Hi everybody;
I know this matter has been discussed b4 here in the forum but in fact i'm confused and have not found any way for WM phones.In this case my phone is ARTE100,i hope you'd help me get out of this like u've done many times before
This phone stucks on HTC logo and won't go to bootlaoder menu as well.
Thanks in advance.
saratel-gsm said:
Hi everybody;
I know this matter has been discussed b4 here in the forum but in fact i'm confused and have not found any way for WM phones.In this case my phone is ARTE100,i hope you'd help me get out of this like u've done many times before
This phone stucks on HTC logo and won't go to bootlaoder menu as well.
Thanks in advance.
Click to expand...
Click to collapse
you should do is To perform a hard reset device Hard reset Soft reset
Press and hold the Left SOFT KEY and the Right SOFT KEY, and at the same time, use the stylus to press the RESET button at the lower left side of your device.
Release the stylus, but continue pressing the two soft key buttons. Release them only when you see the following message on your device screen: “Press Send to restore manufacturer default, or press other keys to cancel.“
Press on your device. Warning! Your device will be set back to factory default settings. Please ensure any additional installed programs and/or user data have been backed up before a hard reset is performed.
about the gold card, for more details you can see it in -> http://psas.revskills.de/
...
gold card is just the correct original rom on the micro sd.
to make a gold card:
1.download your correct original rom
2.put it on your micro sd
3.rename the .NBH to Arteimg.nbh
4.put it into your device and enable bootloader
Rn
raving_nanza said:
gold card is just the correct original rom on the micro sd.
to make a gold card:
1.download your correct original rom
2.put it on your micro sd
3.rename the .NBH to Arteimg.nbh
4.put it into your device and enable bootloader
Rn
Click to expand...
Click to collapse
what you've never tried it ..?
and how the results...??
the success you get a gold card, Raving ..?
my post was how to make a gold card and advice to ''saratel-gsm'' on what a gold card actually is..
Hakim Rahman said:
what you've never tried it ..?
Click to expand...
Click to collapse
*of course i have tried it, i posted how to make a gold card
Hakim Rahman said:
and how the results...??
Click to expand...
Click to collapse
*im not exactly sure what your asking dude, please explain?
Hakim Rahman said:
the success you get a gold card, Raving ..?
Click to expand...
Click to collapse
* again, im not exactly sure what your asking dude, please explain?
raving_nanza said:
my post was how to make a gold card and advice to ''saratel-gsm'' on what a gold card actually is..
*of course i have tried it, i posted how to make a gold card
*im not exactly sure what your asking dude, please explain?
* again, im not exactly sure what your asking dude, please explain?
Click to expand...
Click to collapse
forget it ...!! I just want to know if you managed to get a gold card ....
Hakim Rahman said:
I just want to know if you managed to get a gold card.
Click to expand...
Click to collapse
sorry Hakim, i was not sure what you meant..
well, anyway.. that is how you make a gold card from scratch..
i have noticed you help alot on the artemis forum.. keep up the good work dude, it makes Neo's job a lot easier for him and im sure he appreciates all the help
* iv added how to make gold card to the tips&tricks thread..
saratel-gsm - click on the tips&tricks thread, you will need to look for the "Bricked Device" post.
ill ask Neo to close this thread now, i think its safe to say the OP question is solved..
Rn
Related
My MDA was unable to get back to bootload after a unsuccessful ROM upgrading. Is it possible to replace the ROM (hardware) so that I can save my MDA?
I tried the Power on key and softreset to reset it but only return to a messive screen.
Pls help. Thanks
cris...
you dont need to replace the hardware rom!!
try runing the upgrade program again, it sometimes picks up where it left off. if that dont work, try the SD card method.
i'd go into more details, but all that info is here in these forums already.
if u still need help though, contact me, and i'll try to help you.
good luck
Dear Ntabikha,
Thanks v much!
However, I tried the upgrade program many times and the decktop just said the computer cannot recognise the device.
So, I think method 1 is not possible.
For method two, I will try to put the nk.nbf file into my SD card and put it in the device and see whether the MDA can pick up the ROM. Will let you know whether it is successful.
BTW, when the screen is on, it only appears some fuzzy horizontal lines and two small empty boxes, have you seen this before?
