Was trying to install wp7 on my hd2, but now im stucked on magldr version 1.13. Forgot that the volume buttons doesnt work and i cant get the phone out of there. Try to load original rom or even task 29 but nothing becuase the pc doesnt recognize it. When the phone its booting it says something like cant boot from sd android kernel fail and then the menu and i can select only the first 1 boot wph.
Is there a way to get the phone out of there, or my only hope its to repair the volume button.
thanks
If you haven't been able to flash anything then as long as you just reboot your phone you'll just go back to whatever ROM you had previously
I have the same problem, after having upgraded to 1.13. Whenever i try to install a NAND version of Android, i am stuck with the splashscreen of the build i am trying to boot into. Bear in mind that every ROM i flash is flashed without any problems. So I guess it is not the NAND memory thats broken or faulty. The only build i am capable of running, is DFT's WP7 stock build. This loads perfectly, but due to the battery drain i would VERY much like to get rid of it and use my beloved MDJs Gingerbread/CM7 2.6 build.
To avoid any trouble i thought of just flashing a Task29, and a stock WM65 ROM to 'reset' to stock, that is, installing a custom ROM from SD card, so SPL is restored to factory version. However, i am not able to enter bootloader mode on my HD2. It can only boot into Magldr and succ. WP7. It doesn't help to press vol down, and it is not broken as I can use it in WP7. It seems as though HSPL is skipped and the phone is boot directly into magldr. This should NOT happen.
Anyways, this is very much close to a bricked device for me, so i am very sad these days. Does ANYONE know a trick that would enable me to replace magldr 1.13 with the working 1.12 without the tri-colour bootscreen of spl?
i remove the battery but when the hd2 start again it boots instantly to magldr, i need another way to flash it different to the three color screen (i cant get there becuase the volume down button its broke).
i have a problem like that
If your volume keys don't work, then there is seriously, no other way. You can't get into bootloader mode without the volume keys, and the you can't flash a different rom without the volume keys, so yeah, your device is pretty much bricked....
But IF the vol. down key works, I assume that it is something with MAGLDR or HSPL, or possibly an error in RAM. Are there anything that can be flashed via magldr that checks the state of underlying HSPL?
any fix to this??? same issue following the steps and volume buttons dont work. I can select the boot wph ....wph not installed
Maybe I'm tired or too old... but I don't understand your questions
You can imagine the different "softs" as layers:
1st: HSPL (or SPL) - it's the one you enter by pressing vol-down while booting.
this one give you the ability to flah a WM ROM (original or custom), a radio or MAGLDR
So if vol-down if dead... your phone also
nb: the first splash screen is at this level, so it will be still here after flash of MAGDR, CWM, NAND, WM7...
2nd: MAGLDR - it's the one you go in by pressing "end call" while booting.
It gives the ability to flash a NAND or WM7 via DFT
So if "end call" is dead... you're not But it's anoying I think...
3rd: CWM - it's the one you go in by selecting "AD recovery" in MAGLDR
It gives you the ability to flash a "CWM NAND" or an update... It also gives the ability to backup/restore a NAND.
So please clarify your question if you need help. More important do not post different problem by saying "same here". It's just confusing. Even if you can't boot your NAND it's not always the same problem
Let's try again dudes
osugsxr said:
any fix to this??? same issue following the steps and volume buttons dont work. I can select the boot wph ....wph not installed
Click to expand...
Click to collapse
HTC after sales... or few bucks
That is what I'm thinking, will try warranty to see if that works if not not ill see what they charge. For now back to the nexus s.
truc007 said:
HTC after sales... or few bucks
Click to expand...
Click to collapse
Sent from my Nexus S using XDA App
This is the answer to your problem if it does work find someone that is not a noob and have them fix your phone its really not that hard
Ok guys please help me I don't wanna start new thread
I installed on my hd2:
-HSPL 2.08
-Radio 2.15.50.14
-Magldr 1.13
-CMR
First of all I noticed that I dont have to hold the power button to get into the magldr menu.
