Related
Greets gang,
Several days ago I started getting the subject message appearing in my WinXP system tray. It was on my Gateway laptop and it would appear over and over again, citing 'Unknown Device' when you'd click the annoying ballon. My Jam wasn't even connected at the time.
I basically blew everything away and restored my laptop to factory original settings. Problem persisted. I thought it might be hardware, but the message has now disappeared, only re-appearing when I plug in my Jam. My USB Bluetooth dongle plugs in fine, no errors.
Someone else had bent pins on their USB port or plug--I see none. Anyone else have issues with this, or can anyone offer some help?
Presumably you have installed (re-installed) Active Sync on the PC? As you may already know, as standard the JAM and many other PPCs are not recognised by the computer unless Active Sync is installed [properly].
www.softick.com provide an excellent utility to have your PPC recognise as a removable drive without using Active Sync.
Yes, ActiveSync has been installed & re-installed. New development? I plugged in an 80Gb external hard-drive to that laptop and Winblows is telling me its connected to a non-hi-speed USB port, which it is not. Could be something there.
I'm going to re-flash the Jam to factory ROM, then I will dig into the USB issue.
I had this problem and I tracked it down to the fact that I had picked up the wrong cable!
Same connector but for my camera
The wrong cable thing may very well have been it, but I was also having probs with an external hard drive I was using. I ended up rebuilding my laptop twice and now things seem to be fine. What a drag.
hypr said:
Greets gang,
Several days ago I started getting the subject message appearing in my WinXP system tray. It was on my Gateway laptop and it would appear over and over again, citing 'Unknown Device' when you'd click the annoying ballon. My Jam wasn't even connected at the time.
I basically blew everything away and restored my laptop to factory original settings. Problem persisted. I thought it might be hardware, but the message has now disappeared, only re-appearing when I plug in my Jam. My USB Bluetooth dongle plugs in fine, no errors.
Someone else had bent pins on their USB port or plug--I see none. Anyone else have issues with this, or can anyone offer some help?
Click to expand...
Click to collapse
I have the same problem.
It seems, this problem appears mostly on laptops, not on PCs?
I tried to uninstall\install, repair with all ActiveSync data removal or leaving it - No result.
Also, tried to replace the cable (which is ok, im sure with the one from the camera) - No result.
Temporary way out: do Off\On with qtek9000 on cable connect.
Another way out: Turn On the "Enable all incoming beams" flag in Start -> Settings -> Connections -> Beam (this path may vary depend on your Universal brand name). As I seldom need to connect via IR to other devices, I have switched this option off to consume power.
DOES ANY BODY KNOW, HOW TO FIX THIS BUG?? Any Ideas?
Qtek9000 with laptop Toshiba Satellite Pro \ Win XP SP2
it seems dat a noob like me at last can give a help
i have the same problem last time, and as i trace it down, the problem lies on the cable.
as u know that we all use mini usb (usb cable type b) for our o2 mini, but not all type b cable support pc connection, some will only give charging access
i have 2 mini usb cables, one comes from my external hdd, and the other is i buy it myself. the difference is that the 1 i bought actually have a shorter connector (maybe the problem due to this)
so try to buy another cable, as i don't know any other way (reinsatalling pc os, hard-reset device or reinstalling active sync won't solve the problem)
NB. both cables are working when i plug it to my external hdd, so maybe the cable is not faulty. one of the advantage that i got is that i can charge my mini without disabling the active sync usb connection
sorry for my bad english
i can almost essentially confirm that it is NOT the usb cable.. I have been using a usb cable i had around the house for syncing my phone, and it has worked perfectly ever since I first received the phone (over half a year ago), but all of a sudden, i plugged in my device, and received the "usb device not recognized" error message... does anyone know the cause of this?
Ok, ive got activesync working fine on one of my pcs but on the other it disconnects after about 3 mins. both have identical software antivirus/firewall-wise the only difference is one has a hardware modem/wireless router(the non-working one) and the other uses a wireless usb hub to connect to the internet.
