Related
Was trying to install wp7 on my hd2, but now im stucked on magldr version 1.13. Forgot that the volume buttons doesnt work and i cant get the phone out of there. Try to load original rom or even task 29 but nothing becuase the pc doesnt recognize it. When the phone its booting it says something like cant boot from sd android kernel fail and then the menu and i can select only the first 1 boot wph.
Is there a way to get the phone out of there, or my only hope its to repair the volume button.
thanks
If you haven't been able to flash anything then as long as you just reboot your phone you'll just go back to whatever ROM you had previously
I have the same problem, after having upgraded to 1.13. Whenever i try to install a NAND version of Android, i am stuck with the splashscreen of the build i am trying to boot into. Bear in mind that every ROM i flash is flashed without any problems. So I guess it is not the NAND memory thats broken or faulty. The only build i am capable of running, is DFT's WP7 stock build. This loads perfectly, but due to the battery drain i would VERY much like to get rid of it and use my beloved MDJs Gingerbread/CM7 2.6 build.
To avoid any trouble i thought of just flashing a Task29, and a stock WM65 ROM to 'reset' to stock, that is, installing a custom ROM from SD card, so SPL is restored to factory version. However, i am not able to enter bootloader mode on my HD2. It can only boot into Magldr and succ. WP7. It doesn't help to press vol down, and it is not broken as I can use it in WP7. It seems as though HSPL is skipped and the phone is boot directly into magldr. This should NOT happen.
Anyways, this is very much close to a bricked device for me, so i am very sad these days. Does ANYONE know a trick that would enable me to replace magldr 1.13 with the working 1.12 without the tri-colour bootscreen of spl?
i remove the battery but when the hd2 start again it boots instantly to magldr, i need another way to flash it different to the three color screen (i cant get there becuase the volume down button its broke).
i have a problem like that
If your volume keys don't work, then there is seriously, no other way. You can't get into bootloader mode without the volume keys, and the you can't flash a different rom without the volume keys, so yeah, your device is pretty much bricked....
But IF the vol. down key works, I assume that it is something with MAGLDR or HSPL, or possibly an error in RAM. Are there anything that can be flashed via magldr that checks the state of underlying HSPL?
any fix to this??? same issue following the steps and volume buttons dont work. I can select the boot wph ....wph not installed
Maybe I'm tired or too old... but I don't understand your questions
You can imagine the different "softs" as layers:
1st: HSPL (or SPL) - it's the one you enter by pressing vol-down while booting.
this one give you the ability to flah a WM ROM (original or custom), a radio or MAGLDR
So if vol-down if dead... your phone also
nb: the first splash screen is at this level, so it will be still here after flash of MAGDR, CWM, NAND, WM7...
2nd: MAGLDR - it's the one you go in by pressing "end call" while booting.
It gives the ability to flash a NAND or WM7 via DFT
So if "end call" is dead... you're not But it's anoying I think...
3rd: CWM - it's the one you go in by selecting "AD recovery" in MAGLDR
It gives you the ability to flash a "CWM NAND" or an update... It also gives the ability to backup/restore a NAND.
So please clarify your question if you need help. More important do not post different problem by saying "same here". It's just confusing. Even if you can't boot your NAND it's not always the same problem
Let's try again dudes
osugsxr said:
any fix to this??? same issue following the steps and volume buttons dont work. I can select the boot wph ....wph not installed
Click to expand...
Click to collapse
HTC after sales... or few bucks
That is what I'm thinking, will try warranty to see if that works if not not ill see what they charge. For now back to the nexus s.
truc007 said:
HTC after sales... or few bucks
Click to expand...
Click to collapse
Sent from my Nexus S using XDA App
This is the answer to your problem if it does work find someone that is not a noob and have them fix your phone its really not that hard
Ok guys please help me I don't wanna start new thread
I installed on my hd2:
-HSPL 2.08
-Radio 2.15.50.14
-Magldr 1.13
-CMR
First of all I noticed that I dont have to hold the power button to get into the magldr menu.
I couldn't get into Boot As SD so I wanted to flash custom rom from bootloader. Unfortunately I can't do that. Even tried HR. Is there any solution to flash stock ROM
Any help would be greatly appreciated
Stuck for me too
I just flashed the latest hspl3, radio code and MAGLDR 1.13.
