Database Users

Maybe someone can rescue me (quick! EEK!)

Hi all,
Maybe someone can help me out!
I am stuck at work - cant even really surf but had to post as I just feckered my mates HD2!
BOOOOO!!
So I installed HSPL and its still there.
Flashed up to energy ROM (APRIL 1st)
Then got stuck in reboot cycle - phone wouldnt boot unless it had power plugged in.
Took battery out of it and put mine in it which had higher charge - not much.
Then I got it booted into 6.5. Customised and changed settigns for Vodaphone.
Rebooted and phone stuck in loop again.
Couldnt get back into Vodaphone.
Went to bootloader and then used the official:
RUU_Leo_HTC_WWE_1.48.405.2_Radio_Signed_15.28.50.07U_2.05.51.05_2_Ship.exe
Flashed the bugger.
Then tried to boot again.
No boot without power inserted
Phone will not complete boot even with power
gives HTC white welcome, shows ROM etc
vibrates backto HTC white welcome.
Rinse
Repeat
Can anyone give me any ideas what I can do with this? He is coming to get it at 5.30; I am meant to have FPSECE Morph gear and all sorts of other shizzle for him
He is going to get a brick
any ideas would be GREATLY welcome.
no flames please if I missed something, I am desperate to sort this quick and quiet.

Try make Task29 and then reflash Radio and ROM, it could help you i think...

Have you installed radio 2.08 ?
You should. You can install it by downloading it and use customRUU to install the file.
Put phone in bootloader first.
Your mate's phone will be revived

What radio do you have installed. The NRG roms require radio 2.08.50 in order to boot.

Yea sounds like a radio issue. You didn't mention what phone? US Tmo HD2 or everywhere else HD2?

Is GSM HD2
I have done all above task 29 new radio - loads of roms.....stuck in circle.
Phone will not boot without apower lead in it
Ahh feck [email protected]

What version radio does it read then when you are stuck in your bootscreen ?
is it still 2.06 or 2.08 now ?
Installing HSPL doen NOT upgrade your Radio.
What is your SPL version ?
And "fecking ass" is groce. Try fecking some koent.

lucid said:
Have you installed radio 2.08 ?
You should. You can install it by downloading it and use customRUU to install the file.
Put phone in bootloader first.
Your mate's phone will be revived
Click to expand...
Click to collapse
ClydeB1 said:
What radio do you have installed. The NRG roms require radio 2.08.50 in order to boot.
Click to expand...
Click to collapse
Actually they dont require 2.08... they require a radio without .51 numbering.
You can use
2.07.50.27
or
2.08.50.08
either will work just fine.

misticjeff said:
Actually they dont require 2.08... they require a radio without .51 numbering.
You can use
2.07.50.27
or
2.08.50.08
either will work just fine.
Click to expand...
Click to collapse
True, I use 2.07 (old signature LOL), but just mentioned 2.08 as it's the recommended one.

Oh ****e
Ok all,
Big warning to all here:
See my attached image.
I bent the left most battery connection pin out a tiny little bit - so little I didnt notice it.
Then the phone would obviouslly only boot without the power plugged in.
The pin was being pushed out! and not connecting with the battery.
I bent it back and it booted whilst I was explaiing that I was having teething trouble with his new ROM.
HAHA
Thanks VERY much to all for ideas and fast feedback - really thought I done it in then! Bloody hell Id have had to give him mine!!!
OH NOOOOOOOOOOO!!
@ the try some Koent line......OH GOD LOLOLOL
Waht with the relief of fixing the device and a joke like that, I was ROFL ing it - Not RALPH ing it...
Thanks again all

Yarod, the above advice for the radio version applies only to the custom rom.
By flashing a factory rom from the memory card you have probably overwritten hspl which is why this dosen't boot.
First thing to do is reflash hspl in the bootloader, via usb. If you remove your memory card and hard reset, then you should get a working phone. Assuming it's a vodafone branded handset you can use a vodafone branded rom without the need for hspl - there's a 1.66 version up on the uk site.
If you want a custom rom, use hspl and check the radio requirements before flashing
and most importantly flash via the usb only to avoid overwriting hspl.
hth,
mike

hah! bent pin, nice one. Bet you felt a huuuge wave of relief wash over ya when it booted eh? Gotta love that post adrenaline comedown.

