I need help. I wanted to install android on htc hd2, i previously had WM 6.5. I formated sd card and put Android rom folder on it...run clrcad.exe and haret.exe. It came to black screen with some text, last line was something about jumping to kernel. It was there like 15 min, i pulled the battery...now it wont start...what to do?
When i plug in the usb it boots up to htc screen and then again shuts and boots to htc screen and keeps going like that.
Bent battery pin.
i now have another problem, i installed magldr 1.13 and now its stuck on htc logo screen...only can pull out battery and go to bootloader...i had radio 2.xx.50.xx...all the text on bootloader is:
PB81100 HX-BC
SPL-2.08.HSPL 8G XE
0x05
CotullaHSPL 0x30
what to do??
Go to tricolor screen. Install stock winmo ROM and make sure the phone boots up fine, etc. Then you can start messing with it again. Note - if you install a stock rom, your hard spl will be replaced.
Did you check the bent battery pin idea? And also, may want to try the thing stated above, but use a custom ROM.
Oh, and may seem obvious but you are holding the power button down when trying to boot MAGLDR right?
Related
My hd2 loops in startscreen, htc appears, then the rom and radioinformation down left and then it restarts and again and again, but only with synccable, with only battery it is dead. Nothing happens.
Now i´m able do get the bootloaderscreen (rgb and white) and usb-connection and flash everything I want, with the same result as above.
I flashed stock rom, originally o2-rom, radio-rom only a.s.o., same result, htc-screen with radio and thats it, restart.
Is there anything i can try before sending it back to htc?
The bootscreen says:
PB81100 HX-BC
SPL-1.42.HSPL XE
0x05
CotullaHSPL 0x30
so HSPL is installed, and usb connection works.
The explanation why i got this problem depends on voice command, i´ll tried to change some files, because the speech was too fast to heare it.
Is there anything that i can flash, thats really helps?
The next problem is, that i can´t boot the orinal rom from sd-card, because without cable nothing happens, and with cable thres is only usb to flash.
Nobody there with some instruments that may be only technicans use? Clean the complete ram and rom and what else is there? Or is it a real hardwareroblem that can´t be fixed?
if you have hspl you could flash a ROM using customRUU from the bootloader i think. Have you tried a hardreset (hold volume up and down and reset button)? i had the same problem but for me switching the phone off for a few hours (i didn't have access to a pc) it booted up and i flashed a stock ROM. its a bad rom flash thats the problem. once and if you can get it booted be sure to follow the instructions on the mtty thread or flash a stock ROM before each and every custom one.
EDIT : Haven't read it properly. seems worse than my problem. simple thing are you battery contacts good and making a proper connection? Only other thing i can think.
netfan55 said:
...
Now i´m able do get the bootloaderscreen (rgb and white) and usb-connection
...
The bootscreen says:
PB81100 HX-BC
SPL-1.42.HSPL XE
0x05
CotullaHSPL 0x30
so HSPL is installed, and usb connection works.
Click to expand...
Click to collapse
Try MTTY with your device.
is a battery problem?
excuse for my poor english....
I think that if you can not flash your HTC HD2, I think the problem is in the battery.
If the battery is discharged below 50% you are not allowed to flash.
Instead if you start flashing when the battery is above 50% but during the operation the battery falls below this threshold, the flashing operation stops generating an error (usually error 220). This is due to the fact that the device is not recharged during the upgrade radio.
with best regards, paperinapap
Hi all ^^
I'm new here, and I just received my HD2 and wanted to flash it with one of the cool ROMs you have on this forum.
I flashed the HSPL with HSPL2 and everything went smoothly. Then I downloaded one of CleanEX DSE Core Rom (the 6.5 Maniless FRE) to be precise.
I flashed it, all was good, at the end the phone rebooted and i was stuck at the boot screen written "HTC CleanEX UDT DsE Series". I thought maybe it was because I didn't do a hard reset yet. So i did one, everything initialyze and when it's done same thing, the phone reboot and I'm stuck at the same boot screen...
I'm starting to get a bit stressed out because if I can't connect to Activesync I can't even put an original Rom or an other twinked one ><
Does anybody know what I did wrong or why it's not working ?
Thanks in advance for your answers.
PS: My phone is a french phone.
radio - go back and reread that roms thread for recommendation, however 2.07.50.x or higher should do it.
boot to bootloader, connect usb, flash radio, phone will now boot
Connect your phone to PC and turn it on while holding volume down, bootloader menu should apear (red,green,blue,white) then you can run Rom flashing tool on your PC
but i recomend flashing newer RADIO because this may be the reason for your current issue.
That was a really quick and effective answer !!
Thanks a lot to both of you !!!! *hugs*
its seriously the radio
DN41
I tried to install HSPL but unfotunately it stops & my phone is not working. My HD2 hangs when HTC logo comes. I also try to copy stock ROM in SD card whilst pressing voldown & power keys, tricolour screen appeared & says:
PB81100 HX-BC
SPL-2.08.HSPL 8G XE
0x05
CotullaHSPL 0x40
Then the phone hangs.
