Database Users

Bricked my S200 after installing jasper AKU3.3 plz help!

hello all,
i'm a newscommer on this forum,i've trust in upgrade my phone with aku3
i correctly followed the topic , install step 1 (forG3) and step 2
my device worked fine after the first install (qteck 2.15 fr ->2.2 from step1)
i've synchronize my phone, and run the second part, installing without problems, reboot > freeze on the boot screen htc
no way to synchronize again. my phone is reconized by mtty (1.51 and 1.50) but i don't know how to use it
ipl 2.09
spl 2.20.0000
gsm 02.47.21
os 3.0.0.0
i've tried all the night to find a solution on all forum i knew, i drive me to this one, i think it could help me best ( you'r pro dudes )
but i'm allways stick. i've call htc division hotline (i'm from france) , they said i have to send back my phone ( but he's now out of waranty, cause it's not a legal rom i've installed, so i have to paid, and i've allready too much invest on my device)
plz said me there is still a hope!

did try upload another rom from bootloader ?

did try upload another rom from bootloader ?
but first try a hard-reset

i don't know how to load a rom from bootloader (i allready have made soft and hard reset

no one could help me ?

1. dowenload this latest Qtek official rom from here: ftp://xda:[email protected]_220734_2207114_024721_QtekWWE_Ship.exe
2. enter your S200 into bootloader mode by pressing power +camera + reset, let go of the reset, but keep holding power + camera until the three colur screen will show up (that is bootloader mode).
3. connect the S200 to your pc (make sure your battery is fully charged)
4. run the Qtek official rom.
5. good luck!

i've tried those kind of upgrade several time, but without possibility of establishing an active sync connexion, it's impossible to launch the rom install...
does samebody knew if it's possible to make a rom dump with an emulator and copy it on a sd card for autoinstall backup in bootloader mode ?

while in bootloader you don't need to establish any activesync connection. just plug the usb cable, then if appears "usb" on phone you are good to go.
install the original DOPOD rom from the ftp.

this rom don't work, it give me the message
error 294 invalid vendor id

it's now working ! great !
i've juste install again the step one of jester's aku3.3 (so, i'm on a 2.20 os, i think i'll keep it for a while )
thank you verry much

pti_nourson said:
it's now working ! great !
i've juste install again the step one of jester's aku3.3 (so, i'm on a 2.20 os, i think i'll keep it for a while )
thank you verry much
Click to expand...
Click to collapse
So you can now change your signature again, right

Cincular 8525 stuck in Bootloader

I have a Cingular 8525 running WM5 that is stuck in bootloader screen. I have tried to soft and hard reset ... just boots back to the same screen, I can't turn it off once in the screen and when i sync via usb to the pc i get the message that the "usb device that is connected is malfunctioning" I have not done any upgrading at all and the phone worked perfectly right up till the time i powered it down and restarted into the bootloader screen.
Please can someone out there help me with this issue?

Zulu137 said:
I have a Cingular 8525 running WM5 that is stuck in bootloader screen. I have tried to soft and hard reset ... just boots back to the same screen, I can't turn it off once in the screen and when i sync via usb to the pc i get the message that the "usb device that is connected is malfunctioning" I have not done any upgrading at all and the phone worked perfectly right up till the time i powered it down and restarted into the bootloader screen.
Please can someone out there help me with this issue?
Click to expand...
Click to collapse
same problems, run perfect before with schaps wm6 rom then flash to faria wm6.1... not feel good with faria. try to flash with other rom then the problem start ..
how to recover ....... please help

Asfarizal said:
same problems, run perfect before with schaps wm6 rom then flash to faria wm6.1... not feel good with faria. try to flash with other rom then the problem start ..
how to recover ....... please help
Click to expand...
Click to collapse
Manage to solve the problem ...thanks WIKI !!
Go to Bootloader mode: Hold side OK and POWER buttons together and reset with stylus
Then Flash to any ROM you want !!