Ive tried pulling the ethernet cable from the back of the non-working pc to no avail, disabling windows firewall etc but nothing stops it disconnecting after about 3-4 minutes.
Ive tried all the suggestions regarding tcp/ip, they were already correct as were the dhcp ones.
im completely baffled by this
the wmstorage program works for a bit longer but gives the error "the device is unavailable due to an i/o error" after about 5 minutes
anyone have a clue why this is happening?
Odd question to ask. Is your unit set to switch off after 3 mins? Just check if the device is on/off (you can have the backlight off, but you should able to see something on the screen) when the activesync disconnect.
on battery power its set to 2 mins but on external (usb?) its unticked. it works ok on the other pc though thats the thing so i assume its a pc settings issue :wink:
As you plugged into the PC directly (not through a USB Hub)? USB hubs have been known to cause problems.
im using a usb extension cable straight into the usb 2.0 card , the only other device is a printer and the keyboard which share a usb hub on another port.
The cable works fine with other devices ie digital camera/camcorder so its not a faulty cable.
Im using a hub on the pc that works (and its only usb1.1) and it shares with the wireless dongle
One thing i did used to get while transferring data was the avg email scanner popping up while my ipaq (which worked fine) was connected. i disabled the email scanner to see if it helped and rebooted but it was no different
ok-think ive fixed it-the (brand new) usb cable must have been faulty cos i connected the mda cable straight into the pc and it worked :roll:
thanks for all your help :wink:
Hi, my activesync doesn't work, but it is charging...
i tried other USBs and i tried different PCs and same thing happens..
tried to take off the advanced network functionality...
Does anyone have a solution to that? please please help me im begging
Thanks alot in advanced!
anyone???? pleasee??????
go to active sync on the Hermes and delete the old profile. This may work...
Cheers...
tried.. doesnt work.. plus it didnt even work the past couple of roms that i had... i think since i upgraded it from wm6 to wm6.1 i started getting this issue..
any solution????
if trying to connect it to another computer dont work
i would suspect a faulty connector
so how is it possible that its charging??
To charge, all it needs is for the pins carrying voltage to get a connection. (All USB has a 5v current at 500mA, it just uses that to charge).
It could be that one of the data pins used by USB solely for transferring data are damaged or broken (or the connector is broken internally). This is almost impossible to diagnose without the correct tools, so I'm guessing here.
However, my Hermes' USB port has started to 'act up' - it still charges fine, but you have to have the USB cable at juuuust the right angle and you can't move it or touch it at all, otherwise the USB connection disconnects. I suspect either oxidisation on the terminals or a dodgy USB connector - but as long as it charges alright, I can live with that!
you could try cleaning the contacts with a cotton bud and some isopropyl alcohol (surgical spirits - NOT METHO). If there is any buildup on your contacts this will fix it.
Cheers....
Mine has done this many times before, the bloody pc rejects the usb device as unknown. [email protected] frustrating, I go in and delete all stored data about the phone and same on the PC in Active sync, some times works. Try different cables, sounds weird but some work well some are no good, dunn'o why, just does. I would perform a Hard Reset, I have done this once and it fixed it, blows away all your stuff (which should be on your 2Gb min mem card anyway). Good luck, sounds like a Hard Reset is where your headed.
is it possible that its not working since i switched to WM6.1? cuz i dont usually charge my phone through the pc and i just relized it a month ago... so if i switch back to wm6 do you think it would work??
Try this
Try and going to ur Start Menu,and then into Settings,go into the last tab "Connections", now go into the little icon titled USB to PC,and make sure the little box is UNCHECKED...well now that should do the trick
aaronc29 said:
Try and going to ur Start Menu,and then into Settings,go into the last tab "Connections", now go into the little icon titled USB to PC,and make sure the little box is UNCHECKED...well now that should do the trick
Click to expand...
Click to collapse
if you would read the first post... where i actually asked the question u would see that i tried that already
but tnx for trying
my 8525 does this from time to time as well, while I've never traced down the exact problem, a soft-reset almost always fixes it (I'm not saying you haven't soft-reset, it's just how I fix mine).
