Hello fellow HD2 users,
I've got an HD2 T-Mobile UK. I've just tried my luck with HSPL, I've succeessfully installed HSPL using the steps in this thread: http://forum.xda-developers.com/showthread.php?t=609477
However, when I copied the LEOIMG.nbh (1.48 offiicial rom) file to the micro SD 8GB card; and rebooted, things seemed ok untill it suddenly stopped the progress of flashing the ROM and gave me a Grey screen with the Error 00028002 "not Allow" sort of thing.
So I tried yanking battery out, rebooting normally, it displays a grey triangle with " ! " in the middle and then displays the 00028002 error then back to Tri colour bootloader, I noticed that the HSPL is gone and its back now to 1.42.0000
I even tried a Factory reset, it does the reset I reboot, but it still shows me grey triangle and same routine. I've tried everything now. This bloody T-mobile phone is just useless to me at the moment !
Can you please HELP !!! Thank you so much !
Regards !!
Ok found solution, I just had to install the official T-mobile 1.43.110.0 ROM from this link:
http://rapidshare.com/users/258XUJ
After just switching on the phone with microsd inside, I just plugged the usb and started the RUU and followed the steps and things are back to square one now.
not thrilled that it has been a nightmare so far to get a new rom on.
but at least I can use my phone with its basic functionalities. not gona push my luck again...
You cannot flash official ROMS from the sd because it replaces the SPL with a stock one. Presume it got half way through then decided the ROM was not for your device since it hasd replaced the SPL. Cooked ROMS are ok to flash from SD but for Stock use the RUU.
tell me it's working please.my HD2 from UK T-Mob is same "bricked" and in Slovakia is very very difficult to find somebody who can fix this....i think maybe only the HTC repair center
^
If your phone can load up into the boot loader (tri-color screen) your phone is not bricked.
Deeper Trouble:Same error,but cannot use USB!!!
Guys,
im in even much deeper **** now.I accidentally tried flashing a stock ROM via SD card and now ive gt the same ROM code error.What makes this worse is that my Vista computer is not recognizing any USB connection when i connect my HD2 to the computer.If i need to flash a stock rom via RUU wrapper to get through this stupid ROM code error, i need a USB connection at the first place...which IS NOT WORKING NOW!!!...im sitting duck here guys...i really really need your help on this one.im extremely frustrated and helpless.thanks alot...
When u say USB not working, how do you know?
Put phone in bootloader, connect USB cable,,, on phone does "serial" become "USB"? If yes then just run the flash.
samsamuel said:
When u say USB not working, how do you know?
Put phone in bootloader, connect USB cable,,, on phone does "serial" become "USB"? If yes then just run the flash.
Click to expand...
Click to collapse
Go to this thread Sam as kawshigan started a new thread
semo2010 said:
Ok found solution, I just had to install the official T-mobile 1.43.110.0 ROM from this link:
http://rapidshare.com/users/258XUJ
After just switching on the phone with microsd inside, I just plugged the usb and started the RUU and followed the steps and things are back to square one now.
not thrilled that it has been a nightmare so far to get a new rom on.
but at least I can use my phone with its basic functionalities. not gona push my luck again...
Click to expand...
Click to collapse
broken link
I decided it's best to open another topic, as the subject has changed and the other topic seems to have died more or less.
I have found out that the problem with my HD2 is that the radio is corrupted. However, I failed every time I tried flashing a new radio, even though I tried both USB and SD card methods.
Is there any way I can format the part of the memory where the radio is? I would also like to mention the fact that task29 failed too, as it never goes over 0%.
For anyone who doesn't know what my problem is: the device will not go further than a white screen of death when booting. I can get into the bootloader, but that seems to be useless up to now.
I would like to point out the fact that I successfully flashed a custom ROM via SD card, but that made no difference whatsoever.
boot to bootloader, what does it say next to 'spl'?
assuming the answer to the first part is something like ''x.xx.hspl'' then try flashing a new radio. Go for, example, 2,10 radio, that way it doesnt matter what rom is on there, it should work.
If teh answer to teh first part is ''x.xx.0000'' then hspl is not installed, and you should start over with hspl2 or hspl3
samsamuel said:
boot to bootloader, what does it say next to 'spl'?
assuming the answer to the first part is something like ''x.xx.hspl'' then try flashing a new radio. Go for, example, 2,10 radio, that way it doesnt matter what rom is on there, it should work.