here we go again with another victim....
1. Hard reset
a. turn off your HD2
b. hold Volume up and down and press end button till it will vibrate show white screen that you wanna hard reset
c. release volume up and down
d. press volume up for continue Hard reset
e. press volume up for continue boot up
it will boot up your device...
2. install radio for energy click here or herefor download
3. Use Customs RUU from here
4. flash your radio
5. now you are good to go....
i hope this helps i know how you feel cause i had same problem and this phone worth a lot so... take care...

yarod_g14 said:
Hi all,
Maybe someone can help me out!
I am stuck at work - cant even really surf but had to post as I just feckered my mates HD2!
BOOOOO!!
So I installed HSPL and its still there.
Flashed up to energy ROM (APRIL 1st)
Then got stuck in reboot cycle - phone wouldnt boot unless it had power plugged in.
Took battery out of it and put mine in it which had higher charge - not much.
Then I got it booted into 6.5. Customised and changed settigns for Vodaphone.
Rebooted and phone stuck in loop again.
Couldnt get back into Vodaphone.
Went to bootloader and then used the official:
RUU_Leo_HTC_WWE_1.48.405.2_Radio_Signed_15.28.50.07U_2.05.51.05_2_Ship.exe
Flashed the bugger.
Then tried to boot again.
No boot without power inserted
Phone will not complete boot even with power
gives HTC white welcome, shows ROM etc
vibrates backto HTC white welcome.
Rinse
Repeat
Can anyone give me any ideas what I can do with this? He is coming to get it at 5.30; I am meant to have FPSECE Morph gear and all sorts of other shizzle for him
He is going to get a brick
any ideas would be GREATLY welcome.
no flames please if I missed something, I am desperate to sort this quick and quiet.
Click to expand...
Click to collapse
Hey! I did the same mistace, u need to download HSPLv2 , Install 2.06.0000
Then volume down + power botton, install stock ROM from HTC.com, and reboot.
That worked for me, hope it works for you.
Cheers.

lol
hi all this is fixed see my previous post, i had bent the battery pin - so small didn't notice it. i wonder if anyone else has suffered from this?
many thanks
i am tempted to fart in the general direction of the "another victim" statement
I'm a fixer not a victim lol...

yarod_g14 said:
hi all this is fixed see my previous post, i had bent the battery pin - so small didn't notice it. i wonder if anyone else has suffered from this?
many thanks
i am tempted to fart in the general direction of the "another victim" statement
I'm a fixer not a victim lol...
Click to expand...
Click to collapse
It just happened to me!! A billion thanks mate

Another reboot loop victim...
Bent battery pin seems to have been the culprit for me as well! sat on charge now to get it to 100% before I start reinstalling cabs and stuff.

HTC HD2 rom change with non working screen

Hello Everyone.
TBH im my opinion you guys are my last hope to fixing my hd2.
So here's the problem.
I have a HD2 that turns on but does not have a functioning touc screen.
ABOUT MY PHONE:
HTS HD2
Has old android in it ( I dont know which one it is, but i can describe it. It starts up with a BootLoader asking to boot android, so i have the option to press yes or no. It has old blue theme in the background.
Here's the problem. I've called HTC support and i learn my phone still has manufacturers warranty. So basically i can just send in the phone, and ill id have to pay is shipping. BUT! here's the problem. HTC does not approve of third party software installed in the phone, in my case it is the ANDROID. So now im trying to wipe android put, and install windows mobile again. I downloaded the t-mobile stock rom and when i plug in my phone, the windows mobile center automatically pops out but it shows an error symbol.
TL;DR
So my question to you guys is how do i remove Android and install Windows Mobile on an HTC HD2 with a non working screen
Thank you so much guys for even considering to help me
Mod if i posted on the wrong section could you please move it for me.
Thanks