It likely has something to do with memory, as it usually happens after I've been using a lot of features (windows live search, outlook, etc.) and haven't reset in several days.
good luck....it is frustrating!
u did not described what it actualy does if you connect it to the pc and what rom are u using
the common problems with wm6.1
uncheck the advanced usb disconnect from pc restart pc
go to active sync on ppc seting - connection uncheck box (allways) check box open `usb close `usb ok reconnect ppc
the wording might be different cause im using right now diff. language
I just tried to plug my phone in today, and activesync does not detect my phone when I plug it in.... Activesync usually works great for me.
So far I have tried:
1. soft reset phone
2. attach wife's phone - still no sync (this leads me to believe it is a problem on the PC - not the phone)
3. remove and re-install activesync on the pc
4. restart the PC
The USB connection is definitely being made - as when I plug the phone into the computer it starts charging the battery..... but no activesync session is initiated, so I can't modify any files on my phone....
any other ideas?
Hmm that is bad... Well what do you use activesync for? Transferring files or for internet sharing?
All I can think of is maybe a virus? Run avast! virus cleaner. It's the stand alone virus cleaner not the actual anti-virus program. It won't install anything on your pc and it's actually one of the best. Just go to Avast.com.
If you use activesync for internet sharing you actually don't need it . I don't use it for internet sharing. You just need the drivers. I use wm5torage to put stuff of my memory card.
Hope something I wrote helped.
Uncheck start>settings>connections>usb to pc.
never mind........ I guess my data cable just went retarded.
I bought a new USB>MiniUSB cable today and activesync loads right up.
strange, since the original cable does not look like it is damaged at all, and can still charge the phone.
Oh well - all's well that ends well. lol.
zaep0b said:
never mind........ I guess my data cable just went retarded.
I bought a new USB>MiniUSB cable today and activesync loads right up.
strange, since the original cable does not look like it is damaged at all, and can still charge the phone.
Oh well - all's well that ends well. lol.
Click to expand...
Click to collapse
i bit late to the party,me ,but this is a comon problem in certain devices,so far i changed 4 cables with my hermes.
oh well. good to know anyway.
I work as a manager at a retail store, and found a couple of PSP data cables (the exact same cable that HTC phones use, surprisingly) that were in the back room which clearanced to 10 cents.... I bought them out - so I have a TON of backup cables in case I ever need them. LOL
the problem is not the usb cable per say but the usb hub in the device.
the new htc hub since the Hermes have a low threshold for wear, the pins that is, so when your usb cable gets used for awhile it wears out a bit also,this gets to a certain stage the the pins no longer touch each other therefore this problem occurs .
i have noticed that my wife 3 year old wizard has a standard usb plug and we never had any problem with any cables,even using the cables that do not work in the hemes that started showing that problem after 6 months of usage.
yeah - well maybe I'll be lucky and the cables I bought (from the PSP) don't have this wear and tear problem
hi guys,
i have searched the forums for wm 6.5 ROM, but lots of them are still in beta phase,have bugs or slow.
can anyone give link to a stable WM 6.5 ROM for my xda orbit
Thanks in advance
...
6.5
Babbelut ROM WM6.5-28005 v0.3 NLD/WWE
*spb mobile shell is great, he is currently developing beta rom
http://www.sendspace.com/file/97d3p7 (download link for v.3)
http://www.megaupload.com/?d=ZTXWO4D7 (download link for v.Beta)
Downloading it now, will check it later on. THX
Was about to create topic but found this and hopefully will try this and hope it works on my XDA Orbit 2. I brought it off Cex from Aylesbury and it needs some love and update as i have Windows Mobile 6.1 (eeurrgh) and brought it off cos i thought i can upgrade to Winodws Mobile so i hope these works well for me.
Any introductions of doing that?
Thanks in advance.
First link didnt work. The XDA tried to block it by restarting it themselves. Tried third time. And unlucky.
Second Link. How can i use NBH file for my XDA?
...
Wrong place dude..
this is for xda orbit 1/artemis..
your looking for xda orbit 2/ poloris..
you need to be here..
