Related
Since then voila I install a rom for the first time I have a bug here is a picture to help you understand
It is an image that I have requests in the forum but am in all its images
More information please!
We need more information!
Are you using SPL or USPL?
What ROM did you flash?
Did you perform a hard reset after flashing the ROM?
If you're not sure about the above then read this for SPL:
http://forum.xda-developers.com/showthread.php?t=431217
This for USPL:
http://forum.xda-developers.com/showthread.php?t=462347
And this is an all round overview:
http://forum.xda-developers.com/showthread.php?t=505377
G
Edit: And this post makes me a senior member - woohoo!
Here is how I do I install rom always full of the same problem
Olinex I install 1.56 and then the official 1.56 rom 2009
The picture you supply isn't from the official 1.56 HTC ROM because it is running Windows mobile 6.5 (I can tell from the user interface). The official ROM uses Windows Mobile 6.1.
I think you need to make sure that you flashed the correct ROM and then flash the device again. After doing this make sure you hard reset afterwards at least once, preferably twice by holding down both volume buttons while powering the device on.
Also unless you have a CID locked phone that is branded eg. Orange, you shouldn't have to use Olinex HSPL and can download the official ROM from here:
http://www.htc.com/uk/SupportDownload.aspx?p_id=179&cat=2&dl_id=533
In any case you should confirm which SPL you have by holding down the lower volume button while booting (it will tell you either SPL or HSPL along with version number).
Let us know how you get on...
G
HSPL 156 OliNex and htc is a factory not orange or other
Okay, it sounds like you have successfully installed HSPL, but now you need to try flashing the ROM again (it appears to be the ROM that is causing the graphic corruption in your picture).
Make sure you perform two hard resets after flashing and hopefully this should solve your problem...
Cheers,
G
P.S. Make sure you back everything up prior to re-flashing as you will lose everything in phone memory (SD card should not be affected, but my advise would be to remove it anyway until you have re-flashed).
Where do i find it?
Searched for a long time
Why do you need it?
You can't get it on it's own, you need to flash a stock ROM using the SD card method to get the stock SPL on. If you turn off your phone, hold down the vol down button and turn it on you go into the bootloader - what SPL version is listed in there?
(to get out of the bootloader, take the battery out for 5 seconds and put it back in)
my spl: 1.66.0000
i have updated my hd2 rom once (original update).
You'll need to get a 1.48 ROM and flash back to that using the sd card method to get back to SPL 1.42. Then you can put HSPL on the phone and upgrade again using the activesync method and you'll be ok.
You can get the 1.48 ROM here, just put in your serial number:
http://www.htc.com/nl/SupportDownload.aspx?p_id=297&cat=2&dl_id=804
Then follow these notes:
Flashing Via MicroSD Card
NOTE (PLEASE READ): If you flash a Stock Rom via microSD Card then it will overwrite your HardSPL with a stock SPL included in the nbh file. Therefore if you flash a v2.01 or later Rom (with SPL2.*) you will NOT be able to reinstall HardSPL onto your device and could end up bricking it. This does not apply to custom roms as they do not include an SPL. BE CAREFUL!!
1. Make sure your microSD is Formatted to fat32 (you dont have to delete all files but it is safer if you do)
2. Download your prefered Rom from the LEO Rom Develpoment Page and unzip/unrar it to your PC
3. Goto the Roms Folder and rename the .nbh file to LEOIMG.nbh
4. Copy the LEOIMG.nbh file to the root of your MicroSD Card
5. Plug the MicroSD Card into the phone
6. Reset the device while pressing the volume down button to enter the BootLoader screen, you will first see a tri-color screen with the phone and SPL Information at the top
7. Follow the On Screen instructions to start the update
8. After flash has completed, press the reset button with the stylus to reset the device.
Wiki and Sticky....
Hey There,
Look to the WIKI and STICKY
All you need is there.... yeah with a real video for beginners...
Grtz,
PS MOD close this....
thnx i know how to get it done now!
Thank you EddyOS, i will also try this since i get "invalid vendor ID" when doing it via USB cable. Hope it works
EDIT: Dang, didnt work "Loading ... Not Allow" + back to bootloader
Help
Hi,
I need to find SPL 1.42.0000 for my leo, swedish.
