Related
Hey, small problem here. I was charging my HD2 earlier today with no problems at all, I flashed the 1.72 stock ROM back onto my phone, and it seemed to be charging fine for a small while after that. But now, after I tried charging my phone, it doesn't seem to recognise there's a USB connection at all. The LED at the speaker-grille isn't doing anything, and the the phone tells me it isn't connected by USB when it's plugged into a computer.
I tried a tonne of things, checked the cable and switched it, soft-reset it, took the battery out, hard reset it, and even blown inside the socket to try and get rid of anything that might be blocking it, but it just isn't showing it's plugged in AT ALL any more... and now the battery is dead, so I can't do anything with it now to try and help it. :/
The only sign I have that the phone realises it has any sort of USB connection, is when I tried to hard reset the device, (I used the hold volUp+volDown+Power method) and it shows the message 'press volUp to hard reset,' usually when I do this, pressing volume up doesn't do anything when the phone is connected by USB for some weird reason - and I have to disconnect USB for the phone to hard reset. I figured this wouldn't happen if the phone doesn't realise it has a USB connection, but when the cable was plugged in, it still wouldn't hard reset until I took it out. So it shows there must be some way the phone knows it's connected.
I'm running the WWE 1.72 ROM with radio 2.10. 50.08_2 if it helps.
Any suggestions?
*Bump*
Sorry for the bump, but it would really help if anyone could help explain this.
I think a bit of trial and error would be best here to establish whats at fault.
phone, cable, or usb port.
-try plugging into a different usb port
-try a different cable (if you have one)
appologies if you have tried these allready.
Tried another cable again just incase, still nothing though. My iPods connected via that USB port I tried using, and that's working fine, so it doesn't seem like that's it, either...
Hi:
I'm having a similar problem. I had plugged in a new retractable usb cable, and when I did, the phone shut off. I rebooted, and tried my original cable, but the phone doesn't charge or sync. I've also tried hard/soft reset, wall charger, usb charger, and none of that seems to work.
Any suggestions?
Thanks.
No idea if this is related or not but my USB connection stopped working after I got the "bttrayce.exe is not a valid pocket pc application" problem (Thanks TomTom! ) so it would appear the USB port has some weird dependencies!
Fixed it by renaming the windows\btsdkce30.dll file (added "[temp]" to the name just in case!) and soft-resetting.
Might be worth a try?
r u using activsync or windows mobile centre ???
USB Issue
I've got exactly the same issue, running HyperROM 3.01.405.T1 and Radio 2.06.51.07.
Suddenly USB isn't working, tried various cables and I suspect it's a software issue somewhere.
Charging isn't a problem at the moment, I have a charging station (ebay from Hong Kong) so I can access the phone and try and resovle this.
I'm going to go back to the stock rom (I assume I'll find that somewhere on XDA) and upddate the Radio version and see if that sorts it.
If anyone has worked out what's casuing this generally let me know as I can imagine this will take a lot of trial and error to solve!
Thanks
have you fixed it?
i am having a similar issue:
I have recently updated my HTC HD2 rom to version 3.14.410.2.
After that i have installed tomtom navigator, but when i turn on the device it returned a message 'BTTRAYCE' is not a valid Pocket PC application'.
I looked at the forums and it was recommended to delete files Windows\BtSdkCE30.dll and
\Windows\BtCoreIf.dll, so i did.
Unfortunately my usb connection is now not working, and i think it could be related to the deletion of those 2 files.
I made a hard reset, but the problem still persists.
can anyone help me please?
My problem solved
Hi i got the same problem , i use ARTEMIS 48 rom 3.14. so my phone suddenly droped to the ground last night but i was charging after that .... next days morning i wanted to connect it to my pc via activesync but it dose not connect .... even disk drive did not work and i could not charge it via AC CHARGER and PC , i toyed around with it here is what i did
1- tried on another pc (result wass the same it did not worked)
2-i hard reseted it (result = the problem was not solved )
3-i went to setting>>>>system>>>power>>>battery and unchecked the option "when phone is on , do not charge ...."
4- i connected it to pc it was not recognozed by pc but it was charging !!!!!!
5-after that i connected it to AC ADAPTOR and it was charging !!!!!!
6- i decided to flash my rom and do a HSPL so my phone will not brick so i connected it to activesync via bluetooth and it was as sucess
7-mean while i was searching this forums
8- i checked my SPL ver
9- i soft-reset and stuning it was recognized by pc and everything was back to normal
in my XP i think it was due to BAD ASS ANDROID ROM and some custom roms bugs....
fpcraveiro said:
have you fixed it?
i am having a similar issue:
I have recently updated my HTC HD2 rom to version 3.14.410.2.