Rn
Hi all I'm new here. My phone "O2 XDA Orbit" behaving strangely. Suddenly the sound disappeared and I can not hear phone calls directly into the phone, and any other person hears me not(microphone off), and not just one click sound on the screen. If I restart the phone with USB cable inserted into the phone and computer (on), then the sound occurs again(but not in original style, sound occur in to the back speaker not in front ), and phone function almost normally with microphone (on)>>> until the next reboot when sound disappear again and microphone is off. I mention that;.... connection the phone to the computer can not be achieved in any of this cases. The error code (USB connection) connection on my computer is {Code 10(One of the USB devices attached to this computer has malfunctioned and Windows does not recognize it)} who can not recognize the new hardware. In your opinion of specialists in this field what would be done? I think something happens to the ROM which gives errors of hardware power. The sound occurs when I insert into the phone power charger connector and disappears when the power supply plug out ... Please if you can help me with some guidance what I have to do one upgrade of ROM or something? Specification of the phone is:
[*]IPL-3.04.0001
[*]SPL - 3.04.000
[*]OS - 3.4.0.0
[*]CPU - OMAP850
[*]Speed 201Mhz
[*]RAM 64Mb
[*]Flash 128Mb
[*]Data bus 16bits
[*]ROM 3.4.206.2WWE
[*]ROM date 4/18/07
[*]RADIO Vers. 02.67.90
[*]PROTOCOL Vers. 4.1.13.28
[*]EXT. ROM.Vers 3.4.206.101
[*]MODEL of phone -ARTE200
[*]Platform - PocketPC
Funny ...!!! Today I put the phone to the charger and after I removed the plug from the power supply, the sound has returned, but the USB connection to a PC still can not set ...! What should I do? A new version of Windows can install on my phone; without connecting the USB cable to the phone(ex.-of my card micro SD)??
Adryum said:
Funny ...!!! Today I put the phone to the charger and after I removed the plug from the power supply, the sound has returned, but the USB connection to a PC still can not set ...! What should I do? A new version of Windows can install on my phone; without connecting the USB cable to the phone(ex.-of my card micro SD)??
Click to expand...
Click to collapse
have you got activesync or windows mobile device centre installed on the pc?
if yes..
i suggest you buy a new usb cable.
i have this problem with a couple of cables.
"USB DEVICE NOT RECOGNISED"
but when i change to a differant cable, everything is ok.
flashing via micro sd - upgrading windows.
have you done uspl 1.11.cmon?
Thanks for your attention Raving in the first place ...! Data cable has no damage that I checked the same cable with my photo camera and it works normally with PC and I have two more data cables and the problem is the same. It seems weird that the phone do some work once, ...once not. It starts when he wants the sound, and can not find any explanation ... In contrast with the USB connection can not establish anything, something happens to the sound module and USB ...PC see's something, but it's not sure what it is, and says he can not establish connection with the new hardware and it gives me error "CODE 10". in Universal Serial Bus Controller and the Active Sync is instaled on my PC but he don't say a word about this connection...I don't know on what to do...! I must mention that this oddity occurred only three days go and without them I do something wrong ... He grabbed him crazy after a normal operation for a year and a half, because we had no problems with it until now ... I used as a GPS and the phone and I was really pleased with him. By the way, what they mean uspl 1.11.cmon? All data of my phone are in the first post.The phone it was once unlocked by someone else, and now I can use any SIM card from any GSM provider..............I forgot to say that I've rebooted 2 times in general mode and now works but without USB connection sound when he wants it or not................But I think she has lost some registry ...!!!
click 1.11.cmon in my signature.
this will divert you to a tutorial thread.
when you can connect your device to your pc successfully, you should do the uspl 1.11.cmon but not for now. do not try and flash a rom yet either, you will break your device. (thats what uspl 1.11.cmon is for)
id like you to just try the "hard reset".
back up all your data first.
bookmark the page as ill be updating it regularly.
personaly i think its your usb cable, eg:
one of my cables works with a micro sd reader but not my for my device, i understand your cable worked but now does not.. however thats what happened to me.
