Hello,
I didn't have any USB connexions anymore on my 32a magic.
In fastboot, no problems.
But with any rom (myhero, GyD, Cyanogen), no USB available !
I don't have the USB mount notification on magic, and have an "unknown usb device" notification on xp.
But the Sd card is ok.
How can I fix it ?
Thanks
Nobody ?
Many Hero owners have this trouble
I checked PID and VID. Both are 0x0000 ! (unknown device)
It sounds like an hardware trouble, but why is it ok in fastboot mode ?
I have exactly the same problem on my 32B... since I bought the phone(second hand), that it has this problem, I have been looking everywhere and I got no answer...
I read somewhere that flashing the SPL could solve the problem, but I haven't tried it.
I flashed to SPL 2010 yesterday... no improvements.
mika91 said:
I flashed to SPL 2010 yesterday... no improvements.
Click to expand...
Click to collapse
Humm, thats bad news
I have the same problem on my MT3G after the motherboard on my gaming rig blew, the phone just went dark and it also destroyed my usb jump drive that was plugged in next to it. It (usb jump drive) was really hot to the touch when I pulled it out. I smelled something burning from inside the computer, I never did figure out what it was. Now when I plug the phone into my loptop all the phone does is charge, the computer wont see it and neither does the phone ask to mount. The sd card is still good but now I either have to use a card reader or transfer files through bluetooth.
I wiped, formatted, "mount usb" through the recovery, flashed different roms, nothing works. I guess I damaged the circuit board or the usb port somehow. I wanna call Tmo for a warrenty replacement but then Ill have to flash back to the original spl and ROM. I dont really want to go through the rooting process again. Is there a way to find out for sure if it is the software or a hardware issue? Like some kind of test through the terminal?
phatmanxxl said:
I have the same problem on my MT3G after the motherboard on my gaming rig blew, the phone just went dark and it also destroyed my usb jump drive that was plugged in next to it. It (usb jump drive) was really hot to the touch when I pulled it out. I smelled something burning from inside the computer, I never did figure out what it was. Now when I plug the phone into my loptop all the phone does is charge, the computer wont see it and neither does the phone ask to mount. The sd card is still good but now I either have to use a card reader or transfer files through bluetooth.
I wiped, formatted, "mount usb" through the recovery, flashed different roms, nothing works. I guess I damaged the circuit board or the usb port somehow. I wanna call Tmo for a warrenty replacement but then Ill have to flash back to the original spl and ROM. I dont really want to go through the rooting process again. Is there a way to find out for sure if it is the software or a hardware issue? Like some kind of test through the terminal?
Click to expand...
Click to collapse
Humm, that means that we might have something "fried" on our phones
The weird thing is that I can access usb through fastboot... Are you able to use fastboot on your phone?
It really would be interesting if there was any way to check if it really is an hardware problem or software problem.
Has anyone else got a clue on this one?
If we can access USB in fastboot, it sounds like a software problem to me.
But after trying several roms and spl, no changes.
I would try to flash a new SPL, but if I do that I won't be able to put back the original SPL and may not take it back to HTC and repair it under warranty... I will wait about a week or so, put back as it was originally, and send it back to HTC and see if they will repair it.
Game Over for me !
I tried some SPL, but now my sapphire is bricked !
:'(
mika91 said:
Game Over for me !
I tried some SPL, but now my sapphire is bricked !
:'(
Click to expand...
Click to collapse
That's weird, what spl have you used and what was your initial spl? How did you flashed that SPL?
I tested all SPL I think !
But the last i tried sould be 1.33.2004.
Now, phone locked on TIM logo screen, impossible to go into fastboot or recovery, even with unbrick hacks found on the forum
If it gets to the operate logo, I guess that you should be able to get to recovery rom...
Can't you get to hboot mode(volume down + power on) , or to fastboot mode(back + power on)?
Nop !
I tried all combinations: Volume Down + power on, Back + power on, Home + power on.
Same result! Operator Logo
Related
All started with trying to upgrade(rewrite) the GSM part because the Hermes had problems with phone part - when trying to call - the phone stop responding, bus the pda part sill worked.