When I try to boot MCCM 4.5 from SD it hangs on the main Android Home Screen. When I try to boot WPH MAGLDR says that WPH is not installed.
I am still running Windows Mobile 6.5.
Any help would be greatly appreciated.
hi, have u tryed with the small button under the volume down button? it works as the volume down button...
If u can go in bootloader (if ur volume down works) could be ur nand is corrupted (as mine ) so bye bye hd2... i m waiting for the htc sensation
DAF doesnt' work
ChitownWingMan said:
I just flashed the latest hspl3, radio code and MAGLDR 1.13.
When I try to boot MCCM 4.5 from SD it hangs on the main Android Home Screen. When I try to boot WPH MAGLDR says that WPH is not installed.
I am still running Windows Mobile 6.5.
Any help would be greatly appreciated.
Click to expand...
Click to collapse
I figured out the Android problem (I needed a different rootfs).
I have magldr 1.13 working!!!!
However, when I try to run DAF I get the same:
"An error has occurred
Read below for more information
Error Description: Config load failed.
Info: .\RSPL\RSPL.cpp (725)
Error Description: CONFIG: can't open config file
Info: .\RSPL\RSPL.cpp (304)"
error that I have seen all over XDA-Dev.
However, none of the fixes I have seen on here have worked. I am running Windows 7 Professional.
I have tried:
Disabling Use USB in the Window Mobile Device Center
I have tried ANDR_INSTALL
I have rebooted
I have tried deleting all of the unattached USB device in the device manager.
I have tried using LeoAdvancedRUU
I have tried starting DAF first and then connecting the usb cable
I have tried connecting the USB cable first and then the starting DAF.
Help please!!! I was up until 8:30 AM trying to get this to work (I started at about 10:00 PM).
i also put the hd2 into the freezer for 10 minutes to solve heat problem and it doesn't start bootloaderi...
the nand corrupted..it start magdle but don't start android or cwm..there is nothing to do
tser04 said:
I have the same problem, after having upgraded to 1.13. Whenever i try to install a NAND version of Android, i am stuck with the splashscreen of the build i am trying to boot into. Bear in mind that every ROM i flash is flashed without any problems. So I guess it is not the NAND memory thats broken or faulty. The only build i am capable of running, is DFT's WP7 stock build. This loads perfectly, but due to the battery drain i would VERY much like to get rid of it and use my beloved MDJs Gingerbread/CM7 2.6 build.
To avoid any trouble i thought of just flashing a Task29, and a stock WM65 ROM to 'reset' to stock, that is, installing a custom ROM from SD card, so SPL is restored to factory version. However, i am not able to enter bootloader mode on my HD2. It can only boot into Magldr and succ. WP7. It doesn't help to press vol down, and it is not broken as I can use it in WP7. It seems as though HSPL is skipped and the phone is boot directly into magldr. This should NOT happen.
Anyways, this is very much close to a bricked device for me, so i am very sad these days. Does ANYONE know a trick that would enable me to replace magldr 1.13 with the working 1.12 without the tri-colour bootscreen of spl?
Click to expand...
Click to collapse
I have the same exact problem !! WP7 is the only OS that works and I want android
also the volume down key works...should I try to reflash HSPL ?? will that work ?? since HSPL 2.08 is already installed !??
Happen error
Read below for more information
Error Description: Config load failed.
Info: .\RSPL\RSPL.cpp (712)
Error Description: CONFIG: can't open config file
Info: .\RSPL\RSPL.cpp (291)
Hi all,
I'm brand new in the art of updating mobiles.
I would like to update my HD2 to andriod but have no idea of how I do it. I have looked at a lot of threads but it seems that I need ot know a lot about my phone before I can start!!
Can anyone help me how and where to start?! What do I need to install and how do I install it :/
My phone data:
OS version 5.2.2.1913 (21913.5.0.94)
Manila version 2.5.20181527.0
ROM version 3.14.403.2 (04666) DAN
ROM date 10/4/10
Radio version 2.15.50.14
Protocol version 15.42.50.11.U
When I press volume down and start my phone it say
PB81100 HX-BC
SPL-3.03.0000 XE
MicroP(LED) 0x05
MicroP(TOUCH) 0x50
Best regards,
Peter
Knowledge is power my friend and d answers u seek are but a click away...All u have 2 do is read, read n do more reading...follow all instructions written by devs to d letter as they were written for a reason...Wat reason?...