After that i have installed tomtom navigator, but when i turn on the device it returned a message 'BTTRAYCE' is not a valid Pocket PC application'.
I looked at the forums and it was recommended to delete files Windows\BtSdkCE30.dll and
\Windows\BtCoreIf.dll, so i did.
Unfortunately my usb connection is now not working, and i think it could be related to the deletion of those 2 files.
I made a hard reset, but the problem still persists.
can anyone help me please?
Click to expand...
Click to collapse
Uninstall TomTom and the problem goes away.
You can download versions on TomTom Navigator 7 with the Bluetooth files removed - like * HERE *
I don't have an OS installed...
This is due to aMAGLDR being installed and when I had the device open.. I created a 'temp' folder and my next task was to create a 'create_to_sd_root', well I renamed the temp folder to that... bad move? I think so. My system acknowledges the device, however I'm unable to access it. I.e. my computer(no icon), windows mobile center(not connected), etc. Please help! I need my phone!
MrHellas said:
This is due to aMAGLDR being installed and when I had the device open.. I created a 'temp' folder and my next task was to create a 'create_to_sd_root', well I renamed the temp folder to that... bad move? I think so. My system acknowledges the device, however I'm unable to access it. I.e. my computer(no icon), windows mobile center(not connected), etc. Please help! I need my phone!
Click to expand...
Click to collapse
I you were trying to flash Android you just need to flash Clock Work Mod (CWM) and then place the .zip file for the Android ROM on your SD card and use CWM to flash the Android ROM. It is links to Youtube videos in the OP of the thread showing you how to flash CWM and the ROM.
Are you could flash back to Win MO through USB and bootloader or SD card and bootloaderr.. If you go for USB and bootloader make sure you see USB in the white bar of bootloader befor tryng to flash the ROM. Also thew SD card metrhod will remove HSPL if you use a Official and not a custom ROM.
Well I've figured out how to get the android os on there, however I'm unable to locate the drivers for AD8? I'm still unsure about what folder/files need to be on my microSD if I'm running the Desire HD Froyo(current) I cannot access any internal/external(microSD). Help?
MrHellas said:
Well I've figured out how to get the android os on there, however I'm unable to locate the drivers for AD8? I'm still unsure about what folder/files need to be on my microSD if I'm running the Desire HD Froyo(current) I cannot access any internal/external(microSD). Help?
Click to expand...
Click to collapse
You have to use MAGLDR's mass storage option to get access to your SD card, or use the mount storage option in Clock Work Mod. I recomemd usingvthecnass storagecin MAGLDR though as I have had trouble gettingvthecdrivers for mount storage in CWM to install but have never had a problem with the mass storage option in MAGLDR.
T-Macgnolia said:
You have to use MAGLDR's mass storage option to get access to your SD card, or use the mount storage option in Clock Work Mod. I recomemd usingvthecnass storagecin MAGLDR though as I have had trouble gettingvthecdrivers for mount storage in CWM to install but have never had a problem with the mass storage option in MAGLDR.
Click to expand...
Click to collapse
How do I get back the loader without booting up? Obviously haven't been able to copy the rar files. Could this be why my GPS and other functions could not be working properly?
imanh said:
3-i went to setting>>>>system>>>power>>>battery and unchecked the option "when phone is on , do not charge ...."
Click to expand...
Click to collapse
Thanks this sorted my problem!
imanh said:
Hi i got the same problem , i use ARTEMIS 48 rom 3.14. so my phone suddenly droped to the ground last night but i was charging after that .... next days morning i wanted to connect it to my pc via activesync but it dose not connect .... even disk drive did not work and i could not charge it via AC CHARGER and PC , i toyed around with it here is what i did
1- tried on another pc (result wass the same it did not worked)
2-i hard reseted it (result = the problem was not solved )
3-i went to setting>>>>system>>>power>>>battery and unchecked the option "when phone is on , do not charge ...."
4- i connected it to pc it was not recognozed by pc but it was charging !!!!!!
5-after that i connected it to AC ADAPTOR and it was charging !!!!!!
6- i decided to flash my rom and do a HSPL so my phone will not brick so i connected it to activesync via bluetooth and it was as sucess
7-mean while i was searching this forums
8- i checked my SPL ver
9- i soft-reset and stuning it was recognized by pc and everything was back to normal
in my XP i think it was due to BAD ASS ANDROID ROM and some custom roms bugs....
