Hi all,
I'm trying to flash my device to USPL v2.5 but, when I run the GUI, the application gets stuck and nothing happens on my device...
Currently, my device has the following configuration:
ROM version: 1.56.401.0 (43972) WWE
ROM date: 03/06/09
Radio version: 1.13.25.24
Protocol version: 52.62.25.34U
The bootloader screen shows:
BLAC100 32M
SPL-1.54.0000
MicroP-BlackStone (LED) v6
And at the white frame, when I plug the USB cable the text USB shows up.
What am I exactly trying to do?
Upgrade from WinMo 6.1 to WinMo 6.5
I'm following a tutorial from the forum but, I can't pass through the first step (flash the USPL bootloader)
As far as I understood, I must change the bootloader to continue to flash the new ROM... right?
The host computer I'm using for the process is running Windows 7 Ultimate version and, I have already tried to boot with "disable driver signing enforcement" option.
The question is:
Could somebody help me with this problem?
Many thanks,
Adilo
Related
Hi,
I am also using a wizard, K-Jam, and I need some help from you guys.
Several month ago, when I tried to flash its rom, without much knowledge on flashing roms, I accidentally used MTTY to DOCTEST the rom, which according to the threads I was following, was to "format" the rom. Then I flashed it with Custom RUU 1.01.
The phone works well after that except the IPL becomes forever 1.01, no matter what kind of rom flashed. The SPL can be upgraded or downgraded without problem.
So, now the phone is
=> Bootloaders:
IPL: 1.01 (G3 device)
SPL: 3.08 (G3 device)
Built on Nov 13 2006 at 14:02:18
Copyright (c) 2003 High Tech Computer Corporation
=> Firmware:
OS: 5.2.xxx (Build 19839.kosky\xc8~\xd3~Hr.)
ROM: 5.2
Registry AKU: .kosky\xc8~\xd3~Hr.
Radio: 02.69.11
Protocol: 4.1.13.30
It seems the IPL is locked at 1.01. Can anyone help to solve this?
Another issue is the Wifi. When I flash it back to Custom wm 5.0 rom1.01 (IPL/SPL1.01), the Wifi works fine. Everything(WLan mode, MAC, etc.) is pre-set. But when I flash it to other roms, I can't turn on the Wifi, either through Commanager, or Settings>Connection. When I tap the WLan button, the process indicator goes on for a while and then off, the Wlan is still off. Impossible to input the WLan settings.
I wonder if the Wifi problem is caused by the IPL locking.
I do need help and advice from you guys, thank you very much!
Hi,
I have htc polaris (pola100)
but I unwillingly flash spl version 3.13.000 but now doesn't go anythink flash,
don't go flash anythink other spl version (1.25.0000, 1.28.0000)
Please anybody help me.
You had to flash the original ROM of your Polaris before flashing the Original SPL.
Can you get the tricolor screen?
I have original spl but after I flash hard-spl v2 and flash not original rom,but this rom was very bad.
So I would back my original wm6.1 rom htc, so i find original three original spl (1.25.0000 1.28.0000 3.13.0000) I flash spl 3.13.000 but now doesnt flash anythink anythink spl and anythink rom
please and now?
(ps: sorry my english is bad)
but yes a see my bootloader , i see red blue green and white color
on the left side is write:
POLA100
SPL-3.13.0000
CPLD-2
and the right side is write:
RUUNBH
okay, I understand.
Isn't there any ROM flashed?
i tried rom:
3LIT3_VI_Full
udK_Syrius_R7_WWE
c_shekhar_Pola_WM3.13.755CS_Build20755_Public_Final
and original rom htc wm6.1
But all roms frozen near 0% on htc display
I think you've bricket your phone
but on this list:
http://forum.xda-developers.com/showthread.php?t=351964&page=28
he have same problem as I.
mtelleria mtelleria is offline
Junior Member
Join Date: Jun 2008
Posts: 6
Default Problems installing HardSPL
Hi,
I have installed the last official version on WM6.1 on my htc, now i want to install one custom rom from this forum.
I tryed to istall first HardSPL, but i don't know why, the process get stuck at 0% of the istall and never continue.
In the 3 color screen appear:
POLA100
SPL-3.13.0000
CPLD-2
Someone can help me?