Avoiding errors or turning your beloved HD2 into an "Expensive Paper-Weight"....Getting android onto ur device is quite easy, u just have 2 put in d time 2 understand certain terms n how d needed softwares work...So summary?...Start reading from here. When u have properly familiarized urself with flashing then visit the HD2 android development section n check out several builds available...u must make a choice urself as we wouldn't know wat u lyk...so feel free 2 test as many as u can.
P.S. Its crucial u first perform a HSPL (2.08 HSPL) on ur fone before doing ANYTHING else.
The post above isn't really helpful. He's obviously read a lot already lol.
I know getting in to flashing and stuff on the HD2 is very confusing at the start, but once you learn it once you learn it forever.
Basically first off, you need to flash HSPL 2.08 to your phone. To do so download 'HSPL4' from these forums and flash that. Just search for it and you'll find it. It'll have instructions on how to install it on the thread which is very easy.
Just boot to SPL and connect to USB and run the .exe file inside of HSPL4 and choose 2.08.HSPL from the drop down menu.
After this you need to flash the newest radio which is 2.15.50.14. There's a sticky in all the HD2 development threads that have all the radio's. Just look in the WinMo or Android section and it'll be stickied. You basically then open the file you downloaded with the radio in it, boot to HSPL (you've just flashed HSPL over SPL) and run the RomUpdateUtility and just click on all the next and update buttons on the window that'll pop up and it will install. Obviously you need your USB cable plugged in for this too.
After that, you need to flash MAGLDR. I can't get links at the moment but you should easily be able to get a link to the MAGLDR thread and download it. After you've downloaded it to your PC, it's basically the exact same procedure as flashing a radio. Bootloader > USB connected to phone > open RomUpdateUtilty and follow instructions and flash. After this finishes installing you're basically done and all you need to do is flash your Android ROM. Just go in to the NAND Development section and chose a ROM to start from.
Another option is to flash Clockworkmod Recovery after MAGLDR.
You simply flash that by going in to MAGLDR (keep holding power/end key while phone is booting) and go to USB Flasher using your volume buttons then going in to it by the call button. Then opening the .DAF file on your PC and following the instructions and clicking next. Obviously again with your USB cable plugged in too. This is how you flash ROM's/Clockwork.
Any other problems I'd be more than happy to help with.
Just to mention too - the HD2 is very difficult to brick so don't worry about bricking your phone as I don't think there's actually a way to do it other than flashing the wrong radio if you have a TMoUS HD2 and you flash a .51 radio which you won't do as I've told you the correct radio to flash.
from the info he posted about his phone, it seems it already has the latest radio installed (2.15.50.14) I'm guessing that he's got a phone from somewhere in EU since the TMOUS came with the 2.08.50 radio, unless I'm mistaken, and there are some later models of the US hd2 that have the 2.15 radio, but anyways if the info is correct then he doesn't need to worry about the radio, he needs :
HSPL4> 2.08hspl http://forum.xda-developers.com/showpost.php?p=11499585&postcount=3
Task 29 http://forum.xda-developers.com/showthread.php?t=644781
MGLDR http://forum.xda-developers.com/showthread.php?t=893618
Clockworkmod Recovery http://forum.xda-developers.com/showthread.php?t=898913
any more info go here http://forum.xda-developers.com/showthread.php?t=905841
and his rom of choice. I'm sure with this info he can get to where he wants to go, good luck!
Woops my bad, didn't even read the OP info part. Well done for posting the links though as I can't at the moment.
Also about clockwork, make sure the you have the right clockwork partition for the ROM or else you'll get stuck on a boot-loop. You'll usually find the partition info in the ROM thread and then you just edit the flash.cfg file found in your clockwork folder using notepad.
Hi
Thanks a lot for all your help, it made it a lot easier for me to start )
I have now installed
HSPL4> 2.08hspl http://forum.xda-developers.com/show...85&postcount=3
I didnt do this (radio update, since as I understood I already had the right one!!??, Yes the phone is from Denmark)
Task 29 http://forum.xda-developers.com/showthread.php?t=644781
Then I downloaded MGLDR and run the ROMUpdateUtility
MGLDR http://forum.xda-developers.com/showthread.php?t=893618
BUT it say that it may take upto 10 minutes, it take below 1 minute for me... the statusbar at the host computer goes from 0 to 100% fast and the same on the phone and after that the phone restart and show "HTC" in green with white background... then it simply stops.......
