Hi! i had problems with my m3100 (right upper corner was sometimes automatically ´typing´ ) but this problem was resolved when i read guide how to fix it on this site (bussines card trick, or allow two screws), however it comes back and i must do hard reset, now after hard reset, when i turn my device on everything is ok (it shows welcome...) and i tap on display and align screen is necessary, i align the screen but it comes back always...so is there some chance to turn on system without screen aligment? or something that would fix it? of course i have warranty , but i don´t want to be month withou my phone thanks for answers
Hello to everybody!
this is a great job you are doing here!
there is a bit of a problem.
i had wm6 arte 100 with:
IPL:3.13.0001
SPL:3.13.0000
GSM:02.94.90
OS:3.13.00
and after running uspl :
SPL:1.11.0000 (I'm sure)
OS:3.13.0.0 (I think)
after a soft reset and a full restart all were running properly.
i took out sim card and sd card connected properly to pc and started the
o2 premium 2.0 full
the procedure went well i made some setup regarding appearence and tried a restart (not soft) for the sim and sd cards to mount.
the ppc boots i see the htc moving start-up screen and then stays in the usual green "windows mobile" screen.
is there any case it can be fixed or should i start trying to see if it can fly?
thank you very much at least for chance to see something different in my artemis screen!
keep walking
after trying several kind of restart here is what,
i pressed both selection keys and at the same time pressed the soft reset button and i kept pressing the selection keys untill a msg in black backround informed about a proccedure that would take place and erase all data etc,etc
i presssed the green key and after 10 sec i was working again full.
i proceded to further settings regarding touch flo and soft reset for the settings to apply, all well also!!!!!
i really do not how but i think i did it !!!!!!!!
Hi there,
I'm having an issue with my touch HD. I came to use my phone which was stored fine in my room not touched, I came to use it and it wasn't doing anything I pressed. So I decided to restart it and then when I tried to enter my lock code it wasn't noticing what I pressed and was pressing other numbers leading me to believe that it is a screen alignment issue.
However I managed to get on the screen align thing, but everytime I pressed the crosses, it would restart the sequence again and ask me to do it all again. I can't use the phone because I can't even get past the lock code.
Any suggestions? tried searching the forum but couldn't find anything..
Thanks in advance
Seanyy said:
However I managed to get on the screen align thing, but everytime I pressed the crosses, it would restart the sequence again and ask me to do it all again. I can't use the phone because I can't even get past the lock code.
Click to expand...
Click to collapse
Perhaps not of much use but I have had to "click on the crosses" in Align Screen up to 5 times after a ROM flash or similar so I would do it a healthy number of times.
If it is stuck in a long loop, I am stuck for suggestions.
That happens to me when I don't use the stylus for calibrating.
You have to be fast and press it firmly.
Thanks for the suggestions both of you, but still no luck
My Phone's screen suddenly not responding correctly to touch. I press at one place the phone respond erratically. I tried hard reset but I am stuck on Align Screen, it is not moving further even after repeated touch. PLease help.
Thanks
Amit
amit200465 said:
My Phone's screen suddenly not responding correctly to touch. I press at one place the phone respond erratically. I tried hard reset but I am stuck on Align Screen, it is not moving further even after repeated touch. PLease help.
Thanks
Amit
Click to expand...
Click to collapse
What happened? Did you flash a new rom to your phone? Did you drop it? Did it get any water damage? It sounds like something is wrong (mechanically / electronically)
I DID FLASH MY blackstone to 1.56 just change from german to french
the phone stucks on align
i cant align the screen , impossible to make a hard reset and all the RemoteCalibration doesnt support the blac100
the tric welcome.not doesnt work also
it works well in german now i cant flash it because invalid vendor id
radio 1.13.25.24
G52.62.25.34U
D.1.56.00.00
BLAC100 32 M
SPL-1.54.0000
ANY IDEA HOW TO FIX???
HOW TO EDIT THE REGISTRY VIA EXPLORE THE PHONE VIA ACTIVESYNCRO???
Hi manouba,
please try the following, if possible:
(1) Connect your Phone to your PC using Activesync (it works even when you are stuck at alignment screen).
(2) Download this Remote Screen Alignment program.
(3) Install and run this program from your PC.
(4) Choose SKIP to avoid the Align Screen Wizard. This program has a few features that you might want to use in the future.
(5) Restart the phone and you are done.
Let me know if this works or not.
Note: Incase your screen is badly aligned (if touch screen works); you can start the alignment wizard from settings and do few taps. You will not come out of the loop, so press any key like screen off button, Windows or restart the phone.
Best Regards.