I couldn't get into Boot As SD so I wanted to flash custom rom from bootloader. Unfortunately I can't do that. Even tried HR. Is there any solution to flash stock ROM
Any help would be greatly appreciated
Stuck for me too
I just flashed the latest hspl3, radio code and MAGLDR 1.13.
When I try to boot MCCM 4.5 from SD it hangs on the main Android Home Screen. When I try to boot WPH MAGLDR says that WPH is not installed.
I am still running Windows Mobile 6.5.
Any help would be greatly appreciated.
hi, have u tryed with the small button under the volume down button? it works as the volume down button...
If u can go in bootloader (if ur volume down works) could be ur nand is corrupted (as mine ) so bye bye hd2... i m waiting for the htc sensation
DAF doesnt' work
ChitownWingMan said:
I just flashed the latest hspl3, radio code and MAGLDR 1.13.
When I try to boot MCCM 4.5 from SD it hangs on the main Android Home Screen. When I try to boot WPH MAGLDR says that WPH is not installed.
I am still running Windows Mobile 6.5.
Any help would be greatly appreciated.
Click to expand...
Click to collapse
I figured out the Android problem (I needed a different rootfs).
I have magldr 1.13 working!!!!
However, when I try to run DAF I get the same:
"An error has occurred
Read below for more information
Error Description: Config load failed.
Info: .\RSPL\RSPL.cpp (725)
Error Description: CONFIG: can't open config file
Info: .\RSPL\RSPL.cpp (304)"
error that I have seen all over XDA-Dev.
However, none of the fixes I have seen on here have worked. I am running Windows 7 Professional.
I have tried:
Disabling Use USB in the Window Mobile Device Center
I have tried ANDR_INSTALL
I have rebooted
I have tried deleting all of the unattached USB device in the device manager.
I have tried using LeoAdvancedRUU
I have tried starting DAF first and then connecting the usb cable
I have tried connecting the USB cable first and then the starting DAF.
Help please!!! I was up until 8:30 AM trying to get this to work (I started at about 10:00 PM).
i also put the hd2 into the freezer for 10 minutes to solve heat problem and it doesn't start bootloaderi...
the nand corrupted..it start magdle but don't start android or cwm..there is nothing to do
tser04 said:
I have the same problem, after having upgraded to 1.13. Whenever i try to install a NAND version of Android, i am stuck with the splashscreen of the build i am trying to boot into. Bear in mind that every ROM i flash is flashed without any problems. So I guess it is not the NAND memory thats broken or faulty. The only build i am capable of running, is DFT's WP7 stock build. This loads perfectly, but due to the battery drain i would VERY much like to get rid of it and use my beloved MDJs Gingerbread/CM7 2.6 build.
To avoid any trouble i thought of just flashing a Task29, and a stock WM65 ROM to 'reset' to stock, that is, installing a custom ROM from SD card, so SPL is restored to factory version. However, i am not able to enter bootloader mode on my HD2. It can only boot into Magldr and succ. WP7. It doesn't help to press vol down, and it is not broken as I can use it in WP7. It seems as though HSPL is skipped and the phone is boot directly into magldr. This should NOT happen.
Anyways, this is very much close to a bricked device for me, so i am very sad these days. Does ANYONE know a trick that would enable me to replace magldr 1.13 with the working 1.12 without the tri-colour bootscreen of spl?
Click to expand...
Click to collapse
I have the same exact problem !! WP7 is the only OS that works and I want android
also the volume down key works...should I try to reflash HSPL ?? will that work ?? since HSPL 2.08 is already installed !??
Happen error
Read below for more information
Error Description: Config load failed.
Info: .\RSPL\RSPL.cpp (712)
Error Description: CONFIG: can't open config file
Info: .\RSPL\RSPL.cpp (291)
Related
oh i got a serious problem
after I install MAGLDR 1.11 my HD2 it succeed and did reboot and then it did stuck in white screen with hTC green log.
What to do? It cannot connect it to the sync with computer when it is with this screen. I tried so many time to reset it (with pressing long the power bottom) but I didn’t get MAGLDR 1.11 boot menu, so I cannot proceed to the next step which is installing NAND
My HTD looks like with no operating system only with white screen with hTC green log, What to do? Any help PlZzZzZzZzZzzzz?