hi,
try this:
http://forum.xda-developers.com/showthread.php?t=956715

Thanks so Much But here's an update
I went ahead and downoaded the HSPL3
I turned on my phone and also pressing the voulme down button which brought to me to a red green and white color. I had my phon conneceted to the computer VIA USB. I first double clicked the T-Mobile rom update thingy and went ahead accpeted the warning signs etc,so the first thing that came up was identifying phone, and after 5 seconds it disappears so nothing came fro that, then later i double clicked the HSPL3 which asked me to either pick the 2.8 or the the 2.8 spl i believe, i had the spl installed so i wen ahead clicked the 2.8. it installed and my phone rbooted and BAM my touch screen worked, and when it asked to boot android i pressed NO. my phone rebooted and iagain the boot loader came up and asked to bott android, so this time i pressed BUt it didnt work because the touch screen stopped working!
So i went ahead to try everything all over but this time i clicked the 2.8 spl and after a minute on my phone it displayed " we hacked it" etc etc etc, i robooted my phone, ad it worked, i turned it on and off twice and it worked i was using my phone after a month So after playing with it alittle bit i decided to put my sim card in it. I turned off the phone and put the Sim card and turned on the phone so i can use it but.....once again the touch screen stopped working... ****!!!!!!

yep, now the touchscreen is once again not working

bump bumpity bump

fusion1204 said:
bump bumpity bump
Click to expand...
Click to collapse
Download a stock WM ROM for your phone, extract and rename your .nbh to leoimg.nbh. Transfer leoimg.nbh. to your SDcard.....enter bootloader mode....there it will flash back to your WM ROM with all HSPL remove. Time to send back to Manufacturer for repair..

Okay hold on. So when you see stock WM ROM coud that be the "T-Mobile_HD2_MR_Software_311...." file? and where can i find my .nbh file?

fusion1204 said:
Okay hold on. So when you see stock WM ROM coud that be the "T-Mobile_HD2_MR_Software_311...." file? and where can i find my .nbh file?
Click to expand...
Click to collapse
extract that from your .exe file.
Stock ROM can be found here
http://forum.xda-developers.com/showthread.php?t=655653
Make sure you use the Stock ROM specific for your phone, else you will brick your phone.

I went ahead and did that, but nothing changed did i do something wrong?

fusion1204 said:
I went ahead and did that, but nothing changed did i do something wrong?
Click to expand...
Click to collapse
Try following this guide....
http://forum.xda-developers.com/showthread.php?t=681317

10507 Thank you for the links but it didn't wok for me.
UGh!
Am i doing something woring? i mean i can get to the screen where it shows the foru colors, i guess that would be flashing and once i get there i can't do anything else the only way for me to do anything while im on that screen is if i have it connected in with my computer, and also start runinng the HSPL program which switches from Hspl to a NON hspl vice versa.
I hope youre not tired of me lol!
please help me out with this stupid situation im in.
Thank you.

Bumpity bump please help me out

[Solved] Magldr 1.13 GO GO GO stuck

hi
so my phone was doing very good on android , magldr worked fine, no GO GO GO error but when i replaced my hd2's LCD magldr stucked on go go go on it's way to boot android from nand.i thought "ey, no big deal maybe it's the lcd's driver"! but i didi every thing to boot my phone on android again and still no chance heres waht i did:
1:task29->SPL 2.08.0000->SPL 2.08.HSPL->magldr
and it stucked on GO GO GO on tetris.so obviously there was no chance to pass the problem when i installed recovery and tryed to load it.
2:task29->SPL 2.08.0000->SPL 2.08.HSPL->cLK
And this one stucked on "no_console_suspend=1" or something.
i'm so hopeless guys.could someone please help me?

any one?