Thanks .... But
Thanks for the reply ... but i have no idea how to do what you tell me, I am new to all this phone "stuff" as a matter of fact this is the first time that i am ever using one of these forums. I have read till i am cross eyed but dont actually understand what you are talking about ... now don't let that scare you away as i am willing to learn and i am not braindead ... you all had to start sometime in this, not so. I get that i need to try and reflash my rom...
so is there some type of rom update software that i need? ... what is a hard SPL?? ... and who is Schaps?? .. sorry guys to do this to you but i would like to get into this game and i need some ( well maybe a lot ) of pointers.
Thanks for your time.

1. Search for "mr vanxs guide" so you have an idea on what you're doing.
2. OK, as Asfarizal said "Go to Bootloader mode: Hold side OK and POWER buttons together and reset with stylus". If you cant work out what the buttons are, go to the manual. it will tell you.
3. type in "hard SPL" in search on the forum & download the .zip or .rar file. this should have 2 files inside when opened,
a). RUUWrapper.exe and
b). RUU_signed.nbh
sync Hermes and double click .exe file. follow prompts.
4. find a rom that you want (would suggest TNT SE as a fairly good rom for noobs... good and stable, no problems...) Again download, then (and this is personel preference) format an sd card fat 32 and copy RUU_signed.nbh into root directory. Rename it Hermimg.nbh. Put into Phone and put into bootloader(make sure the battery is more than 50%) follow prompts. This should get you out of trouble. You can also sync your Phone and double click on the RUUWrapper.exe HOWEVER, if you should reset your computer, pull out the usb cable or have anything else happen to the computer that interrupts the flashm, you could end up with a worse brick than you have now. try to read up on flashing (search for "mr vanxs guide") and this should help you a lot if you have other questions. Good luck and happy flashing......

Thank You
I will follow the instructions you gave and try to get it going this weekend.
Thank you so much for your time

Zulu137 said:
Thanks for the reply ... but i have no idea how to do what you tell me, I am new to all this phone "stuff" as a matter of fact this is the first time that i am ever using one of these forums. I have read till i am cross eyed but dont actually understand what you are talking about ... now don't let that scare you away as i am willing to learn and i am not braindead ... you all had to start sometime in this, not so. I get that i need to try and reflash my rom...
so is there some type of rom update software that i need? ... what is a hard SPL?? ... and who is Schaps?? .. sorry guys to do this to you but i would like to get into this game and i need some ( well maybe a lot ) of pointers.
Thanks for your time.
Click to expand...
Click to collapse
Looks like you've got a lot of reading to do, and a problem to sort out. Firstly a couple of answers...
Schaps is a Rom Cooking guru (makes custom versions of WM5, WM6 etc). When you get your phone sorted out I'd recommend trying one of his roms.
Hard SPL. The SPL is part of the bootloader which effectively dictates how a rom is flashed and what roms can be flashed. HardSPL is a custom version of this which allows you to flash any rom from any carrier. It also protects against a bad flash in many cases. It is recommended before you try flashing any new roms or radio roms. Use Hard-SPL-V7 at the bottom of the first post here.
The Rom upgrading software is contained in any of the cooked or carrier supplied roms. It is normally a .zip file which cotains 2 files: xxxxxRUU.exe and RUU_signed.nbh. You run the .exe file from your PC when connected to your phone via USB. More details of how to do this are in MrVanx's guides. Also other resources here.
Now to try to sort your phone out...
What is displayed on your screen when in bootloader mode? It should be something like this:
HERM200
IPL-1.04
HERM200
SPL-2.10.Olipro (This is HardSPL V7)
If you don't have an Olipro SPL then you need to get HardSPL onto your phone. If you haven't done any upgrading and have had the phone from new then I guess you don't have hardSPL.
Now you need to fix your USB Malfunctioning problem. I can't help too much here except to suggest trying a different cable, different USB port or different PC. Also, if you are running Vista try an XP maxhine. When you connect to the PC does your phone show Serial or USB on the screen? If you can't get a USB connection, all is not lost - you can re-flash your rom using an SD card, method here.
There is a thread about un-bricking phones which may help.
There are various diagnostic tools (which can also screw your phone if used incorrectly). The favourite of these is MTTY but you need a USB connection to use this.
If your phone is in warranty I'd recommend getting your supplier to sort it out, but if not I'd try to re-flash an ORIGINAL supplier rom (Cingular I guess). You can get links to the official supplier roms here.
I think (might be wrong) that sometimes when stuck in bootloader you need to flash an official rom, not a cooked one to recover your phone - then you can run HardSPL and then flash cooked roms again.