Milan Geek said:
oh i got a serious problem
after I install MAGLDR 1.11 my HD2 it succeed and did reboot and then it did stuck in white screen with hTC green log.
What to do? It cannot connect it to the sync with computer when it is with this screen. I tried so many time to reset it (with pressing long the power bottom) but I didn’t get MAGLDR 1.11 boot menu, so I cannot proceed to the next step which is installing NAND
My HTD looks like with no operating system only with white screen with hTC green log, What to do? Any help PlZzZzZzZzZzzzz?
Click to expand...
Click to collapse
Did you try reading the flashing instructions. Refer to the Flashing NAND Android rom link in my signature. The problem is that you probably have the wrong radio. Also please don't start new threads to ask questions when threads already exist. This thread will soon be moved.
Milan Geek said:
oh i got a serious problem
after I install MAGLDR 1.11 my HD2 it succeed and did reboot and then it did stuck in white screen with hTC green log.
What to do? It cannot connect it to the sync with computer when it is with this screen. I tried so many time to reset it (with pressing long the power bottom) but I didn’t get MAGLDR 1.11 boot menu, so I cannot proceed to the next step which is installing NAND
My HTD looks like with no operating system only with white screen with hTC green log, What to do? Any help PlZzZzZzZzZzzzz?
Click to expand...
Click to collapse
remove battery
enter HSPL via bootloader (have you got HSPL 2.08)??
(long press volume down + briefly press power button)
btw wrong post here mate
Moved to HD2 Android Q&A and General
I got the same problem with SPL 2.08.HSPL, oficial ROM 3.14.412.2, RADIO 2.15.50.14. I've tried everything, wasting tons of hours, reinstaling diferent versions of MAGLDR and so, but unfortunatelly I've had to back to the oficial ROM.
Help Please!
sanroman said:
I got the same problem with HSPL 2.08, oficial ROM 3.14.412.2, RADIO 2.15.50.14. I've tried everything, wasting tons of hours, reinstaling diferent versions of MAGLDR and so, but unfortunatelly I've had to back to the oficial ROM.
Help Please!
Click to expand...
Click to collapse
Are you sure your spl version is 2.08.hspl and NOT 2.08.0000?
Completly!. SPL-2.08.HSPL as stated on tricolor screen. Thanks for the response.
And you also sure of the radio version? Really strange that it doesn't work. Where exactly does it get stuck, is it after or during the install of magldr?
Absolutely sure. All info is the one shown in the device. MAGDLR installs perfectly at 100%, it stucks at reboot, it shows the white htc screen and that's all, the device doen't work any more and I've to reinstall oficial rom.
Really weird - first one I've seen where 2.08.hspl and 2.15.50 radio doesn't get magldr to boot. Not sure what else to suggest apart from perhaps doing a Task29 to format the NAND area and starting all over.
I've tried one again, including task29 at begining. And i'm still the same, MAGLDR doesn't show the menu and stucks at login htc screen. I want to cry!. I'd appreciate any idea. All DFT needs MAGDLR, I need smthing that doesn´t need MAGDLR, is it possible?.
There are the Android versions that run off sd card which run as a dual boot with winmo.
sanroman said:
I've tried one again, including task29 at begining. And i'm still the same, MAGLDR doesn't show the menu and stucks at login htc screen. I want to cry!. I'd appreciate any idea. All DFT needs MAGDLR, I need smthing that doesn´t need MAGDLR, is it possible?.
Click to expand...
Click to collapse
Check your radio version - I had the same issue but after updating my radio everything was fine!
sanroman said:
I've tried one again, including task29 at begining. And i'm still the same, MAGLDR doesn't show the menu and stucks at login htc screen. I want to cry!. I'd appreciate any idea. All DFT needs MAGDLR, I need smthing that doesn´t need MAGDLR, is it possible?.
Click to expand...
Click to collapse
well, maybe its kinda "stupid" question, but do you press the power (red) button while booting? I mean, you have to press it long enough, till the magldr menu comes up..
Believe me that i've tested that way, and another ones, so as to get it work, but no luck.