Firstly, why did you have to get your lcd changed??? I recently changed my lcd and digitizer because I had the common screen freeze. The change to my screen did not affect my magldr.
What radio are you running?? I had similar problems abd it ended up being wrong radio, but this was also before I got my lcd changed.

tazphoenix said:
hi
so my phone was doing very good on android , magldr worked fine, no GO GO GO error but when i replaced my hd2's LCD magldr stucked on go go go on it's way to boot android from nand.i thought "ey, no big deal maybe it's the lcd's driver"! but i didi every thing to boot my phone on android again and still no chance heres waht i did:
1:task29->SPL 2.08.0000->SPL 2.08.HSPL->magldr
and it stucked on GO GO GO on tetris.so obviously there was no chance to pass the problem when i installed recovery and tryed to load it.
2:task29->SPL 2.08.0000->SPL 2.08.HSPL->cLK
And this one stucked on "no_console_suspend=1" or something.
i'm so hopeless guys.could someone please help me?
Click to expand...
Click to collapse
Flash the stock Windows Mobile ROM for your HD2. If it sticks on boot up you have a hardware issue (bad or corrupt NAND), if it boots up you just don't have something right about the software.
Last thing are you sure you downloaded and flashed the MAGLDR version of the ROM you want to use, unless the ROM will work with MAGLDR and cLK, it is aq couple of ROMs that will work with both.

atsavlis said:
Firstly, why did you have to get your lcd changed??? I recently changed my lcd and digitizer because I had the common screen freeze. The change to my screen did not affect my magldr.
What radio are you running?? I had similar problems abd it ended up being wrong radio, but this was also before I got my lcd changed.
Click to expand...
Click to collapse
I had my LCD changed because couple of weeks age i was on beach and dropped the phone on wet sand and went for swimming.so it was there for like 2 hours and when i got back and checked it it was a some kind of stain on it the it bothered me.
the radio is: 2.15.50.14
thanx for reply.

T-Macgnolia said:
Flash the stock Windows Mobile ROM for your HD2. If it sticks on boot up you have a hardware issue (bad or corrupt NAND), if it boots up you just don't have something right about the software.
Last thing are you sure you downloaded and flashed the MAGLDR version of the ROM you want to use, unless the ROM will work with MAGLDR and cLK, it is aq couple of ROMs that will work with both.
Click to expand...
Click to collapse
i have magldr 1.13 flashed on my hd2 and it even stuckes when i want to load tetris or when i want to load ad recovery.it's not the rom problem.
and sure i'll flash the stock room as soon as posible and let you know the results.

tazphoenix said:
hi
so my phone was doing very good on android , magldr worked fine, no GO GO GO error but when i replaced my hd2's LCD magldr stucked on go go go on it's way to boot android from nand.i thought "ey, no big deal maybe it's the lcd's driver"! but i didi every thing to boot my phone on android again and still no chance heres waht i did:
1:task29->SPL 2.08.0000->SPL 2.08.HSPL->magldr
and it stucked on GO GO GO on tetris.so obviously there was no chance to pass the problem when i installed recovery and tryed to load it.
2:task29->SPL 2.08.0000->SPL 2.08.HSPL->cLK
And this one stucked on "no_console_suspend=1" or something.
i'm so hopeless guys.could someone please help me?
Click to expand...
Click to collapse
hmmm... it seems to me that your LCD screens wasn't attached properly but maybe I am wrong.
The best way as T-Macgnolia said is to flash original WinMo to first check if everything is working fine.
After that if everything is working fine:
1) make sure you have proper radio installed (2.15...)
2) Do Task 29 (no need to reflash HSPL and Radio)
3) Flash MAGLDR or cLK
4) Flash CWM
5) Make sure the ROM you are using is for either MAGLDR or cLK.

i too have had this issue. after i flashed stock rom the touch screen (digitizer) didnt work. yesterday i dropped phone off to shop to have digitizer replaced. i will let u know the outcome whenever i get the phone back (they told me they will call me today to give me an update)

I had the same problem. I removed the SD card and it booted up normaly. I reformated the SD and reinstalled. No more problems.....so far....