Cingular 8525 stuck in bootloader
Thanks for the reply ... lots of great input.
Now to answer some of your questions.
1) When I power up the phone (only pushing the power button ) it goes straight into the bootloader screen without pushing any other buttons, and it displays
HERM100
IPL-1.01
HERM100
SPL-1.06
Then at the bottom in the white bar it says "Serial"
The only way that i have found to power it down again is to remove the battery, there is no response from any single buttons after it is in bootloader
the soft reset and hard reset work but it just goes right back to the bootloader screen after.
2) The USB malfunction. This only started after the phone "crashed" and before that it worked great ... well i only used it to sync up to my work pc for the contacts and to get pictures onto my hard drive.
all the PC's that i use are running XP. I have tried my home PC and my Laptop
and the work PC and all of them have their own cables and they all say the same thing ... "the USB device is malfunctioning"
I am sure that when i get the phone going again the USB will start to function again.
3) Phone warranty ... I bought the phone off e-bay from a store in new york about 10 months ago as a "new unlocked cingular 8525" it was new and unlocked, but i have no idea how they unlocked it. I would assume that there would be no warranty now and in any case i live in Canada and would have to ship it down to the states to an AT&T repair center and that sounds like a nightmare to me with the customs and so on.
I will give you a little more background on the problem. the phone worked like a charm without any problems at all for the 10 months that i had it, then the morning of the crash the phones alarm did not go off in the morning and i was almost late for work ... i did not pay it any further attention untill at 3:26pm
that afternoon the alarm went off ??????? (it was set for 6:05am) so i checked the main clock time, it was right. I then checked the alarm time, it was right ??? So i figured that something must have just got confused, so i powered down the phone with the power button to just restart it and while it was powered down i removed the battery to take the oportunity to to clean all those fuzzies and dust that collect in the battery compartment out and put it all together and powered it up again (just by pushing the power button) and this wierd red, green, blue and white screen appeared and that is all that i have seen since ???
I hope that answers your questions and i will start going through the links that you sent and get to reading ... will there be a pop quiz ... lol
Thanks again for your time and i very much appreciate all the time that all of you have spent on me and my phone ..... I know that you all just feel bad for me because i now have to use a Motorolla V551 ... lol

Great Work
ultramag69 said:
1. Search for "mr vanxs guide" so you have an idea on what you're doing.
2. OK, as Asfarizal said "Go to Bootloader mode: Hold side OK and POWER buttons together and reset with stylus". If you cant work out what the buttons are, go to the manual. it will tell you.
3. type in "hard SPL" in search on the forum & download the .zip or .rar file. this should have 2 files inside when opened,
a). RUUWrapper.exe and
b). RUU_signed.nbh
sync Hermes and double click .exe file. follow prompts.
4. find a rom that you want (would suggest TNT SE as a fairly good rom for noobs... good and stable, no problems...) Again download, then (and this is personel preference) format an sd card fat 32 and copy RUU_signed.nbh into root directory. Rename it Hermimg.nbh. Put into Phone and put into bootloader(make sure the battery is more than 50%) follow prompts. This should get you out of trouble. You can also sync your Phone and double click on the RUUWrapper.exe HOWEVER, if you should reset your computer, pull out the usb cable or have anything else happen to the computer that interrupts the flashm, you could end up with a worse brick than you have now. try to read up on flashing (search for "mr vanxs guide") and this should help you a lot if you have other questions. Good luck and happy flashing......
Click to expand...
Click to collapse
Thanks a lot man & great work i unbricked my Herm100 with method u mention above thanks a lot & great job keep it up

