Serious HD2 00028002 error CAN"T USE PHONE! - HD2 General

Hello fellow HD2 users,
I've got an HD2 T-Mobile UK. I've just tried my luck with HSPL, I've succeessfully installed HSPL using the steps in this thread: http://forum.xda-developers.com/showthread.php?t=609477
However, when I copied the LEOIMG.nbh (1.48 offiicial rom) file to the micro SD 8GB card; and rebooted, things seemed ok untill it suddenly stopped the progress of flashing the ROM and gave me a Grey screen with the Error 00028002 "not Allow" sort of thing.
So I tried yanking battery out, rebooting normally, it displays a grey triangle with " ! " in the middle and then displays the 00028002 error then back to Tri colour bootloader, I noticed that the HSPL is gone and its back now to 1.42.0000
I even tried a Factory reset, it does the reset I reboot, but it still shows me grey triangle and same routine. I've tried everything now. This bloody T-mobile phone is just useless to me at the moment !
Can you please HELP !!! Thank you so much !
Regards !!

Ok found solution, I just had to install the official T-mobile 1.43.110.0 ROM from this link:
http://rapidshare.com/users/258XUJ
After just switching on the phone with microsd inside, I just plugged the usb and started the RUU and followed the steps and things are back to square one now.
not thrilled that it has been a nightmare so far to get a new rom on.
but at least I can use my phone with its basic functionalities. not gona push my luck again...

You cannot flash official ROMS from the sd because it replaces the SPL with a stock one. Presume it got half way through then decided the ROM was not for your device since it hasd replaced the SPL. Cooked ROMS are ok to flash from SD but for Stock use the RUU.

tell me it's working please.my HD2 from UK T-Mob is same "bricked" and in Slovakia is very very difficult to find somebody who can fix this....i think maybe only the HTC repair center

^
If your phone can load up into the boot loader (tri-color screen) your phone is not bricked.

Deeper Trouble:Same error,but cannot use USB!!!
Guys,
im in even much deeper **** now.I accidentally tried flashing a stock ROM via SD card and now ive gt the same ROM code error.What makes this worse is that my Vista computer is not recognizing any USB connection when i connect my HD2 to the computer.If i need to flash a stock rom via RUU wrapper to get through this stupid ROM code error, i need a USB connection at the first place...which IS NOT WORKING NOW!!!...im sitting duck here guys...i really really need your help on this one.im extremely frustrated and helpless.thanks alot...

When u say USB not working, how do you know?
Put phone in bootloader, connect USB cable,,, on phone does "serial" become "USB"? If yes then just run the flash.

samsamuel said:
When u say USB not working, how do you know?
Put phone in bootloader, connect USB cable,,, on phone does "serial" become "USB"? If yes then just run the flash.
Click to expand...
Click to collapse
Go to this thread Sam as kawshigan started a new thread

semo2010 said:
Ok found solution, I just had to install the official T-mobile 1.43.110.0 ROM from this link:
http://rapidshare.com/users/258XUJ
After just switching on the phone with microsd inside, I just plugged the usb and started the RUU and followed the steps and things are back to square one now.
not thrilled that it has been a nightmare so far to get a new rom on.
but at least I can use my phone with its basic functionalities. not gona push my luck again...
Click to expand...
Click to collapse
broken link

Related

(UN)Hard SPL and generic rom. What do you think i should do?

Hey folkes
I dropped my phone yesterday. First the display would'nt show anything but this morning tha display worked fine but the touch does'nt work so i need to send it to the servicepartner that my provider uses.
Should i (un) hard spl and install a generic rom? Is there anything else i should do so they cant se that i used non generic roms?
/A from now on a Nokia N95 user again :-(
Yes, definitely.
Flash a generic ROM back on first, then flash the original SPL back.
I just hope you can do it without the touch facility working.
ZenithUK said:
Yes, definitely.
Flash a generic ROM back on first, then flash the original SPL back.
I just hope you can do it without the touch facility working.
Click to expand...
Click to collapse
You can do this from a computer with the RUU so there isn't a problem I guess.
Good luck dude!
If I were you, I try first to make a hard reset in order to see if touch is really dead or not...
Can i put back the stock SPL with the micro SD card? The problen now is that i cant run the RUU becurse i can't configure my device. I am pretty much stuck at "Tap the screen to configure your device" I knew before that i could get stuck here but i was able to flash the stock rom anyway after the hardreset.
But when i try to put the stock SPL back the RUU says "Connection error"
So my onlu option at this point is if this works with the micro SD method.
Any experience anyone?
Badankan78 said:
Can i put back the stock SPL with the micro SD card? The problen now is that i cant run the RUU becurse i can't configure my device. I am pretty much stuck at "Tap the screen to configure your device" I knew before that i could get stuck here but i was able to flash the stock rom anyway after the hardreset.
But when i try to put the stock SPL back the RUU says "Connection error"
So my onlu option at this point is if this works with the micro SD method.
Any experience anyone?
Click to expand...
Click to collapse
You can still run RUU, but make sure you flash the stock rom first.
To get RUU to work, start your x1 in boot loader mode (turn it off, then press and hold both power and volume down until the tri colour screen comes up), now connect your phone to your pc with the usb cable and run the RUU.