What have I done wrong and how can I solve it?!
Thanks in advance for all your input.
Best regards,
Peter
PeterSvendsen said:
Hi
Thanks a lot for all your help, it made it a lot easier for me to start )
I have now installed
HSPL4> 2.08hspl http://forum.xda-developers.com/show...85&postcount=3
I didnt do this (radio update, since as I understood I already had the right one!!??, Yes the phone is from Denmark)
Task 29 http://forum.xda-developers.com/showthread.php?t=644781
Then I downloaded MGLDR and run the ROMUpdateUtility
MGLDR http://forum.xda-developers.com/showthread.php?t=893618
BUT it say that it may take upto 10 minutes, it take below 1 minute for me... the statusbar at the host computer goes from 0 to 100% fast and the same on the phone and after that the phone restart and show "HTC" in green with white background... then it simply stops.......
What have I done wrong and how can I solve it?!
Thanks in advance for all your input.
Best regards,
Peter
Click to expand...
Click to collapse
Sometime wrong radio can cause that issue.
Make sure that the radio is 2.15.xxx.xxx.
Now, you should go into bootloader and try to flash the radio, and then restart doing task 29, flashing MAGLDR.
If you succeed, your phone will automatically bring you into MAGLDR screen.
From there you can flash Android or WP7
Good luck
I now downloaded my "old" radio version 2.15.50.14
http://forum.xda-developers.com/showthread.php?t=611787
It seems to complete.. didnt jump from 0% to 100% in 1 sec..... so thats good
Then the task29 seems to work as well since my ROM is clean!!
BUT agian when I romupdate MGLDR it start and complete very fast... goes from 0 to 100% within a few sec...
http://forum.xda-developers.com/showthread.php?t=893618
and agian stops at the HTC startup screen.....
As extra information I can say that when I try to install MGLDR the RomUpdate state that the current image version is... blank
and that I can install Image Version 2.00.000.0
And then when I start it takes a few sec.....
What OS do you use on your PC? If it's Vista/Windows 7, you may need to run as administrator, if you haven't done so already
Sent from my HTC HD2 using XDA App
I'm using WinXP as OS
I'm using WindowsXP as OS.
I have not had any problem using the programs so far.. so I guess I have all the right rights!
UPDATE:
Can it be a problem with the SD card if there are no connection or a defect card?
I get exactly the same behavior if I remove the SD card from the phone!
PeterSvendsen said:
I'm using WindowsXP as OS.
I have not had any problem using the programs so far.. so I guess I have all the right rights!
UPDATE:
Can it be a problem with the SD card if there are no connection or a defect card?
I get exactly the same behavior if I remove the SD card from the phone!
Click to expand...
Click to collapse
Hmmm...You r flashing MAGLDR 1.13? Try flashing witout ur sd card & sim card present...if dat still doesn't work then try another pc, possibly one with Windows 7 (though it works on xp)...Task 29 always.
Hi everyone! After checking the forum on possible quirks that can be encountered when installing MAGLDR I hope someone can help me with the following:
I am trying to install Android on the HD2 via full-NAND-flash (i.e. directly via USB without SD card). I read tons of webpages and I believe I understood the necessary steps. Check the SPL; Install Hspl; Install MAGLDR; etc.
I tried to install MAGLDR 1.13 and everything went nice and quick: 100% complete on the phone; 100% complete on the PC; click on finish; phone reboot .......... and now the HD2 does not go past the green-on-white HTC splash screen. No boot.
I can still acess the colour-striped bootloader, which reacts if I connect the USB cable. No more.
What have I done wrong? Can it be recovered?
Thanks in advance for any suggestion.
You need to do a bit more reading (it's fundamental). Flashing MAGLDR is only the first step in getting Android on NAND. Next, you'll need to flash CWM and if you're going to install Android, you are going to have to have an SD card.
It's clear you read enough to get as far as you have. I suggest doing a bit more.
Start here:
http://forum.xda-developers.com/showthread.php?t=905841
Thanks but I don't think I can do much more at this point. The phone seems to be stuck (see my initial post). Cheers,
Did you try holding the Red power button down while the phone was powering up? That should take you into the Magldr menu.
Also, since you say you can get into the bootloader, have you tried reflashing Magldr?