I also have this problem.
I d/l Hard-SPL-V7
and when i run RUUWrapper.exe
I get an error saying the application failed to initialize properly (0xc0000135)
What's going on?
How do i fix this?
this happened when i was trying to unlock the phone.
Thanks

need help
when i switch on my orange herm100 it shows On the bootloader screen is displayed:
HERM100
I PL-1.01
HERM100
SPL-1.40.01ipro
history : i buy unlocked orange phone
fewdays back i found no imei ,
yesterday i try to flash by micro sd but in gsm stage its gets hang no progress after extrom stage
IPL - OK
BOOTLOADER - OK
SPLASH1 - OK
SPLASH2 - OK
EXTROM - OK
GSM - (NO ACTION)
OS -
i tryed several time no action, i cant connect by mini usb.
PLEASE help me
tell me which it the right rom to chose? step by step procedure..
how to rectify imei?
thanks and regards
kirtibas

kirtibas, sorry it took so long to reply, 1st thing I'd do is upgrade to SPL 2.10 olipro. This is safer to use than others. then I'd suggest reflashing a stock rom to see if that works. After stock rom works then use a cooked rom as your heart desires... Cheers...

XDA ORBIT not able to flash ;(

Hy..
belive me.. i tried nearly everything... and ive been through all of these posts... but i dint find anything helping me out with my problem...
ok, i try to explain in a short way!
I want to upgrade my "old" xda orbit (rom: 3.4.207.2GER, Rom Date: 18.04.07) wit a new rom ( something like "Artemis_Touch_4.02_Full_with_4_sided_cube")
BUT IT DOES NOT WORK!
Yesterday i updated my "new" DIAMOND to a new rom (Bepe 0.94)... so i basicaly know what to do..
But my ORBIT doesnt like to be upgraded..
USPL: doesnt work
RUU: doesnt work
Artemis_Touch_4.02_Full_with_4_sided_cube: doesnt work
downgrade to wm5: doesnt work (dindt find the correct one, i guess...)
now i am out of any more idears... ive got a lot of error messages... such as 260, 270 corrupt files, and many more...
wonder why my orbit is still running after all these unfinished and unsucessfull "updates" but still running with original german O2 WM6 system.
Does anybody can give me a hind what do do, how to update or where to look?
Thanks a lot...
Using Artemis USPL: in the DOS window always the message "program cannot be found".. running aprox up to 50% and stops, than closing the DOS windo
the orbit stays, after a short action showing the Linux guy, with a "white/black" display..
than using the RUU: still connected via usb to my pc.. still black display..green LED on top of the device on..checking the rom.. showing mine correct (3.4.207.2) to 9.99
clicking "next": starting updating... pda display gets threecolored.. than gray.. showing 99% and than 100% after just a few seconds..
Prog stops.. telling me that the file is corrupt (Error 270).. my device reboots and starts with the O2rom
I downloaded the Artemis USPL several times from several locations.. always the same message...
Hard to explain.. but i hope you got my point?!
Btw.. thats just one of the ways i tried.. and just one of my errormessages..
Thanks

Did you tried to remove your SD card before you flash?
Cheers

I Got It I Got It
Thanks "Zecanilis" for your answer.. but that was not my problem.... i took out the sd card as well as the sim card.. as i said.. i tried nearly everything!
But this morning ( i spent the whole night in front of my computer ) i foud the mistake.... an easy one!!
The "Artemis_USPL" file, you can find in all of these threads, is not working with my devices (pc and/or ppc)!?! i dont know why.. but it doesnt.
As i told you i always got messages in the DOS window "program cannot be found", "program cannot be used"... and the intallation skipped all files and stopped always around 50%.
but at 3 in the morning i found a USPL file in the net, with a different name, and it worked with the first try!!
The File is named "arte_uspl".
Just worked fine and smooth 10..20..30....... finisehd.
I am able now to install any rom I like!
Btw... i swithed to Mossis V2.2Ger - a very nice one i think.
But maybe i'll try some more...... because i am able to!
Take care and a lot of fun with your devices!
Bobo