Chris
yes, i had the same fuzzy lines. i fixed That problem via the SD card method.
just remember that, you have to write the nbf file to SD card, not just copy it to SD card
dont laugh, i did that mistake at first
good luck
How can I "write" it to the card?
I thought I only copy the file to the card through a SD reader.
Well, I know now, use rom kitchen to cook the rom and use osimagetool to copy the nb1 file into a sd card.
All i need to do next is to insert into the MDA and press power button together with softreset key for several times until successful....
Dear ntabikha,
I am still unable to obtain the bootloading screen of my MDA after inserting the SD with nb1 file written by xdatool. I tried many times power button and soft reset simultaneously (more than 20times) and the screen are still full of messy lines and 2 big empty boxes.
Can you help please? What is the fix broken bootloader in the xdatool?
I really did search around the forum but still can't be able to get back the bootloader screen. Pls help.
Chris
ntabikha said:
yes, i had the same fuzzy lines. i fixed That problem via the SD card method.
just remember that, you have to write the nbf file to SD card, not just copy it to SD card
dont laugh, i did that mistake at first
good luck
Click to expand...
Click to collapse
I'm wondering if you could not see bootloading screen , how could you use SD card to restore OS and bootloader ?
No, there is no bootloading screen at all.
I took the MDA out to a repair shop and they said that is a hardware failure. And they don't have the stock to replace it.
But I don't believe that cause I was just downloading the OS. It shouldn't hurt the hardware that much.....
chris_khho said:
BTW, when the screen is on, it only appears some fuzzy horizontal lines and two small empty boxes, have you seen this before?
Chris
Click to expand...
Click to collapse
I fixed couple such phones "horizontal lines and two small empty boxes" due to failure upgrading (all flash ROM messed up).
You have to use hardware flash ROM writer to wire the flash ROM pin to write bootloader and CE directly to chip.
I can help you to fix the problem (I'm in Canada, my email is [email protected])
Hi, I have similar trouble. My boss upgrade his MDA TMO (Austria) to official TMO version of OS and now it coming only to splash screen. MDA doesn't sync through cradle, doesn't seems to be charged, and I cannot enter BOOT mode for flashing ROM from SD card.
Is there any chance to fix it by myself?
Thanx, Ivan
TO CGIGATE: If you have any solution, can you post it here? Or it is so dangerous for nonexpert people? :wink:
Ivan said:
Hi, I have similar trouble. My boss upgrade his MDA TMO (Austria) to official TMO version of OS and now it coming only to splash screen. MDA doesn't sync through cradle, doesn't seems to be charged, and I cannot enter BOOT mode for flashing ROM from SD card.
Is there any chance to fix it by myself?
Thanx, Ivan
TO CGIGATE: If you have any solution, can you post it here? Or it is so dangerous for nonexpert people? :wink:
Click to expand...
Click to collapse
If you don't have a working OS and a working bootloader, the only solution is hardware solution. You have to wire the flash chip directly to the flash ROM writer ...
yes, it is dangerous for nonexpert people
Thank you CGIGATE for quick answer. Anyway I wrote you an email, could you be so kind and send me informations how I can do that, or where I can find these steps?[/quote]
This is my 3rd time that I have met this situation again
My 3600 is not able to boot into the "today" screen while I turn on my 3600
It stops at the screen of " Windows mobile "
Apart from hard reset, any solutions?
thanks bro!!
matttse said:
This is my 3rd time that I have met this situation again
My 3600 is not able to boot into the "today" screen while I turn on my 3600
It stops at the screen of " Windows mobile "
Apart from hard reset, any solutions?
thanks bro!!
Click to expand...
Click to collapse
Try reflashing the ROM or switching ROMs.
I suppose you have HardSPL installed, it shouldn't be any problem!
In case you have any questions, please consult the Trinity Guides and the Wiki. There is also a Wiki page referring to SD Card flashing (my personal favorite which I recommend).
tnyynt said:
Try reflashing the ROM or switching ROMs.
I suppose you have HardSPL installed, it shouldn't be any problem!
In case you have any questions, please consult the Trinity Guides and the Wiki. There is also a Wiki page referring to SD Card flashing (my personal favorite which I recommend).
Click to expand...
