Guys
this morning i wanted to try a new rom and did task 29 and reinstall the radio and magldr 1.13 , and when i conected the phone via flasher mode it dosnt connect with the computer the strange thing is it connect via mas storage, i can flash win mobile which i did so my cable works, but I cant flash any android or win phone 7 ,,,i recently formatted my Pc besides that i could do it without any issue earlier what could be the problem
Damn it i cant flash anything via MGLDR it doesn't get connected only WIN Mobile 6.5
Hi, I would think that the problem is that you have formatted your pc, so you don't have ADB installed. Install Android SDK and you will get ADB support.
Thanx , i will try thanx a lot
I didn't managed to get it done i installed the SDK but no luck can some one pls help me to get my phone connected vis usb to MGLDR
nishanthabgw said:
I didn't managed to get it done i installed the SDK but no luck can some one pls help me to get my phone connected vis usb to MGLDR
Click to expand...
Click to collapse
Hi,
You are missing the drivers that come from ActiveSync in XP or WMDC in Windows 7.
Install whichever is appropriate for you and see if that works.
malybru said:
Hi,
You are missing the drivers that come from ActiveSync in XP or WMDC in Windows 7.
Install whichever is appropriate for you and see if that works.
Click to expand...
Click to collapse
thanx will try nw
Related
My phone was working well. Then i installed the new rom from mdj, CM7.
At first it was working good, but then i plugged my phone to pc but it wasnt recognized anymore. So i wanted to change back to another rom. No matter what i did my pc and my netbook didnt recognize my phone anymore. then i tried to update the rom with CW and a fixed rom from CM7. Since then my phone tells me theres nothing to boot in nand. And pc still not recognizing my phone. Pls help me guys. im trying to fix this since 3 hours but nothing works...pls help me.
power off your phone (pull battery and put it back in)
hold volume down and power button until you get to the tri colored screen
plug the usb into the computer
flash over any RUU
i tried that allready but as i said pc dont recognize as usb...so at the screen it says serial and not usb...but still i tried to install it and it didnt work
When i boot the phone it says...nand kernel open failed...is there a way to install a nand rom completely over CW?
Then is sounds like your pc has the prob not the phone.
Reboot PC and also try re-instaling Mobile Device Center or ActiveSync depending on what version of windows you have.
sry i should have tell that too...i have windows 7 and mobile device center...i restarted pc a few times allready reinstalled the program too...but when it comes to installing device driver it tells me it couldnt be installed...and i dont know what to do
H-KaN said:
sry i should have tell that too...i have windows 7 and mobile device center...i restarted pc a few times allready reinstalled the program too...but when it comes to installing device driver it tells me it couldnt be installed...and i dont know what to do
Click to expand...
Click to collapse
have you tried reflashing winmo using sd card? then start all over again.
H-KaN said:
sry i should have tell that too...i have windows 7 and mobile device center...i restarted pc a few times allready reinstalled the program too...but when it comes to installing device driver it tells me it couldnt be installed...and i dont know what to do
Click to expand...
Click to collapse
Trying flashing your official WM Rom through SDcard. Once you are back in WM, you can flash your desire NAND Rom.
i took the ruu_signed.nbh from an official rom named it to leoimg.nbh and put it on my sd...started the phone with volume down and power...it is updating
radio-ok
rcust-ok
bootloader-ok
splash-ok
os-
configdata-
the first time the update didnt work and now its updating again and i hope it will finish and make it work again and not cancel again...
thank u for the advice...maybe it will work
H-KaN said:
i took the ruu_signed.nbh from an official rom named it to leoimg.nbh and put it on my sd...started the phone with volume down and power...it is updating
radio-ok
rcust-ok
bootloader-ok
splash-ok
os-
configdata-
the first time the update didnt work and now its updating again and i hope it will finish and make it work again and not cancel again...
thank u for the advice...maybe it will work
Click to expand...
Click to collapse
Hope everything goes well for you......Good Luck
yesssssssssssss phone starts again...winmo is installed! the only problem which left is that the pc dont recognize my phone...i reinstalled mobile device center...but it cant install the phone driver...what can be the problem? does anyone know a page where i can download just the driver and install it?
H-KaN said:
yesssssssssssss phone starts again...winmo is installed! the only problem which left is that the pc dont recognize my phone...i reinstalled mobile device center...but it cant install the phone driver...what can be the problem? does anyone know a page where i can download just the driver and install it?
Click to expand...
Click to collapse
better fully uninstall mobile device center using softs like your uninstaller and alike to totally clean the installation then plug in usb. Then let Windows 7 do its job in installing the driver.
i cant believe it :S for real i cant believe it...i just changed the usb cable and tried with it :S and it worked :S the driver got installed and now its working :S now thats curious...not working with original cable anymore but with a cable from the nokia n97 :S
Hello I am trying to get active sync to work but when i go into the bootloader and plug in the usb windows installs the driver for the sync from htc i really need to install magldr 1.13 but i cannot get past the driver any ideas
thanks in advance
You do not need active sync. If you want to install MAGLDR just start bootloader and flash from there Hold Volume Down while starting the phone you will get the TriColored screen plug the phone into computer at the bottom of the phone it will say USB then click ROMUpdateUtility in the MAGLDR folder you downloaded. If the phone doesnt say USB try a different USB port
cannot sync in bootloader
wrecless said:
You do not need active sync. If you want to install MAGLDR just start bootloader and flash from there Hold Volume Down while starting the phone you will get the TriColored screen plug the phone into computer at the bottom of the phone it will say USB then click ROMUpdateUtility in the MAGLDR folder you downloaded. If the phone doesnt say USB try a different USB port
Click to expand...