Yes, I did. However, in the flash window, where you should see you are going from ROM version X to ROM version Y, this information does not show. The flash process seems to go through normally but then the situation is the same one.
The bootloader I can access is the normal one, with the red-green-blue stripes: it shows:
PB81100 HX-BC
SPL-2.08.HSPL 8G XE
0x05
CotullaHSPL 0x30
On the bottom it reads "serial" and if I connect the USB cable it changes to "USB".
Do a task 29.
Flash radio 2.15
reflash magldr
Hope this helps
yz.hd said:
Flash radio 2.15
Click to expand...
Click to collapse
I think this is the case sensitive for the OP explained symptoms.
Flash 2.15 or any Radio Rom that supports 576MB.
I have used Task29+radio 2.15.50.14, the doloop file repackaged by shadrac.....
So in principle the radio should be the correct one.
Shall I try with the separate flashes? Would you please let me have the links to download them?
(beginning to despair.....)
Thanks
Use HD2 Toolkit to re-flash MAGLDR 1.13... easiest and most comprehensive tools.. If u still stuck, re-install WM ROM (better custom ROM since u want to install AD NAND) this w keep ur HSPL. Once u are back to WM, repeat the whole cycle use the kit (pls confirm ur Radio 2.xx.50.xx (above 2.07.50.xx) and not the .51.
gd luck
Norton 360 doesn't like the HD2 tkit...
Any idea why Norton 360 discards the download telling me the HD2 Toolkit is a threat? That's odd...... the download link comes from this very site.
Anyone else with the same experience? Cheers!
Hey all,
Firstly, I know there are many similar threads posted here, but none of them actually gave a solution to a problem I have.
What I did: tried to eventually put WP 7.8 using Pdaimatejam's ROM.
*My HD2 runned on WM 6.5 and was completely original
I followed all steps in chronological order:
-Installed HSPL 2.08.HSPL - Succeeded
-Installed MAGLDR - Says it succeeded
NOW, it rebooted itself, since then it always freezed at the White HTC LOGO screen.
By booting via the bootloader (Volume down+Powerbutton) I get the following information:
PB81100 HX-BC
SPL-2.08.HSPL 8G XE
0x05
CotullaHSPL 0x40
I still see Serial at the bottom. When Plugging in USB it shows that it's connected with USB.
Important:
I have tried to install MAGLDR again: Same result. It says it succeeded, but is stuck after booting.
I have NEVER seen the MAGLDR bootup (The black list)
I have NOT put an SD-card when doing this all (Maybe that's the problem)
I also have NOT done anything with the Radio, because I diidn't know exactly what it is and I didn't think it was necesserily.
Any help would be very very very appreciated.
- TSeven
You can't just skip steps and expect everything to work properly. Flash radio 2.15.50.14, then I think you should be fine. Also, how are you planning on running WP7 without an SD card? Buy one or if you have one (which you should) put it in the phone. Flashing HSPL, MAGLDR, the radio etc. won't interfere with your SD or SIM card.
sdcard is WP7 main memory... you must have SDcard during flashing process in phone...
read install tutorial from my signature
Nigeldg said:
You can't just skip steps and expect everything to work properly. Flash radio 2.15.50.14, then I think you should be fine. Also, how are you planning on running WP7 without an SD card? Buy one or if you have one (which you should) put it in the phone. Flashing HSPL, MAGLDR, the radio etc. won't interfere with your SD or SIM card.
Click to expand...
Click to collapse
I'll put an 2GB SD card in my HD2. Can I now Flash my phone with Radio 2.15.50.14 and will my problem be solved now?
Or should I first Flash Radio, then HSPL again and then MAGLDR again?
Thanks for your response by the way.
soedhier007 said:
I'll put an 2GB SD card in my HD2. Can I now Flash my phone with Radio 2.15.50.14 and will my problem be solved now?
Or should I first Flash Radio, then HSPL again and then MAGLDR again?
Thanks for your response by the way.
Click to expand...
Click to collapse
is not important when you flash radio... just flash it...
I think radio then MAGLDR. You don't need to reflash HSPL though.
Thanks all for helping me out, still have to search for the 2GB sd card... I'll tell you guys Monday if it worked.
Hey all,
Thanks for all your help! I'm stuck again though..