I got stuck on the htc logo screen while trying to boot to a previous NAND version I had. I flashed it right away for the first time but now I jsut got stuck on the logo screen an than its reboots, again and again. any help as now I stuck with the MJD CyanogenMod which I have few problams with and I am trying to boot again to hd2one CyanogenMod .
mikelt89 said:
I got stuck on the htc logo screen while trying to boot to a previous NAND version I had. I flashed it right away for the first time but now I jsut got stuck on the logo screen an than its reboots, again and again. any help as now I stuck with the MJD CyanogenMod which I have few problams with and I am trying to boot again to hd2one CyanogenMod .
Click to expand...
Click to collapse
Format the sd card. I would also suggest flashing back to a winmo rom and then starting over.
chpelle said:
Check your radio version - I had the same issue but after updating my radio everything was fine!
Click to expand...
Click to collapse
Rerereinstalled and no luck. Why me?
I have the same problem. I have checked the radio and everything to make sure it is fine but still getting stuck at htc screen??
Can someone help me please
Thanks
cwm recovery
flashed cwm recovery update for hd2 no my phone wont charge nor register when plugged into the computer. is there a way to fix this
hi,
MAGLDR doesn't recognize my sd card . i can't use usb mass storage , AD SD => CWM . apparently all the roms i want are released az ZIPs ...
is there a fix for that ?
Are you using magldr 1.13? If so you need to use the new CWM 1.3 partitions which now installs the partition onto NAND, so to use CWM you need to boot into the AD Recovery option from menu and not Boot AD SD. There is also no need to copy files to root of sd card.
There is a problem with magldr usb mass storage, but if you boot to CWM, select mount and storage and the usb storage you can copy perfectly.
hi
my problem is with the bootloader screen. After installing magldr 1.13 i could not start the ppc in bootloader mode. i have tried many key combinations and etc.. but it is still starting with magldr after a short white htc screen. So now i cannot load any official or custom winmo firmware. None of the android nand fw are working. Now i only can use winphone 7 with limited abilities.. Can anyone tell me the way to solve this and go back to original rom?
thanks
exxx80 said:
hi
my problem is with the bootloader screen. After installing magldr 1.13 i could not start the ppc in bootloader mode. i have tried many key combinations and etc.. but it is still starting with magldr after a short white htc screen. So now i cannot load any official or custom winmo firmware. None of the android nand fw are working. Now i only can use winphone 7 with limited abilities.. Can anyone tell me the way to solve this and go back to original rom?
thanks
Click to expand...
Click to collapse
When you say you can not start in bootloader, bootloader is started by turning the phone off, holding in the vol down button only and turning on the phone.
The phone should not even get to the white htc screen.
If you get into the tri-colour screen you can get back to a stock rom to start again.
waspsl said:
When you say you can not start in bootloader, bootloader is started by turning the phone off, holding in the vol down button only and turning on the phone.
The phone should not even get to the white htc screen.
If you get into the tri-colour screen you can get back to a stock rom to start again.
Click to expand...
Click to collapse
Yes exactly thats what i m doing. But it passes to magldr. I even have reset from the red button at the back but no way to bootloader
@ClydeB1 : so i have to install the new CWM using the USB Flasher and it'll boot from AD Recovery ? thats good news i guess ...
will it let me install ZIP roms ? also i have a 512Leo . why would i (or anyone) want to partition NAND ?!?
MTN_HD2 said:
@ClydeB1 : so i have to install the new CWM using the USB Flasher and it'll boot from AD Recovery ? thats good news i guess ...
will it let me install ZIP roms ? also i have a 512Leo . why would i (or anyone) want to partition NAND ?!?
Click to expand...
Click to collapse
Yes, install the appropriate cwm partition by going to usb flasher and running daf.exe. Then the phone will reboot to magldr, select AD recovery and you can then flash zip roms or updates, backup etc etc etc.... I have a 512 device also, so no problems.
I guess one of the reasons for running recovery off NAND is that not all users could get the sd based recovery to work.
exxx80 said:
hi
my problem is with the bootloader screen. After installing magldr 1.13 i could not start the ppc in bootloader mode. i have tried many key combinations and etc.. but it is still starting with magldr after a short white htc screen. So now i cannot load any official or custom winmo firmware. None of the android nand fw are working. Now i only can use winphone 7 with limited abilities.. Can anyone tell me the way to solve this and go back to original rom?
thanks
Click to expand...