Thanks
____AND THIS ALSO BUT OTHER SPL:
he write:
"donchischotte" donchischotte is offline
Junior Member
On the screen I read:
-------------
RUUNBH
POLA100
SPL-1.28.0000
CPDL-2
--------------
Here is what I do and what happens when I try to use HARD-SPL V2:
1) I connect the USB cable and the writing on the device changes from "serial" to "USB"
2) I run romupdateutility
3) I check "I understand..." + next
4) I check "I completed..." + next
5) on the PC a message "verifying the information on your PDA phone, please wait" appears and after a while the device switches to a screen with a progress bar at 0%, while on the PC the following message appears:
--------------------------------------------------------------
Current information about your PDA phone:
Image version:
Select from below:
UPDATE Update the current ROM version
--------------------------------------------------------------
6) I click UPDATE and the following appears:
------------------------------------------------------------------
Verify that you want to update the ROM version:
From:
Image version:
To:
Image version: OliNex-2.20
------------------------------------------------------------------
7) I press "next" twice and I get the message "updating the ROM image on your PDA phone", but the progress bar is stuck at 0% and after a minute or so i get the ERROR[262] : UPDATE ERROR
I tried usinr both Vista and XP, with or without MicroSD and SIM card. It's always the same.
I tried flashing different SPLs (even the two original ones) with the same problem. If I try to flash a ROM I get the ERROR [294] : INVALID VENDER ID"
after 1% progress.
I HAVE SAME PROBLEM
I think you must wait Olipro or another chef here to say you how to refalsh SPL with 2.40 version in command line
You can try to flash you original ROM via SD-Card.
what is the solution ? I have the same problem with :
SPL-3.13.0000
I can't flash ...
Now its workhttp uff;-)
I flash my polaris 10* and all of a sudden work.
Hi all!
First the first: this is my first post!
I have a HTC Touch HD and I tried to upgrade the ROM from 1.56.401.0 (official upgrade from htc.com) to (for example):
EnergyROM_BLACKSTONE_20090921_StandardM2.5
Or
Miri_WM65_21857_Premium_Manila_2.5_REV8.0
I have ALLWAYS the same error... (see images!).
http://img5.imageshack.us/i/romerror.jpg
http://img197.imageshack.us/i/romupdate.jpg
"Error [262]: UPDATE ERROR"
And then the phone works normally...
Any answers? I really want to try Windows Mobile 6.5!!!!
Thanks!!!!
it's prolly cause you never changed your SPL, but follow this guide:
http://forum.xda-developers.com/showthread.php?t=505377
The rom is 1.56.401 (after going to: Start > Settings > System tab > Device Information).
But when i am i bootloader mode:
BLAC100 32M
SPL-1.54.0000
MicroP-BlackStone (LED) v6
So how i can update to the 1.56 SPL and then use HSPL to flash ?
Thanks!!!
Again, follow the dummies guide I linked above, it has everything answered
Yeah! running "EnergyROM_BLACKSTONE_20090921_StandardM2.5" now!
Thanks!!!!!!!!!!
Hello folks,
My device is a QTEK A9100.
After updating my rom to one with WM6.5 I noticed that my boot screen now looks like a gradient from green to black like the picture attached.
The problem is that the phone now doesn't activate de radio. It show no signal and when I try to enable the phone in comm manager, it doesn't enable it.
So I decided to go back to WM6.1. Right now I'm using X2H's WM6.1 Manila UI - http://forum.xda-developers.com/showpost.php?p=3459150&postcount=8
Also, the battery light is not staying lit when the usb or power cable are connected and active sync is not detecting the phone. Also the phone less responsive then usual.
IPL/SPL version are shown as follows in the boot screen:
IPL: 2.21.0001
SPL: 2.21.olip
<-- blank line
OS: 6.1.0.0
Settings > System > Device Information shows in the Version tab:
ROM version: 6.1.0.0 WWE
ROM date: 1/16/08
It does not show radio or protocol version as I saw in another screen shots.
Any ideas on how to enable the radio and make active sync detects the phone?
help anyone?
the blank line at the boot can mean there is the corrupt radio or something similar...the radio version is showed there
i think the best way is try an hard reset, and if it don't work the way is flash a radio...
Hard Reset didn't work.
Tried to install radios 3.02.11 and 2.69.11 and nothing.
The rom install finishes without error but after the device resets it looks like the same it was before. It show no GSM version at the boot screen and the boot screen keep showing for almost 2 minutes.
reflash your stock rom.
josefcrist said:
reflash your stock rom.
Click to expand...
Click to collapse
Thanks, I did it and still the same.
Now the IPL and SPL are version 2.22.0001
But the green boot screen remains and still not show the GSM version.
The WM is laggy and at the device information screen I can only see the rom version, the rom date and the ext rom version.
No information about protocol or radio version.
It seems that no matter what radio I flash, it's not stored in the device.
Any other ideias?
After I tried to get my stock SPL back the phone it's not working anymore.
Always it starts in boot mode and Displaying this Message:
In the Right corner:
RUUNBH
Then I have:
BLAC100 32M
SPL-1.14.0000
MicroP-BlackStone (LED) v6
And after:
Upgrade ROM code error
Please try again
and if I do not have th sd carin at the bottom I have :
Serial
I have to say that I am running Windows 8 x64.
Please help me I really appreciate that!