I've put an 4gb sd card into my HD2 and have flashed my phone with
the radio (Radio_Leo_2.15.50.14)
After flashing, I didn't got the MAGLDR bootloader, so I (like Nigeldg said) flashed my phone with
MAGLDR afterwards.
After that It worked and now I'm able to enter the MAGLDR bootloader with no problems.
Entered USB Flasher and:
put a WP7 (although, that's what I thought) ROM on my phone...
The name of the file is ( 3_HD2 Pdaimatejam Rom Wp7.8 OS 7.10.8835.35 v8.5 )
After installation however the installation program gave me 3 errors:
An error has occurred
Read below for more information
Error Description: send d000ff partition data failed
Info: .\RSPL\RSPL.cpp (1279)
Error Description: block send fail
Info: .\RSPL\RSPL.cpp (962)
Error Description: Block is after end.
Info: .\RSPL\RSPL.cpp (704)
I AM able to boot my HD2 and Windows 8 (surprisingly 8) booted normally, untill it said that it doesn't recognise my sd card. Only
option is to shut down my HD2.
I'm now thinking to put another ROM on it, I already installed on my pc only (3_HD2_20Pdaimatejam_20Rom_20Wp7.8_20OS_207.10.8858.136_20RMT_20v8.7) from Dxdy's links.
When I deleted my sd card from my HD2 and booted it, it still booted normally with the Windows 8 loading screen and the error about the sd.
I want to delete at first that ROM and put another one on it. How can I delete it? It is ( I think) not installed on the SD.
Tseven007 said:
Hey all,
Thanks for all your help! I'm stuck again though..
I've put an 4gb sd card into my HD2 and have flashed my phone with
the radio (Radio_Leo_2.15.50.14)
After flashing, I didn't got the MAGLDR bootloader, so I (like Nigeldg said) flashed my phone with
MAGLDR afterwards.
After that It worked and now I'm able to enter the MAGLDR bootloader with no problems.
Entered USB Flasher and:
put a WP7 (although, that's what I thought) ROM on my phone...
The name of the file is ( 3_HD2 Pdaimatejam Rom Wp7.8 OS 7.10.8835.35 v8.5 )
After installation however the installation program gave me 3 errors:
An error has occurred
Read below for more information
Error Description: send d000ff partition data failed
Info: .\RSPL\RSPL.cpp (1279)
Error Description: block send fail
Info: .\RSPL\RSPL.cpp (962)
Error Description: Block is after end.
Info: .\RSPL\RSPL.cpp (704)
I AM able to boot my HD2 and Windows 8 (surprisingly 8) booted normally, untill it said that it doesn't recognise my sd card. Only
option is to shut down my HD2.
I'm now thinking to put another ROM on it, I already installed on my pc only (3_HD2_20Pdaimatejam_20Rom_20Wp7.8_20OS_207.10.8858.136_20RMT_20v8.7) from Dxdy's links.
When I deleted my sd card from my HD2 and booted it, it still booted normally with the Windows 8 loading screen and the error about the sd.
I want to delete at first that ROM and put another one on it. How can I delete it? It is ( I think) not installed on the SD.
Click to expand...
Click to collapse
First you must go to Magldr to activate the last 24MB
>10 Services>4 UseLast24MB
If this doesn't help, you must use another SD-Card. WP doesnt like any type of card. I use a SanDisk Class 4 card whitch works fine. Search in the forums other persons experiences with SD-Cards. Changing the ROM won't help.
Tseven007 said:
Hey all,
Thanks for all your help! I'm stuck again though..
I've put an 4gb sd card into my HD2 and have flashed my phone with
the radio (Radio_Leo_2.15.50.14)
After flashing, I didn't got the MAGLDR bootloader, so I (like Nigeldg said) flashed my phone with
MAGLDR afterwards.
After that It worked and now I'm able to enter the MAGLDR bootloader with no problems.
Entered USB Flasher and:
put a WP7 (although, that's what I thought) ROM on my phone...
The name of the file is ( 3_HD2 Pdaimatejam Rom Wp7.8 OS 7.10.8835.35 v8.5 )
After installation however the installation program gave me 3 errors:
An error has occurred
Read below for more information
Error Description: send d000ff partition data failed
Info: .\RSPL\RSPL.cpp (1279)
Error Description: block send fail
Info: .\RSPL\RSPL.cpp (962)
Error Description: Block is after end.