Could anyone tell me what is ROM flashing tool & what version should I install.
Please help me.
smrazi said:
I tried to install HSPL but unfotunately it stops & my phone is not working. My HD2 hangs when HTC logo comes. I also try to copy stock ROM in SD card whilst pressing voldown & power keys, tricolour screen appeared & says:
PB81100 HX-BC
SPL-2.08.HSPL 8G XE
0x05
CotullaHSPL 0x40
Then the phone hangs.
Could anyone tell me what is ROM flashing tool & what version should I install.
Please help me.
Click to expand...
Click to collapse
are you flashing the ROM on a different micro sd card? you cant use a 8GB or 16GB. Try a smaller card like a 1GB or 2GB.
also rename the stock ROM to LEOIMG.nbh.
put that ROM file on a smaller card and go into bootloader should come right up. worked for me when i had to re-install stock to return defective unit.
Hey guys,
I have a friend that has an HTC HD2 with an android rom on it:
SPL-1.42.HSPL XE 0x05
CotullaHSPL 0x30
It was working fine untill today when during a call it locked up and rebooted. However after the reboot it hangs on the white screen with the HTC logo.
We managed to get it to work again by removing the card, rebooting, then reinserting the card and booting after about 3mins the winmo booted. but when you try to boot into android it locks up again and just starts buzzing.
Anyone have any idea what's wrong and how to solve it?
Press volume (-) button and Power button to go to bootloader mode and you can flash 2.08hspl. Then flash MagldR 1.13 and install android again.
Or try to reset button on the back by remove battery cover you will see yellow button.
Thanks I'll give it a try and let you know how it goes.
My HTC HD2 doesn't pass the white-green HTC screen anymore. I am able to flash it (when I flashed HSPL it said We hacked it) but still not able to go through the HTC screen. I tried flashing an original WM6 ROM, but the device still hangs at the HTC screen...
Can anyone help me? Is my phone bricked?
bartjakobs said:
My HTC HD2 doesn't pass the white-green HTC screen anymore. I am able to flash it (when I flashed HSPL it said We hacked it) but still not able to go through the HTC screen. I tried flashing an original WM6 ROM, but the device still hangs at the HTC screen...
Can anyone help me? Is my phone bricked?
Click to expand...
Click to collapse
Hi,
Your phone is not bricked.
What are you trying to install?
What radio do you have installed?
Flashing an original WM ROM should be done via sd card and it will remove HSPL.
Please give more information.
I installed RUU_Leo_HTC_NLD_1.66.404.1_Radio_Signed_15.30.50.07U_2.06.51.07_Ship
(that didn't work, if I only install this one I get a black screen after the HTC screen)
The tricolorscreen says:
PB81100 HX-BC
SPL-2.08 HSP: 8G XE
0X05
CotullaHSP 0X50
I will try to flash the original rom via sd card, but that is where it started.. The last time I flashed it (I had WP7 and wanted to try WM6.x) it stopped working. I flashed it via sd card and the second time I tried (when it already had stopped) it was hanging at 'Loading...'.
Any ideas?
bartjakobs said:
I installed RUU_Leo_HTC_NLD_1.66.404.1_Radio_Signed_15.30.50.07U_2.06.51.07_Ship
(that didn't work, if I only install this one I get a black screen after the HTC screen)
The tricolorscreen says:
PB81100 HX-BC
SPL-2.08 HSP: 8G XE
0X05
CotullaHSP 0X50
I will try to flash the original rom via sd card, but that is where it started.. The last time I flashed it (I had WP7 and wanted to try WM6.x) it stopped working. I flashed it via sd card and the second time I tried (when it already had stopped) it was hanging at 'Loading...'.
Any ideas?
Click to expand...
Click to collapse
Hi,
I take it from the ROM you tried to install that you are in the Netherlands.
Did you get the serial number from your phone and feed it into HTC support site?
Go to HTC site>support>download>ROM upgrade and choose appropriate ROM upgrade for your phone
Change the .exe to .zip and
Extract with winrar or 7z the RUU_Leo_HTC_****************************_Ship.zip
find the larger *.nbh file and rename it to leoimg.nbh and place this file on an sd card that is 4gb or less
and reboot to bootloader (the one with 4 colors,hold volume down button until you see "SEARCHING")
follow the instructions from there.
If you had WM7 on your phone ,you should reformat your sd card to fat 32 before putting on the leoimg.nbh
Backup your data first.
I flashed the original nbh file (from HTC site with my serial number) via sd card. Now it hangs at a black screen after the HTC screen.
On the HTC screen, there now is this:
R 2.15.50.14
G 14.42.50.11U
D 3.14.04666
But after that, the screen goes black (first black lines, than black screen). The backlight stays on.
The colored screen now says this:
Pb81100 HX-BC
SPL-3.03.0000 XE
MicroP(LED) 0x05
MicroP(TOUCH) 0x50
What can I do now?
bartjakobs said:
I flashed the original nbh file (from HTC site with my serial number) via sd card. Now it hangs at a black screen after the HTC screen.