Click to collapse
I have the same problem here. I tried to return from my NAND Android Builts to a Windows 6.5 ROM. But after Flashing, the reboot got stuck at the logo. I tried flashing over and over again, different WinRoms, reflashed MAGLDR and even tried a combination with HSPL. nothing seems to work. I dont pass the logo, cannot enter MAGLDR or load a normal build. I kinda run out of all my magic. anyone got any suggestions?
fastscorpion2010 said:
I have the same problem here. I tried to return from my NAND Android Builts to a Windows 6.5 ROM. But after Flashing, the reboot got stuck at the logo. I tried flashing over and over again, different WinRoms, reflashed MAGLDR and even tried a combination with HSPL. nothing seems to work. I dont pass the logo, cannot enter MAGLDR or load a normal build. I kinda run out of all my magic. anyone got any suggestions?
Click to expand...
Click to collapse
What hspl version and radio are you using? To use magldr you need 2.08.hspl and radio 2.08.50.xx or higher .50 radio
I'm not sure why it would hang on reflash to winmo, but let's try get to Android.
Hi!
I am using the SPL 2.08 and When i am installing the MAGLDR111 or MAGLDR113 it's Stop in 0%
How i can install the MAGLDR?
grisantycosme said:
Hi!
I am using the SPL 2.08 and When i am installing the MAGLDR111 or MAGLDR113 it's Stop in 0%
How i can install the MAGLDR?
Click to expand...
Click to collapse
you're using Stock SPL, you need Hard SPL (HSPL)
ClydeB1 said:
Are you using magldr 1.13? If so you need to use the new CWM 1.3 partitions which now installs the partition onto NAND, so to use CWM you need to boot into the AD Recovery option from menu and not Boot AD SD. There is also no need to copy files to root of sd card.
There is a problem with magldr usb mass storage, but if you boot to CWM, select mount and storage and the usb storage you can copy perfectly.
Click to expand...
Click to collapse
You...so...rock!
I've been getting utterly frustrated with watching Windows bars filling only halfway, but your solution worked like a charm!
:good: x many!
magldr problem
hi
i was instaling the magldr on my htc hd2, but during the instalation i realise that my VOLUME UP and DOWN buttons are broken and dont work...i have to choose some option in MAGLDR but i cant...so i'm stuck here, my phone boots only MAGLDR even when i restart the phone from the red button, or even when i pull out the batery...is there some option to turn off the magldr, without using the volume buttons? please help me..in the store workers tell me that they cant fix the broken volume buttons...and now i cant use my phone... cheers...
Hey guys,
currently I´m trying to flash Android NAND on a HD2.
Apparently there are some problems with the bootloader.
I tried two different ways, which are explained in this thread:
http://forum.xda-developers.com/showthread.php?t=905060
First I tried to install MAGLDR 1.13. Here is the problem that MAGLDR 1.13 seems not to be properly installed because the phone wont boot in the MAGLDR bootloader. It just hangs at the green/white HTC bootscreen.
As second method I tried to flash cLK 1.4. Here the bootloader seems to be installed properly but it´s not possible to install the ClockworkMod Recovery. Every time I start the batch file it hangs on "waiting for device".
Since I tried some things I only can boot into the bootloader and no longer load Windows.
I´ve installed the latest radio (Radio Leo 2.15.50.14) and HSPL (3.03).
Any ideas what I can do know?
when you install magldr it wipes windows off the deivce, you are aware of that?
when you start the device with magldr you need to hold the power off button til you get the menu up then you can use the usb flasher if it is a daf installer or you need to install CWM recovery and install a rom that way
either way windows will no longer be on your device
Yeah I know this. But the problem is that the magldr bootloader is not booting. It hangs on the white HTC screen. Without any other reaction.
matze91 said:
Yeah I know this. But the problem is that the magldr bootloader is not booting. It hangs on the white HTC screen. Without any other reaction.
