Any advise or help would be appreciated. My hd2 will not boot. Gets stuck on the the white htc screen. Tried flashing standard rom and Android. They all say succesful then when I boot it stops. Even tried loading it from the SD
Even stuck it into the local phone shop, took a week to tell me its f*** not sure if they knew what they were doing.
Anybody know anywhere that specialises in them.
did u check ur hspl??
Hi, I have reurned it back to stock by flashing the std rom.
Then flashed HSPL. MAGDLR and radio, still no joy.
Then flashed back the standard rom. Still the HTC screen
husky_motox said:
Hi, I have reurned it back to stock by flashing the std rom.
Then flashed HSPL. MAGDLR and radio, still no joy.
Then flashed back the standard rom. Still the HTC screen
Click to expand...
Click to collapse
Do you happen to know what radio you have? As what you are experiencing is sometimes called a stuck radio. Also has your HD2 been getting warmer thaan usual?
its not bricked. people really should learn that term, a bricked phone wont turn on
Richy99 said:
its not bricked. people really should learn that term, a bricked phone wont turn on
Click to expand...
Click to collapse
I agree the word bricked gets used way too much here. If the phone will turn on and start to boot up or if you can still access the default multicolor bootloader the HD2 is not bricked and in all likely hood can be fixed via software adjustments. If the HD2 will not give you access to the multicolor bootloader then it is bricked and will need a JTAG or the mainboard replaced.
I have got to admit though it has been a rash of people posting here for the last month or so with the exact problem the OP has of the HD2 getting stuck at the HTC screen. Some or a result of thermal breakdown of the connections between the CPU and the main board, but these people should know this is their problem as their HD2 will get very warm or hot to the touch around the area of the mainboard.
Hey guys I have a hd2 that wont boot up anymore. I have installed several windows 6.5 cooked roms into this device for a while now. Recently this device has been given me a lot of problems until finally it took a dump. Now everytime i power up the device it stays in the splash screen. It doesnt even show radio version, rom version,etc on the bottom left of the screen. So is this hd2 dead or is there some way that i can fix it. I even tried installing tmobile's official rom on this device by going into the "rainbow screen" so that the device can be seen by using the usb cable, but alas....it didnt work either. So any help would be appreciated .
If it doesn't install, and nothing installs, then you need to take it to repair I guess.
I had a feeling about that. I just figured there was no way to fix it and the fact that i couldnt send it back to tmobile to get a replacement was out of the question since the firmware was modified. But your saying there are shops that fix these kinds of issues? If so, I better start looking around over here.
frequency1 said:
I had a feeling about that. I just figured there was no way to fix it and the fact that i couldnt send it back to tmobile to get a replacement was out of the question since the firmware was modified. But your saying there are shops that fix these kinds of issues? If so, I better start looking around over here.
Click to expand...
Click to collapse
why dont you try sd card method for flashing your rom !1! you can pm me if you need further help
Do you mean that it can't get to the boot loader screen (rainbow) or that trying to install a ROM from there didn't work? You might want to flash the original HSPL too, just to check.
What I mean is that everytime I boot up the hd2 it stays stuck on the splash screen. It doesn't even show the rom information in red at the bottom left corner of the screen. But I can boot to the tri color menu though. I have tried to install the tmous official rom by plugging the USB when I'm in the tri color menu and it always stays stuck at 9%. So is there way to fix this or am I screwed.
Sent from my Android Powered HD2 using XDA App
Try the sd-card recovery instead of the USB one.
http://www.jayceooi.com/2011/01/01/how-to-upgrade-htc-hd2-rom-through-sd-card-video/
After that, even if it fails, it shows only SPL in the tri-color screen then you are set to claim warranty.
frequency1 said:
Hey guys I have a hd2 that wont boot up anymore. I have installed several windows 6.5 cooked roms into this device for a while now. Recently this device has been given me a lot of problems until finally it took a dump. Now everytime i power up the device it stays in the splash screen. It doesnt even show radio version, rom version,etc on the bottom left of the screen. So is this hd2 dead or is there some way that i can fix it. I even tried installing tmobile's official rom on this device by going into the "rainbow screen" so that the device can be seen by using the usb cable, but alas....it didnt work either. So any help would be appreciated .
Click to expand...
Click to collapse
Well my bro... i think thats nand problems or heating issues ... does flashing rom goes all ok or it stops during flashing ? if stops than check if you phone is hot - hotter than normal.