If teh answer to teh first part is ''x.xx.0000'' then hspl is not installed, and you should start over with hspl2 or hspl3
Click to expand...
Click to collapse
I have tried several radios, such a 2.07, 2.10, 2.12 and neither of them worked.
I currently have 1.42.HSPL installed, so it should.
USB does nothing: one time it got to 1% then failed because of "the image being corrupt", and the other 100 times I tried it never went past 0%.
SD card is no better: the progress bar fills up then it says:
00018003
LEOIMG.nbh - FAIL
RADIO_V2 - FAIL
Update terminate - UPDATE FAILED
And that's it.
i should stop using sd card, for a start. Stick to one method (usb) and the possible problems immediately halve.
First off i would return to a stock rom. In my case i would use teh original o2 1.43 stock rom, but you can use the 1.66 wwe if you arent sure of your stock.
boot into bootloader and physically check that hspl is still installed - it can be removed by sd card flashing, even if teh rest of teh flash fails, so always worth double checking, not just assuming that it is still installed.
assuming it says 1.42.hspl as you expect, and not anything ending .0000, then connect to usb and wait for teh word 'serial' to become 'usb'
When it does, on your pc run the stockrom.exe file.
Please post any resulting success/errors..
(oh and dont make the newb mistake of leaving a rom image on your sd card, else it will try and flash that.
Step 1: Downloading WWE 1.66.405.2 from another thread I found here on XDA.
Step 2: Formatted SD card and put it back into the device as it was, empty.
Step 3: Physically checked that my bootloader says 1.42.HSPL and it does.
*** Waiting for download to finish ***
Step 4: Loaded the phone into bootloader and connected the cable, so that it says "USB" instead of "Serial".
Step 5: Run as administrator the _HTC HD2_RUU_Leo_HTC_WWE_1.66.405.2_Radio_Signed_15.30.50.07U_2.06.51.07_Ship I downloaded earlier.
Step 6: Went through all the steps indicated by the installer and it began.
It's 17:35 here and progress is 0%. I will be waiting 10 more minutes, then edit this post.
EDIT: It's 17:42 and the Update Utility says:
ERROR [262]: UPDATE ERROR
The ROM Update Utility has encountered communication errors during the update process. The program will guide you step-by-step to recover from the errors so you can continue with the update.
Step 7: I click on "Recover", then follow the four simple steps to recover my device.
Step 8: The Update Utility goes back to the "Update" button screen, and the whole process repeats over and over.
Any other advice?
SECOND EDIT: I forgot to mention that before clicking the "Update" button, I noticed that there was a blank space where the current image name should have been. Maybe this has something to do with all that is happening?
anrabi4 said:
Step 1: Downloading WWE 1.66.405.2 from another thread I found here on XDA.
Step 2: Formatted SD card and put it back into the device as it was, empty.
Step 3: Physically checked that my bootloader says 1.42.HSPL and it does.
*** Waiting for download to finish ***
Step 4: Loaded the phone into bootloader and connected the cable, so that it says "USB" instead of "Serial".
Step 5: Run as administrator the _HTC HD2_RUU_Leo_HTC_WWE_1.66.405.2_Radio_Signed_15.30.50.07U_2.06.51.07_Ship I downloaded earlier.
Step 6: Went through all the steps indicated by the installer and it began.
It's 17:35 here and progress is 0%. I will be waiting 10 more minutes, then edit this post.
EDIT: It's 17:42 and the Update Utility says:
ERROR [262]: UPDATE ERROR
The ROM Update Utility has encountered communication errors during the update process. The program will guide you step-by-step to recover from the errors so you can continue with the update.
Step 7: I click on "Recover", then follow the four simple steps to recover my device.
Step 8: The Update Utility goes back to the "Update" button screen, and the whole process repeats over and over.
Any other advice?
SECOND EDIT: I forgot to mention that before clicking the "Update" button, I noticed that there was a blank space where the current image name should have been. Maybe this has something to do with all that is happening?
Click to expand...