Info: .\RSPL\RSPL.cpp (704)
I AM able to boot my HD2 and Windows 8 (surprisingly 8) booted normally, untill it said that it doesn't recognise my sd card. Only
option is to shut down my HD2.
I'm now thinking to put another ROM on it, I already installed on my pc only (3_HD2_20Pdaimatejam_20Rom_20Wp7.8_20OS_207.10.8858.136_20RMT_20v8.7) from Dxdy's links.
When I deleted my sd card from my HD2 and booted it, it still booted normally with the Windows 8 loading screen and the error about the sd.
I want to delete at first that ROM and put another one on it. How can I delete it? It is ( I think) not installed on the SD.
Click to expand...
Click to collapse
also same error for me,,,,,used class 4 sd card but no use
this error dont have anything with SDcard.... you not read install instructions... read tutorial from my signature
Error Description: send d000ff partition data failed
Info: .\RSPL\RSPL.cpp (1279)
Error Description: block send fail
Info: .\RSPL\RSPL.cpp (962)
Error Description: Block is after end.
Info: .\RSPL\RSPL.cpp (704)
Click to expand...
Click to collapse
my buttons (call key etc) dont respond in magldr boot screen.
dxdy said:
this error dont have anything with SDcard.... you not read install instructions... read tutorial from my signature
Click to expand...
Click to collapse
Hi all, not too hopeful for a reply since this thread is OLD.
I just got an HTC HD2 from my brother..its used etc. anyway.. it was running fine on winmo 6.5.
I decided to checkout online for tips on mods n getting it to look and run like a newer device? I thought id go for android ICS.
So, followed the steps and got the required items first. HSPL, Radio CUU and the HD2 toolkit that includes the magldr 1.13.
the first two flashes for hspl and rom were okay, however after flashing magldr, once the fone boots up in magldr mode, i could scroll up and down using the volume buttons but i cant SELECT anything, hence.. i cant get to the USB flasher mode to complete my 'quest'.
Has anyone experienced this or know why this happens? I am currently unable to use the fone.
judheim said:
... however after flashing magldr, once the fone boots up in magldr mode, i could scroll up and down using the volume buttons but i cant SELECT anything, hence.. i cant get to the USB flasher mode to complete my 'quest'.
Has anyone experienced this or know why this happens? I am currently unable to use the fone.
Click to expand...
Click to collapse
use green button to execute selected option...
Tseven007 said:
I'll put an 2GB SD card in my HD2. Can I now Flash my phone with Radio 2.15.50.14 and will my problem be solved now?
Or should I first Flash Radio, then HSPL again and then MAGLDR again?
Thanks for your response by the way.
Click to expand...
Click to collapse
Thanks, it's worked for my HTC PB81100, it stuck at HTC boot logo and now it's fixed
nooop
Pal ... Maybe Your Phone has The Special pack That is Unable to use Magldr ...
I had the problem of White Screen after installing Magldr
I had the same problem of White Screen after installing Magldr. Turns out it was the radio so followed the instructions Here >>>> .addictivetips.com/mobile/install-2-15-50-14-radio-on-htc-hd2
<<<<
Once installed it rebooted into MAGLDR then i could install a ROM.
Love this site btw!
Hello everybody,
i am trying to install android and i have a lot a problem.
First of all, the phone belonged to my bro. One year ago, he wanted to install android but he failed and he bought an other phone. Because it's a good phone, i have decided to do it but it's not very easy....
The phone: white screen without HTC logo, hspl 2.08spl installed
My pc: W7 /usb ok
What i tried:
- change the hspl version : i tried to install an other version, just to try the soft and it was written on the screen that it's a success but nothing change on the version. I mean, i tried to install the 3.03 version but the version stay on 2.08spl even if the message is a success.
- lauch Task29: it's not working. I have a msg error
- install a rom: same problem
I dont remember exactly which error message it was. One was due to a communication error and the other because of the corruption of the imag(error 276).
Do you have an idea?
kam10 said:
Hello everybody,
i am trying to install android and i have a lot a problem.
First of all, the phone belonged to my bro. One year ago, he wanted to install android but he failed and he bought an other phone. Because it's a good phone, i have decided to do it but it's not very easy....