i think my phone is dieing

Hello all,
I'm not sure but i think my blackstone is on its last legs.
It all started after i flashed to Dutty's last rom the r15 one. Did the usual uspl and eveything went to plan. Then about a week ago the phone frooze, i could'nt get it to reset so had to take the battery out (no biggy). Then tried turning it back on, and it just frooze again right at the windows start-up screen. So did a hard reset and the phone seemed very slow and jumpy.
Then i thought maybe the download of dutty's rom wasn't the best. So today i had planned to install a different rom and see if it was just a bad download or sumthing. And heres the big problem, i can't get the bootloader to connect to my pc.
And what seems strange is that when i enter the bootloader it flashes up with the re/green/blue/white screen andt ehn it shows a grey screen with "loading......." for about 10 seconds then comes back the normal bootloading screen. As usual serial pops up at the bottom, but when connected to my pc it won't show USB!!
I have win7 64, but i have set it up so i can flash using USPL as thats how i got dutty's R15 rom on there.
Any help would be great and hopfully i can get this sorted swn as i love my hd.
p.s
i've spent the past 2 hours searching here and havent found anyone with the same problem.
Thanks
Antony
if you could update from the sd card that would solve some of your problems.but i realy do not know if it is working if you do not have HSPL.
maybe you can find some info on the forums about updating via sd card without HSPL.
or you could try to connect to a computer with other operating system than windows 7.
i am now installing the stock rom.
hopefully then i wil be able to install a cooked rom again.
berbecverde said:
if you could update from the sd card that would solve some of your problems.but i realy do not know if it is working if you do not have HSPL.
maybe you can find some info on the forums about updating via sd card without HSPL.
or you could try to connect to a computer with other operating system than windows 7.
Click to expand...
Click to collapse
Thanks for the help,
I will see what the outcome is from the stock rom. And if i can't get it working again with win7 then i'll have to set up my mini pc (made a pc inside an old nintendo SNES) as thats got xp running
thanks once again
just for my curiosity what method are you using to flash a stock rom if you cannot connect to computer through usb?
berbecverde said:
just for my curiosity what method are you using to flash a stock rom if you cannot connect to computer through usb?
Click to expand...
Click to collapse
Well after more hours spent reading thro web page after web page, i stumbled over someone saying that it could be down to the usb cable and i have a few mini usb one, so tried them all, finally got the bootloader to show the usb.
I was then going to install a cooked rom, but thought i'd be the best to go for stock first.
All is working ok now. I'm not sure if it was down to the usb cable totally tho as it was a bit strange the whole grey loading screen on the bootloader which has gone now with the stock rom.
ah well looks like its fixed for now.

[Q] Help!

