white htc launch screen.
My own fault for following a youtube video I guess.
The handset lets me reflash magldr which I did a couple of times and I tried an older version of magldr and also used the nand toolkit to try and install magldr but still the same white screen on launch.
Any ideas whats going on anyone? help appreciated with thanks
PeteLeMeat said:
First things first.....first post!
Ok so I have the HD2 512 version and have put hspl 2.08 on it with no problems but when I have tried loading magldr1.13 the install seems to go ok on the phone but when it reboots magldr doesnt launch it simply stays on the default white htc launch screen.
My own fault for following a youtube video I guess.
The handset lets me reflash magldr which I did a couple of times and I tried an older version of magldr and also used the nand toolkit to try and install magldr but still the same white screen on launch.
Any ideas whats going on anyone? help appreciated with thanks
Click to expand...
Click to collapse
Are you sure you installed HSPL correct? Hold down the volume button and press the power button, till the rainbow screen, does it say something about cotulla hspl? If yes, connect the phone to the computer(still in the rainbow screen of course) and wipe the device(task29). After that your device will be totally clean and the correct radio is installed. So you will have to press the volume down button again to enter the rainbow screen and then install magldr.
Yes it does say cotulla.
So I tried what you said I connected in rainbow screen and pressed wipe(task 29) in the nand toolkit (wipe from the toolkit right?) but in the rainbow screen it says cotulla still,
tried magldr again, same white screen
when you saying "launching Mgldr", are you pressing the power button(end key) when the phone boots? this way only you enter Mgldr and loads the menu
Yes I have tried holding the power button on powering on the device and tried it without holding, still the same white htc screen and no movement from there.
When I wipe the handset it still has SPL-2.08.HSPL on it and still says CollutaHSPL.
I'm guessing I should try and restart from scratch??
you havent flashed a compatible radio yet, , magldr wont start without it.
enter bootloader
usb
flash radio 2.15.50
reboot
magldr.
Ok I will try that now. Is radio 2.15.50.14 ok?
Wahey! I'm in!
Thanks very much you guys are legends!
Right next step haha. Don't worry I'll read up on it don't want to hassle anyone.
Any suggestions what are the best roms for WP7 or ICS??
(and if you have time point me in the right direction of them)
Any other step I am missing?
Again thanks for your help
Different people, different needs
Check some threads (also Search, will not hurt you )
http://forum.xda-developers.com/showthread.php?t=1656171
http://forum.xda-developers.com/showthread.php?t=1430276
http://forum.xda-developers.com/showthread.php?t=955268
http://forum.xda-developers.com/showthread.php?t=1678153
http://forum.xda-developers.com/showthread.php?t=1670456
Flashing guides - in my signature