Related
Hi,
My wizard main battery (wiza16) was very low and the wizard stop with a message “The internal battery is very low”. After coming back home I have tried to charge but it is not taking charge and didn’t turn on anymore. I recently bought a new battery (wiza16, 3.7 VDC, 1250 mAH) thinking that it will work again but still the same problem, wizard is not taking charge or turn on.
Can anyone help me?? What can I do to start my wizard? Do I need to change the tiny little battery (which is inside the wizard)? Kindly help me.
Wizard service manual
Hi,
See if when you connect the power plug the led turns red, if yes....
If Charge light is red when plug in AC adapter, it means the main battery is not charge enough and can’t power on,
You just need to continue charge unit the light become Amber
If not, i think you have a problem.
Check if charger its working and if its pluged.
If it helps --- ftp://ftp.xda-developers.com/Wizard/Docs_Tutorials/Wizard_Service_Manual.pdf
Wizard Battery discharge completely
Hi,
Thanks for quick reply. there is no light when i connect my wizard with PC. I don't have the AC charger, I have lost that for long and was using my PC usb to charge. trying to get one AC charger.
There was no problem with my wizard, just can't turn on after it's battery discharge completely. Even the new battery couldn't turn that on.
You'll need the original charger if the battery has complelty discharged as it will only charge from the computer if the phone is powered on.
This happened to me before.
There is a trick to giving the battery a quick charge which will give it enough juice to boot the phone up and allow it to charge from usb. its not recommended but works.
You will need a spare usb cable, cut one end of, strip the wires back and connect the red wire to + and the black to - on the battery, only do it for a short period, about 30 seconds while conneted to your computer.
You may need to give it a few 30 second bursts to give it enough juice.
Pop the battery back into the phone and switch it on while pugged into the PC
Took me a few attempts to get enough charge in the battery for it to boot up.
Wizard battery
You can also use a 9V battery to jumpstart your battery. But then you have to be more careful. I connected the 9v battery to my Wizard battery for about 15 seconds, then tried to start up my device. If not successful I started again with 15 seconds jumpstart..
But you can find more information here in the forum: just search for jumpstart or something similar....
Regards
huibuh_!
Wizard Battery discharge completely
Thank you all for information. 9V battery method didn't work for me. Looking for AC charger online and get a link (http://www2.dustin.se/pd_5010073700.aspx). Do you think this is the right one? If yes, then I can order.
yea that's the right one but if you have a friend with a ppc or maybe a razor you can use there charger most ac adapters are starting to use mini usb just a way of saving some money even though having an ac adapter is good
could also try and get one of those usb plugs that you can plug up to a wall and plug in a usb cable into the slot
but don't take my word for this wit hmy wizard i haven't had it shut all the way day
if anybody can verify this would work
AC charger not also working
I have got the AC charger yesterday. When Connect the Ac charger first time the red light on my wizard showed for just half second then dissappear. Still let that connected for whole night but no response.
Thank you all for help.
@Keland44, most Razr chargers dont work, they MUST be at least 850mA in order for the Wizard's battery to receive anything. The older Razr chargers are sometimes as low as 350mA, but the never ones are as high as 1.2A, so you need to read the label on the charger itself to be sure.
ashasaur said:
@Keland44, most Razr chargers dont work, they MUST be at least 850mA in order for the Wizard's battery to receive anything. The older Razr chargers are sometimes as low as 350mA, but the never ones are as high as 1.2A, so you need to read the label on the charger itself to be sure.
Click to expand...
Click to collapse
Yup that is about right,
If the battery is complelty dead, then you need to original charger.
If you have got the right charger and you get a red light and it goes off. your phone might have a problem.
This happened to my last wizard after stupidly trying to dry out the screen after getting it wet which stopped the touchscreen working (i was drying it out while the phone was still on) well my wizard crashed.
Took ages to get it back on but it was very unreliable then one day, it wouldnt go on and charger done nothing. Unpluging and pluging the charger in several times got a red light on.
Sometimes i could get it to turn on, the charger would charge for about 5 minutes then the phone would die soon after.
Your phone might possibly be bricked.
Help :
I Have Same Problem with my wizard
Yesterday my wizard goes died, i think the battery out
when i came home, i use AC Charger for HTC Universal, for 1st time its red light then off,
after 15 minutes orange light, i try to turn on my wizard and works but only in boot loader 5 minutes again its going off again
until now my wizard wont turn on
some body help
Hi Guys
I have a problem with my TyTN at the moment.
My device is not charging.
Yesterday i put it in my Docking Station and wait a little time.
But Now the Tynt isnt charged.
I think ist a Problem with my TyTN Hardware.
I have all Power Supplys used they i have, but it doesent work.
Can you help me?
Its this a problem with the accu or a fuse on the circuit ?