Hey guys,
Sorry to be a burden but I'm having a few issues with my hd2, and being a noob I didn't really know where to turn except this forum.
Basically my dad bought the hd2 from the UAE early this year and it all worked fine on stock settings for about 6 months. In the last few months, however, the phone started to lock up, and it got to the point where it wouldn't even boot properly.
In an effort to fix the problem I went with a hard factory restore, however, this seems to have caused more problems as now the phone is stuck in the bootloader.
I've been searching for hours, and have come to the conclusion that I need to update the flash? and then possibly install a new rom on the phone?
My major issue in doing this though, is that I can't seem to connect to activesync while the phone is in the bootloader.
Please help me sort this out.
First of all lets make sure that your trying perform the hard reset correctly.......
You need to hold down both volume buttons whilst the phone is turned off..... Then tap the power button and keep the buttons held down.......
Release them when you see the confirmation screen.........
Powering on while holding only the vol down button will take you to bootloader....
If you need to reflash the device then have a read of this thread here....
If its a "Tmous" HD2 (green and red call/hangup buttons) then you need to read this one
When connecting to the pc in bootloader you should see the word "serial" at the bottom of the screen change to "USB".......
Might be worth checking the text on you bootloader screen for any irregular looking characters, there have a few cases of people with corrupt bootloaders, usually these will display odd looking characters at the top. This is quite rare though.
If you want to flash another stock rom then you wont need to worry about HSPL just download the appropriate ROM and follow the instructions on screen.
Start off at the HTC site and input your serial number to see which ROM is suitable for your device.....
If none of that helps then hold out for some advice here from someone with better knowledge of these things.....
Ok well I've just tried to do the hard reset in the way you've described and had no response from the phone. I had to remove the battery from the back to actually power down the thing as nothing else seemed to work. I can't actually seem to start it up again now =S
Thanks for all the info, I'll keep trying to get it started. I'm downloading the stock rom from the htc site. Hopefully I will find a way to install that.
Also, when the bootloader was up, there weren't any odd characters that I could see. It all seemed pretty standard. It had the current rom driver which was 1.42 or something and a few other lines of info.
Thanks for the post.
edit: perhaps the battery is dead?
No problem.
Is it charging when plugged in and turned off?
If so let it charge while turned off for a while and then try to boot........
If you cant get to bootloader and establish a USB connection then you could try flashing the ROM from the SD card.
rename the rom to "LEOIMG.nbh" place it on the root of a freshly formatted (fat32) sd card and turn on the phone holding vol down..
conantroutman said:
No problem.
Is it charging when plugged in and turned off?
If so let it charge while turned off for a while and then try to boot........
If you cant get to bootloader and establish a USB connection then you could try flashing the ROM from the SD card.
rename the rom to "LEOIMG.nbh" place it on the root of a freshly formatted (fat32) sd card and turn on the phone holding vol down..
Click to expand...
Click to collapse
To be honest I have no idea if it is charging whilst turned off =S All I get is the bootloader when it decided to turn on and that gives no indication of power level so I really have no idea. It makes updating a rom pretty scary haha.
So I just attempted to install the default rom from teh htc site, but failed due to the lack of activesync. It was strange though because the updater managed to change the screen on the phone and get to 1%. It then crashed and I had to go through this recovery process.
I will have to try this SD card process I guess. Could you perhaps link me to a more in depth guide to how to do this?
Thanks a lot for your help I really appreciate it.
you should get a red light up near the earpiece to indicate that its charging........
try this video for flashing from sd card......
I am not getting a red light flashing? But it doesn't seem to be running out of charge. I'm still having lots of trouble
It would seem that I need to install this hspl before I do anything, however, I can't install that if I can only access the bootloader screen. Does this mean my phone is bricked?
I want to be able to set up a rom straight from SD, however, I have no idea where to start. That video just seems to send me in a big loop.
Perhaps you could link me to a simple rom that I can attempt to load via sd card?
edit:
I seem to have somehow fluked an install of HSPL 8G XE.
I have no idea how this happened or whether it is good or bad.. but at least something has happened.
Hmmm
installing hspl is covered here
as long as the word "serial" is changing to "USB" on the bootloader screen when you connect to the computer you should be ok.......
You dont need HSPL to flash via sd card but I think that video was directed more towards people installing cooked ROMS from XDA.
Installing a stock rom will automatically overwrite HSPL so unless your planning to flash a custom ROM then installing HSPL is pointless........
You might be better off installing a cooked rom. (Artemis, Dutty's)
They tend to run better than stock, if you get one running then it will be easier to get back to a stock rom (if you want to) than the situation your in now.....
This is from the flashing guide;
Flashing Via MicroSD Card
NOTE (PLEASE READ): If you flash a Stock Rom via microSD Card then it will overwrite your HardSPL with a stock SPL included in the nbh file. This does not apply to custom roms as they do not include an SPL. BE CAREFUL!!
1. Make sure your microSD is Formatted to fat32 (you dont have to delete all files but it is safer if you do)
2. Download your prefered Rom from the LEO Rom Develpoment Page and unzip/unrar it to your PC
3. Goto the Roms Folder and rename the .nbh file to LEOIMG.nbh