So - I tried and tried and tried again, reading many threads about HARD SPL,Flashing radio, etc. Nothing worked..
In the end "i managed" to kill GSM - phone had "No Gsm" on boot-up.
From there i tried to downgrade SPL to 1.04 so that i try to "raw" rewrite the GSM part.
But something went terribly wrong, and while downgrading SPL, the phone suddently shutdown and never opened again.
Now i have the folowing situation: NO BOOTLOADER, no usb conectivity, nothing
This means that i cannot connect via USB whatever i try.
Is there any hope for me? or is it TOTALLY BRICKED?
Any help is apreciated!! I can even dismantle the mobile if there is any way to flash it via some kind of jtag connection...anything ...
The folks at www.imei-check.com can do the JTAG flashing. Just email them. It would be costly for you to do it yourself...
Are you saying that the phone won't turn on at all or that it does but you can't get a bootloader screen?
Have you tried taking the battery out for a while? Have you tried flashing an OEM rom and radio compatible with your device off an SD card?
All of this info is in the wiki, as are OEM roms you can flash.
Let us know how you get on.
Good luck.
WB
Try this:
1.) Remove battery
2.) Connect Hermes to charger or USB
3.) Insert the battery while Hermes is connected to charger
4.) Red light should turn Amber
5.) Soft Reset
@wacky.banana: The phone is totaly dead: no bootloader, doesn't boot at all, doesn't seem to have any USB conectivity at all. Flashing from micro sd doesn't work : probably because the bootloader isn't working.
@drummer10630: i'll check with imei-chek about jtag flashing, especially the price and shiping costs.thanks
@markafreeman: I tried, but when i put the battery in, the red light goes off, not to amber . no soft or hard reset helps. not even leaving the battery out for 2 weeks - i had tried that too . thanks anyway.
Anything else I can try? - phone totaly dead, no bootloder, no usb conectivity - cannot use mtty, cannot flash from microsd
I had to get a replacement device at that point when it happened to me.
Maybe someone else know a way to get it working.
Good luck.
get onto orange
tell them you dropped the phone
and it crashed and wouldnt turn on
so you managed to hard reset it
and it crashed an ****ed up
they'll replace it
well they will send it to HTC
who just replace the handset rather than repair it
Hi dancameo2k , maybe you will not remember but plz:
I ve bought recenty an spv m3100, im effortless trying to flash the rom to an wm6 version.
Like you ive started with the hardsppl flash thing to prevent bricking it and prior to sd flashing... and im not sure if its workin...
plz can you explain in detail how did you bricked it??? thx!!!!
the rom you used to flash was an american version or european one???
Hi,
if i connect my HTC Touch HD with my computer, it's just charging, nothing more. If i go to Bootloader, there is just written Serial even if its connected.
I am using Dutty ROM since some weeks and didn't had any problems till a few days ago, the strange thing is, that i didn't change anything.
I tried it on my laptop and on my computer the one with windows vista the other one with win xp, it worked on both, but not anymoe.
i also have a problem with the camera, if i press it nothing happens it just stays in the menu. Some days ago i got a error failed to initialize camera, but no more error anymore.
In my opinion my hardware is broken somehow, i hope someone in here can tell me sth different and a solution.
And if my hardware is broken, how can flash my original rom back without an usb connection, because the warenty will be gone with a custom rom i think.
I hope someone can help me.
Kryston said:
Hi,
if i connect my HTC Touch HD with my computer, it's just charging, nothing more. If i go to Bootloader, there is just written Serial even if its connected.
I am using Dutty ROM since some weeks and didn't had any problems till a few days ago, the strange thing is, that i didn't change anything.
I tried it on my laptop and on my computer the one with windows vista the other one with win xp, it worked on both, but not anymoe.
i also have a problem with the camera, if i press it nothing happens it just stays in the menu. Some days ago i got a error failed to initialize camera, but no more error anymore.
In my opinion my hardware is broken somehow, i hope someone in here can tell me sth different and a solution.