Try this : Take out battery, memory card, sim card and put you phone in the fridge for about 5-10 min ( dont worry tried many times... no harm ) meanwhile prepare your sd card to flash rom with sd card method ... to do that extract Ruu rom - stock one - download with hd2 serial nr ( winrar, 7zip etc) find Ruu_Signed.nbh rename it to LEOIMG.nbh than copy to sd card ( format you sd card fat32 and make sure it works ... 2gb will work ) take phone out from fridge put sd card & battery into phone power one phone while holding volume down key ( go into tricolor screen - bootloader) and follow procedure in phone... i hope everything goes well and you fix you phone... but if still no success than flash android or wp7 ( if you have warranty flash stock SPL and return phone).
best regards from me
Hi,
i`ve got a problem with my touchscreen, after installing SD card distribution of Android, few restarts later my touchscreen stpped to respond every time when my device is locked, and i have to restart it.
I tried to flash new rom - nothing happend
H-E-L-P !
remove sd card delete the partitions and format - use Easeus free edition for this
Then boot the phone - reun task 29 from your pc then reread the flashing instructions for the rom of your choice and try again - ensure the rom supports your version og HD2 whatever that may be
All done, and doesn`t work. I`m wonderig if is possible, that is malfunction of touchscreen, because it have been changed after it was broken.
i'm having the same issue. after it goes into its first lock screen the touch screen input doesn't work. i've flashed the ROM and also task29 the sucker. i've reverted back to stock ROM too. I'm not running android or even try to install from SD.
Bump..!
Anybody got a solution for this..?
I have a HD2 with android on it.. nand version.. so it runs without sd card..
The phone works fine.. but when you lock it.. the screen doesnt respond anymore.. its running miui at the moment, so i can unlock the lockscreen.. but still the screen doesnt respond..
i see more people having this issues, so i hope to find a solution..
keep on searching..!
So Am I
after 5 moths of Android Nand use I have the same problem. I have changed kernel/ROM
I made few times task29 wipe cache/dalvik but still the same
Yesterday I try install the orginal WWE 6.5 ROM but nothing change...
Maybe is hardware issue ? Few times with android rom my leo was very hot and maybe something burn inside ? or its stupid idea but who knows
gomez.pl said:
So Am I
after 5 moths of Android Nand use I have the same problem. I have changed kernel/ROM
I made few times task29 wipe cache/dalvik but still the same
Yesterday I try install the orginal WWE 6.5 ROM but nothing change...
Maybe is hardware issue ? Few times with android rom my leo was very hot and maybe something burn inside ? or its stupid idea but who knows
Click to expand...
Click to collapse
Sure it's hardware: replacing touchscreen is your best choice!
But is this because of android on hd2? or do other people with stock phones also see this problem?
Hd2 is already gone here.. but i think its a good thing to know for the scene..
thommy86 said:
But is this because of android on hd2? or do other people with stock phones also see this problem?
Hd2 is already gone here.. but i think its a good thing to know for the scene..
Click to expand...
Click to collapse
It's a wellknown (hardware) problem for HD2, not related to software(android/wm/wp/whatever).
SO my LEO came back from service, there is a part list that they changed:
- 54h20178-00M pre-assy key, key FPC, UF-KS, w/o Reg
- 74H01549-00M Chassis Pre-assy, black, stainless steel, MLRB81
- 76H04078-00M tape, FPC connector, kapton, MLRB81
- 83H00294-01 change 83H00233-01, 83H00294-03, 62H00065-B1M Sub-assy to 82H
maybe You need do the same...
Okay, so i just bought my 6th HD2, and this one got the lockscreen problem as well. If i lock the screen using the red power button and try to wake it up with the same red power button i found out that it doesn't work. I tried everything but i think i found a sort of workaround for the touchscreen problem.
1. Lock the screen as you normally do, with the red power button.
2. Wait at least more then 6 seconds with the screen off.
3. Now push the VOLUME UP button to make the device wake up.
4. Profit!
5. If it doesn't work, go back to 1 and try again.
I found out that if it works 1 time it will work multiple times in a row.
I'm on NAND but i think it works on SD aswell.
Please post your reactions to this.
I bought an HTC HD2 FEW WEEKS BACK FROM ONE OF MY FRIEND.
I DO NOT HAVE THE HISTORY OF WHAT HE TRIED TO DO WITH IT.
BUT BECAUSE IT WAS STUCK/DEAD , HE GAVE TO ME FOR CHEAP.
NOW THIS PHONE IS UNDER WARRANTY TILL AUG-2012 AND IS FROM VODAFONE.