4. Copy the LEOIMG.nbh file to the root of your MicroSD Card
5. Plug the MicroSD Card into the phone
6. Reset the device while pressing the volume down button to enter the BootLoader screen, you will first see a tri-color screen with the phone and SPL Information at the top
7. Follow the On Screen instructions to start the update
8. After flash has completed, press the reset button with the stylus to reset the device.
Reckon you could link me to one of those roms? I think we're getting pretty close now.
Your help has been great I can't thank you enough.
Your welcome
You can find Dutty's ROM here
or the Artemis ROM here
Have a quick read and see which one you think you'll prefer, to be honest I think they're both pretty similar to stock but with a lot of the crap taken out....
Just follow the steps in the first link I posted and you should be good to go.
Ok new problems.. Can you believe it.
I seem to have tried everything.
Basically I can install of a sd card, but when it gets to the end of the install and I restart instead of booting into a OS it boots to the tri colour screen, and starts the install process again.
Also, I have attempted to install via usb and have had varying success.
As I have already said, I am able to install hspl, however, when I try to flash I get to varying percentages below 30% before the whole thing freezes.
I now have an error that says Upgrade Rom code error Please Try Again.
Sorry i dont mean to hijack ! but will any of you be kind enough to help me here..
http://forum.xda-developers.com/showthread.php?t=879980
thanks !
Ok so I followed the steps and still to no avail.
I am able to boot using the sd card method, however, the same problem occurs with each rom version. Basically as soon as I reset the device it pretty much switches itself off, then I can't turn it back on, once I finally do turn it on, it restarts the process like it never happened.
The other issue is again the active sync problem.
With most of the the usb connections I am able to connect and get a little way through the install (most I've got is 15%) then it just freezes up and I get the 262 error
Your best bet is to try flashing with a freshly formatted (FAT32) 4gb, class 2 card.
I know, sounds pretty specific right?
You wouldn't think it would matter?
I have tried flashing with 16 gb class 2, failed at the radio step
Tried with a 8 gb class 6, failed at the radio
4 gb, class 2, flashed successfully.
Seems our HD2's are picky about what cards they'll take a ROM from for some reason.
Alright I'll try that, my next issue is which is the stock rom for the phone =S
It was bought in the UAE and I'm currently in Australia.
edit: Also I read somewhere that the constant bootloader screen can be caused by a bent battery pin?
Edit2: I have attempted to do that, however, now the bootloader will accept the card, then just sit on loading...
I'm pretty sure this thing is bricked.
tombm said:
Alright I'll try that, my next issue is which is the stock rom for the phone =S
It was bought in the UAE and I'm currently in Australia.
edit: Also I read somewhere that the constant bootloader screen can be caused by a bent battery pin?
Click to expand...
Click to collapse
I've heard of bent battery pins being a pretty common problem, causing usually just the phone not to charge properly. I've personally never heard of it causing constant bootloader, but it's definitely worth checking.
It's weird that it's such a common problem, my usb/charging port is broken, so I have to use an external charger. I change my battery on average twice every 24 hrs, and I've never bent a pin
Ok, new info, apparently because the device is for the middle east it does not support stock 3.14 roms. What does this mean for me? Am I bricked.
http://forum.xda-developers.com/showpost.php?p=9614007&postcount=30954
Click to expand...
Click to collapse
That's the post I found the info in. All of that info matches up to mine except my original image was 3.142 I think =S
Firstly, your phone is not bricked - a bricked phone is responsive as a brick.
Can we start from the begining?
What does the Bootloader Moder screen say (with and without the USB cable connected)?
What ROM (and if custom ROM, what RADIO) have you flashed and are trying to flash?
fred_up said:
Firstly, your phone is not bricked - a bricked phone is responsive as a brick.
Can we start from the begining?
What does the Bootloader Moder screen say (with and without the USB cable connected)?
What ROM (and if custom ROM, what RADIO) have you flashed and are trying to flash?
Click to expand...
Click to collapse
Alright from the beginning.
Basically about a month into using the phone in Australia it became very unresponsive to the point where it would not boot at all. We left the phone for a couple of months, however, after seeing a friend rom android I decided maybe it was time to attempt to fix this phone.
Some more info:
When I attempt to do any sort of ROM update there is nothing in the 'current image' part so for example it will say update to Dutty 3.6 but it's updating from nothing, does this mean there's no firmware there?
In the bootloader I have:
PB81100 HX-BC
SPL-2.08.0000 8G XE
MICROP(LED) 0X05
MICROP(TOUCH) 0X40
Without USB cable in I get Serial in the white part down the bottom, with the USB cable in + plugged into computer I get USB.
Just to further clarify. In regards to the ROM I have installed. I simply don't have anything installed. There is a bootloader, no image, no bootup. It boots up to the tri colour, that's it.
For a moment we will forget about going to 3.14 ROM: I don't know if that phone is entitled to an official upgrade to 3.14, if it is locked to a particular network, if it is branded, etc. If it is not entitled to a 3.14 ROM upgrade then you will have to go through GoldCarding, so we will leave it for now.
Make sure that the battery has had a good couple of hours charge in the charger or double that if connected to the computer.
Remove SIM Card and SD Card.
Switch on to Bootloader Mode, then connect to USB.
Download and run HSPL2 - ignore the instruction about connecting to ActiveSync etc, just proceed.
Download and install the HTC 1.66 WWE ROM - again, ignore the instructions, just proceed.
The reason for HSPL is because your phone may be operator locked (not SIM locked) and you aren't entitled to run the 1.66 WWE ROM.