Click to collapse
im in the same boat mate and have yet to get it working..mine doesnt fail flashing all the time, but quite often. same thing with the radio v2 fail. i can use bootlader no problem, use hspl to lock and unlock no problem, sometimes a flash goes ok with usb but quite often it doesnt, and when flash from sd to say put a stock rom and relock it it will quite often fail exactly like yours but other times it says its a good flash. if its a good flash itll hard reset like normal, but just wont boot past the white htc screen. i agree at this point, it has to be something related to the radio...whether its corrupt like you were saying or some kind of hardware failure
just a note it is odd that a number of us are all having the same issue..its not just a few anymore
heh ignore, ill re read
samsamuel said:
step 2....... why? did i not advise against sd card flashing? when you run the update on your pc it is restarting the phone, which is immediately flashing the rom from your sdcard,,,,, not the one on your pc.
the problem is that it immediately has removed hspl, and so the rom fails the region check.
remove the nbh from your sd card, and do all the other steps. you may have to reapply hspl, so run hspl2 and choose either 1.42.hspl or 1.66.hspl
Click to expand...
Click to collapse
i just read his step 2 and it sounds like he is saying he formatted it and inserted it empty
the-wrangler said:
i just read his step 2 and it sounds like he is saying he formatted it and inserted it empty
Click to expand...
Click to collapse
heh, d;oh. ill re read and try again (it was the LEOIMG.nbh - FAIL RADIO_V2 - FAIL bits from teh earlier posts that had me thinking he was still using sd card, cos those are sd card flashing errors)
so with the communications erros, could be AV software, firewall, or simply wrong usb port. try all ports (im sure you have by now) and if poss try a whole different pc.
samsamuel said:
heh, d;oh. ill re read and try again
Click to expand...
Click to collapse
lol no worries, i sure appreciate any help fellows like him and i can get. im certainly not new to winmo and im totally stumped.
Also guys, if you are having trouble flashing from USB , try some basic troubleshooting, if you are sure everything on the phone is correct ...
Try different USB port, also USB hubs and flashing can be bad mojo ...
Try a set of usb ports on the back of the PC rather than the front.
Try a different PC
Try a different cable
I also know it sounds strange, but I have seen some anti virus cause a flash to fail because of active scanning and it tries scanning the files in the flash directory while the flash is going on and locks them ...
All I got .....
oh and if the rom you downloaded came as a zip, dont run it from within teh zip. extract it first.
watcher64 said:
Also guys, if you are having trouble flashing from USB , try some basic troubleshooting, if you are sure everything on the phone is correct ...
Try different USB port, also USB hubs and flashing can be bad mojo ...
Try a set of usb ports on the back of the PC rather than the front.
Try a different PC
Try a different cable
I also know it sounds strange, but I have seen some anti virus cause a flash to fail because of active scanning and it tries scanning the files in the flash directory while the flash is going on and locks them ...
All I got .....
Click to expand...
Click to collapse
thanks mate, cant speak for the op but ive tried 3 different computers (xp,vista,7) different cables, everything. seems like roms will flash but it doesnt recognize a radio when booting, hence the white screen with no rgd info..so stumped.
edit..tried many many stock and custom roms and just about every radio out
The thing is that you seem to need a non-corrupted ROM to flash a radio, and need a non-corrupted radio to flash a ROM. As we have neither of them, all I can say is good luck to the guys fixing it at the service center.
I have given up; I have LITERALLY tried every possible solution I could think of. Just for the sake of it, I'll make a list here:
1. Tried all USB ports available.
2. Tried installing different drivers for the Active Sync.
3. Tried task29 w/o MTTY.
4. Tried task29 with MTTY. (Successful, but useless)
5. Tried removing HSPL.
6. Tried changing HSPL.
7. Tried flashing custom ROM. (both USB and SD)
8. Tried flashing stock ROM. (both USB and SD)
9. Tried flashing radio. (both USB and SD)
10. Double (even triple) read all of your useful comments and posts, clicked and typed the hell out of my mouse and keyboard, googled for any possible term I could come up with which was related to our problem.
I have given up for today. Tomorrow morning, I`ll have access to another laptop and I`ll try performing the same operations there, hopefully there will be a difference. All I want now is to get rid of HSPL off that bootloading screen, so that the guys from HTC won't have any reason to decline my warranty.
If nothing works, I will microwave the device for 3-5 seconds, and hopefully it`ll stop booting.
If you guys have any other suggestions, do not hesitate.
anrabi4 said:
The thing is that you seem to need a non-corrupted ROM to flash a radio, and need a non-corrupted radio to flash a ROM. As we have neither of them, all I can say is good luck to the guys fixing it at the service center.