And if my hardware is broken, how can flash my original rom back without an usb connection, because the warenty will be gone with a custom rom i think.
I hope someone can help me.
Click to expand...
Click to collapse
A hard reset will quickly tell you if it's hardware or software and you don't need usb for that. There is also an option which dictates what the phone does when connected via usb, so you might want to check that option first.
need to read & search a little more
last paragraph of this post outlines how to return to stock rom
http://forum.xda-developers.com/showpost.php?p=2710548&postcount=1
i did hardreset, but still same problem
what i also noticed, is that sometimes my display don't work, i have sound and vibrate feedback, but i see just a black display, softreset etc doesen't work somehow i have to take of the battery.
i noticed also that the usb cable is a bit broken, but it still charges the phone.
but i already saw that normal usb cable should work too, so i tried it but no change.
i guess i will try to get the stock rom again now and see what happens
well like i thought, i can't get the stock rom, because i dont have a usb connection
any more suggestions?
Kryston said:
well like i thought, i can't get the stock rom, because i dont have a usb connection
any more suggestions?
Click to expand...
Click to collapse
There is 2 methods to flashing roms. Have you tried SD card method?
1. Download ROM image you would like to use, normally named RUU_Signed.nbh, and rename it to "BLACIMG.nbh"
2. Copy BLACIMG.NBH into the root dir of your Storage Card.
3. Be sure to have at least 30% of charge.
4. Turn off your device by using the Power Button
5. Go to bootloader mode. Push and hold Vol Down + press Power button.
6. As soon as presented the message, push Power button to start flashing or Volume Down button to cancel.
7. The whole procedure will take about 3 minutes. After you finish and see the relative message, soft reset your device, you are ready.
thanks god i didn't bring the phone to shop yet xD
thank u, i will check this method i will post here if it works later
well now i have another problem
there is written upgrade rom code error please try again on bootloader, i cant turn it on anymore it gets stuck on the loading screen of the flashing progress
Kryston said:
well now i have another problem
there is written upgrade rom code error please try again on bootloader, i cant turn it on anymore it gets stuck on the loading screen of the flashing progress
Click to expand...
Click to collapse
I had this exact same problem a while back after a bad flash. What you need to do is flash carriers orginal stock rom onto device. This will be the only rom which will work. Go to wiki section on stock roms here and download your original rom and flash it. Don't worry if bottom of bootloader is blank or doesn't say 'usb', original rom will flash anyhow.
More info read this thread
i am downloading right now, hopefully it will work, i will write more infos later
thank u for your help, without you, i would be lost...
i am stuck, i get error 206 connection
i downloaded stock rom to my pc
and i'm a bit confused, my pc noticed that i pluged in the phone, my device manager showed my phone, this worked only one time, now nothing...
EDIT: in bootloader mode, serial staus doesnt switch to usb or blank, updateing usb driver doesn't work without usb connection to device, at least i didnt found sth here
i will try it on my other computer now, but i doubt it will work
EDIT2: got usb connection for some seconds, problem is my hardware of device its broken somehow, if i press on th eback of the device i am able to get usb connection, now it failed, i will give it some more tries, there was sth 294 ID error
EDIT3: seems like its the wrong rom, how can i find out which rom will work?
EDIT4: semms like i got a working rom its at 10%
EDIT5: Device working again, usb working perfectly again, dunno why, but camera still doesnt work, there happens nothing if i press on it and display turns black sometimes as before.
i flashed an O2 Rom now, from my provider.
My last question now is, what about warranty, how can i know that uspl/hsapl is fully removed from device and how to find out if device is now a case of warrnty, where can i check it? because i want a working camera again, so i think i need the warranty
Some infos:
O2 Provider ROM flashed
On Bootloader i see:
BLAC100 32M
SPL-1.54.0000
MicroP-Blackstone (LED) v6
In my opinion its fine for warranty, but i want someone to confirm this.