Sound engages when he wants and where he wants. If I restart the phone, sound disappears and microphone stop; and I can not talking on the phone. Enter data cable from PC to phone, and give the phone restart. Once the phone is starts, sound appear but only in back. When talking on the phone sound very loud and sounds of the touchscreen controls can not disconnect the rear speaker who remains engaged and does not want to disengage it from the normal operating mode. Another job here would be that when inserted in the charger cable, the sound is right: each speaker and microphone or operational. If I remove the plug (charger) of phone then the phone function normally just like before, but without USB connection. If I plug "USB cable data" on the phone, to the desktop I see message "One of the USB devices attached to this computer has malfunctioned, and Windows does Not Recognize it. USB Device not recognized." If I unplug USB cable from phone the sound disappears, and what I have to do is to start over again.......!!!!!!!!!
I tested all data cables, and are ok. The problem is hard. The hardware has a technical failure which somehow blocks the data on USB. Battery power consumption is higher and the battery is discharged rather quickly than it was before the cage. At night when I charge the battery full, morning at 10:00 is only 30/40% of capacity. But what is even stranger is that: when I connect phone to PC, in device manager shows me the new hardware (Mobile Device) but after a few seconds there appear a connection error code (CODE 10) that is the hardware can not start. Active sync has not started when the fault occurred..... In your opinion what should be done in this case? ... Should contact a service or ... in any way I can test something before others get the screwdriver into my phone?
sabih00 said:
hi guys,
i have searched the forums for wm 6.5 ROM, but lots of them are still in beta phase,have bugs or slow.
can anyone give link to a stable WM 6.5 ROM for my xda orbit
Thanks in advance
Click to expand...
Click to collapse
Thanks, i will test...
The connection was made the first attempt. After a week of "digging" through all possible places I noticed that the connection was obstructed by the firewall.PFFFFFFFF ..... Finally found! The FIRE WALL(on PC) settings to be set: ADD PORT------ "Outbound UDP ----5679" -on exceptions tab....See this:http://www.microsoft.com/windowsphone/en-us/howto/wp6/sync/activesync-troubleshooting.aspx?WT.mc_id=FWLink
TKX Raving U're the best...
...
Adryum said:
PFFFFFFFF .....FIRE WALL
Click to expand...
Click to collapse
lol, i didnt think about the fire wall being the problem.. typical that it was something that simple.lol although it did sound like a dodgy usb cable..
thats something ill remember
have a good new year dude!
guys i am having a problem....whenever i try to install any ROM i get error 224 device not responding......my htc is connected through activesync.....what can be the issue...i am using windows 7.
..
raving_nanza said:
ERROR [224] : DEVICE NOT RESPONDING
check the ActiveSync connection and run RUU again. if problem continues, uninstall active sync and re-install.
Click to expand...
Click to collapse
1. unplug device
2. re-connect device to pc
3. wait for active sync/wmdc to connect
4. run ruu
5. if error continues unplug device
6. uninstall active sync/wmdc
7. re-install active sync/wmdc
8. restart pc
9. go to step 1.
Rn
quertz?
Hi raving nanza,
you did a great work with BAB v03.
It works great. sometime the touchpanel reacts slow but good.
But i can't change my touch keyboard from qwerty into qwertz.
HKEY_LOKAL_MACHINE\System\CurrentControlSet\Control\Keyboard Layout\"Active" is "00000407"
Thats the German code - but still having Qwerty?
HKEY_LOKAL_MACHINE\HARDWARE\DEVICEMAP\KEYBD\"TaskManVKey" is "0x23"
HKEY_CURRENT_USER\keyboard layout\Preload\1\"default" is "000000407"
What to do?
...
che.bike said:
Hi raving nanza,
you did a great work with BAB v03.
It works great. sometime the touchpanel reacts slow but good.
Click to expand...
Click to collapse
thats Babbeluts rom, not mine!
i merely suggest it to the other users
ill look into your qwerty to qwertz keyboard, when i find out ill post it here and ill update the tips&tricks thread
Rn