The link in the previous post didnt work for my SerialNo =(
you can't get just the SPL - you need to flash the stock ROM for your region.
and the link wouldn't work as it was the Dutch HTC site - try here:
http://www.htc.com/se/supportdownloadlist.aspx?p_id=297&act=sd&cat=all
Taken from my Rom Flashing guide:
2. FLASH HARDSPL2 (REQUIRED!! DO THIS BEFORE ANYTHING ELSE)
The Original HardSPL Thread is *HERE*
IMPORTANT: To install/uninstall this HSPL there must be any SPL version from this list on your device:
SPL 1.42.0000, SPL 1.42.HSPL, SPL 1.62.0000, SPL 1.66.0000, SPL 1.66.HSPL,
SPL 2.07.0000, SPL 2.08.0000 SPL, 2.08.HSPL
NOTE: If you have Vista or Windows 7, update WMDC to v6.1 *HERE* first
NOTE: Turn OFF any AntiVirus Program first as it WILL interefere with the flash (there is NO harmful code in the program)
Flashing via ActiveSync with USB Lead (thanks to Bepe)
1. Download HardSPL package from *HERE* and extract to an empty folder
2. Synch Phone with PC in Windows Mobile!!! It has to be connected to activesync or WMDC via USB cable
3. Run HSPL2_RUN.exe from your pc and read all the text carefully
4. When finished click next in the HardSPL program
5. The program will now check the usb connection and enter the bootloader screen (tri colour)
6. NEW: YOU CAN NOW CHOOSE WHICH VERSION OF SPL OR HARDSPL YOU WANT TO FLASH TO YOUR PHONE!!
7. Select your desired HardSPL and click NEXT.
8. HardSPL will now be flashed to your phone.
5. When its finished the HardSPL program will pop up a box saying "successfully Done".
6. Click ok to terminate program and reboot the phone.
7. Congrats, you just flashed HardSPL.
EddyOS said:
you can't get just the SPL - you need to flash the stock ROM for your region.
and the link wouldn't work as it was the Dutch HTC site - try here:
http://www.htc.com/se/supportdownloadlist.aspx?p_id=297&act=sd&cat=all
Click to expand...
Click to collapse
You can flash just the SPL now
Mark.
Spl 1.42.0000000000
Could someone Just send us the link to where this stupid SPL 1.42.00000 that everyone needs for it to work is? We can't find it anywhere????
Where is it?
We not how to load it we need the file!!!!
[email protected] said:
Could someone Just send us the link to where this stupid SPL 1.42.00000 that everyone needs for it to work is? We can't find it anywhere????
Where is it?
We not how to load it we need the file!!!!
Click to expand...
Click to collapse
you are showing your ignorance by getting all demanding, if you had read anything, you would know that spl is part of all official roms.it is not a file in its own right.
the only reason you would be looking for it is if you have a telstra, cos hspl2 works on any spl. in which case you need the 1.49 telstra rom, flash it from sd card and it will downgrade your spl to 1.42
if you don't have a telstra, then you are looking for something you don't need.
i cannot seem to flash my phone! D: it's irritating me greatly...
allow me to tap out my phone for you.
rgb screen:
PB81120 SS-B3
SPL-2.08.0000 8G XE
MicroP(LED) 0x05
MicroP(TOUCH) 0x40
i can't flash roms till it's hspl-ed.
hspl2 says i have a bad model number?
i have the US TMO HD2, 512 rom, not 1gb rom.
pretty sure it's only 512, cause with OS running, i check about system, it says i have 4hundred and something avail.
i've tried everything.
i can't even locate a copy of 1.66 rom so i can install 1.42 spl, cause htc says my model number isn't suitable for the rom i try to download.
basically, i'm F%$KED. and i need helps.
please, respond! i just wanna hack this POS winmo 6.5 shiz to something cooler.. D:
ijoshv2 said:
i cannot seem to flash my phone! D: it's irritating me greatly...
allow me to tap out my phone for you.
rgb screen:
PB81120 SS-B3
SPL-2.08.0000 8G XE
MicroP(LED) 0x05
MicroP(TOUCH) 0x40
i can't flash roms till it's hspl-ed.
hspl2 says i have a bad model number?
i have the US TMO HD2, 512 rom, not 1gb rom.
pretty sure it's only 512, cause with OS running, i check about system, it says i have 4hundred and something avail.
i've tried everything.
i can't even locate a copy of 1.66 rom so i can install 1.42 spl, cause htc says my model number isn't suitable for the rom i try to download.
basically, i'm F%$KED. and i need helps.
please, respond! i just wanna hack this POS winmo 6.5 shiz to something cooler.. D:
Click to expand...
Click to collapse
Maybe this posting here will help you to get answers to your questions...
htc hd 2
is not working for mi my freind , it just get the color on the phone and them the program say error , can you help me my SPL-2.08.0000
walasquin55 said:
is not working for mi my freind , it just get the color on the phone and them the program say error , can you help me my SPL-2.08.0000
Click to expand...
Click to collapse
do you have a tmous phone? in which case you need hspl1024 (see my sig)
if not, try different usb ports, especially try to use one around teh back of the computer
also, dont forget to right click hspl and 'run as administrator'
nO it does not work that way!