Click to expand...
Click to collapse
what version of android did you install? you need HSPL 2.08 or it will not work anways
if all you done was install magldr without install anything else it will do exactly as you have described because there is nothing for it to load up
I think you misunderstood me
Normally if magldr was installed correctly I should see a screen like this (http://www.xda-developers.com/wp-content/uploads/2011/02/MAGLDR-boot-menu.jpg), when I boot with hold power button+left arrow key.
But when I press this combination it does not boot to this screen. It just does nothing. And this is why I can´t proceed with any instruction, because I need a working magldr.
matze91 said:
Hey guys,
currently I´m trying to flash Android NAND on a HD2.
Apparently there are some problems with the bootloader.
I tried two different ways, which are explained in this thread:
http://forum.xda-developers.com/showthread.php?t=905060
First I tried to install MAGLDR 1.13. Here is the problem that MAGLDR 1.13 seems not to be properly installed because the phone wont boot in the MAGLDR bootloader. It just hangs at the green/white HTC bootscreen.
As second method I tried to flash cLK 1.4. Here the bootloader seems to be installed properly but it´s not possible to install the ClockworkMod Recovery. Every time I start the batch file it hangs on "waiting for device".
Since I tried some things I only can boot into the bootloader and no longer load Windows.
I´ve installed the latest radio (Radio Leo 2.15.50.14) and HSPL (3.03).
Any ideas what I can do know?
Click to expand...
Click to collapse
I'm new to all this too so bare with me.
I think you may have installed the wrong HSPL. This is from the HSPL thread.
Android / WP7 / MAGLDR don't support HSPL3.03/OSPL3.03.
You need HSPL2.08 to run Android / WP7 / MAGLDR
When you installed HSPL you chose the wrong option. Someone more knowlegable will hopefully come along and tell you how to fix it.
After destroying and downgrading of HSPL with an original HTC Win Rom I could install a new HSPL again...
Don´t ask me how I´ve done this, but it worked
So thanks to all!
So i tried flashing an android ROM but its stuck on the AD recovery go go go screen.
I also wanna task 29 but I don't know how to get to the bootloader from MAGLDR 1.3
someone help please !
ummm i dunno if magldr can switch you into the bootloader, but doesn't the regular way to get to the bootloader work?
regular way:
1. make sure phone is OFF...take out the battery and plug it back in to make sure
2. hold down the volume down button
3. tap the power/end call button to power on the device
4. keep holding down volume down button
...bootloader should appear!
i guess you are a senior member so you must be looking for something else, it can't be as simple as above, is it?
ASCIIker said:
ummm i dunno if magldr can switch you into the bootloader, but doesn't the regular way to get to the bootloader work?
regular way:
1. make sure phone is OFF...take out the battery and plug it back in to make sure
2. hold down the volume down button
3. tap the power/end call button to power on the device
4. keep holding down volume down button
...bootloader should appear!
i guess you are a senior member so you must be looking for something else, it can't be as simple as above, is it?
Click to expand...
Click to collapse
i tried that...despite it...it goes to the MAGLDR menu
and USB flasher keeps saying WAIT USB !!
basically I am stuck in MAGLDR
someone please help
i downloaded HD2 NAND kit...
and was ablt to reformat the Magldr Partition...
that time somehow the USB flasher seems to work,,,
however for every other function...it fails...like task 29 etc..
i am really confused and don't know what to do !!
backlashsid said:
someone please help
i downloaded HD2 NAND kit...
and was ablt to reformat the Magldr Partition...
that time somehow the USB flasher seems to work,,,
however for every other function...it fails...like task 29 etc..
i am really confused and don't know what to do !!
Click to expand...
Click to collapse
Mate,
how about flashing stock rom via SD? dont use your old sd, get the new one, and try to flash the stock rom.
If you can pass that, then you can go back to try magldr again
or else,
I think it may be a hardware issue related, may be the volume down button is damaged. If this the case, since you are in android nand, you cant flash stock rom from USB sync
I hope that is not the case though
goodluck
silverwind said:
Mate,
how about flashing stock rom via SD? dont use your old sd, get the new one, and try to flash the stock rom.