[Q] Help on fixing hd2 that wont boot up

Hey guys I have a hd2 that wont boot up anymore. I have installed several windows 6.5 cooked roms into this device for a while now. Recently this device has been given me a lot of problems until finally it took a dump. Now everytime i power up the device it stays in the splash screen. It doesnt even show radio version, rom version,etc on the bottom left of the screen. So is this hd2 dead or is there some way that i can fix it. I even tried installing tmobile's official rom on this device by going into the "rainbow screen" so that the device can be seen by using the usb cable, but alas....it didnt work either. So any help would be appreciated .
If it doesn't install, and nothing installs, then you need to take it to repair I guess.
I had a feeling about that. I just figured there was no way to fix it and the fact that i couldnt send it back to tmobile to get a replacement was out of the question since the firmware was modified. But your saying there are shops that fix these kinds of issues? If so, I better start looking around over here.
frequency1 said:
I had a feeling about that. I just figured there was no way to fix it and the fact that i couldnt send it back to tmobile to get a replacement was out of the question since the firmware was modified. But your saying there are shops that fix these kinds of issues? If so, I better start looking around over here.
Click to expand...
Click to collapse
why dont you try sd card method for flashing your rom !1! you can pm me if you need further help
Do you mean that it can't get to the boot loader screen (rainbow) or that trying to install a ROM from there didn't work? You might want to flash the original HSPL too, just to check.
What I mean is that everytime I boot up the hd2 it stays stuck on the splash screen. It doesn't even show the rom information in red at the bottom left corner of the screen. But I can boot to the tri color menu though. I have tried to install the tmous official rom by plugging the USB when I'm in the tri color menu and it always stays stuck at 9%. So is there way to fix this or am I screwed.
Sent from my Android Powered HD2 using XDA App
Try the sd-card recovery instead of the USB one.
http://www.jayceooi.com/2011/01/01/how-to-upgrade-htc-hd2-rom-through-sd-card-video/
After that, even if it fails, it shows only SPL in the tri-color screen then you are set to claim warranty.
frequency1 said:
Hey guys I have a hd2 that wont boot up anymore. I have installed several windows 6.5 cooked roms into this device for a while now. Recently this device has been given me a lot of problems until finally it took a dump. Now everytime i power up the device it stays in the splash screen. It doesnt even show radio version, rom version,etc on the bottom left of the screen. So is this hd2 dead or is there some way that i can fix it. I even tried installing tmobile's official rom on this device by going into the "rainbow screen" so that the device can be seen by using the usb cable, but alas....it didnt work either. So any help would be appreciated .
Click to expand...
Click to collapse
Well my bro... i think thats nand problems or heating issues ... does flashing rom goes all ok or it stops during flashing ? if stops than check if you phone is hot - hotter than normal.
Try this : Take out battery, memory card, sim card and put you phone in the fridge for about 5-10 min ( dont worry tried many times... no harm ) meanwhile prepare your sd card to flash rom with sd card method ... to do that extract Ruu rom - stock one - download with hd2 serial nr ( winrar, 7zip etc) find Ruu_Signed.nbh rename it to LEOIMG.nbh than copy to sd card ( format you sd card fat32 and make sure it works ... 2gb will work ) take phone out from fridge put sd card & battery into phone power one phone while holding volume down key ( go into tricolor screen - bootloader) and follow procedure in phone... i hope everything goes well and you fix you phone... but if still no success than flash android or wp7 ( if you have warranty flash stock SPL and return phone).
best regards from me