Would be a lot easyer if you just gave us the file 1.42.0000.nbh so we could add it to our SDcard and flash it without it locking or not working! Please I beg you send us over the 1.422.0000 file all by itself!
PLEASE!!!!
tictac0566 said:
Maybe this posting here will help you to get answers to your questions...
Click to expand...
Click to collapse
I have the same problem and so does everyone else, they no the files don't work and they won;'t give us the EXACT 1.42.0000.nbh file so we can SD card flash it!
It would be so simple!!!!!!
ok then
samsamuel said:
you are showing your ignorance by getting all demanding, if you had read anything, you would know that spl is part of all official roms.it is not a file in its own right.
the only reason you would be looking for it is if you have a telstra, cos hspl2 works on any spl. in which case you need the 1.49 telstra rom, flash it from sd card and it will downgrade your spl to 1.42
if you don't have a telstra, then you are looking for something you don't need.
Click to expand...
Click to collapse
How come someone sent over a SPL 2.08.0000 which mine used to be 2.10.0000 and that worked just fine, why wouldn't sending over a file 1.42.0000 just like they did with the 2.08.0000 do the same... IT WOULD!
Hello,
I accidentally flashed a Test ROM w/ an MFG SPL (Leo_1_5_TMOUS_2.03.531.6_Radio_Signed_15.30.50.07U_2.06.50.23_3_Test) and meant to flash 2.13 shipped rom and now I am stuck with 2.02/2.03.0000 Engineering SPL and can't seem to flash any official/shipped roms to get back to 2.08/2.10 spl..
In other words how can I flash an SPL that is compatible with HSPL3 Utility..
(SPL 1.42.0000, SPL 1.62.0000, SPL 1.66.0000, SPL 2.07.0000, SPL 2.08.0000, SPL 2.10.000)
Please help!
Thanks.
Solution Found!
Lexx_xda said:
We have modified the installer HSPL3 Cotulla and added the ability to install HSPL 2.08 SPL 2.02. This version is not suitable for installation on SPL 2.07, on the other can.
On this ImaSoft me right, I give you a file and password for the archive.
Password: 96EF2E24-B657-4ebe-BB66-D2697FDEC815
Those wishing to thank ImaSoft:
WebMoney: Z392411566318; R371997483121; U774668296579
Click to expand...
Click to collapse
If this helped you out of SPL 2.02 please remember to thank these guys for working this out.
Info about MFG SPL:
Why can't I change the SPL with these test ROMs?
- These stock ROMs have an MFG SPL which cannot be overwritten in any way, not by flashing stock ROMs from SD, HSPL utility, SSPL or goldcard. The only successful way has been to drop the SPL with mtty (and has only been done once or twice).
- Good new is you can still use your HD2 and switch between 2.02 and 2.03 test ROMs..
What is an MFG SPL?
- MFG SPL = Engineering SPL
xmoo said:
Guys, MFG SPL allowes you to use some extra commands using JTAG which you wouldn't be able to use on normal SPL.
I remmeber back in the days there was this user "Leoni" who was stuck on 0.67MFG SPL.
Comonex helped him dropping it. I tried to contact him several times for you guys.
But he never responded back to me.
So spam pm him
Click to expand...
Click to collapse
Scabes24 said:
In other words how can I flash an SPL that is compatible with HSPL3 Utility
(SPL 1.42.0000, SPL 1.62.0000, SPL 1.66.0000, SPL 2.07.0000, SPL 2.08.0000, SPL 2.10.000)
Click to expand...
Click to collapse
this happened to several people some months ago.
goldcard may work, yes, but if not then sspl should get you flashing roms, but you can't change radio with sspl.
look for thread started by xmoo around february or march.
I thought I had tried sspl.. could I have done it wrong?
I found it here: http://forum.xda-developers.com/showthread.php?t=606713
I put the shipped 2.13 (also tried 2.05, 2.07, 2.09, 2.10, 2.11 stock and test roms) rom nbh from here: http://forum.xda-developers.com/showthread.php?t=655653 in a folder with the SSPL.exe and then run .exe but the progress bar stays at 0%
I also tried creating a goldcard, but not quite sure how it works. do I put an nbh on the card with it and boot from sd? or use CustomRUU?
The only ones I can flash back and forth are 2.02 and 2.03 test roms. I'm so annoyed!
Thanks
Nevermind the device wont even turn on anymore
2.02 is a MFG SPL.
Engeniering SPL. You have to drop it using mtty (but if you do it the wrong way, you may brick ur phone!)
Someone flashed 2.10.0 with sspl and sent it back for warrenty. When it came back it had 2.13 with SPL 2.10 on it....
xmoo said:
2.02 is a MFG SPL.
Engeniering SPL. You have to drop it using mtty (but if you do it the wrong way, you may brick ur phone!)