I have the same problem
Where can i find/download the "arte_uspl"?
Thanks for your help.

well...good question
i didnt write down the link.... i dint save the link... sorry!
what i did was to save the file on my computer!
i tried to uplad it to this post... but it didnt work?! sure i am to stupid to do it right!?
so plase help me to post it here, and i will do so!
or gimme a mailadress to send it to!
sorry for beeing so stupid!
greetings

orbit do not boot, do not flash
Hello,
i am searching for a solution of my problem:
i updated my orbit with the new mossis ROM and everything was well, and i used my orbit after this update!
Yesterday i Reset my device and after this the orbit dosen't start again!
After showing the bootsplash the device hangs
So i try to flash the device again:
first i try this:
- start the bootloader manually (voice button + reset)
==> shows: IPL 3.04.0001
SPL 1.11.0000
- starting the ROM Update Utillity
==> the screen of my orbit is grey and shows the update bar (0%)
==> RUU shows the following mesage: ERROR[300]: INVALID UPDATE TOOL
(i used the original german o2 update file)
second try:
update with the SD-card:
- SD-card (512MB) formated with FAT32
- copy the image file xxxx.nbh to the SD-card and rename it to ARTEIMG.nbh
- start the bootloader manually (voice button + reset)
==> screen: Checking SD contens
==> Update SD Image?
- bushing the volume down button
==> screen is red green blue and shows IPL 3.04.0001 and SPL 1.11.0000
Update flash do not start!!!
if i try this sd-card based update with the RUU_uspl_signed.nbh file, the device bootloader start and update the ROM
have anyone an idea???

ohs said:
Hello,
i am searching for a solution of my problem:
i updated my orbit with the new mossis ROM and everything was well, and i used my orbit after this update!
Yesterday i Reset my device and after this the orbit dosen't start again!
After showing the bootsplash the device hangs
So i try to flash the device again:
first i try this:
- start the bootloader manually (voice button + reset)
==> shows: IPL 3.04.0001
SPL 1.11.0000
- starting the ROM Update Utillity
==> the screen of my orbit is grey and shows the update bar (0%)
==> RUU shows the following mesage: ERROR[300]: INVALID UPDATE TOOL
(i used the original german o2 update file)
second try:
update with the SD-card:
- SD-card (512MB) formated with FAT32
- copy the image file xxxx.nbh to the SD-card and rename it to ARTEIMG.nbh
- start the bootloader manually (voice button + reset)
==> screen: Checking SD contens
==> Update SD Image?
- bushing the volume down button
==> screen is red green blue and shows IPL 3.04.0001 and SPL 1.11.0000
Update flash do not start!!!
if i try this sd-card based update with the RUU_uspl_signed.nbh file, the device bootloader start and update the ROM
have anyone an idea???
Click to expand...
Click to collapse
Dear ohs,
There are many ppl, who have this Error 300 issue, but there is no help/solution available anywhere. Maybe the best option is to send your device to HTC, I guess they'll replace your motherboard, if in warranty you'll be lucky!!! unless they find out if you have messed up the device

xda orbit
same problem here,i tried eveything,my xda orbit wont flash it starts to instal the new rom but when it reaches 3% it resets himself ...any sugestion guys ? i tried upls,hard-spl etc arthemis rom everything . help please

Guys, I would suggest, if your device is under warranty, do send it to HTC Service center rather than breaking your head with it. Even I have been through such problems but ultimately I sent it to the service center and expecting my device in a couple of days with a motherboard changed.
If your warranty is not valid anymore then you are in trouble.
Good Luck