my htc hd2 is STUCK.. HELP ME PLS

I bought an HTC HD2 FEW WEEKS BACK FROM ONE OF MY FRIEND.
I DO NOT HAVE THE HISTORY OF WHAT HE TRIED TO DO WITH IT.
BUT BECAUSE IT WAS STUCK/DEAD , HE GAVE TO ME FOR CHEAP.
NOW THIS PHONE IS UNDER WARRANTY TILL AUG-2012 AND IS FROM VODAFONE.
(EVEN AFTER INSTALLING ANDROID IT IS VOID)
HE MUST HAVE TRIED SEVERAL ROM/HSPL TO GET TO THIS POINT.
PROBLEM:
When I power up the phone, it displays a NRG LOGO SCREEN (energize software), and it gets stuck on it forever.
When I do hold the volume down + power button, then it comes up with the three colour screen and it says SPL-2.08.0000, AND also says rom update failed (only if i try to install and then start up)
The phone does connect through USB when it is on the three colour screen, but it does not let me install ANY OF THE romS or the spl'S...
I have tried literally every single step possible. I have tried to do task 29, i have tried install the original rom, i have tried to put the rom in the sd card and try it that way.. I have also tried to do hard reset... vol up and down and it does not complete either..
I best rom it let me install was 99% of 2.10.50.19.2.. but after 99% it got stuck .. it seems like it gets stuck within 1 min or so.. anything you do!
Some times after several hundred attempts, it does let me change the spl... as it was displaying 3.... before then i changed to 1.4..... and then to 2.08...
All i want to do is to get rid of the NRG SCREEN, so i could send to the htc ,, for repair ( i know that it is not under warranty if i used andriod, but they will not know) .. or is there any way to completely format the phone,,, is there any solution to install andriod or microsoft? pls help
Before we start, you can ask him how his device has ended up like this, can't you?
boxboy said:
I bought an HTC HD2 FEW WEEKS BACK FROM ONE OF MY FRIEND.
I DO NOT HAVE THE HISTORY OF WHAT HE TRIED TO DO WITH IT.
BUT BECAUSE IT WAS STUCK/DEAD , HE GAVE TO ME FOR CHEAP.
NOW THIS PHONE IS UNDER WARRANTY TILL AUG-2012 AND IS FROM VODAFONE.
(EVEN AFTER INSTALLING ANDROID IT IS VOID)
HE MUST HAVE TRIED SEVERAL ROM/HSPL TO GET TO THIS POINT.
Click to expand...
Click to collapse
Sir, you have forgotten your caps locked.
boxboy said:
PROBLEM:
When I power up the phone, it displays a NRG LOGO SCREEN (energize software), and it gets stuck on it forever.
When I do hold the volume down + power button, then it comes up with the three colour screen and it says SPL-2.08.0000, AND also says rom update failed (only if i try to install and then start up)
Click to expand...
Click to collapse
Because you have stock SPL, you won't be able to install any custom ROM or any stock ROM not made for your region/SN.
boxboy said:
The phone does connect through USB when it is on the three colour screen, but it does not let me install ANY OF THE romS or the spl'S...
I have tried literally every single step possible. I have tried to do task 29, i have tried install the original rom, i have tried to put the rom in the sd card and try it that way.. I have also tried to do hard reset... vol up and down and it does not complete either..
Click to expand...
Click to collapse
AFAIK, task29 is, also to be considered, a custom rom so it needs HSPL to be flashed. Are you sure you have followed the steps correctly?
boxboy said:
I best rom it let me install was 99% of 2.10.50.19.2.. but after 99% it got stuck .. it seems like it gets stuck within 1 min or so.. anything you do!
Some times after several hundred attempts, it does let me change the spl... as it was displaying 3.... before then i changed to 1.4..... and then to 2.08...
Click to expand...
Click to collapse
That is not a ROM, it's a radio. You need to flash HSPL to be able to change the splash screen (NRG Screen). HSPL should go like this: SPL 2.08.HSPL .
boxboy said:
All i want to do is to get rid of the NRG SCREEN, so i could send to the htc ,, for repair ( i know that it is not under warranty if i used andriod, but they will not know) .. or is there any way to completely format the phone,,, is there any solution to install andriod or microsoft? pls help
Click to expand...
Click to collapse
Microsoft is a corporation, Windows Phone is the OS .
One more thing, to be able to flash a LEOIMG from sd, the .nbh must be a rom that is compatible with your device (It will work if you get it from htc.com using the device's serial number)