Click to collapse
Thanks for your explanation. How can I get that file mentioned in "SD Card Flashing" Also, I haven't got Hard SPL
matttse said:
Thanks for your explanation. How can I get that file mentioned in "SD Card Flashing" Also, I haven't got Hard SPL
Click to expand...
Click to collapse
You find everything at the guides and Wiki I mentioned above!
Hi there,
I need to install hard SPL from the tri-color siutation. Therefore the installation should be performed by the use of SD-card.
I can read good guides on how to install hard spl through active sync, but not by the use of the SD card. Anybody who can help me?
Thank you.
Michel
This was a easy one to find. Please try the Search functions within this site. here is what I think you are looking for:
http://forum.xda-developers.com/showthread.php?t=384084&highlight=flash+SD
I allready saw that one, but it didn't work. I searched quite a lot. Nothing helped.
In the end, I found the solution (for anybody who has the same problem):
http://forum.xda-developers.com/showthread.php?t=403883&highlight=tri+color
Read it very well and do as it is said in the desciption (also read the 'sub-link'!!!).
Greetz,
Michel
bkeaver said:
This was a easy one to find. Please try the Search functions within this site. here is what I think you are looking for:
http://forum.xda-developers.com/showthread.php?t=384084&highlight=flash+SD
Click to expand...
Click to collapse
mewsijben said:
In the end, I found the solution (for anybody who has the same problem):
http://forum.xda-developers.com/showthread.php?t=403883&highlight=tri+color
Michel
Click to expand...
Click to collapse
I don't understand this post.
The question was: "How to install HardSPL from the micro-SDHC card"
This still isn't answered, only how to flash a ROM *.nbh file from the card, which we already knew.
So, the initial question - HardSPL from the card - remains in limbo ?
Later edit: unless it means that renaming HardSPL nbh file to POLAIMG.nbh and flashing off the card in Bootloader mode worked for someone ?
You can't install HardSPL from SD-card...
You need your device synchronized...read more this post
http://forum.xda-developers.com/showthread.php?t=375338
your PDA *MUST* be in WM and happily synced with the PC BEFORE running each new step.
Click to expand...
Click to collapse
cheers!
ouioui01 said:
You can't install HardSPL from SD-card...
Click to expand...
Click to collapse
That's my experience as well. WinXP is needed on the PC
Hi all,
I lost my XPERIA password and I have too many file on it, I can answer any income call, but I can not use of my divace
I had Tytn II before and I can back it when I lost password but with XPERIA I don't know what can I do, Please hellllllppppppppppp MeEeE
remove the microSD...back it up and Hard Reset the phone
if the files are on SD follow as above, if you have them on your Phone itself try itsutils to dump your complette rom !
then put it in kitchen unpack everything and voila the files should be there
EDIT: here the link how to back up your rom
http://forum.xda-developers.com/showthread.php?t=462926
if files on SD grad sd out of your X1 and hardreset it or just flash ROM again / do SEUS update
Greets
Thankssssss
Hi Guys,
thanks about your prompt reply, Great way, I did and now I have my phone again.
Thanks a lot
Just admit you stole/found someone's phone.
??
what did you mean?
orelsi said:
Just admit you stole/found someone's phone.
Click to expand...
Click to collapse
why would he care about the files then? hard reset is enough! bad things happen
anaadoul said:
why would he care about the files then? hard reset is enough! bad things happen
Click to expand...
Click to collapse
After emailing back and forth with the HTC support team about the Leo's "too loud ear piece" and after asking me a million questions they finally sent me the Debug tool 3.4 to run it in my Leo and send them the logfile.
Well the stupid application it's been running for days and never seems to stop. It did create some 20 DM files on my SD card which can't be seen in explorer anymore. I put it into a card reader to see what's happening.
I hard reseted my Leo to stop the debugging tool but no use, I reflashed, taken out the sd card, but nu use the darn thing still runs and kills my battery! WIFI doesn't work either!!!
What should I do?
Please help!!!
G
hard reset
The only solution that always works
funny but not helpful!
thimiost said:
The only solution that always works
Click to expand...
Click to collapse
If you have the answer just give it to me! Trust me I've searched every possible forum!
Regards,
G
wmfreak said:
If you have the answer just give it to me! Trust me I've searched every possible forum!