Someone flashed 2.10.0 with sspl and sent it back for warrenty. When it came back it had 2.13 with SPL 2.10 on it....
Click to expand...
Click to collapse
Well for some reason I tried flashing to the 1.01 test from the 1.03 to see if it would change from the MFG spl and I wasn't really paying attention to the progress bar but when I looked back it said (on PC) "ROM Update sucessful" but the phone didn't boot and won't even charge now?
What happened? and can I still send it in for warrenty?
Thanks for the help!
Scabes24 said:
Well for some reason I tried flashing to the 1.01 test from the 1.03 to see if it would change from the MFG spl and I wasn't really paying attention to the progress bar but when I looked back it said (on PC) "ROM Update sucessful" but the phone didn't boot and won't even charge now?
What happened? and can I still send it in for warrenty?
Thanks for the help!
Click to expand...
Click to collapse
Well if the phone isn't powering on, they probably can't check the spl...
So mayb yes. There are some other people who have done the same ish, and returned there phone. Ask them first.
xmoo said:
2.02 is a MFG SPL.
Engeniering SPL. You have to drop it using mtty (but if you do it the wrong way, you may brick ur phone!)
Click to expand...
Click to collapse
I am badly looknig for an MFG SPL.
Can someone point me where this is located pls? thanks!
Sry. please ignore my questions, I asked too fast...
Even MTTY does not remove the SPL 2.02.0000
Any solution for this yet? The test ROMs 201 to 209 are not intended for the TMOUS devices there for it is making it hard to remove the watermarked SPL.
I recontructed the ROM without the watermark but it will not install on the device. Anyone has an idea of how to remove the watermark? The SPL used form that ROM is the cause of the block...
Anymore thoughts on this issue?
I bought an eBay "for parts only" HD2 that the seller said sometimes booted into windows 6.5 but most of the time froze at the stick-together screen and never fully booted. Sounded maybe fixable to me, so I took a chance on it. I've never seen it try to boot into winmo 6.5 and when I check the bootloader info I see this:
PB81120 SS-B3
SPL-2.02.0000 XE
MicroP(LED) 0x05
MicroP(Touch) 0x50
The SPL-2.02.0000 was how I found this page. I've read many other pages about HSPL3 etc., but this phone is not recognized at all by two different WinXP machines w/ActiveSync. I don't get any messages regarding Qualcomm or anything like that. It's as if it isn't plugged in except the charge light does go on.
The only thing I can do is flash from the MicroSD card. But, haven't found any other ROMS other than the one that is on it already, that will actually flash. The others get stuck at a white screen that says Loading... and it just hangs there.
When the phone powers up it shows:
R 2.06.50.23......3 (the ...... is actually a squiggly looking line, not actually dots)
G 15.30.50.07u
D 2.03.75592 8G
then it just hangs there forever and goes into what looks like a screensaver mode (parts of the screen get darker and the stick together moves around as well).
If it's dead/bricked, what part inside would need replacing to get it running again (i.e. the motherboard)? This phone looks brand new. It's it fantastic condition. I've seen terrible looking HD2s on eBay that still work. So, I'm curious if there is something I could take out of an ugly phone and swap into this pristine HD2 and have it work.
As I see it, my only other options are to contact HTC and find out what they charge to repair it, or sell it for parts - again.
Since last post have discovered if I manually put phone into bootloader mode then plug it in via USB to my PC I hear the confirmation from the PC that the device is plugged in. Activesync does not fire up, but bootloader changes from serial mode to USB mode. I can start the ROM update utility, the black htc screen with 0% shows on the phone but eventually times out with an error [262] that the recovery process doesn't fix.
runningtiger said:
Since last post have discovered if I manually put phone into bootloader mode then plug it in via USB to my PC I hear the confirmation from the PC that the device is plugged in. Activesync does not fire up, but bootloader changes from serial mode to USB mode. I can start the ROM update utility, the black htc screen with 0% shows on the phone but eventually times out with an error [262] that the recovery process doesn't fix.
Click to expand...
Click to collapse
The person who owned that previously probably did the same thing I did and flashed one of the test roms with MFG SPL (2.02 or 2.03) Just don't try to flash 2.01, it'll most likely brick it. tomorrow the unbricking attempt on my device will begin.. but I guess you have to drop the SPL using mtty. talk to xmoo
I'll be very interested to read how your unbrick attempt turns out. I tried the MTTY instructions here: http://forum.xda-developers.com/showthread.php?t=668347
But, that post starts out saying "Before you start one note, this method only works if you succesfully flashed HSPL", which of course my HD2 does not have. Mine used to have 2.02.0000, but after many different tries at a fix - now has 2.00.1000. This is no better a situation to be in as it never gets past the "stick together" screen either.