Sorry for my broken english i hope you understand me.
Regards Patrik Laube
Hello,
first of all, try to soft reset the device.
If it fails, hard reset it.
If it doesn't work, go the service center.
Good luck
The above advice is fine. But you did not say if any of the LEDs are lit.
Do you get the red NO CHARGE LED?
Does your phone operate normally except for not charging?
Mike
Hello
My Phone is working fine but i cant charge it with the original HTC adapter.
I must load the accu with a special loader.
USB and Charge dont work....
And i have no warranty I cant send it to my operator.
When i plug in the USB Cable it doesent make everthing.
I think it was a to high voltage on the USB or the USB Ground ( - ) had a electrical Power for a litte moment.
Have you an idea?
Thanks for yur help.
Regards Patrik
I had a similar problem, which was sorted by a new rom, but I ascertained it was software problem when I realised it charged when powered off.
PatrikLaube said:
Hello
USB and Charge dont work....
And i have no warranty I cant send it to my operator.
Have you an idea?
Thanks for yur help.
Regards Patrik
Click to expand...
Click to collapse
hi,
try this: when your device is connected via usb, tab on the battery icon in the taskbar on you device, go to the register "advanced" and check/uncheck "When Device is turned on, do not charge the battery when connected to the pc"
thats it
greetz
mizi
I'm having an issue along these lines, also.
My phone has been working fine untill the other night when I tried to charge it via the wall electrical outlet. It will not charge at all, the battery has been drained to nothing and I can't turn it on. The yellowish light doesn't turn on when I plug it in like it used to.
I don't know if this is a battery issue or an issue with the USB connection inside of the phone. On a side note, when it did have power and I tried to connect it to the USB via the PC; it didn't work. The phone was on, but the computer didn't even notice the phone was plugged in. That leads me to believe it would be a connection issue; but I'm not quite sure.
If anyone has anything they can add to this I would appreciate it, thank you.
P.S. Bringing it to a service center is a bit out of the question in the mean time seeing as it was bought on eBay and funds are limited for the time-being.
MiZi666 said:
hi,
try this: when your device is connected via usb, tab on the battery icon in the taskbar on you device, go to the register "advanced" and check/uncheck "When Device is turned on, do not charge the battery when connected to the pc"
thats it
greetz
mizi
Click to expand...
Click to collapse
Hello, I cannot find the "When Device is turned on, do not charge the battery when connected to the pc" in my device. My Rom is WM6.1 CE OS 5.2.20273 cooked by dvha79_ddt.
My HTC TyTN has the sample problem, but i can use the USB to charge normally. It cannot work using my AC adapter Only when the device is open...
About your Battery Issue.
I'll tell you exactly why ur phone isnt charging anymore... If you have been charging it alot on the USB or pretty much any!! charging on the USB u have killed ur battery, never charge your phone on the USB it kinda sucks they should make these phones able to be Sync'd thru USB without a battery cause these batteries should not be powered thru the USB over Time... from syncing to your pc will kill these batteries i have noticed that when u sync this Tytn Ithru USB and the device is at say 70% it charges up to 100% pretty fast i would recommand to you and anyone who reads this dont sync your TYTN or any HTCC phone for to long to the USB Cause it will Trash your batteries Life down the road... Hope this was HELPFUL.
Cheers
Paul
PatrikLaube said:
Hello
My Phone is working fine but i cant charge it with the original HTC adapter.
I must load the accu with a special loader.
USB and Charge dont work....
And i have no warranty I cant send it to my operator.
When i plug in the USB Cable it doesent make everthing.
I think it was a to high voltage on the USB or the USB Ground ( - ) had a electrical Power for a litte moment.
Have you an idea?
Thanks for yur help.
Regards Patrik
Click to expand...
Click to collapse
hi, did anyone solve this problem ? ive got the same problem with my htc touch cruise, i think it charges when turned off but doesnt when on. the orange light doesnt turn on when i plug usb to charge it and it doesnt sync thru the PC neither.
Does anyone has a solution to this ?Thanks a lot!
does anyone has a solution to this ?
hi, did anyone solve this problem ? ive got the same problem with my htc touch cruise, i think it charges when turned off but doesnt when on. the orange light doesnt turn on when i plug usb to charge it and it doesnt sync thru the PC neither.
Does anyone has a solution to this ?Thanks a lot!
^I'm having the same problem with my herm200. I did the soft reset, hard reset changed ROMs but still the same problem. I don't think it's the usb connector because if it is it wouldn't have been able to charge the phone even if it's turned off. Before I'm able to charge it turned on but it would take a few minutes before the orange led turns on, but when I use the phone or if I receive a text the orange led would turn off it's like the charger disconnects but after a few minutes it would go back again. Now it just wouldn't charge turned on, sometimes it gets worse where it just wouldn't charge on or off.