(EVEN AFTER INSTALLING ANDROID IT IS VOID)
HE MUST HAVE TRIED SEVERAL ROM/HSPL TO GET TO THIS POINT.
PROBLEM:
When I power up the phone, it displays a NRG LOGO SCREEN (energize software), and it gets stuck on it forever.
When I do hold the volume down + power button, then it comes up with the three colour screen and it says SPL-2.08.0000, AND also says rom update failed (only if i try to install and then start up)
The phone does connect through USB when it is on the three colour screen, but it does not let me install ANY OF THE romS or the spl'S...
I have tried literally every single step possible. I have tried to do task 29, i have tried install the original rom, i have tried to put the rom in the sd card and try it that way.. I have also tried to do hard reset... vol up and down and it does not complete either..
I best rom it let me install was 99% of 2.10.50.19.2.. but after 99% it got stuck .. it seems like it gets stuck within 1 min or so.. anything you do!
Some times after several hundred attempts, it does let me change the spl... as it was displaying 3.... before then i changed to 1.4..... and then to 2.08...
All i want to do is to get rid of the NRG SCREEN, so i could send to the htc ,, for repair ( i know that it is not under warranty if i used andriod, but they will not know) .. or is there any way to completely format the phone,,, is there any solution to install andriod or microsoft? pls help
Before we start, you can ask him how his device has ended up like this, can't you?
boxboy said:
I bought an HTC HD2 FEW WEEKS BACK FROM ONE OF MY FRIEND.
I DO NOT HAVE THE HISTORY OF WHAT HE TRIED TO DO WITH IT.
BUT BECAUSE IT WAS STUCK/DEAD , HE GAVE TO ME FOR CHEAP.
NOW THIS PHONE IS UNDER WARRANTY TILL AUG-2012 AND IS FROM VODAFONE.
(EVEN AFTER INSTALLING ANDROID IT IS VOID)
HE MUST HAVE TRIED SEVERAL ROM/HSPL TO GET TO THIS POINT.
Click to expand...
Click to collapse
Sir, you have forgotten your caps locked.
boxboy said:
PROBLEM:
When I power up the phone, it displays a NRG LOGO SCREEN (energize software), and it gets stuck on it forever.
When I do hold the volume down + power button, then it comes up with the three colour screen and it says SPL-2.08.0000, AND also says rom update failed (only if i try to install and then start up)
Click to expand...
Click to collapse
Because you have stock SPL, you won't be able to install any custom ROM or any stock ROM not made for your region/SN.
boxboy said:
The phone does connect through USB when it is on the three colour screen, but it does not let me install ANY OF THE romS or the spl'S...
I have tried literally every single step possible. I have tried to do task 29, i have tried install the original rom, i have tried to put the rom in the sd card and try it that way.. I have also tried to do hard reset... vol up and down and it does not complete either..
Click to expand...
Click to collapse
AFAIK, task29 is, also to be considered, a custom rom so it needs HSPL to be flashed. Are you sure you have followed the steps correctly?
boxboy said:
I best rom it let me install was 99% of 2.10.50.19.2.. but after 99% it got stuck .. it seems like it gets stuck within 1 min or so.. anything you do!
Some times after several hundred attempts, it does let me change the spl... as it was displaying 3.... before then i changed to 1.4..... and then to 2.08...
Click to expand...
Click to collapse
That is not a ROM, it's a radio. You need to flash HSPL to be able to change the splash screen (NRG Screen). HSPL should go like this: SPL 2.08.HSPL .
boxboy said:
All i want to do is to get rid of the NRG SCREEN, so i could send to the htc ,, for repair ( i know that it is not under warranty if i used andriod, but they will not know) .. or is there any way to completely format the phone,,, is there any solution to install andriod or microsoft? pls help
Click to expand...
Click to collapse
Microsoft is a corporation, Windows Phone is the OS .
One more thing, to be able to flash a LEOIMG from sd, the .nbh must be a rom that is compatible with your device (It will work if you get it from htc.com using the device's serial number)
I hope this helps. And I'm sorry if I am incorrect at something.
Good luck.
------------------------------------------------------------------------------------------------------------------------------------------------
To summarize it, you need to do either one of the following:
1- Install HSPL, and do what you want.