The phone: white screen without HTC logo, hspl 2.08spl installed
My pc: W7 /usb ok
What i tried:
- change the hspl version : i tried to install an other version, just to try the soft and it was written on the screen that it's a success but nothing change on the version. I mean, i tried to install the 3.03 version but the version stay on 2.08spl even if the message is a success.
- lauch Task29: it's not working. I have a msg error
- install a rom: same problem
I dont remember exactly which error message it was. One was due to a communication error and the other because of the corruption of the imag(error 276).
Do you have an idea?
Click to expand...
Click to collapse
My advice is for you to start over from scratch turkey...put the device in bootloader mode and run the AIO HD2 Toolkit and perform a Task 29; once done, put the device in bootloader mode again and run MAGLDR. If you're dead in the water at either of these...get drunk and sing to your cat!
berrywr said:
My advice is for you to start over from scratch turkey...put the device in bootloader mode and run the AIO HD2 Toolkit and perform a Task 29; once done, put the device in bootloader mode again and run MAGLDR. If you're dead in the water at either of these...get drunk and sing to your cat!
Click to expand...
Click to collapse
Like U said I run the AIO HD2 TOolkit and perform a task 29 but I have an error 286 The Nand Flasher Utility has encountered communication errors during the update process...)
Install last HtcSync version
After
If in the bootloader you read on the second line you can read SPL-2.08.HSPL
flash a radio Rom (2.12 or 2.15)
Try to install Clk 1.5.x (Leoimg.nbh on sd card root, you have to start your hd2 with power + vol- at the same time and follow the instructions)
After you can enter in Clk (power + arrow touch) , settings, resize system partition, and after go to recovery to partition your sdcard and install the zip of the rom of your choice....
bzhmobile said:
Install last HtcSync version
After
If in the bootloader you read on the second line you can read SPL-2.08.HSPL
flash a radio Rom (2.12 or 2.15)
Try to install Clk 1.5.x (Leoimg.nbh on sd card root, you have to start your hd2 with power + vol- at the same time and follow the instructions)
After you can enter in Clk (power + arrow touch) , settings, resize system partition, and after go to recovery to partition your sdcard and install the zip of the rom of your choice....
Click to expand...
Click to collapse
I installed the last HTCSync, I checked again my bootloader, and it's the 2.08 HSPL.
I try to flash a radio rom but it failed (ERROR 270- update error: the image file is corrupted.). I try again and it failed again but with an other error message(ERROR 286-update error: the ROM Update Utility has encountered communication errors during the update process).
May I have to try to install Clk or it's not neccessary because I don't have a sd card?
the easiest way is with a SdCard, but it's possible with Hd2 Toolkit ...
bzhmobile said:
the easiest way is with a SdCard, but it's possible with Hd2 Toolkit ...
Click to expand...
Click to collapse
It found a sd card. I will try with this method.
:good:
Nothing working... Still the same message error...
Is my phone dead? Someone can help me? Pleeeeeaaaaaase!!!!!!!!!!!!!!!!!
download stock windows mobile rom. if it's an eu hd2, download an international rom. if it's tmous (tmobile usa), download its' rom.
What i mean is to download the corresponding rom to your device. be sure not to flash the wrong one.
before you start, download hspl4 package from here
run it on your computer, and install 2.08 HSPL (i know you have it, reinstall it)
next run the ruu executable you downloaded (the windows mobile rom i told you to download)
if it flashes, you can flash magldr and try. try AFTER you flash windows mobile, and a RADIO (suggesting 2.15)
if that doesn't work, extract the nbh from the executable, install SPL3.03 , rename nbh to LEOIMG.nbh , in capital letters, put it on your sd<= 4gb
turn phone in bootloader, you should be able to flash the rom. after flashing it reflash hspl and magldr
bro..download windows mobile device center software..Install it on your PC..Then install hd2 toolkit. switch off your hd2. Press volume down and power button until it shows 3 coloured screen.then install hspl,repeat the step and then install magldr,then let it boot up. then select the usb flasher on magldr,repartition according the rom that you want to install.
Hello everybody, I tried your 2 last advices but nothing works. Any idea?
Read this:
http://forum.xda-developers.com/showthread.php?t=1251641
Don't have Sd card and sim card inserted while trying to fix it.
Try on other pc with windows, htc sync and windows Mobile device center installed.
Next thing, are you sure that you have HSPL and not SPL installed, its not same thing and task29 will not work.
Sent from my HD2 using xda premium
Thank you. I will try.