Now I'm already planning to buy an external battery charger.
gypsygirl13 said:
^I'm having the same problem with my herm200. I did the soft reset, hard reset changed ROMs but still the same problem. I don't think it's the usb connector because if it is it wouldn't have been able to charge the phone even if it's turned off. Before I'm able to charge it turned on but it would take a few minutes before the orange led turns on, but when I use the phone or if I receive a text the orange led would turn off it's like the charger disconnects but after a few minutes it would go back again. Now it just wouldn't charge turned on, sometimes it gets worse where it just wouldn't charge on or off.
Now I'm already planning to buy an external battery charger.
Click to expand...
Click to collapse
Are you using an official 1000mA charger? (Not a 500mA one) 500mA ones work, but they are under-powered and can cause strange behaviour, like not charging whilst turned on or whilst on a call. Similar problems can be found with car-chargers that will not charge until the device is soft reset.
Mike
^no it's not the official charger, I have this usb wall charger called Power Juice (phone and mp3 charger).
Input Voltage: AC100-240V
Output Voltage: 5V
Output Current:1000mAh
Do you think it's because I'm not using the original charger?
fixed my charging problems
The boyfriend told me to try a new cable for my charger so he bought me a 5pin usb cable, tried it at home and it worked! I still need to turn off the screen sometimes but that's ok at least I don't have to turn off the phone anymore. Now my battery charges less than 3 hours.
Hold both SoftKeys and Then press the Power button
Or you can also hold both softkeys and then put your stylus into the reset hole.
answer why it does not charge through the usb
Sorry for the very very late response. Under electrical legislation all hand held electrical devices must be insulated and fused. Some of the chargers that you can purchase are sealed without fuse which indicates that the phone has a fuse contained within its circuitry (or there may be 2 fuses one in each device) .
The problem you have encountered is that you have connected your phone to a computer or mains supply to charge. There has been a surge in the electrical supply either on connection or by un-connecting from these supplies (e.g. connect to the computer as it is booting would see a 65w signal through the USB) and this more often than not blows the fuse which sits on the PCB (printed circuit board) just after the usb connection internally to the phone.
you can either have the fuse fixed for 20/25 gbp or you can purchase a new circuit board or you can use an external charger for the battery. As it is only the power input point that is faulty.
hope this helps
Since we are at this non-charging & battery issue, I would like to ask this question on the D838pro. My battery won't charge even after 24 hours of charging. The red LED blinks thru the whole process. The LED did not turn on to orange or green. It is the battery problem because my spare battery works well. I would like to know what is wrong with the battery as I am willing to strip down the battery. Could it be the battery circuit or wiring that had fired?
cyberdroxxx said:
Since we are at this non-charging & battery issue, I would like to ask this question on the D838pro. My battery won't charge even after 24 hours of charging. The red LED blinks thru the whole process. The LED did not turn on to orange or green. It is the battery problem because my spare battery works well. I would like to know what is wrong with the battery as I am willing to strip down the battery. Could it be the battery circuit or wiring that had fired?
Click to expand...
Click to collapse
Never tried stripping down a battery, some things... well, just don't seem worth it. However as a learning exercise it might be interesting. Without lots of testing on a good battery with a multimeter then I have no clue what the readings should be between all the contacts. (Now there's a little job for you) It is as likely the internal structure of the battery is screwed as it is to be a wiring problem.
If you solve it you can certainly report back here
Mike
Is there a connection between the hardware and the software?
My hermes (as weird as this may sound) has this problem where. if I put my charger in, and slightly move it around, it will no longer charge and pulling the charger out and back in does NOTHING
If i connect my phone to my PC via USB.. it will work, but if i want to connect it back to the regular wall charger, it won't charge until I completely shut the phone off, then turn it back on.
However, with my phone turned off... whether it's on the USB connection to PC or wall charger, i can jiggle the wire and do all sorrts of stuff and the orange charge light will stay on...
anyone know what this means?
I don't know but I'm having the same problem.
Hi all.
I've bought a XDA IIi the XDA shows an orange/red blinking light when charging it trought a USB Cable to PC. According to the manual, it should be an amber solid led when charging it. The only solid led I've seen is a green one on the charger.
I'm available to sync trought ActiveSync, but XDA shows an orange/red blinking light and one post talking about that blinking orange led was caused by a low-power charging, but i use USB Cable to PC.
I always use USB to PC cable and charge my XDA phone.
I have exactly the same problem, any solutions?
Me too, same problem but additional headache no charge via usb nor wall charger. It also blinks on original wall charger also, set off charging also. its frustrating ARRRRGH.
Need solution badly
mine too
mine does it too but only once in awhile and if i soft reset my phone it goes back to charging like i listen to music and its charging and then suddenly the stupid orange light blinks and doesnt charge my phone and its annoying?
anyone have a solution?