2- Go to HTC.com, download a rom using your Serial Number, rename file to .zip, extract the .nbh file, rename to LEOIMG.NBH [Capital letters], put onto sd card and insert into phone, boot up device while holding volume down ONLY, and make sure splash is removed and you're back to the "htc" stock, then send to repair [why?].
posting teh same post in multiple sub forums is considered rude
http://forum.xda-developers.com/showthread.php?t=1440265
Yeah, HSPL is needed for flashing pretty much everything. One thing you could do would be to flash a stock ROM from your SD card (just google it I CBA to provide links and stuff) which would reset everything to factory WinMo (including SPL to SPL3.03 [assuming you flash the latest ROM 3.14]) and from here it would basically be a fresh start. Probably the safest route without HSPL
Hi.
Thank you for your replies...
Let me tell u guys if I forgot to say earlier. The mobile phone is not letting flash any of the Hspl... be q series, 2 series or 3.series... all the times it says error 0000006 and 000000010 etc... a couple out of hundreds it did let flash but then it doesn't let me flash the factory rom fom HTC.
I have succesfuly flashed the 3.03 hspl... bit still no success in flashing any roms ... it gets stuck sometimes at 99% and sometimes at 0% and sometimes it comes up with a scrambled screen and stuck
OK,
My final.outcome.
This phone let's me flash the hspl but it doesn't let me flush any roms including the original HTC factory rom.
I can also perform the task 29. Etc but still the NRG screen is still there.
I would like to know that if I flash the original Split and send it HTC, will be repairable for free? Sure? Even with the NRG.
now i think the only option available to you is jtagging the device which may permanently void the warranty !!
it had happened with me once, but somehow it got solved !
i used to randomly install clk, magldr, radios, hspl etc multiple times !
it used to get stuck while installing and then i used to remove the battery and try again !!
somehow it started ! !!
STRANGE DEVICE !!
Yeap its a real problem!!
Now , It will not let me change the hspl to spl whatsoever I do.
I would like your suggestions
I bought this brick for £50 and I can return it to get my money back. Has any used jtagging and does it 100% work?. The thing is if I do used jtagging, and if it doesn't work ,then I can,t return it!. How much does it cost and is it worth it?
jtagging will solve your problem !!
they remove the motherboard of the device and flash the os into the motherboard directly through a device named riff box !!
refer this video for more info !!
http://www.youtube.com/watch?v=zElsUERTzOU
but pls do not try this at home ! !!
just contact a local repair shop to jtag your device !!
also u can contact these guys from the video !!
good luck ! !!
boxboy said:
I have succesfuly flashed the 3.03 hspl... bit still no success in flashing any roms ... it gets stuck sometimes at 99% and sometimes at 0% and sometimes it comes up with a scrambled screen and stuck
Click to expand...
Click to collapse
Check that the micro USB connection isn't "wobbly".
I had a TMOUS HD2 and never had any issues. Then, I sold it and got a Telstra HD2 and had big issues getting ROMs installed until I realized that the connection at the phone was a little weak. I can't send any updates to WP7 via cab sender unless the phone is in a certain position to keep the connection from breaking.
boxboy said:
I bought an HTC HD2 FEW WEEKS BACK FROM ONE OF MY FRIEND.
I DO NOT HAVE THE HISTORY OF WHAT HE TRIED TO DO WITH IT.
BUT BECAUSE IT WAS STUCK/DEAD , HE GAVE TO ME FOR CHEAP.
NOW THIS PHONE IS UNDER WARRANTY TILL AUG-2012 AND IS FROM VODAFONE.
(EVEN AFTER INSTALLING ANDROID IT IS VOID)
HE MUST HAVE TRIED SEVERAL ROM/HSPL TO GET TO THIS POINT.
PROBLEM:
When I power up the phone, it displays a NRG LOGO SCREEN (energize software), and it gets stuck on it forever.
When I do hold the volume down + power button, then it comes up with the three colour screen and it says SPL-2.08.0000, AND also says rom update failed (only if i try to install and then start up)
The phone does connect through USB when it is on the three colour screen, but it does not let me install ANY OF THE romS or the spl'S...
I have tried literally every single step possible. I have tried to do task 29, i have tried install the original rom, i have tried to put the rom in the sd card and try it that way.. I have also tried to do hard reset... vol up and down and it does not complete either..
I best rom it let me install was 99% of 2.10.50.19.2.. but after 99% it got stuck .. it seems like it gets stuck within 1 min or so.. anything you do!
Some times after several hundred attempts, it does let me change the spl... as it was displaying 3.... before then i changed to 1.4..... and then to 2.08...