Click to expand...
Click to collapse
I did the same but no work. I have issue #USB not recognized# after installed Android Transformer SD ver.
In three color screen I have USB connection working fine. I could install HSPL4, update Radio, but Win 6.5 has a USB problem.
I don't think this is a hardware issue or I am wrong?
Still confused. Should I take my phone to service?
Hi,
I have the similar problem with my hd2, but worse. Out of 3 different comouters I tried none can see the phone connected and gives me the error saying one of the USB device connected to this computer has malfunctioned and cannot be recognized. I have tried two different cables. I cannot connect my phone through latest magldr using USB flasher or USB mass storage modes. Moreover, when I connect my phone in rainbow screen (hspl screen where you install magldr), it should change to USB from serial but even that does not happen. ANy solutions?? I think its my phone.... Is there any way to revert this back to normal. I don't want a brick.
mcdoc said:
I did the same but no work. I have issue #USB not recognized# after installed Android Transformer SD ver.
In three color screen I have USB connection working fine. I could install HSPL4, update Radio, but Win 6.5 has a USB problem.
I don't think this is a hardware issue or I am wrong?
Still confused. Should I take my phone to service?
Click to expand...
Click to collapse
Your USB drivers for the defualt bootloader (multicolor screen) seem to be working fine, so no you do not have a hardware problem. You might want to uninstall Windows Mobile Device Center or Active Sync, which ever one your computer uses. Then re install it. Also go to device manager in your comtrol panel while you have hour HD2 booted up and connected via USB and clck on update drivers for hour phone, it should be listed in device manager.
kushki said:
Hi,
I have the similar problem with my hd2, but worse. Out of 3 different comouters I tried none can see the phone connected and gives me the error saying one of the USB device connected to this computer has malfunctioned and cannot be recognized. I have tried two different cables. I cannot connect my phone through latest magldr using USB flasher or USB mass storage modes. Moreover, when I connect my phone in rainbow screen (hspl screen where you install magldr), it should change to USB from serial but even that does not happen. ANy solutions?? I think its my phone.... Is there any way to revert this back to normal. I don't want a brick.
Click to expand...
Click to collapse
When you say your Serial in boorloader does not change to USB this tells me you are having driver issues or hardware issues with your micro USB port on your HD2. My bet is it is just driver issues. I sugest you uninstall and rei nstall Wimdows Mobile Device Center or Active Sync which ever one your computer uses. These programs contain the USB drivers for the HD2 and MAGLDR partialy relies on those drivers to. So maybe that will solve your problem.
Guys,
im in extremely deep **** now.I accidentally tried flashing a stock ROM via SD card and now ive gt a ROM code error and 00028002 'Not Allow" error.What makes this worse is that my Vista computer is not recognizing any USB connection when i connect my HD2 to the computer.If i need to flash a stock rom via RUU wrapper to get through this stupid ROM code error, i need a USB connection on the first place...which IS NOT WORKING NOW!!!...im using a 512MBLeo,which is now stuck at SPL-1.42(previously HSPL)...im sitting duck here guys...i really really need your help on this one.i cant boot normally into 6.5,i cant flash a new ROM,i cant use bootloader and flash a LEOIMG using SD card cus it returns the above errors and i cant use my PHONE!!!...im extremely frustrated and helpless.please help guys...thanks alot...
If I understand you can still get to bootloader correct?
Exactly what official ROM did you try to flash?
Where did you get the ROM from?
Just so you know you can still flash HSPL with the 1.42.0000 SPL you have.
ROM code error usually means that official ROM is not for that HD2.
I flashed '1.48.405.2' which i downloaded from the net(http://theunlockr.com/2010/04/22/how-to-get-the-htc-hd2-back-to-stock/)...I tried flashing LEOIMG(SD card method) from Elegancia GTX v5.0 ROM,but thats returning the same error plus...it gets stuck on the white 'loading screen'.I know i can flash HSPL or any other stock rom with my current SPL,but my USB connection is not working...thats exactly the problem now...any idea where to get the actual stock ROM for my HD2?...Maybe that might prevail...Thanks.
kawshigan said:
I flashed '1.48.405.2' which i downloaded from the net...I tried flashing LEOIMG(SD card method) from Elegancia GTX v5.0 ROM,but thats returning the same error.I know i can flash HSPL or any other stock rom with my current SPL,but my USB connection is not working...thats exactly the problem now...any idea where to get the actual stock ROM for my HD2?...Maybe that might prevail...Thanks.