And thank you alot for ur help and work in this forum =)
If you have an official HTC upgrade rom on your device you are fine for warranty. As your SPL says 1.54.0000 this means you haven't got USPL or HSPL on your device, so you're fine.
thank you very much
Hello fellow HD2 users,
I've got an HD2 T-Mobile UK. I've just tried my luck with HSPL, I've succeessfully installed HSPL using the steps in this thread: http://forum.xda-developers.com/showthread.php?t=609477
However, when I copied the LEOIMG.nbh (1.48 offiicial rom) file to the micro SD 8GB card; and rebooted, things seemed ok untill it suddenly stopped the progress of flashing the ROM and gave me a Grey screen with the Error 00028002 "not Allow" sort of thing.
So I tried yanking battery out, rebooting normally, it displays a grey triangle with " ! " in the middle and then displays the 00028002 error then back to Tri colour bootloader, I noticed that the HSPL is gone and its back now to 1.42.0000
I even tried a Factory reset, it does the reset I reboot, but it still shows me grey triangle and same routine. I've tried everything now. This bloody T-mobile phone is just useless to me at the moment !
Can you please HELP !!! Thank you so much !
Regards !!
Ok found solution, I just had to install the official T-mobile 1.43.110.0 ROM from this link:
http://rapidshare.com/users/258XUJ
After just switching on the phone with microsd inside, I just plugged the usb and started the RUU and followed the steps and things are back to square one now.
not thrilled that it has been a nightmare so far to get a new rom on.
but at least I can use my phone with its basic functionalities. not gona push my luck again...
You cannot flash official ROMS from the sd because it replaces the SPL with a stock one. Presume it got half way through then decided the ROM was not for your device since it hasd replaced the SPL. Cooked ROMS are ok to flash from SD but for Stock use the RUU.
tell me it's working please.my HD2 from UK T-Mob is same "bricked" and in Slovakia is very very difficult to find somebody who can fix this....i think maybe only the HTC repair center
^
If your phone can load up into the boot loader (tri-color screen) your phone is not bricked.
Deeper Trouble:Same error,but cannot use USB!!!
Guys,
im in even much deeper **** now.I accidentally tried flashing a stock ROM via SD card and now ive gt the same ROM code error.What makes this worse is that my Vista computer is not recognizing any USB connection when i connect my HD2 to the computer.If i need to flash a stock rom via RUU wrapper to get through this stupid ROM code error, i need a USB connection at the first place...which IS NOT WORKING NOW!!!...im sitting duck here guys...i really really need your help on this one.im extremely frustrated and helpless.thanks alot...
When u say USB not working, how do you know?
Put phone in bootloader, connect USB cable,,, on phone does "serial" become "USB"? If yes then just run the flash.
samsamuel said:
When u say USB not working, how do you know?
Put phone in bootloader, connect USB cable,,, on phone does "serial" become "USB"? If yes then just run the flash.
Click to expand...
Click to collapse
Go to this thread Sam as kawshigan started a new thread
semo2010 said:
Ok found solution, I just had to install the official T-mobile 1.43.110.0 ROM from this link:
http://rapidshare.com/users/258XUJ
After just switching on the phone with microsd inside, I just plugged the usb and started the RUU and followed the steps and things are back to square one now.
not thrilled that it has been a nightmare so far to get a new rom on.
but at least I can use my phone with its basic functionalities. not gona push my luck again...
Click to expand...
Click to collapse
broken link
how can i revive my dead T-MOBILE HD2?...
it has no power & bootloader; only continuous vibration after pressing the power button...
donkeanu said:
how can i revive my dead T-MOBILE HD2?...
it has no power & bootloader; only continuous vibration after pressing the power button...
Click to expand...
Click to collapse
What did you do right before it was dead?
Did you change the Radio?
Might be battery related too.
Try to find someone else with an HD2 and swap the battery to try.
help
same here. i accidentaly flashed a diff radio rom
it just contiunsly vibrates
no light, no power,... please help me in reviving this .
thanks,
sugui said:
same here. i accidentaly flashed a diff radio rom
it just contiunsly vibrates
no light, no power,... please help me in reviving this .
thanks,
Click to expand...