All i want to do is to get rid of the NRG SCREEN, so i could send to the htc ,, for repair ( i know that it is not under warranty if i used andriod, but they will not know) .. or is there any way to completely format the phone,,, is there any solution to install andriod or microsoft? pls help
Click to expand...
Click to collapse
Don't worry ... you can give the life to your phone back... it shows fail bcus u have 2.08.0000.. so it means u Sud have 2.08 v hspl.. so try flashing hspl by getting into bootloader(3 colour) by pressing volume down + power Then flash hspl.. but remember select 2.08v.. then again after flashing hold volume down + power.. bootlooder.. then flash magdlr 1.13 ... now the phone will boot into a black screen with written mangdlr.. wen the black screen magdlr screen comes then press power off for 5mintzz.. follow the guide to flash.. there is a stick thread in NAND DEVELOP... U can get the windows version back to your phone to get the warranty...
Sent from my HTC HD2 using Tapatalk
Ok ,, some good new at last ..
I have used the HSPL4 to change my 3.03hspl to 3.030000 spl...
Success, as when i go to the tri colour screen it says spl and no hint of hspl...
Bad news, is that i still cant get the rom flashing,, as it gets stuff at some point and mostly at 99%.. Have tried both ways through SD (leoimg) and through USB.
Now final question is ... When i on the phone a big logo of NRG (ENERGIZE) writtten comes up and it gets stuck there.. the phone has SPL .. so it still under warranty to return it?.. I still have all the void sticker intact.
boxboy said:
Now final question is ... When i on the phone a big logo of NRG (ENERGIZE) writtten comes up and it gets stuck there.. the phone has SPL .. so it still under warranty to return it?.. I still have all the void sticker intact.
Click to expand...
Click to collapse
did you try to flash just a splashscreen as i suggested in your other thread? (they can be flashed alone, no need for a whole rom, , just like radios)
if you can get a stock splashscreen on there you are sorted.
Maybe try to download the original Software from HTC.
With you serial number you can get the latest windows for this phone.
Flash the Software you get from HTC.
If this is working ok you can try to install any Android ROM.
Read at first this
http://forum.xda-developers.com/showthread.php?t=905841
Try to understand and follow the steps..
But if you have even no luck with original Windows soft. You will also (maybe) have a lot of probs. with Android..
Thank you guys for all your help..
I have flashed andriod on several phones some time ago and I actually forgot the right steps to follow.
But this phone is unique is not letting me finish.
After following all the right steps, i wasnt able to install a rom succesfully even after installing the HSPL... and I am also not able to install the factory rom from htc on either the hspl or spl settings.
But i now got rid of the NRG screen and I have also installed the spl 3.03.. When you on the phone, it displays software upgrade failed..
So I have now sent the mobile to HTC as it is under warranty. I will then re-flash andriod following the right steps and see what happens!
Thanks again!
My mobile came back from HTC with a week.. Looks like a brand new one!
In the letter it says the replaced IMEI, PCBA, FL BD, W/O_ REGIONAL_ID, LEO
WOW
GREAT PHONE... ITS MUCH FASTER THAN THE PREVIOUS ONE FOR SOME REASONS
Hello. My HD2 after about 2 years of working perfectly started to reset itself. Back then it was working on WM 6.5. The reseting problem started to appear more frequently then after one of those my screen went white(without any writing on it). I managed to turn it on with few battery out/soft/hard reset. All that gone in vain because it worked about 30 minutes then after reset gone back to previous state. Then i flashed original ROM but it didn't changed anything. After that I i installed android(nand) which worked fine for couple hours afterwards I saw familiar white screen. This time i couldn't flash rom from comp not even sd card. Task 29 stopped on 0%. In bootloader it seemed that I there was hspl 2.08. Then after keeping hd2 in freezer for about 30 minutes I managed to flash original ROM. However it still stopped on white screen but after instaling hspl 2.08 again i could use task29 then radio, maglar and recovery so i put it up for android again which worked for few hours again then it went white. That's it present state.
I've done some reading and it seems like i need to replace mainboard Plz tell me i'm wrong and there is still sth I could do. Beside of instaling android every few hours I'm sorry for my english. It's my first post so give me some slack.
your mainboard diagnosis seems correct.
either strip it for spares to help fund a replacement or find a mainboard for repair.
Mister B said:
your mainboard diagnosis seems correct.
either strip it for spares to help fund a replacement or find a mainboard for repair.
Click to expand...
Click to collapse
Unfortunately for you(OP) it seems the only way out of this...