PS: I have searched in the forum I cannot find any specific solution that worked for me.
Most, if not all, custom ROM (WM 6x) is not supported by the stock SPL 1.14.
I thought you had already flashed SPL 1.56 Olinex.
http://forum.xda-developers.com/showthread.php?p=41134106#post41134106
http://forum.xda-developers.com/showthread.php?p=41079640#post41079640
My recommendation is to revert back and re-flash HSPL 1.56 Olinex. See this link:
http://forum.xda-developers.com/showthread.php?t=505377&highlight=flash+hspl
Follow the steps patiently and carefully.
Make sure you login to Windows with an account that has Admin rights.
Remove your microSD from phone when you are flashing HSPL.
Sometimes you may have to do it a few times to get it right. At the end, your bootloader will say:
BLAC100 32M
SPL-1.56.0 Olinex
MicroP-BlackStone (LED) v6
At the white portion at the bottom, you will see Serial but it will change to USB if you connect it by USB cable to the PC.
I believe you do not have to re-flash the WM6x ROM. (I did not need to when I upgraded my SPL from stock 1.54 to 1.56 Olinex.
But if you still cannot run WX after the SPL 1.56, then you need to re-flash the WM6x ROM from microSD.
chan.sk said:
Most, if not all, custom ROM (WM 6x) is not supported by the stock SPL 1.14.
I thought you had already flashed SPL 1.56 Olinex.
http://forum.xda-developers.com/showthread.php?p=41134106#post41134106
http://forum.xda-developers.com/showthread.php?p=41079640#post41079640
My recommendation is to revert back and re-flash HSPL 1.56 Olinex. See this link:
http://forum.xda-developers.com/showthread.php?t=505377&highlight=flash+hspl
Follow the steps patiently and carefully.
Make sure you login to Windows with an account that has Admin rights.
Sometimes you may have to do it a few times to get it right. At the end, your bootloader will say:
Remove your microSD from phone when you are flashing HSPL.
BLAC100 32M
SPL-1.56.0 Olinex
MicroP-BlackStone (LED) v6
At the white portion at the bottom, you will see Serial but it will change to USB if you connect it by USB cable to the PC.
I believe you do not have to re-flash the WM6x ROM. (I did not need to when I upgraded my SPL from stock 1.54 to 1.56 Olinex.
But if you still cannot run WX after the SPL 1.56, then you need to re-flash the WM6x ROM from microSD.
Click to expand...
Click to collapse
Thank you very much for your answer!
I cannot run the uspl, blacuspl in Windows 8. Is there any change to run the blacuspl on WIndows 8?
It sais USB on phone's screen...
I wanted to install a spanish rom and cannot fint a 6.5 that is compatible with Olinex 1.65
chan.sk said:
Most, if not all, custom ROM (WM 6x) is not supported by the stock SPL 1.14.
I thought you had already flashed SPL 1.56 Olinex.
http://forum.xda-developers.com/showthread.php?p=41134106#post41134106
http://forum.xda-developers.com/showthread.php?p=41079640#post41079640
My recommendation is to revert back and re-flash HSPL 1.56 Olinex. See this link:
http://forum.xda-developers.com/showthread.php?t=505377&highlight=flash+hspl
Follow the steps patiently and carefully.
Make sure you login to Windows with an account that has Admin rights.
Sometimes you may have to do it a few times to get it right. At the end, your bootloader will say:
Remove your microSD from phone when you are flashing HSPL.
BLAC100 32M
SPL-1.56.0 Olinex
MicroP-BlackStone (LED) v6
At the white portion at the bottom, you will see Serial but it will change to USB if you connect it by USB cable to the PC.
I believe you do not have to re-flash the WM6x ROM. (I did not need to when I upgraded my SPL from stock 1.54 to 1.56 Olinex.
But if you still cannot run WX after the SPL 1.56, then you need to re-flash the WM6x ROM from microSD.
Click to expand...
Click to collapse
Thank you very much ! that driver update was the bad thing. I follow your instructions and it's works fine !
Thank you again !
oliviu said:
Thank you very much ! that driver update was the bad thing. I follow your instructions and it's works fine !
Thank you again !
Click to expand...
Click to collapse
I'm glad it turns out fine for you. All custom ROMs 6.5x (as well as Android 2.x) for Blackstone will need SPL 1.56+. Presently, it seems that this 1.56 Olinex version is probably the only stable one and last to be developed for this phone. There are already so many other alternative phones at the same price range but with higher specifications so I don't think many people will want to buy this phone (new) anymore.
The phone hardware (processor, memory) is pretty much limited to WM 6.5x, or Android 2x, so we will have to live with it. The only other alternative is to get a newer phone.
And hey, don't forget to press the Thanks button, for any contributions from this forum, if you find them helpful or useful.