Try using mobile registry editor: http://handheld.softpedia.com/get/Desktop-and-Shell/Windows/Mobile-Registry-Editor-10636.shtml
Hi all
first post and i got an interesting problem with my phone which i qualify as stupid. It all started when when my virtually keyborad started becoming unresponsive and when i tried to do a factory reset, i could not enter the 1234 number to start it. i left the phone for a while and then i could not get into the setting even . But i could receive calls but i could not call since i could not access any numbers on the dial pad( by pressing on the numbers of coruse but from dial log screen i could)
Anyway long story short while fiddling with the phone , i thought the lock feature was on that is why some of the touch functions was not totally responsive but to my sadness, i activated the lock and now the phone is stuck on the front page and i cannot access anything since i must press unlock at the far corner of the down screen but stupidly, while pressing on the unlock, since it is unresponsive, i cannot unlock the phone to get to the normal menu and so on.The only thing working is the square pad which tells me to press cancel then unlock to free the phone for normal use
By the way the lock feature is the one that blocks the phone so that you do not accidentally press on the touch screen and activate a program and not the lock thing operators put to limit your phone
I want to know if anyone can help me unlock the screen so that i can reset the phone or alternatively any other method via usb to reset my phone to factory settings. Any special buttons on the phone i can do to do that?
I tired leaving battery out for 24 hours but that did not work to unfreeze the touch buttons
Was thinking to reload the windows mobile completely via the micro card (which i read here) but i am not sure it will work or i fear it might brick my phone
Any suggestions will be welcome please.... thanks
Use myMobiler to control device from Pc through usb
Good luck
Ps: you'll probably have to change digitiser afterwards
Well tried the mobiler but the thing is that it asks the phone to allow the program to conenct and i cannot press yes on the touch screen since it is frozen or something so i am stuck again.
Very strange, it doesn't ask anything on my device...
Why don't you hard reset: press green and red buttons and while pressing, poke the stylus shortly in the reset hole then release the 2 buttons. It will ask something that you probably won't see, just press the action button and wait for it to restart.
Don't flash another on just yet - it may well cause issues as it sounds like your digitizer is broken. Don't hard reset either
Does it pick up anything at all? Have you tried tapping all over the place in that region to try and get a response, sometimes just under the screen also works. Do you use a screen protector? If not, try it with one, if yes, try it without, it may be interferring with it, or it may help the touch be picked up by the phone (Stupid, I know, but this is something I found to work before with my elfs, and omnias)
When it is locked, is activesync picking the phone up? You may be able to put the remote.exe into the windows folder (for myMobilier) and do it that way.
A digitizer costs about £6-£10. But due to the age of this device, as sad as it is, I would suggest trying a new phone out if funds allow for it.
ok so far i tried the hard reset (red button and green and pressed the on off button but nothing. When i press on off button alone it switches off but not hard reset. I did not know i had a reset hole at the bottom of the phone.I did that with red and green button but nothing. Only when i poke the hole alone it does a hard reset i think but when i switches back on it is still unresponsive and locked screen
I tried poking under screen protector nothing. Also i think screen is still responsive because when i tap on it, the screen lights brighter
I tired putting remote exe file on the phone( active sync is working and i can read files on the phone) but i have two remote files..which one to use ? the one that ends with 40 one or 50 .Also where to put it specifically..which folder.I tried my windows mobile based device but nothing.Also tried program files and data application nothing.
Mobiler cannot connect since from pc alone because it asks my phone permission
and i cannot tap yes to accept program.
so any more suggestions please
Hi
Maybe I wasn't clear enough, here's the exact procedure, it should work since you have to use only hardware buttons:
Hold down send/reject buttons (green/red at the front) and reset with the stylus; release the stylus but keep holding the buttons till you get 'this will erase all your personal data' message, then press 'action' (big front button) to hard reset.
If Hard reset doesn't work then your device hardware is faulty.
If he hard resets he will liekly not be able to align the screen on initial setup tito12.
Avanisha. If you try to run one of the remote.exe it will say this is not a valid windows application, thats the one that needs to go into windows on your phone.
captainstu72 said:
If he hard resets he will liekly not be able to align the screen on initial setup tito12.
Click to expand...
Click to collapse
Hi captainstu72, i was under the impression that he messed up something in his system so a hard reset would hopefully solve the problem. In case he still can't align the screen after HR then he has to replace the digitiser. Mymobiler will not solve anything, pls read the 1st post: he wanted to do a factory reset. He just have to sync before HR.
thks tito 12..problem was solved with your help.J ust did not get the steps of hard reset right. Phone is working ok now and screen is ok as well as tap function. thank god i don't need a digitizer. thanks to captainstu72 for the help as well .You were right tito..seems i ran a program and then all hell broke on my phone. I wanted to factory reset but as you know the pad was locked.
Glad I could help, enjoy your device
Ahh okay, guess i mis read something! Sorry
Glad its all sorted though, I was just concerned he may end up in an annoying align screen loop