If you can pass that, then you can go back to try magldr again
or else,
I think it may be a hardware issue related, may be the volume down button is damaged. If this the case, since you are in android nand, you cant flash stock rom from USB sync
I hope that is not the case though
goodluck
Click to expand...
Click to collapse
surprisingly the VOL DOWN key is not at all damaged..
cos in the magldr menu I am able to go down and choose USB Flasher
I tried to install the DESIRE STOCK NAND ROM by clicking on DDAF and it worked
howerver the ROM got stuck at the DFT logo
ALso I am not at all able to get to the bootloader screen !! any ideas what to do ??? i guess flashing via SD wont work if I cant get to the bootloader
EDIT: I am able to install DAF.exe type ROMS...just installed Windows Phone 7 works...but the problem still is me wanting android and preferably at a time the old win mo...and without bootloader dont know what to do !! Help
backlashsid said:
surprisingly the VOL DOWN key is not at all damaged..
cos in the magldr menu I am able to go down and choose USB Flasher
I tried to install the DESIRE STOCK NAND ROM by clicking on DDAF and it worked
howerver the ROM got stuck at the DFT logo
ALso I am not at all able to get to the bootloader screen !! any ideas what to do ??? i guess flashing via SD wont work if I cant get to the bootloader
EDIT: I am able to install DAF.exe type ROMS...just installed Windows Phone 7 works...but the problem still is me wanting android and preferably at a time the old win mo...and without bootloader dont know what to do !! Help
Click to expand...
Click to collapse
Hey blackashsid, sorry to hear you are having troubles. Without being able to get to the SPL bootloader you will not be able to flash any .nbh file to your HD2. This translates to you not being able to flash a Windows Mobile ROM stock or custom, a different radio version, splash screen, any HSPL or SPL, or cLK. And yes flashing via SD card is no good to you without the SPL bootloader.
Option #5 USB Flasher in MAGLDR will only flash CWM or A DAF ROM.
Your issue is somewhat strange to me, I really don't understand why you are having this issuer unless it is hardware related.
T-Macgnolia said:
Hey blackashsid, sorry to hear you are having troubles. Without being able to get to the SPL bootloader you will not be able to flash any .nbh file to your HD2. This translates to you not being able to flash a Windows Mobile ROM stock or custom, a different radio version, splash screen, any HSPL or SPL, or cLK. And yes flashing via SD card is no good to you without the SPL bootloader.
Option #5 USB Flasher in MAGLDR will only flash CWM or A DAF ROM.
Your issue is somewhat strange to me, I really don't understand why you are having this issuer unless it is hardware related.
Click to expand...
Click to collapse
yeah its strange !
its like i am stuck with MAGLDR
and ders no way to uninstall it or to get to the bootloader for a WM ROM !!
any ideas what is causing this ??
i will really appreciate it !
EDIT: also i noticed all of my DAF ANdroid ROMS get stuck at the splash screen...only WP7 made it !! i want android !
any reason why this happend ?
if you installed wp7 then it isnt an issue wth the phone, its quite possible the roms you are trying to install
Download again the rom you want to use... and make sure you read installing process - every android rom has his specific installing process - clockwork , ext3 ,ex4 etc etc.
I hope you solve your prolem
ubejd said:
Download again the rom you want to use... and make sure you read installing process - every android rom has his specific installing process - clockwork , ext3 ,ex4 etc etc.
I hope you solve your prolem
Click to expand...
Click to collapse
i did ! man...nothing works...its like i am stuck with Magldr !! can do nothing !
Ok im now in a proper mess.
Ok ive been battling with trying to get Android on my HD2 i have manged no prob with the MAGLDR in the past but wanted to change to the CLK version.
I tried all the tried the tips etc and have downloaded the HD2 Android Nand Toolkit but i just couldnt get it working. Once i thought i did I get CLK wokring I installed the ZIP file but it just got stuck on the HTC splash screen. The only way i can it to actually boot is to put the stock Winmo ROM back on. So at the moment I have the stock ROM just with SPL. As soon as i run the Task29 option in the toolkit it then fails to load. Could somebody please advise me on what to do.