Well after installing stock rom it turned out it was digitizer.like og92 said.

yea i still havent received my phone yet. but this is the second time the digitizer went out on me. the first time i could at least boot to android. but now it wont let me boot into anything (other than touchless winmo). my bet is that there is a conflict with the digitizer driver and nand as stated in op. unfortunately since i dont have my phone, i have no means of troubleshooting. i hope to report back with update soon
p.s.: why has this thread been marked as solved when it is not?

turns out it wasn't the digitizer (at least not in my case). Instead it was the flex cable (which incorporates the following components: the antenna connector, the front speaker holder, the vibe motor holder, the camera holder, the volume button flex cable ribbon and some other IC components.). I think that it sucks that now i have to pay another 100+ because only the lcd/digitizer was warranted even though you must tamper with the flex cable ribbion in order to replace practically anything within the phone... but its their word against mine (as well as no written contract). Anyway it does make sense that this component is failing (otherwise android would boot) so i think it would be safe to categorize this one as a hardware issue!

Need help after bad flash.

So basically i tried to flash android this was my first time doing any of this & it stuffed up badly now all my phone does is boot up into the white htc logo screen & won't get past there. It use to have 3 sets of numbers on the side but now it doesn't. I tried to go into the recovery boot loader screen. I use to be able to get into it but it never did any thing. I took it to a phone shop & they said i had water damage I never put the phone near water what so ever but they said it because my friend pressed the red button on the back which tells you have water damage. If anyone could help i would be so appreciative the phone i have now seems to be a pile of crap compared to the HTC!
Thanks in advance.

Hey
I dont no how i say that in english but i try IT.
Look at the pins of your Batterie so if the are have contact.
I hope you now what i mean.
Sent from my NexusHD2 using XDA App

I'll give that a go, I'll let you know of it works thanks

justblayzee said:
So basically i tried to flash android this was my first time doing any of this & it stuffed up badly now all my phone does is boot up into the white htc logo screen & won't get past there. It use to have 3 sets of numbers on the side but now it doesn't. I tried to go into the recovery boot loader screen. I use to be able to get into it but it never did any thing. I took it to a phone shop & they said i had water damage I never put the phone near water what so ever but they said it because my friend pressed the red button on the back which tells you have water damage. If anyone could help i would be so appreciative the phone i have now seems to be a pile of crap compared to the HTC!
Thanks in advance.
Click to expand...
Click to collapse
I dont know who told that bull**** but the red button on back is a reset switch, it has nothing to do with water damage.
To me it just sounds like you have task29 and not actually flashed magldr yet.
Hold down the volume down button while powering on phone, keep hold of volume down button until you boot into bootloader. Once in bootloader launch the HD2 Toolkit and flash magldr. Once you ahve installed magldr choose USB Flasher from magldr menu and then repartition using the toolkit.
Once you have partitioned to teh required size for you rom just flash teh zip file using CWM.
Since this is your first time flashing android on HD2 I would recomend looking at forum for a bit and reading guides because its obviosu you just jumped in and didnt read much.

TheATHEiST said:
I dont know who told that bull**** but the red button on back is a reset switch, it has nothing to do with water damage.
To me it just sounds like you have task29 and not actually flashed magldr yet.
Hold down the volume down button while powering on phone, keep hold of volume down button until you boot into bootloader. Once in bootloader launch the HD2 Toolkit and flash magldr. Once you ahve installed magldr choose USB Flasher from magldr menu and then repartition using the toolkit.
Once you have partitioned to teh required size for you rom just flash teh zip file using CWM.
Since this is your first time flashing android on HD2 I would recomend looking at forum for a bit and reading guides because its obviosu you just jumped in and didnt read much.
Click to expand...
Click to collapse
Thank you, I haven't played with this phone for ages & now I'm pretty experienced in android ill try your suggestion but would be nice to have a spare phone.