Click to expand...
Click to collapse
Yes go to htc.com amd enter the serial number of your HD2 (can be found under the battery) and it will only let you download the ROMs that are for your HD2. Also make sure the HTC site you go to is for your part of the world, It has links on the site to go to HTC sites for other countries.
As for your no USB go to your device manager in control panel and find your HD2 ther while it is connected via USB it will be listed as unknown, mobile device, or something like that but it will be there. Just click on it once to get it to drop down to the actual device and then right click it and select update drivers and then select from internet. If this does not work download the latest version of Windows Mobile Device Center (WMDC) and install it to your computer and this should give you the drivers you need.
Alright ill try all that and get back to you.Thanks alot for your advice!
Error Resolved
First,i would like to say thanks to you, T-Macgnolia.The ROM downloaded from the HTC website, which i flashed via sd card worked like a dream...However, the same cant be said for my USB connection though(I tried everything you said).My computer still keeps dropping USB connections intermittently...i miraculously managed to flash HSPL 3 on my HD2 just before the USB connection dropped.I was running WM 6.5 and android previously and i want to dual boot wp7 and android...which needs a USB connection(for MAGLDR and WP7)...Charging works fine via AC charger and via USB port(its just USB connection itself...any ideas where the fault lies?).i personally think the problem lies with my USB cable(as other devices work fine with the USB ports in my laptop). Guess i just have to buy a new micro usb cable(...thanks for your advice again.
kawshigan said:
First,i would like to say thanks to you, T-Macgnolia.The ROM downloaded from the HTC website, which i flashed via sd card worked like a dream...However, the same cant be said for my USB connection though(I tried everything you said).My computer still keeps dropping USB connections intermittently...i miraculously managed to flash HSPL 3 on my HD2 just before the USB connection dropped.I was running WM 6.5 and android previously and i want to dual boot wp7 and android...which needs a USB connection(for MAGLDR and WP7)...Charging works fine via AC charger and via USB port(its just USB connection itself...any ideas where the fault lies?).i personally think the problem lies with my USB cable(as other devices work fine with the USB ports in my laptop). Guess i just have to buy a new micro usb cable(...thanks for your advice again.
Click to expand...
Click to collapse
Yeah buy a new cable and see if that helps. If the problem pursists then you probably have a problem with the pins in your micro USB port of your HD2 that are randomly loosing connection to the main board because the solder points for the USB port is become cracked, loose, or just seperating for some reason. You might can find a cell phone repair shop that can resolder the connections for you are just Chang the intierior main board out for you ifcthis is the problem.
Hello,
Today i have tryed to flash a new CWM on my HD2.
But i get always an error "USB init. Failed" so i've searched in google an in this forum for an solution but i haven't find any.
I've tryed to flash CWM in Bootloader mode but my pc's (2 XP ones and 1 Win7) don't detect my phone.
Please Help
install windows mobile device center to your pc.otherwise it doesn't recognize it.
I have installed WMDC. But it doesn't recognize it at all.
but cwm isnt flashed from bootloader? r u using magldr or clk?
MAGLDR but also in Flasher mode nothing happend. In WMDC i have already disabled USB Connections but also -.- nothing
try another pc. and last solution format pc(i did so a few weeks ago when i met the same problem)
after last time i formated my computer imy phone wasnt detected in computer ...in bootloader i couldnt see USB just serial ...i just installed activesync ...and right after phone was detected ...so try to install activesync and see
[q] htc hd2 flashing rom issue
Can anybody help me.I have MAGDLR and the Bootloader installed by a previous chap who owned the phone, all the correct versions. THe phone HD2 (T-Mobile), when I got it, had Gingerbread on,but the FM radio was not working,
so I thought an Upgrade was in order. I went to the MIUI website and downloaded the latest stable rom and followed the instructions as best as possible, but I had problems with the
Bootloader going from Serial to USB and being able to flash the rom like that. I then tried the loading the rom ZIP file to the SD card, and then using Clockwork orange recovery to
to install the ZIP file from SD card. That being said, I rebooted and the phone just stayed hung on the HTC logo screen. (And I didn't do a back up, before I started.)
I eventualy found a Jaws MIUI rom, that instaling via Clockwork Orange, worked, but it is Froyo and not a lot of stuff works very well. What is the correct procedure to install
from SD card, with Clockwork Mod Recovery? The Roms that I download, do I have to unpack the zip, do something on the files? I have read that depending on the rom that you have, when
doing a ClockWorkMod Recovery installation, that you need to have the right Size partition or image disk version of the Clockwork recovery MOD, But I can't swap and change this as my USB does not work between the phone and the PC.