TommyHD2 said:
Ok im now in a proper mess.
Ok ive been battling with trying to get Android on my HD2 i have manged no prob with the MAGLDR in the past but wanted to change to the CLK version.
I tried all the tried the tips etc and have downloaded the HD2 Android Nand Toolkit but i just couldnt get it working. Once i thought i did I get CLK wokring I installed the ZIP file but it just got stuck on the HTC splash screen. The only way i can it to actually boot is to put the stock Winmo ROM back on. So at the moment I have the stock ROM just with SPL. As soon as i run the Task29 option in the toolkit it then fails to load. Could somebody please advise me on what to do.
Click to expand...
Click to collapse
You need Hardspl from Cotulla. Search through the threads you'll find it. but if you had magldr installed you should have all the the necesary elements. using the tool kit you have to hold the volume down than power on. wait for your phone to say usb. Than proceed to task 29. Than when the screen shuts off hold the volume down again before the screen comes on. Pick your partition size, Than hit the partiton button wait for it to do its thing than hold the back key and some text should come on your phone ending with something like fastboot commands suspend. Flash the recovery. than when it go off again hold home until you get in to recovery. Hope that helps.
Cheers for the help. Ive got as far as the revovery install i had a load of text on the screen the last line of wich is 2690 --Portchange-- and the pc is sitting on waiting for device.
also this is all it does when i turn the phone on now
TommyHD2 said:
also this is all it does when i turn the phone on now
Click to expand...
Click to collapse
Are you holding the back button until the text comes on?
Have you successful installed hspl? Successfully installed magldr and successfully installed cwm?
Is the Rom your installing a magldr version? Did you get it from the Android nand thread?
Is your SD card working is it formatted to fat32?
Are you installing the Rom from SD?
Is it a .zip file?
Edit/ oh clk..... lol never used it
Sent from my HTC HD2 using XDA Premium App
If i hold the power with the back button or the power/hangup button the text goes up to --portchange-- line if i hold the home button it shoes the line
GET STALL_DESCRIPTOR 128 6 1536 0 10
Pc is still saying waiting for device.
I have magldr but cant seem to boot to it and i have SPL-2.08.HSPL CotullaHSPL
I also tried to install magldr again and it gives a USB init failed Info \\rspl\rspl..cpp (736) but the phone is showing USB with the red\green\blue\white screen.
whynot66 said:
Have you successful installed hspl? Successfully installed magldr and successfully installed cwm?
Is the Rom your installing a magldr version? Did you get it from the Android nand thread?
Is your SD card working is it formatted to fat32?
Are you installing the Rom from SD?
Is it a .zip file?
Edit/ oh clk..... lol never used it
Sent from my HTC HD2 using XDA Premium App
Click to expand...
Click to collapse
haha..
TommyHD2 said:
Ok im now in a proper mess.
Ok ive been battling with trying to get Android on my HD2 i have manged no prob with the MAGLDR in the past but wanted to change to the CLK version.
I tried all the tried the tips etc and have downloaded the HD2 Android Nand Toolkit but i just couldnt get it working. Once i thought i did I get CLK wokring I installed the ZIP file but it just got stuck on the HTC splash screen. The only way i can it to actually boot is to put the stock Winmo ROM back on. So at the moment I have the stock ROM just with SPL. As soon as i run the Task29 option in the toolkit it then fails to load. Could somebody please advise me on what to do.
Click to expand...
Click to collapse
alls ye really need mate if you have flashed spl 2.08 or above is get task29 plug phone via USB turn phone off turn back on while holding vol down key untill tri colours appear then it says USB at bottem, run task29 from computer phone will do the rest, get magldr go back to tri colour with USB at bottem run ROMUpdateUtility install it then try the rom in my signature first typhoon and download the recovery of his page and install that specific one then flash your rom, its got installation on typhoon thread....
Cheers for the help. Ive re-installed MAGLDR and have ClockworkMOD recovery v3.0.0.5 working and I have a rom that i have downloaded and am currently downloading one of yours Laney, before i do anything clockwork MOD is showing "Failed to find Cache partition to mount at \cache.
Dont you have an sd card inserted?