I tried the create a goldcard.img info found here:
http://forum.xda-developers.com/showthread.php?t=591314
However, the directions for QMAT are outdated. But, I did download the new PSAS software offered at the site linked to in the above post and believe I got my 1GB MicroSD card's serial number but when I tried to "generate HTC goldcard" for Leo it gives a message that says "Goldcard for newer devices isn't implemented in this unregistered version" and it looks like it cost 30Euros to register. I'd pay if I knew for a fact this was going to work. But, I have my doubts because in step 2 you need to change the security permissions policies on the HD2. I have no access to the registry since there is no activesync connection possible at this point and I can't launch any programs like PHM.
The fix (if there is one even possible) has to come completely from the SD card as far as I can tell.
Good luck with yours! I hope something works and you come back here and post the sequence.
runningtiger said:
I'll be very interested to read how your unbrick attempt turns out. I tried the MTTY instructions here: http://forum.xda-developers.com/showthread.php?t=668347
But, that post starts out saying "Before you start one note, this method only works if you succesfully flashed HSPL", which of course my HD2 does not have. Mine used to have 2.02.0000, but after many different tries at a fix - now has 2.00.1000. This is no better a situation to be in as it never gets past the "stick together" screen either.
I tried the create a goldcard.img info found here:
http://forum.xda-developers.com/showthread.php?t=591314
However, the directions for QMAT are outdated. But, I did download the new PSAS software offered at the site linked to in the above post and believe I got my 1GB MicroSD card's serial number but when I tried to "generate HTC goldcard" for Leo it gives a message that says "Goldcard for newer devices isn't implemented in this unregistered version" and it looks like it cost 30Euros to register. I'd pay if I knew for a fact this was going to work. But, I have my doubts because in step 2 you need to change the security permissions policies on the HD2. I have no access to the registry since there is no activesync connection possible at this point and I can't launch any programs like PHM.
The fix (if there is one even possible) has to come completely from the SD card as far as I can tell.
Good luck with yours! I hope something works and you come back here and post the sequence.
Click to expand...
Click to collapse
2.03 has the mfg spl 2.02.0000 and i think 2.01 or 2.02 test ROMs have 2.00.1000. Least thats what I remember..
runningtiger said:
But, I have my doubts because in step 2 you need to change the security permissions policies on the HD2.
Click to expand...
Click to collapse
that part is only necessary to find the ID No. of the sd card. If you can get access to a working WM phone for a few minutes, you can use the other device to find the ID No.
There are alternate ways to get the ID, such as a linux boot disk on a laptop that has a built in SD card slot, but the slot must be directly mounted on the computers PCI bus, if it runs through a usb header it will give you the ID of teh USB header and not the card.
I'm trying to find a way for HSPL3.exe to disable the SPL version check.
This way you can directly flash other HSPL versions....
Thanks for looking into this..
xmoo said:
I'm trying to find a way for HSPL3.exe to disable the SPL version check.
This way you can directly flash other HSPL versions....
Click to expand...
Click to collapse
Is there anything I can do to help?
OK, please try to help me.
I'm having trouble in changing the SPL in my Leo.
I have installed WRONGLY SPL 2.08 instead of HSPL 2.08 by DFT HSPL3
Since this made me unable to install MAGLDR, i tried idiotic idea to install the newest stocking ROM from htc site (Serial confirmed) with htc installer from windows.
Right now, i have working HTC with details as below:
ROM: 3.14.479.2 (04666) WWE
RADIO: 2.15.50.14
SN: HT03DNW00564
When i get into bootloader, there is:
PB81100 HX-BC
SPL-2.08.0000 8G XE
MicroP(LED) 0x05
MicroP(TOUCH) 0x40
So, time for the problem:
Right now, i can't load anything to my device. When i put LEOIMG onto SDCard, device freezes on white screen with "Loading". I have tried stock roms: 1.48.479.1; 3.14.479.2(same as installed); 1.48.405.2
When i try to load another SPL (or HSPL) from DFT HSPL4 device reboots, goes to bootloader and nothing happens. DFT HSPL just shows progres bar moving and nothing happens (i have waited 20 mins).
I have no more ideas anymore, what can i do. Hopefully Phone works, and those not have any Cooked ROM on it, but i don't wont to use this ROM
PLEASE, try to help...
PS. I have tried different USB Ports, i have installed fresh Windows (really). I'm using XP SP3. Battery is at 100%.
Try running a task 29 and then run the HSPL again and install the 2.08 HSPL. Then flash MAGLDR then the ROM you want.
Edit: Sorry I momentarly forgot you have to have HSPL to do a task 29. Do this make sure your phone is in bootloader and plug it into the computer via USB cable and then wait until it says USB at yhe bottom in the white. Then and only then run the DFT HSPL again.