my htc hd2 is STUCK.. HELP ME PLS

I bought an HTC HD2 FEW WEEKS BACK FROM ONE OF MY FRIEND.
I DO NOT HAVE THE HISTORY OF WHAT HE TRIED TO DO WITH IT.
BUT BECAUSE IT WAS STUCK/DEAD , HE GAVE TO ME FOR CHEAP.
NOW THIS PHONE IS UNDER WARRANTY TILL AUG-2012 AND IS FROM VODAFONE.
(EVEN AFTER INSTALLING ANDROID IT IS VOID)
HE MUST HAVE TRIED SEVERAL ROM/HSPL TO GET TO THIS POINT.
PROBLEM:
When I power up the phone, it displays a NRG LOGO SCREEN (energize software), and it gets stuck on it forever.
When I do hold the volume down + power button, then it comes up with the three colour screen and it says SPL-2.08.0000, AND also says rom update failed (only if i try to install and then start up)
The phone does connect through USB when it is on the three colour screen, but it does not let me install ANY OF THE romS or the spl'S...
I have tried literally every single step possible. I have tried to do task 29, i have tried install the original rom, i have tried to put the rom in the sd card and try it that way.. I have also tried to do hard reset... vol up and down and it does not complete either..
I best rom it let me install was 99% of 2.10.50.19.2.. but after 99% it got stuck .. it seems like it gets stuck within 1 min or so.. anything you do!
Some times after several hundred attempts, it does let me change the spl... as it was displaying 3.... before then i changed to 1.4..... and then to 2.08...
All i want to do is to get rid of the NRG SCREEN, so i could send to the htc ,, for repair ( i know that it is not under warranty if i used andriod, but they will not know) .. or is there any way to completely format the phone,,, is there any solution to install andriod or microsoft? pls help

Before we start, you can ask him how his device has ended up like this, can't you?
boxboy said:
I bought an HTC HD2 FEW WEEKS BACK FROM ONE OF MY FRIEND.
I DO NOT HAVE THE HISTORY OF WHAT HE TRIED TO DO WITH IT.
BUT BECAUSE IT WAS STUCK/DEAD , HE GAVE TO ME FOR CHEAP.
NOW THIS PHONE IS UNDER WARRANTY TILL AUG-2012 AND IS FROM VODAFONE.
(EVEN AFTER INSTALLING ANDROID IT IS VOID)
HE MUST HAVE TRIED SEVERAL ROM/HSPL TO GET TO THIS POINT.
Click to expand...
Click to collapse
Sir, you have forgotten your caps locked.
boxboy said:
PROBLEM:
When I power up the phone, it displays a NRG LOGO SCREEN (energize software), and it gets stuck on it forever.
When I do hold the volume down + power button, then it comes up with the three colour screen and it says SPL-2.08.0000, AND also says rom update failed (only if i try to install and then start up)
Click to expand...
Click to collapse
Because you have stock SPL, you won't be able to install any custom ROM or any stock ROM not made for your region/SN.
boxboy said:
The phone does connect through USB when it is on the three colour screen, but it does not let me install ANY OF THE romS or the spl'S...
I have tried literally every single step possible. I have tried to do task 29, i have tried install the original rom, i have tried to put the rom in the sd card and try it that way.. I have also tried to do hard reset... vol up and down and it does not complete either..
Click to expand...
Click to collapse
AFAIK, task29 is, also to be considered, a custom rom so it needs HSPL to be flashed. Are you sure you have followed the steps correctly?
boxboy said:
I best rom it let me install was 99% of 2.10.50.19.2.. but after 99% it got stuck .. it seems like it gets stuck within 1 min or so.. anything you do!
Some times after several hundred attempts, it does let me change the spl... as it was displaying 3.... before then i changed to 1.4..... and then to 2.08...
Click to expand...
Click to collapse
That is not a ROM, it's a radio. You need to flash HSPL to be able to change the splash screen (NRG Screen). HSPL should go like this: SPL 2.08.HSPL .
boxboy said:
All i want to do is to get rid of the NRG SCREEN, so i could send to the htc ,, for repair ( i know that it is not under warranty if i used andriod, but they will not know) .. or is there any way to completely format the phone,,, is there any solution to install andriod or microsoft? pls help
Click to expand...
Click to collapse
Microsoft is a corporation, Windows Phone is the OS .
One more thing, to be able to flash a LEOIMG from sd, the .nbh must be a rom that is compatible with your device (It will work if you get it from htc.com using the device's serial number)
I hope this helps. And I'm sorry if I am incorrect at something.
Good luck.
------------------------------------------------------------------------------------------------------------------------------------------------
To summarize it, you need to do either one of the following:
1- Install HSPL, and do what you want.
2- Go to HTC.com, download a rom using your Serial Number, rename file to .zip, extract the .nbh file, rename to LEOIMG.NBH [Capital letters], put onto sd card and insert into phone, boot up device while holding volume down ONLY, and make sure splash is removed and you're back to the "htc" stock, then send to repair [why?].