Click to collapse
I am going to try on a different computer this afternoon. But I tried Everything you said Got to the bootloader just fine i even tried running the ROMupdateutility as admin. It gets to the progress bar just after you click update and then comes back with a usb error. I cannot seem to figure what the problem is other than my driver is not working properly. so i tried to uninstall the driver and it keeps reinstalling the htc usb sync driver form the windows update. like i said ill try it on a different computer and see if that works. thanks for your reply though.
Yes the problem is in your computer. It happened same with my laptop an computer. I formated and installed fresh copy of windows on the laptop. Now it is O.K.
thanks alot that was i thought about doing but...... I have Like a terrabyte to backup
First try reinstalling ActiveSync and try using a different usb port (preferably one at the back of the pc). Boot into bootloader and connect to pc, you need to see "usb" displayed on the phone screen.
You need active sync from ms. Not from htc. It's the soft provided by ms to sync wm devices. Normally it's downloaded when you connect your device. Check if windows try to install the driver. After you will also need the adb driver. For this one you need the android sdk.
Sent from my HD2 using XDA App
Hello.
I have MDJ Cyanogenmod 7 v2.6 installed on my HD2.
Now i am trying to go back to windows or play with other roms and instal Magldr 1.13.
But when i try to install them. I have to use a Activesyns connection between my PDA and PC. But the only thing i can choose on my phone is USB Mass Storage (On/Off).
And then the installation fails because it can't find my phone.
How do i get a Activesync connection on Gingerbread.
Can't find it anywhere.
Paul1990 said:
Hello.
I have MDJ Cyanogenmod 7 v2.6 installed on my HD2.
Now i am trying to go back to windows or play with other roms and instal Magldr 1.13.
But when i try to install them. I have to use a Activesyns connection between my PDA and PC. But the only thing i can choose on my phone is USB Mass Storage (On/Off).
And then the installation fails because it can't find my phone.
How do i get a Activesync connection on Gingerbread.
Can't find it anywhere.
Click to expand...
Click to collapse
Considering it's early here, I'm having my coffee, I'm not going to flame you for the dumb question, you can't active sync your hd2 on android, active sync is for windows mobile only, just power down, and power back up holding the volume down button, it will go into bootloader mode, plug your usb cable and you'll see usb display at the bottom of the screen, now you should hear the phone connecting to your pc and you can run any windows mobile RUU and flash back to stock , or run task 29 and flash windows mobile.
Thanks!!! I really couldn't find it. Probaly because i was searching with the wrong thoughts.
It worked!
thank you sir...i was wondering the same mistake now i understoood
Hello I have a big Problem I think but I hope someone can help me.
I flashed a NAND.now i want to flash an new Android version with CW but when i enter the USB Flasher mode my pc is doing three sounds instead of the normal usb sound.I can see the MAGLDR in device Manager.
so long for the first Problem.
my second problem is when i run DAF.exe from the CW
i get 2 errorsrogram can not start because RAPI.dll is not on the computer.
I hope someone can help me.
ps:sorry for my english ^^
dmx489371 said:
Hello I have a big Problem I think but I hope someone can help me.
I flashed a NAND.now i want to flash an new Android version with CW but when i enter the USB Flasher mode my pc is doing three sounds instead of the normal usb sound.I can see the MAGLDR in device Manager.
so long for the first Problem.
my second problem is when i run DAF.exe from the CW
i get 2 errorsrogram can not start because RAPI.dll is not on the computer.
I hope someone can help me.
ps:sorry for my english ^^
Click to expand...
Click to collapse
Hi,
Make sure you have the latest version of ActiveSync in XP or WMDC in Windows 7 installed.
Or in Vista/Windows 7 to right click and run as Administrator
Resovled
malybru said:
Hi,
Make sure you have the latest version of ActiveSync in XP or WMDC in Windows 7 installed.
Or in Vista/Windows 7 to right click and run as Administrator
Click to expand...
Click to collapse
.
Thanks for the post!
This will do it
Thank you. Problem is solved.
Hey everyone!
I've searched the board, but I did not find anything releavant to my issue.
I've been trying to put Clockwork into my magdlr by running the DAF.exe, my HD2 is in USB flasher mode, but DAF.exe pops up and says it needs "RAPI.dll" to run. After that, it's unable to establish a connection to my device.
RAPI.dll is a part of active sync, which is not available for Windows 7, so what can I do to establish a connection to my device?
Thanks in advance
Best regards
panxter
the windows mobile device centre that ships with win 7 isn't the latest.
http://support.microsoft.com/kb/931937
install again from there, reboot phone and pc, and try again.
samsamuel said:
the windows mobile device centre that ships with win 7 isn't the latest.
http://support.microsoft.com/kb/931937
install again from there, reboot phone and pc, and try again.
Click to expand...
Click to collapse
After validating, it takes me back to the frontpage.. no download. Oh stupid microsoft-website! grr!
.
RE: found a dl somewhere else, same version, I'll get back to you after a reboot