I have installed active sysnc, does not work and I have tried this both on my Desktop and Laptop. As the one response suggests, Formatting your PC seems a bit extreme.
Help, Pleeeeeeeeez!
Thanks
Asdoos said:
Hello,
Today i have tryed to flash a new CWM on my HD2.
But i get always an error "USB init. Failed" so i've searched in google an in this forum for an solution but i haven't find any.
I've tryed to flash CWM in Bootloader mode but my pc's (2 XP ones and 1 Win7) don't detect my phone.
Please Help
Click to expand...
Click to collapse
try with another usb cable
After many tests with other PC´s and USB cables and different Windows / Linux installations I have noticed that my phone doesn't charge -.-
I think its an Hardware Porblem of my Phone. Does anyone know how to fix it?
Usb port is gone on your phone get it replaced.
Sent from my HTC HD2 using XDA App
Hello, I'd love to mention one thing bec I got the same problem like some fri. No need to worry fri.My problem troubleshooting is " Just install Windows Mobile Device Center". Thanks all and I love xda.
So, i have been looking for solution to my problem.
I have HD2 and wp7 on it. Yesterday i wanted to change it to android. So i uninstalled wp7 and downloaded one rom from xda. Everything went well, until it reported a problem. There wasn't usb connection. I tryed to install it a few times, but everytime the same problem.
Then i tried to install wp7 and wp6.5 and android. ROM's i downloaded from here. Everytime it report usb connection problem.
Now i cant to anything, and i cant install any rom, i cant install any radios, hspl etc. .. What i should do now, that i get it to work? Please, i need my phone. And sorry for my bad english, ask if you dont understand something
I've tried everything, i just run HD2 toolkit (task 29) but it also says that there are connection problem.
So i think the most serious problem is, that i have usb connection problems, how i can fix that?
Have you tried all your USB ports, or have you tried another USB cable.?
You could try installing WMDC or Activesync to PC just in case it a PC driver issue !
Yes i have tried all ports and 2 cables. I will try now active-sync.
Kritsi said:
You could try installing WMDC or Activesync to PC just in case it a PC driver issue !
Click to expand...
Click to collapse
Well, i'm using Windows 7, so i have to install WMDC? Thanks
Hmm, i think the problem is in phone, because yesterday, before i uninstalled wp7 the usb connection worked. Then i uninstalled wp7 and i installed also something new to phone (radio or something?).
So, is there any way to uninstall the broken 'file', or way to install new one, without usb-connection
mutru said:
Well, i'm using Windows 7, so i have to install WMDC? Thanks
Hmm, i think the problem is in phone, because yesterday, before i uninstalled wp7 the usb connection worked. Then i uninstalled wp7 and i installed also something new to phone (radio or something?).
So, is there any way to uninstall the broken 'file', or way to install new one, without usb-connection
Click to expand...
Click to collapse
No it is not because you flashed a different radio. The radio is software that is used for your data connection, cellular connection, blutooth, WiFi, and camera. Plus if the radio was "broken" your HD2 would be hard bricked. If you used your computer to install a radio recently then that means that either your drivers have gotten screwed up or your USB cable is damaged and can not be used to transfer data anymore.
I used my computer to install the radio, and i have tried to delete drivers. And if I remember correctly, the radio installation went stuck, but the whole radio-system was ok, because i used it when i had wp7. Can i install new radio from sd-card or something? Please everyone help me !
Edit: I forgot to tell that i can go to bootloader, and it shows me the USB mode. Will this help any?
I really hope that there are some way to solve the problem :s
Try another PC/Notebook & try re-installing WMDC ...
You could also look at flashing a radio & WM6.5 via SD card method ...
Thanks to everyone. I solve the problem.
I tried another computer and it works.. Yesterday i tried it also but it didnt work
Technology is amazing Love my HD2 <3
I currently have a MIUI android ROM installed but want to go back to WinMo 6.5 (stock). Now when i try to flash the ROM like i did before, its says on my PC USB Init failed, connection problem. The bootloader screen does say usb. Also when I try to flash trough the MAGLDR flash modus there is USB standing but i cant flash. I've also tried flashing the stock ROM from my SD card as an NBH file but it wont work.. Also repartitioning and all the stuff dont work because they all have te connection problem. I have tried multiple USB cables. Anyone know a solution??