posting teh same post in multiple sub forums is considered rude
http://forum.xda-developers.com/showthread.php?t=1440265

Yeah, HSPL is needed for flashing pretty much everything. One thing you could do would be to flash a stock ROM from your SD card (just google it I CBA to provide links and stuff) which would reset everything to factory WinMo (including SPL to SPL3.03 [assuming you flash the latest ROM 3.14]) and from here it would basically be a fresh start. Probably the safest route without HSPL

Hi.
Thank you for your replies...
Let me tell u guys if I forgot to say earlier. The mobile phone is not letting flash any of the Hspl... be q series, 2 series or 3.series... all the times it says error 0000006 and 000000010 etc... a couple out of hundreds it did let flash but then it doesn't let me flash the factory rom fom HTC.

I have succesfuly flashed the 3.03 hspl... bit still no success in flashing any roms ... it gets stuck sometimes at 99% and sometimes at 0% and sometimes it comes up with a scrambled screen and stuck

OK,
My final.outcome.
This phone let's me flash the hspl but it doesn't let me flush any roms including the original HTC factory rom.
I can also perform the task 29. Etc but still the NRG screen is still there.
I would like to know that if I flash the original Split and send it HTC, will be repairable for free? Sure? Even with the NRG.

now i think the only option available to you is jtagging the device which may permanently void the warranty !!
it had happened with me once, but somehow it got solved !
i used to randomly install clk, magldr, radios, hspl etc multiple times !
it used to get stuck while installing and then i used to remove the battery and try again !!
somehow it started ! !!
STRANGE DEVICE !!

Yeap its a real problem!!
Now , It will not let me change the hspl to spl whatsoever I do.
I would like your suggestions
I bought this brick for £50 and I can return it to get my money back. Has any used jtagging and does it 100% work?. The thing is if I do used jtagging, and if it doesn't work ,then I can,t return it!. How much does it cost and is it worth it?

jtagging will solve your problem !!
they remove the motherboard of the device and flash the os into the motherboard directly through a device named riff box !!
refer this video for more info !!
http://www.youtube.com/watch?v=zElsUERTzOU
but pls do not try this at home ! !!
just contact a local repair shop to jtag your device !!
also u can contact these guys from the video !!
good luck ! !!

boxboy said:
I have succesfuly flashed the 3.03 hspl... bit still no success in flashing any roms ... it gets stuck sometimes at 99% and sometimes at 0% and sometimes it comes up with a scrambled screen and stuck
Click to expand...
Click to collapse
Check that the micro USB connection isn't "wobbly".
I had a TMOUS HD2 and never had any issues. Then, I sold it and got a Telstra HD2 and had big issues getting ROMs installed until I realized that the connection at the phone was a little weak. I can't send any updates to WP7 via cab sender unless the phone is in a certain position to keep the connection from breaking.