With Task29 also nothing happens. Same as with ROMS and HSPL, After synchro in ActiveSync, i have run TASK29, then my Leo goes into Bootloader and nothing happend. On Windows screen i have 0% progress bar, on HTC HD2 i see bootloader with USB status.
ERROR 302
EDIT: After clicking through recovery steps, Leo turned to showing Progres bar, but also stops at 0%.
RealWaaagh said:
Right now, i can't load anything to my device. When i put LEOIMG onto SDCard, device freezes on white screen with "Loading". I have tried stock roms: 1.48.479.1; 3.14.479.2(same as installed); 1.48.479.1
Click to expand...
Click to collapse
Just making sure: did you try to flash those stock roms over USB? Stock SPL's don't have the same protection that HSPL has, and can be overwritten by flashing over USB just fine.
Also: until you're sure you can reflash at least something, it might be better to stay away from task29
I tried also by USB (all three), and still the same. Progress bar on PC and Phone shows 0% and after some time, Installer shows ERROR about connection. ERROR302 i think.
PS. I really start to think i'm missing some detail. ROM works, everything works excluding boot loader. For me, it looks like bootloader is broken somehow, and i don't have idea how to make it work properly.
RealWaaagh said:
I tried also by USB (all three), and still the same. Progress bar on PC and Phone shows 0% and after some time, Installer shows ERROR about connection. ERROR302 i think.
PS. I really start to think i'm missing some detail. ROM works, everything works excluding boot loader. For me, it looks like bootloader is broken somehow, and i don't have idea how to make it work properly.
Click to expand...
Click to collapse
Hmm... If you can't get your phone to flash anything over either USB or SD, it does sound like your bootloader might be corrupted or something. That 302 error also doesn't sound good.
I guess if you have them you could try flashing using:
- a different pc/laptop
- a different SD card (perhaps a goldcard?)
*Probably* won't help, but won't make things worse either.
Ok, for today i have enough. I will try tomorrow with another PC.
SD Cards i already tried three of them.
RealWaaagh said:
OK, please try to help me.
I'm having trouble in changing the SPL in my Leo.
I have installed WRONGLY SPL 2.08 instead of HSPL 2.08 by DFT HSPL3
Since this made me unable to install MAGLDR, i tried idiotic idea to install the newest stocking ROM from htc site (Serial confirmed) with htc installer from windows.
Right now, i have working HTC with details as below:
ROM: 3.14.479.2 (04666) WWE
RADIO: 2.15.50.14
SN: HT03DNW00564
When i get into bootloader, there is:
PB81100 HX-BC
SPL-2.08.0000 8G XE
MicroP(LED) 0x05
MicroP(TOUCH) 0x40
So, time for the problem:
Right now, i can't load anything to my device. When i put LEOIMG onto SDCard, device freezes on white screen with "Loading". I have tried stock roms: 1.48.479.1; 3.14.479.2(same as installed); 1.48.405.2
When i try to load another SPL (or HSPL) from DFT HSPL4 device reboots, goes to bootloader and nothing happens. DFT HSPL just shows progres bar moving and nothing happens (i have waited 20 mins).
I have no more ideas anymore, what can i do. Hopefully Phone works, and those not have any Cooked ROM on it, but i don't wont to use this ROM
PLEASE, try to help...
PS. I have tried different USB Ports, i have installed fresh Windows (really). I'm using XP SP3. Battery is at 100%.
Click to expand...
Click to collapse
Mate, you said that you flashed stock rom v.3.14.xxx but you also said that the SPL 2.08.
I m quite confused, usually the stock rom v.3.14 contains SPL 3.03 (not 2.08). So, I m curious what version of your hd2, is it TMOUS?
Have you tried a HARD RESET?
Try HR and see whether your hd2 can pass that.
If succeded, you can retry flashing HSPL over usb (dont forget to turn off antivirus, firewall, internet on your pc) or else retry flashing via micro sd flashing (use 2,4 or 8 gb reformated micro sd)
hope you can succeed.
good luck
When i try to load another SPL (or HSPL) from DFT HSPL4 device reboots, goes to bootloader and nothing happens.
Click to expand...
Click to collapse
forget starting with the phone already running, it doesnt need to connect to activesync, that just adds a load of confusion, saying that in all the instructuons.
phone off
phone into bootloader
usb
hspl4
choose 2.08.hspl
bootloader
flash rom
I have tried stock roms: 1.48.479.1; 3.14.479.2(same as installed); 1.48.405.2
Click to expand...
Click to collapse
so thats two east europe and a wwe rom, , you dont have hspl installed, , and you're unsure why nothing will flash?
cancel this post
RealWaaagh said:
Ok, for today i have enough. I will try tomorrow with another PC.
SD Cards i already tried three of them.
Click to expand...