On the HTC screen, there now is this:
R 2.15.50.14
G 14.42.50.11U
D 3.14.04666
But after that, the screen goes black (first black lines, than black screen). The backlight stays on.
The colored screen now says this:
Pb81100 HX-BC
SPL-3.03.0000 XE
MicroP(LED) 0x05
MicroP(TOUCH) 0x50
What can I do now?
Click to expand...
Click to collapse
Hi,
I think the problem is the SPL-3.03.
Did you get a choice of original ROMS to download?
Try to get 1.43 and 1.48 roms that come with spl 1.42.0000
I tried flashing 1.48 EU English (RUU_Leo_HTC_WWE_1.48.405.2_Radio_Signed_15.28.50.07U_2.05.51.05_2_Ship)
It says
00028002
Not allowed
when starting. After this it goes back to tricolor screen
bartjakobs said:
I tried flashing 1.48 EU English (RUU_Leo_HTC_WWE_1.48.405.2_Radio_Signed_15.28.50.07U_2.05.51.05_2_Ship)
It says
00028002
Not allowed
when starting. After this it goes back to tricolor screen
Click to expand...
Click to collapse
Hi,
ROM code error usually means that official ROM is not for that HD2.
Other than that ,are you using 4GB or less sd card?
Is the phone charged to more than 50%?
I downloaded the original Dutch 1.48 rom
(RUU_Leo_HTC_NLD_1.48.404.2_Radio_Signed_15.28.50.07U_2.05.51.05_2_Ship)
from the HTC website and installed it via SD card.
Now the tricolor screen is:
PB81100 HX-BC
SPL-1.42.0000
etc.
When I start the phone, I see the HTC logo
A few seconds later this appears:
R 2.05.51.05^^^2
G 15.28.50.07U
D 1.48.71294
then, about a minute later, lines and a black screen.
Is there any hope?
bartjakobs said:
I downloaded the original Dutch 1.48 rom
(RUU_Leo_HTC_NLD_1.48.404.2_Radio_Signed_15.28.50.07U_2.05.51.05_2_Ship)
from the HTC website and installed it via SD card.
Now the tricolor screen is:
PB81100 HX-BC
SPL-1.42.0000
etc.
When I start the phone, I see the HTC logo
A few seconds later this appears:
R 2.05.51.05^^^2
G 15.28.50.07U
D 1.48.71294
then, about a minute later, lines and a black screen.
Is there any hope?
Click to expand...
Click to collapse
Try task29- it will erase rom in your hd2 ( it needs hspl )
or
You could try android or wp7 just to see if it works ( other than this i dont know what to say - sorry ).
I tried that (Android & WP7 won't work, because I can't get into MAGLDR. I do get it installed but I can't boot into it).
Tomorrow I'll try task 29.
Run Task 29 after flashing HSPL. This will clean out your system, then flash the 1.48 ROM by SD card method again.
Was there not a 1.66 Netherlands ROM version you could have downloaded?
thanks guys
I flashed HSPL and did task 29. After this, when I flashed the original rom, it stopped with an !.
The second time I tried installing the rom, it just installed but it doesn't start. Only lines and black screen.
during flashing procces does your phone gets hot ?
If yes thats hardware problem ( + software )... in this case to make sure try this:
Take out battery, simcard, sdcard and put it in a fridge for 5-10 min ( put phone in a bag to protect from watter), then take your phone and try to flash rom with sdcard method and post results.
The phone doesn't get hot. An update only fails the first time after a Task 29. The second update succeeds, but then it hangs at HTC or black screen.
I have same problem but not can fix it Many Thanks for all information.
Up new ROM via SD Card.
Okay, so I have been putting ROMs on my HTC HD2 problem is now i have is it says.
PB81120 HX-B3
SPL-2.08.HSPL 8G XE
0X05
COTULLAHSPL 0X40
Now what exactly do I do from here? I try to start normally but it just stays on "Stick Together" Screen. Help?
What was the last thing you did before it had stopped booting (stuck on "stick-together" screen lol) ?
It won't just stop booting for no reason.
check if you can still go to magloader...then re-flash the ROM, just follow thre requirements of the ROM before flashing
download hd2 toolkit, do a task29, and install magldr 1.3, then install wich rom you like
Here check out this guide I wrote. Basically your on step 8. Something has happened and you phone is wiped, but your still good.
This guide is for cLK and and CWM.
Hope this helps!
http://forum.xda-developers.com/showthread.php?t=1402975
If you do a t29 then the phone will be completely wiped of anything including MAGLDR and wm6.5 that would be why it just stays on the boot screen. The next step would be to boot the phone by holding the volume down button and power button until it boots into a tri-color (downloader) screen. Then you can flash MAGLDR and android
Okay so I fixed this problem. If you need to know send me a message.
Sent from my HTC HD2 using XDA App