Click to collapse
You cant, you've bricked it. Only way is to JTAG or replace board as far as I know.
sugui said:
same here. i accidentaly flashed a diff radio rom
it just contiunsly vibrates
no light, no power,... please help me in reviving this .
thanks,
Click to expand...
Click to collapse
If you have flashed a EU/Asian Radio/stock ROM on a T-Mous device, than it's broken.
kurt-willems said:
What did you do right before it was dead?
Did you change the Radio?
Click to expand...
Click to collapse
I can still enter botloader flash hspl but can do nothing the phone just turns off
can anyone help me! when i connect and try to flash another rom it turns off at 29% ! Has anyone been able to solve this problem! it is a brand new phone i bricked the same day i bought it trying to put the energy rom! i dont live in the usa so i paid a hard 500 bucks to get this phone all for nothing
Don-Maco said:
I can still enter botloader flash hspl but can do nothing the phone just turns off
can anyone help me! when i connect and try to flash another rom it turns off at 29% ! Has anyone been able to solve this problem! it is a brand new phone i bricked the same day i bought it trying to put the energy rom! i dont live in the usa so i paid a hard 500 bucks to get this phone all for nothing
Click to expand...
Click to collapse
If you can get it into bootloader than it is not bricked. It sort of sounds like you might have a dead battery. Try to let it charge are maybe get an external charger for it.
Now as for your problem with installing a ROM you can flash either by USB and computer or via SD card. If you use the USB and computer method then out your phone into bootloader and connect it to the computer via USB cable and wait for Serial in the white bar of the bootloader screen to change to USB and then flash the ROM.
If you want to use the SD card method put your SD card into a micro SD card reader and plug it into your computer. If the ROM you downloaded is a .exe then change it to .zip and then right click and select viewl or explore wich ever one it shows. Find the .nbh file and rename it to leoimg.nbh and copy it to the SD card and insert the SD card into your phone. Put your phone into bootloader but hold the volume down button down until you see searching on your phone screen then release the volume down button. The ROM will then flash.
T-Macgnolia said:
If you can get it into bootloader than it is not bricked. It sort of sounds like you might have a dead battery. Try to let it charge are maybe get an external charger for it.
Now as for your problem with installing a ROM you can flash either by USB and computer or via SD card. If you use the USB and computer method then out your phone into bootloader and connect it to the computer via USB cable and wait for Serial in the white bar of the bootloader screen to change to USB and then flash the ROM.
If you want to use the SD card method put your SD card into a micro SD card reader and plug it into your computer. If the ROM you downloaded is a .exe then change it to .zip and then right click and select viewl or explore wich ever one it shows. Find the .nbh file and rename it to leoimg.nbh and copy it to the SD card and insert the SD card into your phone. Put your phone into bootloader but hold the volume down button down until you see searching on your phone screen then release the volume down button. The ROM will then flash.
Click to expand...
Click to collapse
Thats the problem my battery works in another phone but my phone just not stay on! it stays long enough to flash catula & beepe hspl and back to spl! if i try flashing a radio is it flashes it then says its not supported on this rom after 100% if its not supported why install after 100% i got the radio on the t-mobile forum! so its good! When i used anothe battery that is charged to 100% the phone just wouldn't turn on! i even ordered a new battery and data cable yesterday brand new & will have to wait a crazy two weeks shipping! I ant see what went wrong cuz i have been flashing Htc & windows mobile devices like for ever! just this usa version wich is supposed to be high end is giving me the creeps! what can i do
Don-Maco said:
Thats the problem my battery works in another phone but my phone just not stay on! it stays long enough to flash catula & beepe hspl and back to spl! if i try flashing a radio is it flashes it then says its not supported on this rom after 100% if its not supported why install after 100% i got the radio on the t-mobile forum! so its good! When i used anothe battery that is charged to 100% the phone just wouldn't turn on! i even ordered a new battery and data cable yesterday brand new & will have to wait a crazy two weeks shipping! I ant see what went wrong cuz i have been flashing Htc & windows mobile devices like for ever! just this usa version wich is supposed to be high end is giving me the creeps! what can i do
Click to expand...