Click to collapse
One more question are you right clicking and running HSPL as administrator???
samsamuel said:
forget starting with the phone already running, it doesnt need to connect to activesync, that just adds a load of confusion, saying that in all the instructuons.
phone off
phone into bootloader
usb
hspl4
choose 2.08.hspl
bootloader
flash rom
so thats two east europe and a wwe rom, , you dont have hspl installed, , and you're unsure why nothing will flash?
Click to expand...
Click to collapse
I have already tried to start hspl4 without running WinMo, same effect. In WinXP Bootloader still displays on the Phone, and in DFT HSPL progres bar just bounce from left to right.
In Vista DFT HSPL returns critical error about connection.
About ROMS, 3.14 is East Europe (downloaded from HTC after checking serial) and 1.48 is WWE, also checked with serial from HTC site.
I have tried 1.48 EE since somewhere i have read, taht i have to get rom with the same number on the end, as installed (ie. 3.14.479."2")
PS. I can't tconnect to Mobile Center is Vista. With ActiveSync on WinXP there are no problems.
silverwind said:
Mate, you said that you flashed stock rom v.3.14.xxx but you also said that the SPL 2.08.
I m quite confused, usually the stock rom v.3.14 contains SPL 3.03 (not 2.08). So, I m curious what version of your hd2, is it TMOUS?
Have you tried a HARD RESET?
Try HR and see whether your hd2 can pass that.
If succeded, you can retry flashing HSPL over usb (dont forget to turn off antivirus, firewall, internet on your pc) or else retry flashing via micro sd flashing (use 2,4 or 8 gb reformated micro sd)
hope you can succeed.
good luck
Click to expand...
Click to collapse
My Phone is East Europe WWE (afaik).
I have installed SPL 2.08 onto HSPL 1.6 with DFT HSPL3.
Then i have installed 3.14 by USB. I don't know, why i still have SPL2.08 if you say i should't.
HR works fine.
In a minute i will check HSPL with internet turned off.
How to flash HSPL via microSD ?
Since i can't flash whole ROMs (maybe i have wrong ones, but they pass serial check on htc.com) from microSD (3 cards checked 2GB SD, 4 GB SDHC(don't work), 16 GB SDHC)
T-Macgnolia said:
One more question are you right clicking and running HSPL as administrator???
Click to expand...
Click to collapse
When i try run in Vista, i click and run it as Admin, but in XP i have Admin Account, so i just run it.
PS. Sorry for three posts, i didn't see multiple-quote option
RealWaaagh said:
When i try run in Vista, i click and run it as Admin, but in XP i have Admin Account, so i just run it.
PS. Sorry for three posts, i didn't see multiple-quote option
Click to expand...
Click to collapse
Doesn't matter, still right click and run as admin, always put phone in bootloader yourself before starting to flash, if it fails just run hspl.exe again. Try all USB ports.
No, you can't apply hspl from SD card.
samsamuel said:
Doesn't matter, still right click and run as admin, always put phone in bootloader yourself before starting to flash, if it fails just run hspl.exe again. Try all USB ports.
No, you can't apply hspl from SD card.
Click to expand...
Click to collapse
PROBLEM SOLVED
I needed to make another admin account in WinXP. And then use it by Run As (then choose this new account).
I don't know why it works like that, but it worked.
Just to give all informations.
After more testing, i detected my Computer problem. My USB ports were not working properly, and update of Motherboard BIOS helped (ASUS P7P55D). So, i don't know what was the exact issue of problems.
Hello,
there are a lot of similar topic but none of them answered my question.
General situation looks like this:
after flashing with MAGLDR device is stuck on htc splash screen and doesn't respond to any button
What was already done:
- initially, device had factory 3.14.x WWE ROM with 2.15.50.14 radio. SPL was changed with DFT tool to HSPL 2.08, MAGLDR was flashed with no problems (tried it few times)
Since that didn't worked, this is what I did:
- I recall reading that if someone has 3.14.x ROM then he/she must downgrade to ROM with 1.66.x or 1.72.xx. So I did that with factory ROM, (what struct me is that the SPL wasn't changed), flashed 2.15.50.14 radio, tried MAGLDR 1.13 once again. That didn't work
- since, SPL wasn't changed with official ROM I thought this is the issue here, so I've change it to SPL 3.03 back again and flashed 1.66.x official ROM. Flash procedure did change to SPL 1.42. I changed it to 2.08HSPL with DMT tool once again, 2.15.50.14 radio was flashed, then MAGLDR. It also gets stuck on splash screen.