boxboy said:
I bought an HTC HD2 FEW WEEKS BACK FROM ONE OF MY FRIEND.
I DO NOT HAVE THE HISTORY OF WHAT HE TRIED TO DO WITH IT.
BUT BECAUSE IT WAS STUCK/DEAD , HE GAVE TO ME FOR CHEAP.
NOW THIS PHONE IS UNDER WARRANTY TILL AUG-2012 AND IS FROM VODAFONE.
(EVEN AFTER INSTALLING ANDROID IT IS VOID)
HE MUST HAVE TRIED SEVERAL ROM/HSPL TO GET TO THIS POINT.
PROBLEM:
When I power up the phone, it displays a NRG LOGO SCREEN (energize software), and it gets stuck on it forever.
When I do hold the volume down + power button, then it comes up with the three colour screen and it says SPL-2.08.0000, AND also says rom update failed (only if i try to install and then start up)
The phone does connect through USB when it is on the three colour screen, but it does not let me install ANY OF THE romS or the spl'S...
I have tried literally every single step possible. I have tried to do task 29, i have tried install the original rom, i have tried to put the rom in the sd card and try it that way.. I have also tried to do hard reset... vol up and down and it does not complete either..
I best rom it let me install was 99% of 2.10.50.19.2.. but after 99% it got stuck .. it seems like it gets stuck within 1 min or so.. anything you do!
Some times after several hundred attempts, it does let me change the spl... as it was displaying 3.... before then i changed to 1.4..... and then to 2.08...
All i want to do is to get rid of the NRG SCREEN, so i could send to the htc ,, for repair ( i know that it is not under warranty if i used andriod, but they will not know) .. or is there any way to completely format the phone,,, is there any solution to install andriod or microsoft? pls help
Click to expand...
Click to collapse
Don't worry ... you can give the life to your phone back... it shows fail bcus u have 2.08.0000.. so it means u Sud have 2.08 v hspl.. so try flashing hspl by getting into bootloader(3 colour) by pressing volume down + power Then flash hspl.. but remember select 2.08v.. then again after flashing hold volume down + power.. bootlooder.. then flash magdlr 1.13 ... now the phone will boot into a black screen with written mangdlr.. wen the black screen magdlr screen comes then press power off for 5mintzz.. follow the guide to flash.. there is a stick thread in NAND DEVELOP... U can get the windows version back to your phone to get the warranty...
Sent from my HTC HD2 using Tapatalk

Ok ,, some good new at last ..
I have used the HSPL4 to change my 3.03hspl to 3.030000 spl...
Success, as when i go to the tri colour screen it says spl and no hint of hspl...
Bad news, is that i still cant get the rom flashing,, as it gets stuff at some point and mostly at 99%.. Have tried both ways through SD (leoimg) and through USB.
Now final question is ... When i on the phone a big logo of NRG (ENERGIZE) writtten comes up and it gets stuck there.. the phone has SPL .. so it still under warranty to return it?.. I still have all the void sticker intact.

boxboy said:
Now final question is ... When i on the phone a big logo of NRG (ENERGIZE) writtten comes up and it gets stuck there.. the phone has SPL .. so it still under warranty to return it?.. I still have all the void sticker intact.
Click to expand...
Click to collapse
did you try to flash just a splashscreen as i suggested in your other thread? (they can be flashed alone, no need for a whole rom, , just like radios)
if you can get a stock splashscreen on there you are sorted.

Maybe try to download the original Software from HTC.
With you serial number you can get the latest windows for this phone.
Flash the Software you get from HTC.
If this is working ok you can try to install any Android ROM.
Read at first this
http://forum.xda-developers.com/showthread.php?t=905841
Try to understand and follow the steps..
But if you have even no luck with original Windows soft. You will also (maybe) have a lot of probs. with Android..

Thank you guys for all your help..
I have flashed andriod on several phones some time ago and I actually forgot the right steps to follow.
But this phone is unique is not letting me finish.
After following all the right steps, i wasnt able to install a rom succesfully even after installing the HSPL... and I am also not able to install the factory rom from htc on either the hspl or spl settings.
But i now got rid of the NRG screen and I have also installed the spl 3.03.. When you on the phone, it displays software upgrade failed..
So I have now sent the mobile to HTC as it is under warranty. I will then re-flash andriod following the right steps and see what happens!
Thanks again!

My mobile came back from HTC with a week.. Looks like a brand new one!
In the letter it says the replaced IMEI, PCBA, FL BD, W/O_ REGIONAL_ID, LEO
WOW
GREAT PHONE... ITS MUCH FASTER THAN THE PREVIOUS ONE FOR SOME REASONS