I hope this helps. And I'm sorry if I am incorrect at something.
Good luck.
------------------------------------------------------------------------------------------------------------------------------------------------
To summarize it, you need to do either one of the following:
1- Install HSPL, and do what you want.
2- Go to HTC.com, download a rom using your Serial Number, rename file to .zip, extract the .nbh file, rename to LEOIMG.NBH [Capital letters], put onto sd card and insert into phone, boot up device while holding volume down ONLY, and make sure splash is removed and you're back to the "htc" stock, then send to repair [why?].
posting teh same post in multiple sub forums is considered rude
http://forum.xda-developers.com/showthread.php?t=1440265
Yeah, HSPL is needed for flashing pretty much everything. One thing you could do would be to flash a stock ROM from your SD card (just google it I CBA to provide links and stuff) which would reset everything to factory WinMo (including SPL to SPL3.03 [assuming you flash the latest ROM 3.14]) and from here it would basically be a fresh start. Probably the safest route without HSPL
Hi.
Thank you for your replies...
Let me tell u guys if I forgot to say earlier. The mobile phone is not letting flash any of the Hspl... be q series, 2 series or 3.series... all the times it says error 0000006 and 000000010 etc... a couple out of hundreds it did let flash but then it doesn't let me flash the factory rom fom HTC.
I have succesfuly flashed the 3.03 hspl... bit still no success in flashing any roms ... it gets stuck sometimes at 99% and sometimes at 0% and sometimes it comes up with a scrambled screen and stuck
OK,
My final.outcome.
This phone let's me flash the hspl but it doesn't let me flush any roms including the original HTC factory rom.
I can also perform the task 29. Etc but still the NRG screen is still there.
I would like to know that if I flash the original Split and send it HTC, will be repairable for free? Sure? Even with the NRG.
now i think the only option available to you is jtagging the device which may permanently void the warranty !!
it had happened with me once, but somehow it got solved !
i used to randomly install clk, magldr, radios, hspl etc multiple times !
it used to get stuck while installing and then i used to remove the battery and try again !!
somehow it started ! !!
STRANGE DEVICE !!
Yeap its a real problem!!
Now , It will not let me change the hspl to spl whatsoever I do.
I would like your suggestions
I bought this brick for £50 and I can return it to get my money back. Has any used jtagging and does it 100% work?. The thing is if I do used jtagging, and if it doesn't work ,then I can,t return it!. How much does it cost and is it worth it?
jtagging will solve your problem !!
they remove the motherboard of the device and flash the os into the motherboard directly through a device named riff box !!
refer this video for more info !!
http://www.youtube.com/watch?v=zElsUERTzOU
but pls do not try this at home ! !!
just contact a local repair shop to jtag your device !!
also u can contact these guys from the video !!
good luck ! !!
boxboy said:
I have succesfuly flashed the 3.03 hspl... bit still no success in flashing any roms ... it gets stuck sometimes at 99% and sometimes at 0% and sometimes it comes up with a scrambled screen and stuck
Click to expand...
Click to collapse
Check that the micro USB connection isn't "wobbly".
I had a TMOUS HD2 and never had any issues. Then, I sold it and got a Telstra HD2 and had big issues getting ROMs installed until I realized that the connection at the phone was a little weak. I can't send any updates to WP7 via cab sender unless the phone is in a certain position to keep the connection from breaking.
boxboy said:
I bought an HTC HD2 FEW WEEKS BACK FROM ONE OF MY FRIEND.
I DO NOT HAVE THE HISTORY OF WHAT HE TRIED TO DO WITH IT.
BUT BECAUSE IT WAS STUCK/DEAD , HE GAVE TO ME FOR CHEAP.
NOW THIS PHONE IS UNDER WARRANTY TILL AUG-2012 AND IS FROM VODAFONE.
(EVEN AFTER INSTALLING ANDROID IT IS VOID)
HE MUST HAVE TRIED SEVERAL ROM/HSPL TO GET TO THIS POINT.
PROBLEM:
When I power up the phone, it displays a NRG LOGO SCREEN (energize software), and it gets stuck on it forever.