Regards,
G
Click to expand...
Click to collapse
you must read carefully it is hard reset
he just told you m8 perform a hard reset on the device
I guess nobody read my post!
evo6 said:
he just told you m8 perform a hard reset on the device
Click to expand...
Click to collapse
If look carefully it does say that I've hard reseted, reflashed with different rom including cooked rom but same problem!!!
any help?
regards,
G
Format Your sdcard. the file must be on there if youve reflashed
Done that too!
fards said:
Format Your sdcard. the file must be on there if youve reflashed
Click to expand...
Click to collapse
I even swapped SD cards, formatted them you name it I've done it!
Please share your wisdom if you have an answer!!!
PS debug tool 3.4 is what's causing the problem!
Are you doing a hard reset without your sd card inserted?..
If the answer is yes, then try..
format your sd card, then flash a new rom using goldcard method.... it is virtually impossible for the file to stay storaged in the sd (after format) or the device (beacuse u did format it when doing the flashing process).
In makes sense but!
doctorcete said:
Are you doing a hard reset without your sd card inserted?..
If the answer is yes, then try..
format your sd card, then flash a new rom using goldcard method.... it is virtually impossible for the file to stay storaged in the sd (after format) or the device (beacuse u did format it when doing the flashing process).
Click to expand...
Click to collapse
I've reflashed even without SD (upgrade ROM 1.48 from 1.43) and the stupid and the Htclog folder is still iin File explorer under MyDevice working hard at creatinf log files!!!
I've tried to rerun the stupid Debug tool 3.4 but it says "Fail to read MFG area (6)" all the time!
I'm desperate! Pls Help!!!
G
wmfreak said:
I've reflashed even without SD (upgrade ROM 1.48 from 1.43) and the stupid and the Htclog folder is still iin File explorer under MyDevice working hard at creatinf log files!!!
I've tried to rerun the stupid Debug tool 3.4 but it says "Fail to read MFG area (6)" all the time!
I'm desperate! Pls Help!!!
G
Click to expand...
Click to collapse
I know hard reset should have helped, but try letting the phone empty and then remove the battery for a couple of hours-day, then try it agian.
Mabey I don't get the question but.. how come it's still working with the debugging tool while the phone is flashed? The debugging tool is prob. placed on a special sector of the main memory normaly not accessed by a rom, the program it self doesn't run from normal memory sectors, so you might have a try with a SPL update/overwright. If all fails send it back, why would htc give you this program? they allways say send it back and you'll get a new one?...
please post the tool, might give some insight after disasm. MFG area is interesting.
It's been written to special memory place.
Again, please post the tool you were given
how are you doing a hard reset?, are you using the clean memory tool software on your device, or are u pressing vol up and down simultaneously while powering on the device...... I just dont get how the program stays in memory after hard reset, even after flashing.
lucid said:
please post the tool, might give some insight after disasm. MFG area is interesting.
It's been written to special memory place.
Again, please post the tool you were given
Click to expand...
Click to collapse
yes, please post it.
if i "pdocread.exe -l" i find a 20MB-partition seperately.
could you post this part too?
okokur
Here is the tool! (BTW i fixed the problem)
okokur said:
yes, please post it.
if i "pdocread.exe -l" i find a 20MB-partition seperately.
could you post this part too?
okokur
Click to expand...
Click to collapse
I've attached the toll. I finally got rid of it by being able to rerun the program (which i prior tried a million times) and rewrite the parametres to "0" instead of 435 and 401. Give it a go if you know what you're doing and you can read log files.
regards,
G
You got rid of it. I edit out the post
Solution:
First backup your SD, after format with FAT32 .... reinstall your ROM and after insert your SD.
got dmmnit, glad u got rid of it, maybe we can learn how it.doez stick to the rom like that n use it in other apps like smartprotect. congrats!:
hi, do u mind sharing how u got rid of it?
I run this tool too, but after have no way to stop first try to read forum. Solution to stop program already is given from wmfreak. It is not need to make hard reset or to reformat SD card. Only things to do is to run program one more time and:
wmfreak said:
I finally got rid of it by being able to rerun the program (which i prior tried a million times) and rewrite the parametres to "0" instead of 435 and 401.
Click to expand...
Click to collapse
Thank you wmfreak