Xda Orbit
dose anyone knows the right stepts to flash this Xda Orbit German rom with a wwe rom ? please post it so we can try,i have this xda for 1 year now and iam still using the german rom on it,i what to start to use it but what can i do ? learn german ? somebody help ! i tried to flash it with RUU_Artemis_O2_UK_3.4.206.2_4.1.13.50_03.06.90_Ship all gose well untill 3 % from update the xda resets and gose back to his rom,please help me out ! i`ll mae a donation for this cause ! Thanks

arte_uspl
bob75 i found the rar arhive for your arte_uspl the link is : http://rapidshare.com/files/36943423/arte_uspl.rar

please help!! after ROM upgrade the device stuck completely!

please expert guys help ...
i have new leo with ROM 1.43 today after trying to upgrade to ROM 1.66 I did everything as asked, the installer began , with all the colours on the leo display then it started the percent completion counter , and after 2% it wrote me error something , and the leo restarted but stuck in the white start up menu with the green HTC icon and below the R G D information but the device doesnt proceed further and stuck here !!!
please help !!!!

it write me as i recall
it wrote me if i recall right :
INVALID MODEL ID

did you install HSPL before trying to install the ROM?

no i didnt try to install anything !
no i didnt try to install anything ! , just started the intallation file ROM arabic-english , and did what i asked to do !

if i didnt install hspl what can i do ?
can i take the device to the shop i bought it from and use the warranty ?

well, no...did you get the file from HTC direct or off here? your phone could be vendor locked to your provider so if you can get the original ROM that was on your phone you can flash that back on...
you should really read into things before jumping in at the deep end...

well i have an inlocked device ...
o bought the device in europe , but i am from israel , htc sent me notification about new arabic ROM with link , i tried with my serial to download but couldnt , it wrote me "this upload not compatible with ur device" , i downloaded it from here XDA developers , but it went wrong !! , the problem that the phone stuck in the loader menu , before uploading the sense interface , and i have no connection between the pc and the phone "no active sync" so how can i reinstall the older version or make the phone load again ?!!?!! plz help !

you need the original ROM and a connection to your PC. run activesync as even not working it should connect up...

no there is no connection the device centre says not connected
the phone is not responding and the pc doesnot establish connection with it , i am stuck with loading menu with the R 2.04.50.22~2
G 15.26.50.070
D 1.43.7024
from there nothing moving , if i do soft reset it , it stucks again in the same menu !!!
i didnt install HSPL , and i guess i tried to install not the correct region ROM upgrade , the phone was purshased in lithuania , but htc offerd me middle eastern ROM because i want the arabic - hebrew support !
plz help

You could try installing the Shipped ROM via microsd card method. Just make sure your battery is above 50%. then follow these steps:
1. Using 7Zip, Open your Shipped ROM.exe (You need your exact shipped ROM for this, anything else will give you the error you got)
2. Look for the "RUU_signed.nbh" (without the quotes)
3. Copy RUU_signed.nbh to your microsd card AFTER formatting the microsd as FAT32 (quick format works well enough, using Win 7)
4. Rename 'RUU_signed.nbh" to "LEOIMG.nbh" (again, without the quotes)
5. Take out the HD2 Battery and insert microsd card in slot.
6. Put Battery Back on and hold the "Vol Down" key while pressing the Power key
7. Follow the instructions on the screen... (remember you need at least 50% battery power just to make sure everything goes as planned)
8. Soft Reset after your done and you have a "Fresh" Shipped ROM on your HD2!
Optional:
9. Install HSPL (use the guide that's been stickied in the ROM Dev Section)
10.Flash the ROM of your choice via MicroSD method or activesync (again, please read the Stickied guides in the ROM Dev Section)
Good Luck!