The problem might be a near-dead or malfunctioning battery. Using a USB cable to charge does not fully charge a near-dead battery, and sometimes if the battery has completely discharged, the cable will not charge it.
Another solution...
I'm having the same problem... When i plug the usb connector the amber LED turn's on and hold. After some time the LED start to blink. When the led is blinking the battery doesn't charge.
There are some "software based" solution, or a debuging tool???
The orange led is normal that's how it is when it is in charging mode but the blinkink led is becouse of the conection with the phone and the USB try to move the USB in the phone plug it might work cuz it workd for me.
I hope i help'd u guys
What kind of move? Do you think that the problem is a bad electric contact? I guess not... I pluged and unpluged several times...
Well it workd for me becouse if i plug the usb cable to the end it has no connection that's way i move the cable back and forth untill i get the connection.
Blinking amber
I have the same problem on my htc p3300, and when i used batti 2.4 i saw that the battery temperature is 432675.5 etc something fake temerature. This is the reason, why my pda unable to charge my battery. If you set your pda in bootloader mode, it will charge your battery!. After 3 or more times i charged it in bootloader mode somethimes the battery temp sensor works normally, and the charge is working as well. Sometimes not.
Bat you can charge your battery allways in bootloader mode.
Sorry for my English.
Try it!
Good luck!
???
smalll said:
I have the same problem on my htc p3300, and when i used batti 2.4 i saw that the battery temperature is 432675.5 etc something fake temerature. This is the reason, why my pda unable to charge my battery. If you set your pda in bootloader mode, it will charge your battery!. After 3 or more times i charged it in bootloader mode somethimes the battery temp sensor works normally, and the charge is working as well. Sometimes not.
Bat you can charge your battery allways in bootloader mode.
Sorry for my English.
Try it!
Good luck!
Click to expand...
Click to collapse
does it show any indication while charging in bootloader mode???
Hi guys,
Suddenly facing a strange problem since last night.
My x10i was running out of charge & i connected to the comp to charge while i was working. I noticed the charging speed was extremely low, so i restarted the phone to see if it would help. Did not.
Thought there is some problem with the cable, used a different cable as well, but no use.
The slow charging had stopped and eventually the phone died.
Tried connecting to the socket & charging, still no use.
The red led blinks when i connect the phone to a charger via the usb or the socket.
needless to say the phone does not even boot up now, obviously for no charge...
any ideas wat maybe wrong or wat i could do ?
please advice
Have you tried to let it charge for some time in off mode? As long as your battery is not dead, and the phone get the right voltage through the USB connector it should charge in an "emergency mode". This is a slow way of charging, but allows for charging without any electronic circuits to monitor it, it is not the same as the charging screen that usually displays when you connect the phone while it is powered off. Usually when a phone is completely discharged it needs to be connected at least 15 min, sometimes a lot longer, before the electronics kicks in, and starts the speedcharging.
My best advise would be to connect it to the mains charger, or a USB port you KNOW supplies power. Some laptops cut down on the powersupply to the USB ports when they run on battery. Let it be connected for a long time (several hours), and then try to power it on again.
If that does not help three things can be wrong
1. Somewhere the USB connection is broken, either in the cable or in the connector on your phone (or on the PC's connector, but that is less likely).
2. The battery is dead, modern batteries contain circuits that actually disables the battery when any given parameters gets outside the defined limits. This is to prevent the battery catching fire. On some batteries this renders the battery useless, and you need a new battery.
3.) The mainboard of your phone is dead, and hence nothing works, can be ruled out if you can borrow a battery from someone to test if your phone works then.
I hope a good and long charge can sort out your problem, that is the easiest fix, and it is free.
Hi O_K,
well, i have been charging (or trying to) the phone since it died last night.
i have used different chargers & different modes of charge (through the system & the wall socket) - no joy at all.
the LED blinks red a couple of times when connected.
Very occasionally, the SONY ERICSSON logo (startup) shows on the screen & it switches off again, back to the blinking.
So charging for a long time & through different chargers has not helped.
gonna try a different battery now to see if that can help.
Thanks for your response!
well, tried switching chargers & batteries.
The problem seems to be with the charging unit on the phone (USB)
with any charger or battery, wen connected the led blinks (like wen the phone is charging), but there is no charge happening.
eventually the phone dies, even if charging
any ideas?
There is a thread some where in this forum for fixing the same problem you have...I don't remember the exact name of the thread..if I find it I'll post the link here..Anyways what the guy did was
-Pull the battery out and connect the charger till the led turns green.
-put in the battery now and charge the phone...
and I think that was it.
Hope it helped..
EDIT: Found the link.
http://forum.xda-developers.com/showthread.php?t=944322