- Next I've read that something called Task29 will probably fix my issue. So.. I've flashed with original 3.14.x ROM and then went with the process once again but I've run Task29 tool between changing SPL to HSPL 2.08 and flashing MAGLDR. That didn't work either
Additional observations:
- I've changed HSPL 2.08 to SPL 2.08, after that running any flash procedure (MAGLDR or official ROM), will effect with 0% progress
- changing to SPL 3.03 will cure above (at least for official ROM)
- in RUU tool the previous version is never seen (on the screen when you confirm update)
Every procedure was done according to newbie guides available on this forum, I've experience with flashing other OS on couple of HD2 devices, but that is the first one that gives me a hard time.
Any suggestion what I should do next?
forget about continually flashing various stock roms, its not necessary.
forget what's gone before, do this and report back.
Phone into bootloader
connect usb, When 'serial' becomes 'usb' continue.
run hspl4 and choose 2.08.hspl
when it completes go immediately back into bootloader
flash magldr
straight back into bootloader
flash radio 2.15.50
let the phone restart.
report back.
pydzik said:
Hello,
there are a lot of similar topic but none of them answered my question.
General situation looks like this:
after flashing with MAGLDR device is stuck on htc splash screen and doesn't respond to any button
What was already done:
- initially, device had factory 3.14.x WWE ROM with 2.15.50.14 radio. SPL was changed with DFT tool to HSPL 2.08, MAGLDR was flashed with no problems (tried it few times)
Since that didn't worked, this is what I did:
- I recall reading that if someone has 3.14.x ROM then he/she must downgrade to ROM with 1.66.x or 1.72.xx. So I did that with factory ROM, (what struct me is that the SPL wasn't changed), flashed 2.15.50.14 radio, tried MAGLDR 1.13 once again. That didn't work
- since, SPL wasn't changed with official ROM I thought this is the issue here, so I've change it to SPL 3.03 back again and flashed 1.66.x official ROM. Flash procedure did change to SPL 1.42. I changed it to 2.08HSPL with DMT tool once again, 2.15.50.14 radio was flashed, then MAGLDR. It also gets stuck on splash screen.
- Next I've read that something called Task29 will probably fix my issue. So.. I've flashed with original 3.14.x ROM and then went with the process once again but I've run Task29 tool between changing SPL to HSPL 2.08 and flashing MAGLDR. That didn't work either
Additional observations:
- I've changed HSPL 2.08 to SPL 2.08, after that running any flash procedure (MAGLDR or official ROM), will effect with 0% progress
- changing to SPL 3.03 will cure above (at least for official ROM)
- in RUU tool the previous version is never seen (on the screen when you confirm update)
Every procedure was done according to newbie guides available on this forum, I've experience with flashing other OS on couple of HD2 devices, but that is the first one that gives me a hard time.
Any suggestion what I should do next?
Click to expand...
Click to collapse
if what the friend above suggested doesnt work, then give us the details about your device. i have a Tmous and im in Europe and went through hell until i got it right...if you do it then flashing the rom you want is a piece of cake!
samsamuel said:
Phone into bootloader
connect usb, When 'serial' becomes 'usb' continue.
run hspl4 and choose 2.08.hspl
when it completes go immediately back into bootloader
flash magldr
straight back into bootloader
flash radio 2.15.50
let the phone restart.
report back.
Click to expand...
Click to collapse
Did that, phone had initially SPL 1.42 and 1.66.x ROM. I didn't let him boot between steps, just went to bootloader each time... and I'm still stuck at splash screen with no response to any key.
sofialoca said:
if what the friend above suggested doesnt work, then give us the details about your device. i have a Tmous and im in Europe and went through hell until i got it right...if you do it then flashing the rom you want is a piece of cake!
Click to expand...
Click to collapse
What details would you like to know?
pydzik said:
stuck at splash screen with no response to any key.
Click to expand...
Click to collapse
that behavour is expected when either spl ISN'T 2.08.hspl and/or radio isn't correct. The only other reason for magldr not showing up must be a faulty device.
Well... I can flash it with every HTC official ROM, and it works, calls can be made, wifi works fine, no spontaneous reboots or freezes...
Made two other observations:
1. On the device that is stuck on splash screen there is an additional bar in boot loader saying "Security unlocked", just like in this thread: http://forum.xda-developers.com/showthread.php?t=1501745
2. I've started to look at different boot loader screens across the net, and it seems that majority of them has HX-BC (mine has different) version after the board PB81100 name. I've also compared bootloader screen after changing SPL to HSPL 2.08 on two different devices. The values before and after CotullaHSPL were different.
What should I do now? Searching for a method to remove that "Security unlocked" string or give up since the version of my board won't be able to run MAGLDR?
My device is not TMOUS, it is 512MB device.
Edit: after some research I think that my device has NAND-Flash ROM from Samsung not Hynix, so different flash algorithm should be used. I'm now going for a low-level research. If that is the case, than I think MAGLDR needs version 1.14 ... will report later.