Click to collapse
note i cant flash the rom cuz it hangs at 29% then nothing happens for like 10 minutes! then the phone turns itself off! and it just wouldn't budge! i never flashed through sd card so i really would like the exact steps to avoid errors! i dont wanna screw 500u$d
Don-Maco said:
Thats the problem my battery works in another phone but my phone just not stay on! it stays long enough to flash catula & beepe hspl and back to spl! if i try flashing a radio is it flashes it then says its not supported on this rom after 100% if its not supported why install after 100% i got the radio on the t-mobile forum! so its good! When i used anothe battery that is charged to 100% the phone just wouldn't turn on! i even ordered a new battery and data cable yesterday brand new & will have to wait a crazy two weeks shipping! I ant see what went wrong cuz i have been flashing Htc & windows mobile devices like for ever! just this usa version wich is supposed to be high end is giving me the creeps! what can i do
Click to expand...
Click to collapse
Check your battery pins in your HD2 to make sure that one or more of them are not slightly bend more than it should be. If none don't appear to be bend if possible compare them to another HD2 to make sure the are in the proper positions. If they are then you might have an internal hardware problem. But don't just take my word for thag cause I am no expert when it
comes to the hardware side of the HD2.
Edit: I just read your other post here is a link to the thread on flashing via SD card. Read the first post for detailed instructions on flashing via SD card
heey thanks man i'll try that as soon as i get from work and see if that helps!
T-Macgnolia said:
Check your battery pins in your HD2 to make sure that one or more of them are not slightly bend more than it should be. If none don't appear to be bend if possible compare them to another HD2 to make sure the are in the proper positions.
Click to expand...
Click to collapse
Thanks for that tip, it solved my problem: the middle pin wasn't in proper position.
It appears that my HD2 is having some problems with its USB-Port since a connection will only be established if the USB-cable is held in a weird angle.
My Phone has been kept very carefully and is otherwise in great condition.
I think this may be a problem with the usb-port inside and it still has warranty here in germany.
The problem is that i used Magldr to install Android through clockwork mod, is there a way to get back to Windows Mobile without using a usb cable?
Since i hardly think i could send it in with Android installed.
Chances are it is the port on your phone....They seem pretty prone to this problem after a while.......Im assuming you've tried a different cable/usb port right??
Good news is that yes, you can get back to WM without USB pretty easily.
You need to download the correct stock rom for your device.
Hit up HTC.com and enter your serial number to be absolutely certain.
Download the ROM and extract the .nbh file.
Rename it to LEOIMG.nbh and place it on the root of your SD card.
Power on the phone whilst holding the vol. down button.
It should boot to bootloader and take you through the flashing process...
Using a stock ROM will remove HSPL and whatever else... ta da.... factory perfect
Does that work even tho i have magldr?
EDIT: I have an O2 phone, not the normal firmware but one that was provider-specific, does that work, too?
Yeah, it should do.
MAGLDR runs in the chain after the "classic" 3 colour bootloader....
Try turning on the phone and holding vol down. You should get to the good old fashioned bootloader. If so, SD flash will work.
Hope that helps.
Hey that was helpfull man,thanks for that!!!
Out of curiosity, have you looked to see if the usb needs to be cleaned from dirt and lint?
A friends phone had the same problem, and would only work if held at a weird angle. I used a pin to carefully dig in the usb hole and a lot of lint and even dirt had crammed in there to stop the cable working.
just wanted to add something to this thread, correct me if i am wrong.
yes you can revert to a stock SPL+ROM+Radio using flash-via-sd-card method. so a functioning USB port is not necessary.
BUT! a fully functioning USB port IS necessary for flashing HSPL (which is the first step to unleashing yourself on all the wonderful fun possible on the HD2)
so if your USB port is faulty and you're thinking about claiming warranty, then be absolutely sure about the decision to "go stock" before you revert to stock using the flash-via-sd-card method. in case the USB repairs fail, you will be stuck with the stock SPL on there. in case you have to hold on to an HD2 which you reverted to stock but couldn't get the USB repaired, that could be a bummer if you've gotten used to HSPL and its benefits!