I have given up; I have LITERALLY tried every possible solution I could think of. Just for the sake of it, I'll make a list here:
1. Tried all USB ports available.
2. Tried installing different drivers for the Active Sync.
3. Tried task29 w/o MTTY.
4. Tried task29 with MTTY. (Successful, but useless)
5. Tried removing HSPL.
6. Tried changing HSPL.
7. Tried flashing custom ROM. (both USB and SD)
8. Tried flashing stock ROM. (both USB and SD)
9. Tried flashing radio. (both USB and SD)
10. Double (even triple) read all of your useful comments and posts, clicked and typed the hell out of my mouse and keyboard, googled for any possible term I could come up with which was related to our problem.
I have given up for today. Tomorrow morning, I`ll have access to another laptop and I`ll try performing the same operations there, hopefully there will be a difference. All I want now is to get rid of HSPL off that bootloading screen, so that the guys from HTC won't have any reason to decline my warranty.
If nothing works, I will microwave the device for 3-5 seconds, and hopefully it`ll stop booting.
If you guys have any other suggestions, do not hesitate.
Click to expand...
Click to collapse
lol i hear ya, my issue is i cant seem to locate my receipt of sale for the bloody warrenty...
the-wrangler said:
lol i hear ya, my issue is i cant seem to locate my receipt of sale for the bloody warrenty...
Click to expand...
Click to collapse
you should be able to contact the seller for proof, especially if it was a carrier or someone like p4u.
samsamuel said:
you should be able to contact the seller for proof, especially if it was a carrier or someone like p4u.
Click to expand...
Click to collapse
ya i have, im waiting with fingers crossed lol. stuck with a brutal android cliq until i can get my hd2 back running. really appreciate winmo and hd2 after having to use this
after all, the-wrangler, what are u going to do? you can't just send it in for repairs if you have got HSPL installed...
microwave as well?
anrabi4 said:
after all, the-wrangler, what are u going to do? you can't just send it in for repairs if you have got HSPL installed...
microwave as well?
Click to expand...
Click to collapse
no, bootloader works just fine and it flashes sometimes..flash stock from sd and hspl is back on with stock rom..just wont boot.
oh... lucky you, I suppose...
I sure wished I could get it back as well, really don`t want to use such drastic measures...
My friend asked me to try recovering his T-mobile DE Hero, it was bricked while my friend was trying to root it
I tried to flash official rom, but RUU gets error 170...
This what appears on screen when device is on:
error 170... thats the usb connection error right?
this could be because the drivers are not installed properly.
read this thread, then try again
http://forum.xda-developers.com/showthread.php?t=647353
Although error 170 is indeed USB error, (with windows 7 normally) the nasty looking Icon at the bottom of the screen does not look good, never seen that before
Let us know how you get on please
I had the same error with mine.
I ended up in installing a custom ROM, since NOTHING would work. No drivers no nothing. It just refused to read the phone.
I installed VillainROM 12, it has OS 2.1 so it's working perfectly
I had the same problem, but I was trying to flash my German G2 using an HTC Official RUU. I've been able to flash the recovery rom using fastboot and then boot it, but that's where my progress has ended. I'm about to flash VillainROM12.0.0-Full and see what happens. I'll let you know.
EDIT: VillainROM12 installed via AmonRa Recovery menu, but rebooting takes me right back to the RUU screen with an Xed-out EPROM
Nothing helped
I tried everything You said, but device is showing same screen, I also tried using SD card method but when I turn Hero on (while holding Vol-) same screen appears
Does anyone have any other idea what to do?
Its looking like a problem with a radio (drivers etc). Try to update it through recovery if u can enter there.
You can see in my first post the only screen where I can enter...
Well.. This icon with a "chip" probably say a SPL or Radio of phone is just f***ed up.. :/ You can enter to fastboot so drivers of graphics and other modules are in good condition..
wheeeler i think u should find a .zip with a official SPL and radio and update it through recovery like u did it with Villain ROM
I got some idea but I think u tried it before.
iwanrakic U can connect to phone via SDK?
Try this command. It should update it.
C:\sdk\tools>fastboot flash radio radio.img
Of course u need image of official radio.
What driver does Windows report installed when you plug it into your PC in that mode?
Hello Guys.
My nephew has an HTC HD2 (I supose that). It is stucked on the HTC screen. I tried a lot of thing, but nothing works, i'm affraid to make it worst. If someone can help me.