When I do hold the volume down + power button, then it comes up with the three colour screen and it says SPL-2.08.0000, AND also says rom update failed (only if i try to install and then start up)
The phone does connect through USB when it is on the three colour screen, but it does not let me install ANY OF THE romS or the spl'S...
I have tried literally every single step possible. I have tried to do task 29, i have tried install the original rom, i have tried to put the rom in the sd card and try it that way.. I have also tried to do hard reset... vol up and down and it does not complete either..
I best rom it let me install was 99% of 2.10.50.19.2.. but after 99% it got stuck .. it seems like it gets stuck within 1 min or so.. anything you do!
Some times after several hundred attempts, it does let me change the spl... as it was displaying 3.... before then i changed to 1.4..... and then to 2.08...
All i want to do is to get rid of the NRG SCREEN, so i could send to the htc ,, for repair ( i know that it is not under warranty if i used andriod, but they will not know) .. or is there any way to completely format the phone,,, is there any solution to install andriod or microsoft? pls help
Click to expand...
Click to collapse
Don't worry ... you can give the life to your phone back... it shows fail bcus u have 2.08.0000.. so it means u Sud have 2.08 v hspl.. so try flashing hspl by getting into bootloader(3 colour) by pressing volume down + power Then flash hspl.. but remember select 2.08v.. then again after flashing hold volume down + power.. bootlooder.. then flash magdlr 1.13 ... now the phone will boot into a black screen with written mangdlr.. wen the black screen magdlr screen comes then press power off for 5mintzz.. follow the guide to flash.. there is a stick thread in NAND DEVELOP... U can get the windows version back to your phone to get the warranty...
Sent from my HTC HD2 using Tapatalk
Ok ,, some good new at last ..
I have used the HSPL4 to change my 3.03hspl to 3.030000 spl...
Success, as when i go to the tri colour screen it says spl and no hint of hspl...
Bad news, is that i still cant get the rom flashing,, as it gets stuff at some point and mostly at 99%.. Have tried both ways through SD (leoimg) and through USB.
Now final question is ... When i on the phone a big logo of NRG (ENERGIZE) writtten comes up and it gets stuck there.. the phone has SPL .. so it still under warranty to return it?.. I still have all the void sticker intact.
boxboy said:
Now final question is ... When i on the phone a big logo of NRG (ENERGIZE) writtten comes up and it gets stuck there.. the phone has SPL .. so it still under warranty to return it?.. I still have all the void sticker intact.
Click to expand...
Click to collapse
did you try to flash just a splashscreen as i suggested in your other thread? (they can be flashed alone, no need for a whole rom, , just like radios)
if you can get a stock splashscreen on there you are sorted.
Maybe try to download the original Software from HTC.
With you serial number you can get the latest windows for this phone.
Flash the Software you get from HTC.
If this is working ok you can try to install any Android ROM.
Read at first this
http://forum.xda-developers.com/showthread.php?t=905841
Try to understand and follow the steps..
But if you have even no luck with original Windows soft. You will also (maybe) have a lot of probs. with Android..
Thank you guys for all your help..
I have flashed andriod on several phones some time ago and I actually forgot the right steps to follow.
But this phone is unique is not letting me finish.
After following all the right steps, i wasnt able to install a rom succesfully even after installing the HSPL... and I am also not able to install the factory rom from htc on either the hspl or spl settings.
But i now got rid of the NRG screen and I have also installed the spl 3.03.. When you on the phone, it displays software upgrade failed..
So I have now sent the mobile to HTC as it is under warranty. I will then re-flash andriod following the right steps and see what happens!
Thanks again!
My mobile came back from HTC with a week.. Looks like a brand new one!
In the letter it says the replaced IMEI, PCBA, FL BD, W/O_ REGIONAL_ID, LEO
WOW
GREAT PHONE... ITS MUCH FASTER THAN THE PREVIOUS ONE FOR SOME REASONS

Categories

Resources