Using Cyanogen RC2 (good work Jacob)
Using a fairly cheap bluetooth stereo headset to listen to music via bluetooth and whichever music app is bundled with Cyanogen (AOSP?)
http://www.mobilefun.co.uk/clip-and-talk-bluetooth-clip-stereo-headset-p23542.htm
Whenever i have no signal (very often in my office) there is a consistent beeping every 5 seconds in my headphones to notify me. Has anyone experienced this?
Is it a phone feature? Bluetooth headset feature? Can i turn it off? I don't want to go into airport mode or turn mobile network off because my signal comes and goes and i need it on in case my preggo wife calls.
Is there anyway anyone knows to stop beeping notifications when you lose signal and you are connected to a bluetooth headset. Thanks guys. Expecting 0 replies cos i doubt it is a common problem but thanks in advance anyway lol.
Related
Hi Guys, don't know if it's just my Atom but whenever i activate either Bluetooth or Wifi, there is no incoming ring when I receive a call.Is this normal? Shall appreciate your input.
Cheers,
I'm not sure if the problem is related but I occasionally lose sound when trying to make calls and the Bluetooth is on. The phone works fine when receiving calls. To fix it I will have to turn BT off. I wonder if the phone is picking up other BT devices around it and try to channel the sound to that device even when it's not suppose to??
Wondering if anyone has had this problem. I haven't pinned a time down yet. I use a motorola car kit. It will disconnect and end the call for no reason. Is there a timer to auto disconnect in the bluetooth stack? Any help is appreciated.
approx 4minutes or less
I was having a problem w/mda and bluetooth and sometimes without bluetooth, in that the entire network would just drop when the call gets close to 4 minutes.... I called tmo about it and they simply gave up and said maybe its the phone...so they sent me a replacement mda, used it today during one call and couldn't believe that the call lasted longer than an hour...
Mine is only with bluetooth. I guess a little more info is needed. If I hit the voice dial button on my car kit I get the voice command tone. I have also used bluetooth to play music over the car kit with the voice command controls(just for fun, horrible quality). It will disconnect while it's playing music no call involved. I have a feeling it's the bluetooth connection timing out but I'm not sure. It's frustrating.
so its not happening during phone calls???
see there might be a bluetooth timeout that tmo doesn't know about...I have to use bluetooth and it seems like every 4min or less it blanks out everything and sometimes I even have to re pair the two devices.... I would try making calls and using the bluetooth w/o car kit...mine did some of the samethings like streaming music thru bt headseat and it would blankout with that also even when not on a call..
Car Kit Not Staying Paired???
I guess I wasn't clear. It happens in both situations. I think i have to re-pair after as well. As far as I know it doesn't stay paired. When a call comes in I usually have to wait about 2 rings before it rings through the car kit. Also when I make a call by hitting the voice dial button on the car kit the blue light blinks for about 2 seconds then I get the voice command sound. I assume that the blinking is it re-pairing. I guess I need info on how to keep it paired.
Anyone? I have found that time dosen't seem to be a issue as it has done it a 1min 43 seconds and 2 mins 38 seconds.
GreggSymington said:
Wondering if anyone has had this problem. I haven't pinned a time down yet. I use a motorola car kit. It will disconnect and end the call for no reason. Is there a timer to auto disconnect in the bluetooth stack? Any help is appreciated.
Click to expand...
Click to collapse
Try turning on the bluetooth first while your phone is off. Once the bluetooth is on, then turn on your cell phone. I tried many times in frustration why it is saying "phone is disconnected" looking for problems. Then it works now and even the phone book in my Nokia and Garmin GPS. Hope it helps you too.
Turn on bluetooth device first while the cell phone is off. Once bluetooth is on, then turn on the latter. Hope it works. Do it everytime you use bluetooth device in your car.
Is there a way for audio to be muted when the connection between my hermes and the headset is lost. It is really annoying when I walk out of range of my cell at work or the battery runs out on my headset to have the music blaring out of my cell phone. Does anyone know if this is possible?
Whenever i use the MW600 to anwer calls , ppl complain that when they say something they can hear themselves echoing what they said. Anyone with this headset has the same issue or know how to fix it?
Turn the volume down on it then.. Pretty simple fix.
thanx for the suggestion, but turning down volume when using it in car doesn't work, it seems that when you use headset the phones mic doesn't turn off so it picks up the car speakers and that's why people hear themselves echoing
The MW600 isn't made for Car Use... So the issue can be normal!
I've noticed that my MW600 doesn't always sync to Phone and Media audio, sometimes just to Media - which will probably mean that the Mic on the phone is still open, hence the problem you describe.
I've worked out that the way to avoid this is to connect to the phone the following way:
1) Enable Bluetooth on phone
2) Turn on MW600
3) Check in BT setting that both Phone and Media audio are connected and that the headphone symbol is displayed.
I find that if I turn on the MW then activate BT on the phone, they just don't connect properly...
I use mine in the car on a regular basis and find it superb, and have had no complaints
thanx for this tip I'm going to try it, I hope it fixes the echoing
I have searched and searched and I am actually currently waiting two new Jabra Extreme2 headsets from Jabra.... but I don't have a lot of faith that the problem will be solved.
The scenario is simple.. Calling and listening to music is fine. The issue is on incoming calls, and only MOST of the time.
If the headset is on and connected (bluetooth) the ringtone will start to stutter and the announcement in the headset will be "call from " and a number instead of the actual name in the contact list. At this point the phone will be frozen. The call will roll to voicemail. The only way to shut the headphone up from repeating the number continuously is to turn it off. Once the headset is off, you can usually get to the pulldown and turn off bluetooth. It will take awhile (minute or two) to release, but it will. At this point you can turn on the headset and turn on bluetooth again and make a call without issue. Maybe even receive a call... but about 8 out of 10 calls will result in the above.
My wife and I each have an Epic 4g and a Jabra Extreme2 headset. The issue is the same on both phones. We have older Jabra BT530 headsets that other than sounding like crap. (old bluetooth tech) work great, no issues.
I'm not convinced the issue is the headset. I mean really, there is no "software" for the headset. It's just a bluetooth connection, so why is the phone freezing? I tried different ringtones as I thought that might be the issue, but it isn't.
Does anyone have any thoughts or insight, or any idea if it could actually be the headset causing the phone to freeze.
Also, does anyone know how to disable the PBAB as that seems to be related but without being able to disable it, I can't confirm.
Any help or insight would be greatly appreciated. Anyone using the Extreme2 ?
Well, I have a Moto Finiti Bluetooth and I am not having any of the issues you mentioned so far. Thankfully its connecting better than earlier ROM releases on my Epic
Sent from my SPH-D710 using xda premium