Some informations.
I don't know if it was working with android or windows;
I can access the tri color screen holding volume down and the power button or the reset button on the back of the device;
I already made a hard reset (holding vol up and down and reset buttons) the process was ok but nothing changes.
I don't know what kind of HD2 is it. On the back of phone I have this: HTC HD2 T8585, on the next line some asian characters, next line CCAF093G0600T0.
I tried to put images but i can't, i'm new, so, only link adresses.
This is the image of my tri color screen
i.imgur.com/HtbtBCu.jpg?1
If I try Task29 from Toolkit I receive this error
i.imgur.com/569SjSn.png
I tried all HSPL (HSPL 2, HSPL 3 and HSPL 4) all kind of errors, but the persistent error on HSPL4 is Flow: 00006, Error: 00006, Unknow
If need some other information.. just ask.
Thanks in advanced.
If it has coloured call/end keys (red&green) then it a US T-mobile model
If all keys are white then it the standard model.
Your hd2 has been unlocked by xtc clip box or similar so cid is probably bypassed without need for HSPL .
I would remove sim card & memory card & try flashing a standard windows rom via usb & if fails try using the sd card flash method.
Worth checking windows drivers are installed or just reinstall WMDC (link in hd2 wiki), using sd method removes pc issues from the problem.
If standard windows rom fails try a custom windows rom such as energy as they contain no radio or spl so sometimes will flash fully when hardware nand issues cause full rom to fail .
working rom links & help can be found in hd2 wiki >
http://forum.xda-developers.com/wiki/HTC_HD2
Ohhh.. Very good informations.
My call/end keys are coloured, so, I have an US T-Mobile model, is right?
I forgot to tell, i live in Brazil.
Now, i'm using windows 10, is it possible to use with WMDC? I tried to find a compatible version but no success.
There is a possibility to manage this phone with windows 10?
Thanks.
First thing I would try is flashing the original US t-mobile hd2 rom via sd card method as removes your pc & w10 from equation ...
us t-mobile rom >
http://www.androidruu.com/Leo/RUU_L...adio_15.42.50.11U_2.15.50.14_LEO_1.5_Ship.exe
you will find guides on flashing from sd card if search or perhaps link in wiki !
---------- Post added at 04:53 PM ---------- Previous post was at 04:40 PM ----------
You should have most functionality of wmdc in windows 10, installing wmdc6.1 in compatibility mode of vista sp2 may help, also connecting device prior to wmdc install may load better driver resources perhaps !
Hello again..
I tried to install this ROM by SD card Method, but the screen shows a white background with the message Loading... and nothing more.
I tried by computer and after 1% I received an error informing that the image file is corrupted. Then, i tried another download site but the error was the same.
Any idea?
Thanks
Just to add more information.. I tried one more TMOUS ROM: RUU_Leo_1_5_TMOUS_2.13.531.1_Radio_15.39.50.07U_2.10.50.26_Signed_LEO_Ship same result, white screen with the word Loading... and nothing more.
I tried also two more ROM's:
RUU_Leo_HTC_WWE_1.43.405.1_Radio_Signed_15.26.50.07U_2.04.50_22_2_Ship and
RUU_Leo_S_HTC_WWE_3.14.405.2_Radio_15.42.50.11U_2.15.50.14_LEO_S_Ship
Both with the same result. After press the power button to start the updating it begins the updating and failed on the first step.
Any idea?
Thanks.
flash from sd card >
http://forum.xda-developers.com/showthread.php?t=681317
if TMOUS rom does not flash try energy custom rom (such as one in my signature) and see if that does.
All these tries was made by Sd Card...
And with your Energy ROM.. the same thing. only white screen with a blue word "Loading..." and nothing more happen.
another tries?
Thanks
Besides trying another smaller sd card such as 2gb or 4gb & making sure nbh file in root of card & trying vis usb flash on a couple of computers you running short on options.
You could also try flashing just radio rom image & see what happens !
Please kindly help
Hello everyone.
I brick my htc hd2 leo english version in an attemp to change it to android but for some reasons it did not work on my device, I want to go back to the stock rom but i have search google including this forum for the stock rom but all i get is a dead links..
Please if anyone knows a working link to download the rom, should kindly post it here.
Thanks in advance.
working links >
http://forum.xda-developers.com/wiki/HTC_HD2#Official_ROMs_.26_Radios