total storage 328 instead of 180 !!!
well i didnt need anything to do, i pressed and hold the up vol. and down volume and pressed the power key , it did a hardreset and my old ROM back to me , though i noticed strange thing !!!
after the hardreset back to my old ROM i checked the SD card & phone storage and i found that i have now total storage 328 instead of 180 !!!
but then i upgraded my ROM this time with legal one from HTC support site , and the total storage got back to 180 again !!!
anybody knows what happened here ?!
p.s thank u guys for the help

help plzzzzzzzzzzzzzzzzzzzzzzzz

hello all
i have i-mate jasjam its proplem is no gsm
i tried alot for flashing the radio bymany verions but it stoped and when i tried t flashing it by many roms and also the original rom it stoped on the step gsm
and if i flahed it by any rom wihout the radio it completes but with no gsm
i hope to find a resolve to this prop plz to make my phone alife again
thx for u all

This is maybe problem with hardware ! better to you go in service,bcs if you flashed with original rom and radio,he must to work 100%

thz alot for help but i need a solution do it by myself thx

Hi, can you please write down what is on the bootloader screen ?

hi aze2learn thx for trying help me
ok
on the boot loader screen
HERM100
IPL-1.04
HERM100
SPL-2.10.Olipro
thx alot aze2learn

Well, since you already have hardspl 2.10-Olipro, please make sure you flash WM6 (green welcome screen) or above because WM5 (blue welcome screen) for sure will make the device show 'No GSM' if it writes an old radio version. Try original rom for your device here first : http://wiki.xda-developers.com/index.php?pagename=Available Original Shipped WM6 ROM Versions
It is recommended to use radio version (GSM) from your carrier. You can also try other radio (if you want to) from here : http://wiki.xda-developers.com/index.php?pagename=Hermes_ExtractedRadioRoms . Some say 1.47.30.10 is the best in terms of power consumption but maybe not suitable for others (depends on carrier/geography)
Note : Only original ROMs from HTC/carrier have radio. Cooked roms don't include radio.
All the best
ps : Only HardSPLed device will allow flashing extracted radio rom. Stock SPL will stop the device from flashing.

ok man thx alot i will try and i will tell u but tell me how to flashing it by pc or by sd
thx

Try RUU first (flashing through pc using usb cable) but if you're having problem such as error 260 (no connection), you can use sdcard method since you already HardSPL your device
ps: sdcard method only works on FAT32 filesystem and non-SDHC microsd.

i tried during the pc and it gives me error 262
and i tied during the sd stoped on gsm step
i dont know what to do??????!!!!!!!!!!!!!!!!!!

mony_nana said:
i tried during the pc and it gives me error 262
and i tied during the sd stoped on gsm step
i dont know what to do??????!!!!!!!!!!!!!!!!!!
Click to expand...
Click to collapse
Hi,
Extract RUU_inside.exe (use winrar or 7zip) RUU_inside.exe is in the original HTC ROM package ... get the RUU_signed.nbh and put into a new folder.
Then use RUUWrapper from here : http://forum.xda-developers.com/showthread.php?t=298737 and put it in the same folder with RUU_signed.nbh
Boot the device in bootloader mode. In RUUWrapper, tick 2.10 (new bootloader) and is it Hard-SPL. Follow the instruction.
All the best
ps : please check your PM

hi man
its stoped again on 11%
my mind will be pumped and i dont know what to do
i do everything i think
i will be crazy

maybe your battery drained out already? if so, try turn off the phone, charge it for 30 mins and try again.
ps: have you read your PM?

its already full charged

Please don't worry too much. Since your device already HardSPL, your device can still be revive.

i hope it will be aliveagain but how?
i am too tired from searching on the internet about this prop
and i didnt get any resolve for it
i think u have mor experiance than me and u can search more deeper than me
i will be here tmorrow maybe u can find a selution
i am from egypt and u ?

I'm from Malaysia (GMT+8) and please read your private message. I would really love to help but I need extra info such as what OS are you using, what happen before you got into trouble,etc.